Cisco WAN :: 4948 Trying To Replicate Config For Qnq Layer3 Interface
Apr 9, 2013
I am replacing a 7204 router with a 4948 and am having trouble trying to replicate the config for the qnq Layer3 interface.A bit of background - I am a service provider where I have an interconnect with the carrier, who pass off WAN links to me as a standard VLAN Ids. Some of these VLANs however I can do QnQ.
This works fine - but I can get the second-dot1q 50 command working properly
View 14 Replies
ADVERTISEMENT
Apr 23, 2012
I'm trying to add an outbound policy on Layer3 interface on a 6500. The will be used to prioritize voice traffic. The environment contains 2 sites with 2 6500's each with VSS and a metro Ethernet link between them. I seem to be having problems prioritizing the voice across this link.
View 1 Replies
View Related
May 1, 2012
i have a requirement to enable pbr in vrf interface of a 4948 switch. but as i browse the internet, it is quite impossible to do that. is there any alternative way / feature to get the same result as pbr does? which is to reroute the specific vrf traffic to another interface based on source and destination ip address?
View 1 Replies
View Related
Aug 17, 2011
Cisco 2951 w/ HWIC-4ESW
IOS 15.0(1)M5
#sh ip flow int
Vlan533
ip flow ingress
ip flow egress
#
The SVI sends the flow data just fine, however I also continue to receive flow data from most other interfaces.
I have attached a screenshot of one of our netflow collectors indicating that many of the interfaces are sending flow data even though not configured to do so. We have two different netflow collectors, from different vendors and both confirm the same interfaces sending flow data.
Normally I wouldn't care and ignore it, however one of them uses a license limit by interface and is a bit problematic.
View 2 Replies
View Related
Sep 15, 2012
I have WLC 5508 with 6.0 software and kept in main office and 10 sites are connected . I created Group and hreap for the sites AP.Now customer wants the secondary WLC to keep on one another site. And the customer is asking all the configuration like ap group and all should come to secondary wlc automatically . In future also if he create any new group in primary it should come in secondary wlc.And if primary goes down the secondary should controll all the sites and when comes up primary should taken care.Active standbye mode.
View 10 Replies
View Related
Apr 20, 2011
I have a sitecom 3G ready wireless router but does not support the local telephone company. i would like to know how to access its modem config from a command line inorder to configure the modem commands with local company settings. Its model no is WL-326v1001
View 1 Replies
View Related
Oct 3, 2012
I am not a ASA expert but I have configured them few times. I have a vision of a task I have to complete but not sure if it is practical or how to go about doing it.
We two locations, Location A and Location B. Both locations have a 100MB internet conection. Location A has a ASA 5510. Location B has a 5505. Users at both locations access the internet via their respective ASA. Location A is the headquarters and Location B is a disaster recovery site. We want to setup a tunnel between both ASAs. This tunnel will be used to replicate data between the two locations for DR purposes. We need the users to still use the same pipe to get to the internet but want to allocate 10MB for internet use and the remaining 90MB for the DR tunnel.
View 30 Replies
View Related
Jun 11, 2012
I have FWSM failover pair, Active/Active configuration, admin and another 4 context, few context active on first FWSM, other on second FWSM.I needed to add VLANs 51 and 52 to FWSMI created VLANs on both Cat6500, created firewall vlan-group 3 a and put "firewall module1 vlan-group 3" on both cat6500Then I log in in system space on primary FWSM and created interface VLAN.Created VLANs automatically occured in system space on Secondary FWSM.Then I wanted allocate VLAN 51 and 52 to context XY, so I went to part of configuration for context XY and "allocate-interface Vlan51" and "allocate-interface Vlan52".
View 1 Replies
View Related
Oct 15, 2012
Is it possible to implement ACLs in layer3 switch??
View 4 Replies
View Related
Feb 26, 2012
I have a SR520 router with the ADSL WAN built in. I am looking to ignore the ADSL port and utilise the 4 FA ports to route between two networks.Can I configure the ports on the switch part of the router to become Layer 3 and take there own Ip addresses? If so I can save myself the purchase of a new router.I have used loopbacks before but not sure that will work.
View 9 Replies
View Related
Apr 25, 2011
I'm trying to get the following running.
I have 4 Subnets
VLAN 1 172.20.0.0/16 with the default GW 172.20.200.254
VLAN 10 192.168.10.0/24 with the default GW 192.168.10.2
VLAN 59 192.168.59.0/24 with the default GW 192.168.59.254
VLAN 130 192.168.130.0/24 with the default GW 192.168.130.254
[Code]....
With absolutly the same settings I did this with an HP E4200-12G L3 Switch (which is now doing the job) so there is no routing mistake in the other components.For me it looks like, the SG300 doesn't like to be NOT the default gateway.
