Cisco AAA/Identity/Nac :: ACS 5.2 Radius Accounting From ASA And Juniper?
Apr 10, 2013
i changed from ACS 4 to ACS 5.2. Everything works fine but i have authentication failed in the Radius accouting reports every time when users connect through ASA or Juniper into our network. Juniper amd ASA only send accounting informations to ACS. The users are not configured on the ACS, authentication is done via external LDAP. So my question is why do o see authentication error on ACS because Juniper and ASA only send accounting packets ?
I am trying to authenticate on Juniper NSM express using cisco ACS 5.2. The request is arriving at the cisco ACS but i am getting the following error.RADIUS requests can only be processed by Access Services that are of type Network Access.
Several of my older netscreen devices only support radius authentication and I'm having trouble migrating them from ACS 4.2 to ACS 5.1. When I try to authenticate, the authentication passes in ACS but it doesn't log you into the Netscreen (you see a auth failure in the Netscreen logs). I believe that the custom attributes are not being passed from ACS to the Netscreen. The custom attribute we are trying to pass is "NS-Admin-Privilege" with type integer and a value of 2. The netscreen is setup so that the user privledges are obtained from the ACS server.
Any setup where they are using Cisco radius authentication to authenticate Netscreen devices?
on the dashboard of the "Monitoring & Report Viewer" I see a lot of system alarms related to the database.The explanation of the alarm says to look at the Collector logs for the details.
I have a WLAN configured with 802.1x PEAP pointing to an external RADIUS server. It works fine for the most part, but I'm having problem closing accounting sessions in RADIUS. I've found this is related to the client table in the WLC. The user session does not end in RADIUS unless the WLC officially removes the client from the db, which takes 5-6 minutes from what I can see (probably due to the default idle timeout of 300 seconds).
For example:
1. I connect my tablet to the test WLAN. It associates and authenticates successfully and the WLC sends the accounting info to my RADIUS server, opening up a user session. If I turn off the wifi in the tablet, the client entry stays in the WLC client table until it times out. The WLC removes my tablet from the client table after 5-6 minutes, and then the session closes in the accounting table. I can force the session to close much earlier by manually removing the client from the WLC.
2. Same as #1, but this time instead of turning of the wifi in the tablet, I choose to connect to a different WLAN in the WLC. The user session in the accounting DB never closes. If I reconnect back to the original test WLAN with 802.1x, it opens up yet another user session in RADIUS accounting. Now I have a "dead" user session in accounting that is going to be open forever unless I delete it from SQL.
Is this an issue with the end user client not sending the disassociation frame properly, or a config problem with the WLC? How can I make it so that every time a client drops from an AP or moves to a different WLAN, the WLC would immediately send accounting updates to my RADIUS server and close the user session properly?
I am using the CISCO SG300-28 with firmware version 1.0.0.27. I enabled RADIUS authentication and accounting. Authentication is working but there are no accounting requests/replys (Accounting on, accounting off, accoun ting start, accounting stop) when running RADIUS in debug mode. I also did a packetcapture and there are no accounting packets.
So i updated the firmware image up to version 1.1.2.0. When I now want to configure accounting in RADIUS settings then there isn't any option to set an accounting port.
Ich checked the data sheet of the switch and it says that accounting is supported:
=============================================== 802.1X: RADIUS authentication and accounting, MD5 hash; guest VLAN; unauthenticated VLAN, single/multiple host mode and single/multiple sessions [URL] ===============================================
I did a second packet capture with the new firmware image and there are still no accounting packets.
The RADIUS server is configured correct for accounting because when using another NAS like a WLAN-AP with DD-WRT accounting is workings. It is working with pfsense Captive Portal (an open source firewall and routing solution with a hotspot portal).
Need deployed accounting method to log Anyconnect session details ? Do you do it via a radius server or via logging messages to a syslog server ?
Any appropriate configuration ? I am looking to log successful and unsuccessful authentications as well as session length, log on and log off times.
