i want to enable net flow for multicast on my 6509-E with IOS s72033-advipservicesk9_wan-mz.122-33.SXI2a. I've checked the ios via software adviser to be sure that this feature is supported: Minimum Compatible Release 5 Additional Software
I've used the command "ip multicast net flow output-counters", but that is not enough, i guess. It is required to use further interface commands like "ip multicast netflow....", isn't it? But this commands are not available:
Cisco6509(config-if)#ip multicast ?
boundary Boundary for administratively scoped multicast addresses
helper-map Broadcast to Multicast map OR Multicast to ip-address map
limit Limit multicast mroute state
[code]....
I am trying to setup Netflow to identify a problem I am having with a video conferencing system. Here are the commands that I have entered into the 6509 I am working on. I have checked this against another 6509 I have and these match. Not able to get netflow to show up on the solarwinds server. I have configured it to accept the netflow source coming from the 6509 I am working on.
ip flow-export version 9 ip flow-export destination 1.1.1.1 2055 ip flow-export sourc vlan 254
Below is the show ver of 6509 switch , how to enable netflow
sh ver Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(33)SXI7, RELEASE SOFTWARE (fc1) Technical Support: [URL] Copyright (c) 1986-2011 by Cisco Systems, Inc. Compiled Mon 18-Jul-11 05:50 by prod_rel_team
I am trying to setup netflow with on 6509 and SolarWinds NetFlow Traffic Analyzer v3.10.0
The problem I have is that after configuring the basic settings of NetFlow on both side I can't see all the traffic I expected to capture in NetFlow.
The details of my problem. I want to monitor the traffic on VLAN 20. In the general configuration of the switch I have entered the following ip flow-export source vlan 10 ip flow-export version 9 ip flow-export destination 132.5.200.123 8080
Where vlan 10 is the management vlan. Vlan10 can ping 132.5.200.123 no problem.
On VLAN20 interface I configured this ip flow egress ip flow ingress ip route-cache flow
When I go to SolarWinds Netflow Traffic Analyzer I can see maybe 1 or 2 packets flows, like nothing of the data. If I do a capture of the traffic on VLAN 20 I can see there is loads of IP traffic on that VLAN but why is netflow not capturing the statistics of those flows and reporting it to NetFlow ?
We have Cisco Catalyst 6509-V-E VSS Switch with Sup2T und IOS Version 15.0(1)SY2. We are gettin input netflow information from the gi2/3/7 but not output ... I am not sure why it does not work.
I hve the above setup and I need to setup multicast between the 2 servers. The nexu7k is a layer 2 switch and the 6500 is a lyer3.Both servers would be sending/receving traffic.
I am trying to configure the NLB multicast for the Microsoft exchange. The moment I am enabling the NLB my core switch 6509 CPU is reaching 100% and whole network getting down. [code]
I thinking I am putting wrong command. I am not able to see the disable-snooping in 6509 Switch.
I am aware that the 3750 switches are not able to support Netflows, so I have created a SPAN port and spanning traffic from a specific port. I would like to create a seperate VLAN and trunk the traffic from the SPAN port down to the 6509 switch and then capture all the traffic for that VLAN on the 6509.
The two servers (red hat) use multicast for their heartbeat. Unrouted vlan 99 (only layer 2) is configured on the VTP Servers (6509).I have read this document [URL]
Switches 1 and 2 have IOS: c2960s-universalk9-mz.122-55.SE3.bin and the 6509: s72033-advipservicesk9_wan-mz.122-18.SXF17a.bin
IGMP snooping is enabled on the 2960 switches.In order for the heartbeat of the servers to work, I have tried these solutions:disable igmp snooping for vlan 99 on switch-1 & switch-2. (No additional action was taken on the 6509). This didn't work. I expected that the multicast traffic would be sent as broadcast throughout the network, but for some reason it didn't work.on switch-1 & switch-2 configured "ip igmp snooping vlan 99 querier" (no additional actions on 6509). Didn't work either.on switch-1 & switch-2 configured "ip igmp snooping vlan 99 mrouter interface gigabitEthernet 1/0/25" & "ip igmp snooping vlan 99 mrouter interface gigabitEthernet 1/0/26" for the two connections to the 6509. Again no actions taken on 6509. Didn't work. I want static mac entries on the switches to be my last resort, since the number of red hat servers on the network is going to increase and I want to give a more generic solution to the issue.