View 7 Replies
View Related
Jul 26, 2011
I'm setting up two vlans and I would like all of vlan 2 to only have access to the WAN router on vlan1 at 192.168.30.1.
VLAN1 192.168.30.x
VLAN2 192.168.31.x
I've setup the VLANS and static routes and I'm able to access the WAN router at 192.168.30.1 from the 192.168.31.x network and everything is fine.
I'm getting an error setting up the IPv4 based ACL that is designed to allow the 192.168.31.x network access to only the 192.168.30.1 WAN router.
The first rule I setup is to permit source 192.168.31.0 / 0.0.0.255 dest 192.168.30.0/0.0.0.255 to allow all traffic to from the 192.168.31. net to access the 192.168.30.x net. Then I was going to deny the dest of 192.168.30.1-255 but I'm not sure of the wildcard to use for that.
I'm not clear on the wildcards but I'm also getting the following error when I setup the first ACE rule:
"MIB Index is out of range.Index must be bigger then 0 and Existing ifindex.."
I suspect the error is related to how I'm using the wildcards?
View 4 Replies
View Related
Apr 17, 2012
If i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?
View 5 Replies
View Related
Jul 11, 2012
I have two 3750 layer3 switches and I need to connect them via stack cable.so if I connect them with the stack they will be act as an one switch, but for the configuration if I create a VLANs on the master switch (applied all the configuration on the master one) this configuration will be transfered to the slave one or I have to repeat the configuration that I did on the master.
View 5 Replies
View Related
Nov 15, 2009
I have a Cisco 2811 router and when I turn of the router the running config is lost. I have to the following to get the router running of the start-up config settings.
router#copy start-up running-config
View 9 Replies
View Related
Mar 29, 2012
We are about to install a new network consisting of Cat 4500s with Sup7E at the Access Layer, with Nexus 7000 at the Distribution and Core layers. We have 14 floors with at least three 4500s on each floor. Within the office block where the Access Layer and Distribution Layer reside we need to support secure borderless networking using 802.1x to place users from different parts of the business into segregated networks at layer 3.All switches will have the feature sets to support MPLS/ VRF / OSPF / EIGRP / BGP etc.We quickly dismissed the idea of using VRF-Lite due to the sheer number of Vlans we would need to managage and maintain, the point to point links alone just to get one additional VRF on each floor required far too many Vlans.As a result we are now considering deploying MPLS. The obvious benefits include scalability and manageability, the fact that all switch to switch links can now be routed, instead of having to using SVIs.
View 2 Replies
View Related
Jul 21, 2012
I have faced a problem regarding AAA line:
aaa authorization exec default group tacacs+ local
if i add this line in my cisco 4948 switch running on 122-46.SG.. The next time i telnet to the switch i get an automatic restart of the switch and all configs are lost.
IOS used:
cat4500-ipbase-mz.122-46.SG.bin
WS-C4948-10GE
View 1 Replies
View Related
May 20, 2009
I am trying to enable IP SLA on a Cisco 4948 switch (running 'cat4500-ipbasek9-mz.122-46.SG.bin') to test CiscoWorks IPM using this swtich as a source device. But I can't run the command "ip sla monitor" on this switch. It just has "ip sla responder". Is it possible to configura IP SLA on this source switch? Or can I do it only on routers?
View 6 Replies
View Related
Jul 31, 2011
how to configure QoS on Cisco 4948. I have three VLans in my network. First is video traffic second is the voice traffic and third is the data traffic . I need to set the priority in QoS in the following way
i.e. Video traffic - 1st pref
Voice traffic - 2nd pref
Data traffic - 3rd pref
how to configure for this requirement.
View 3 Replies
View Related
Aug 10, 2011
i have several Cisco 4948 in my network infrastucture, the issue that i´m having with them is when i try to view the ssh log appears something like this.. Aug 11 15:43:13 GT: %SSH-5-SSH2_USERAUTH: User '' authentication for SSH2 Session from 192.168.2.5 (tty = 1) using crypto cipher 'aes256-cbc', hmac 'hmac-sha1' Succeeded
The ip address is correct but the username is in blank i checked on other equipments (2960 access switches and 7200 series router) and they show the username field correctly...
The IOS version im using is (cat4500-ENTSERVICESK9-M), Version 12.2(50)SG1, RELEASE SOFTWARE (fc2)
The ssh configuration is as follows..
ip ssh time-out 60
ip ssh source-interface Loopback1
ip ssh logging events
[Code]....
View 1 Replies
View Related
May 14, 2013
I just picked up some second hand 4948 switches and wanted to install the embeded managment software. I can't find it anywhere in the downloads section?
is there a better FREE solution for managing these? I tried config profesional, but it only shows the routing config. There seems to be so many options.