We want to implement multicast on our network. We are going to use for online teaching purpose. I am very new at Multicast and not have much idea about it. We are not running any routing protocol in our network, only static route. The multicast server is located at One of our office and it is connected with L2 (Cisco 2960) switch, L2 switch is connected to L3 switch(Cisco 4948). L3(Cisco 4948) and Core Switch(Cisco 6509) with FWSM are connected with E-3 link with tunnel. Router 1 and Router 2 are connected with P2P ILL links which are terminated at serial interface. The Multicast Server IP is 192.168.2.131/25. The scenario of our network are mentioned below:
We have created a seprate vlan (i.e. vlan 102, interface IP is 192.168.2.129/25) for multicast at L3 switch, enable multicast routing, defined rp-address(i.e. 192.168.2.129/25), enable sparse-dense mode at multicast vlan as well as at some other vlan also for testing purpose and joined multicast group (i.e. Multicast IP is 224.3.3.5). At core switch we have also enabled multicast routing, defined rp-address (i.e. 19.268.2.129/25), enable sparse-dense mode at user vlan and inside vlan of FWSM and joined multicast group at user vlan and inside vlan. At FWSM we have enabled multicast routing, defined rp-address(192.168.2.129), doesn’t find any option to enable sparse-dense mode and joined Multicast group at inside vlan and router 1 vlan. At Router 1, we have configured the same thing. We have configured mroute at all the devices. We are able to ping from end to end. We are testing multicast by Multicast IP checker tool (provided by vendor). Multicast is working fine at L2 switch, L3 switch and Core Switch, but not from Router 1. Ping is reachable from Router 1. After doing mtrace at Router 1, the following output has come:
Type escape sequence to abort. Mtrace from 172.21.254.50 to 192.168.2.131 via group 224.3.3.5 From source (?) to destination (?) [Code] .....
If , we do mtrace from gateway IP address(i.e. 192.168.2.129) as destination address then mtrace is getting completed, but if mtrace is done from Mutlicast server IP address(192.168.2.131) as destination address, then mtrace is not getting completed.
We have connected one laptop at Router 1 vlan to test Multicast. The host, which is connected to Router 1 vlan is able to send multicast packet to other host and other host at different vlan are receiving it , but it’s unable to receive multicast packet send by other host of different vlan.
Do I need to enable igmp snooping at L2 switch, L3 switch and Core Switch ? I am not able to understand or can't figure out where i have configured wrong.
How is it i can implement the command 'ip multicast rate-limit out group-list <access-list>' but i get the error "ip multicast rate-limit" command is not supported on 6509?
Is it an IOS limitation or a limitation of the switch series and subsequently can't be used at all?
I have a problem on my catalyst 6509 on which I would like to do the following things :
I have some Vlans in which multicast is enabled. In tose Vlan theres is a router which is default router for equipements.
I had enabled multicast routing because some Vlan needs to exchange multicast informations, but I wolud like to make difference between Multicast traffic. For example I have 5 vlans:
Vlan 1 and 2 need to exchange Multicast informations but the don't need multicast information from Vlan 3 and 4 Vlan 3 and 5 need to exchange Multicast informations but the don't need multicast information from Vlan 1 and 2 Vlan 5 is independant Vlan but doesn't need to have multicast information from all others vlan.
Last problem, equipement on differents vlan can use the same Mulkticast group address. In this case, Multicast routing is not working between Vlan 1 to Vlan 2 and Vlan 3 to Vlan 4.
Any major difrrence between Netflow v/s Netflow-Lite?
I am trying to understand if Cisco 4948E can do the same job as Cisco 4500E or not and difference between Netflow v/s Netflow-Lite will work for me to select correct product.
I try to pass multicast traffic between two vrf on the same 3750 switch. I have IP services IOS and sdm template routing.
here is my config:
ip routing ! ip vrf vpn2 rd 1:1 mdt default 232.1.1.1 route-target export 1:1 route-target import 1:1
[code]....
Now I'm stuck - I don't know what to do to pass multicast traffic. Do I have any chance to run this config on 3750 chassis?Perhaps "Configuring Multicast VPN Extranet Support" document will be useful, but it concerns Catalyst 6500? [URL]
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports x1 NAM x2 Sup720 Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports x1 NAM x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
How NetFlow works when NAT is enabled in the Cisco Router? ...the translation of IP addresses is done before or after save the packets in the flow caches?
i just came to know Assurance feature license doesn't come for free when upgrading from LMS4.2 or NCS1.1. It has to be purchased. Before buying this license, i would like to know if IPv6 netflow is supported.
I have an issue with Netflow that I have been unable to solve. I have an ASA5510 that is sending netflow data to a FogLight NMS and it works fine until I reboot the server. After the server is rebooted, the flows no longer are received until I reload the ASA. Once the ASA is rebooted, flows work fine. I can remove and reconfigure the netflow configuration on the ASA and that will start the netflow again, but that is painful.
Is there any way to easily stop/restart or re-initiate the netflow from the ASA easily?
I see these errors on my 6500 router which acts as my server farm and has hundreds of servers connecting to it. I have just taken over these routers from another guy and think the errors may have been there for quiet awhile. I have another router which doen't seem to have these errors. Can you tell me how to turn off netflow? Will it cause any problems to my server farm? Is there a risk to the router if I disable something?
I ask this cause the server guys are having problems with certain servers. I am not sure if they are because of this or not. I really would like to clear the logs. [code]
I was trying to get Netflow setup on one of my 7K VDCs and ran into a problem. While netflow data was reaching the collector, IP src/dst information was not appearing in the analyzer tool. I could not see any information about conversations. So I contacted the company that makes the collector/analyzer and the directed me to a blog on their site and told me to setup the 7K exactly as it is described in the blog post. I did and a bit later the ip src/dst address information appeared. So the only difference between the two configurations was that in the first case I tried to define a record and in the second case, no record was defined and instead the orginial-netflow parameter was used in the "flow monitor" section. [code]
I referenced the document "Cisco Nexus 7000 Series NX-OS System Management Configuration Guide,Release 6.x", Chapter 19 - Configuring NetFlow.It's clear to me that I didn't do something right in defining my own record since that's really the only difference between the config that worked vs the config that didn't. However, the documentation I referenced doesn't really provide useful information about how to create a record (above and beyond what I can already see by typing '?' at the CLI).
For example, the "match" command makes no sense to me. Usually when you have a match command it is accompanied by some sort of ACL. In the "flow record" section a match command would be something like "match ipv4 source address" but that's it. What does that mean? Match anything that has a IPv4 source address?? That doesn't make much sense. The collect commands are equally as bewildering. If I want to define my own record (and not use the original-netflow parameter) what do I need to do in the "flow record" sub-configuration to get Nexus to send ip src/dst information to the collector (which, I would think, is basic information to send - what good is netflow data without it)?
I have a question regarding netflow and NAT. I have read some documentation (on ASR1000) regarding monitoring NAT process on Cisco ASR1000 that can be done using netflow version 9 (the term was called netflow event logging a.k.a NEL). The problem is, I have not found the netflow collector that can do that. I have queried several software such as manage engine "Netflow Analyzer" and Lancope, but they said their software can not do that.
We have a 1841 router and would like to enable netflow. Will this degrade the router's CPU and memory performance.
1841>sh verCisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(1c), RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2005 by Cisco Systems, Inc.Compiled Tue 25-Oct-05 17:10 by evmiller
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
1841 uptime is 1 day, 4 hours, 47 minutesSystem returned to ROM by power-onSystem restarted at 11:04:25 MYT Mon Jan 10 2011System image file is "flash:c1841-ipbase-mz.124-1c.bin"
Cisco 1841 (revision 7.0) with 114688K/16384K bytes of memory.Processor board ID FCZ113311Y62 FastEthernet interfacesDRAM configuration is 64 bits wide with parity disabled.191K bytes of NVRAM.31360K bytes of ATA CompactFlash (Read/Write)
I have an interface e0/4 that is 172.1.1.1 on router one (network one) which links to another router (onnetwork two) which has an interface of e0/4 172.1.1.2 which allows two networks to communicate. Network one is 192.168.0.0 /24 and network two is 10.255.255.0 /24.
How do i configure netflow to monitor the traffic going through these interfaces?
I have a WS-C3560X-24P with this SW version 12.2(55)SE1. It has several L3 Vlan interfaces.How do I enable it to send Netflow traps?It does not support the ip flow-export commands.
I have a 7200 router with a 12.2.(46a) IOS and I am trying to activate Netflow on a subinterface. From the documentation of Cisco, I should be able to do it since the ios 12.2.(14)S but the command is unavailable.
[URL]
I have tried also to enter the command in the subinterface directly but it doesn't recognize it.
5505 ASA, 8.2(1) ,We can not get it to report Netflow to the collection agent at 192.168.1.34. Here is the commands I've entered:
asa# show run | i flow access-list netflow-export extended permit ip any any flow-export destination inside 192.168.1.34 2055 flow-export template timeout-rate 1 flow-export delay flow-create 60 class-map netflow-export-class match access-list netflow-export flow-export event-type all destination 192.168.1.34 policy-map netflow-export-policy class netflow-export-class flow-export event-type all destination 192.168.1.34
We are attempting to configure Netflow and export to a colloector. We have the following configuration applied to the device, we can ping from within the vrf to the destination of the flow collector
ip flow-cache timeout active 1 ip flow ingress layer2-switched vlan 1,800-801,803,821-823,861-862,871,900,998,1100-1107,1121,1200,1221,1301-1302,1321-1322 mls netflow interface mls flow ip interface-full ip flow-export version 5(code)
however we do not receive the flows on the collector. We can see the flow for both hardware and software but cannot see them at the collowctor.
Recently bring up a new Router connected to ISP A and the Netflow collector/server is located in different location and they are connected to ISP B. I have enabled snmp and netflow config on my router(2911) but not receiving the netflow packets are not reaching the server for due to some strange reason whereas other packets like ICMP for snmp are reaching the netflow collector.Finally,I created GRE tunnel between the two locations routers and set the route for the netflow collector/server to the tunnel other end IP. In this way the netflow traffic are reaching successfully to the server.