View 1 Replies
View Related
Nov 14, 2011
our 6509 is configured as NTP master. Our 4948 is configured as NTP client.on each of these switches we have configured a management VRF.The problem is that 4948 can not synchronize its clock with NTP master. Both switches are directly connected.show cdp neighbor on 4948 switch:
6K5 Fas 1 138 R S I WS-C6509- Gig 2/2/43
interface config on 6509:
interface GigabitEthernet2/2/43
description *** Mgmt Switch Externe 1 ***
switchport
switchport access vlan 1900
switchport mode access
wrr-queue cos-map 1 1 1
[code]....
debugs on 6509 do not show any packets received or sent to 4948.
View 2 Replies
View Related
Jul 14, 2012
I cannot boot IOS, when i reload this switch it go to ROMMON. I try to uploand IOS but it still has problem. i think i may wrong some point during i did uploand.
This is problem
Switch#sh bootvar
BOOT variable = cat4500-entservicesk9-mz.150-2.SG3.bin,1;bootflash:cat4500-entservicesk9-mz.150-2.SG3.bin,1;bootflash:cat4500-entservicesk9-
[Code].....
View 2 Replies
View Related
Dec 11, 2011
I'm trying to apply the following policy route in my switch 4948, but it suddenly crash. Is anything wrong in my commands? The switch is rebooting with an error:
System returned to ROM by abort at PC 0x0
My commands are:
access-lists 7 permit 10.140.22.0 0.0.0.255
access-list 177 permit ip 10.140.22.0 0.0.0.255 100.220.24.0 0.0.0.255
access-list 177 permit ip 10.140.22.0 0.0.0.255 100.216.36.0 0.0.0.255
access-list 177 permit ip 10.140.22.0 0.0.0.255 100.216.38.0 0.0.0.255
[Code]......
View 12 Replies
View Related
Mar 13, 2013
My cisco 4948 switch is generating the below error,how do i troubleshoot this error.
*Mar 13 00:09:33.451: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 14 times)Packet received with invalid source MAC addre ss (00:00:00:00:00:00) on port Gi1/37 in vlan 1Gi1/37- to this port another 2950 switch is connected by trunk link.and to this switch end host is connected i.e.thin client
View 3 Replies
View Related
Aug 26, 2012
I am unable to input the command "ip flow-cache timeout active 1" to my cisco 2960 and 4948 switches. But i am able to do so in my cisco 6500 series switch. Hence how do i enable netflow on both 2960 and 4948 devices?My 2960 and 4948 are L3 switches. What commands or additional hardware module are required.
View 4 Replies
View Related
Oct 29, 2012
I understand that most of the cisco switches does not have a battery-supported system clock. The better solution is to setup the NTP server and let the rest of the switches to synchnorise the clock with it. How about cisco switch 4948? Does it have a battery-supported system clock?If the cisco switch 4948 is the NTP master, how I am going to make sure that the clock will not be reset after reload?
View 3 Replies
View Related
Nov 20, 2012
Create a port channel out of interface 3 and 4 of ASAConfigure 2 sub-interfaces in those Po interface (my inside vlan and the dmz)At the 4948, configure a trunked port channel out of a single interface (funny ), then do the same in the second 4948Connect ASA port 3 to the 1st 4948's single-interfaced port channel, ASA port 4 connects the same on the 2nd 4948.
View 4 Replies
View Related
May 23, 2012
MAC Support: 16000
Backplane: 18Gbps
Forward: 28Gbps
VLAN's: 4000 (q-in-q support)
Jumbo Frame Supported
Supported 8000 static routing
!Supporting Stack!
Cisco 4948 supporting stackable? which product do you recommend to these criteria?
View 3 Replies
View Related
Oct 17, 2011
I have a named aggregate policer configured on a 4948 switch running IOS 12.2(53)SG2 but can't seem to be able to monitor it using SNMP as I can't locate the OIDs (using OIDView) - I'm okay with CB and PB QoS.
View 1 Replies
View Related
Sep 19, 2012
I am updating the iOS for a 4948 the bootflash is empty so all i can get into is the rommon. There is no option for x-modem. How can I put the iOS onto this device? [code]
View 2 Replies
View Related
Jun 5, 2013
We had to transport one of our 4948 10 GE to another Data Centre and when we got it there and tried to power up its System Status LED was red and we cannot even get console to the device.
We can try to see if the switch is completely dead and needs replacing or is there something we can do to get it back up and running again?
View 1 Replies
View Related
Apr 5, 2013
So I've got an odd issue here, have an older 4948 that I'm trying to setup on our management vlan so i can manage it from another host connect to the switch. I can't figure out why its not working. Below is the config
vlan is 64 and all the trunk and access ports that are on vlan 64 are working just fine. Just can't hit the switch from a machine on the 64 vlan.
!
interface Vlan1
no ip address
[Code].....
View 9 Replies
View Related