I've been playing around with Anyconnect authenticating to AD via ACS 5.1 but can't seem to get the accounting details I require. Similarly I have tried to catch appropriate syslog messages but again without much success.
I have a Cisco ACE 20, and I´m trying to set up a serverfarm for my radius server to load balance ldap udp accounting packets. The ACE has an LDAP authentication probe but I see no native way of setting up an LDAP accounting probe, without resorting to probe scripting.
I have set up an ACS 5.4 box and have some test devices connected to it.Cisco and Juniper, both working fine using TACACS I can connect to both using SSH or Telnet but my problem is the J-Web Juniper GUI I can access the J-web no problem with the root account. i can not seem to get it to work, no matter what I try. Here is my shell from the ACS box And the following Juniper configuration. I have tried binding the local-user-name attribute to both the remote and remoteadmin with no luck.
version 9.6R1.13; system { host-name Juniper-Firewall; authentication-order [ tacplus password ]; root-authentication { encrypted-password "$1$1tRuy9o2$LwSPxNwe4XGNMOMIMo1pd1"; ## SECRET-DATA
I've got an issue with my ACS 5.1 implementation not updating any of the RADIUS or TACACS authz, authc, or acct records. Nothing is showing up, even though i've logged in via TACACS to several devices, and there are numerous wireless devices authenticated and online via RADIUS right now.
How to configure ACS 5.1 local administrator accounting and where have to check the accounting log . suppose administrator logged in to ACS and created some user or delete users where will see the log , which user have they created or deleted.
ACE is configured to point accounting to ACS servers but ACS servers are not seeing all the accounting logs. I can only see accounting logs from ACE for watchdog, start and stop.
Following best practices on cisco documentations we did set aaa acounting update periodic 5 with 250 switches in the deployment every single switch is geneating and sending 9.990 acct records this is too much the new testing parameterswe are using is aaa acounting update newinfo periodic 15 and this lowered accts by 2/3 (3500) moreover from switch monitoring the most accts records sent by it are related to the trunk-port any suggestion to mitigate this informations storm rather than raising the 15 min period to higher values?are this records generating from the trunk port normal?
In the process of migrating from ACS 4.1 to ACS 5.3. Authentication works fine, but having issues with authorization on the Juniper WXC-3400 devices. In ACS 4.1 we were passing TACACS+Shell (exec) Custom attributes Privilege level=15, which allowed a user to login with read/write privileges. In ACS 5.3 tried setting the Shell Profiles common task to 15 for both Default and Maximum (one at a time, and together), as well as setting the Custom Attributes for priv-lvl=15 (with and without Common Tasks set).
I am setting up reports for tacacs accounting on ACS 5.3. However, accounting only seems to work after entering enable mode on the switch. I would like to see all commands, even the enable command when in privlage 1 mode.
I've set up my 5540 ASA to accounting commands on TACACS+.Every moviment done through ASDM is logged on TACACS+ by this form: cmd=perfmon interval 10.What does that mean?Why doesn't it record the exaclty command I'd issued?
Having an issue with authenticating Juniper J Series and SRX devices with ACS 5.1 The devices can authenticate using TACACS to ACS 5.1 via the CLI (telnet / ssh connections) but cannot using the JWEB management page.Doing packet captures between the Juniper devices and the ACS 5.1 box shows the Authenticate phase passing, but it does not progress onto the Authorisation phase. There is nothing of interest in the ACS Logs (Even with the debugging levels turned right up) The same Access service is in use for both the CLI and GUI (JWEB).Using ACS 4.1, both CLI and JWEB authentication works.[URL]I'm thinking the issue is with ACS 5.0 / 5.1 and it maybe not liking the response from the Juniper (even though it should be the same mechanism)
I wants to inegrate Juniper netscreen firewall in Tacacs Cisco Acs 5.1.As I go through Juniper KB which mentioned that I need to enable Netscreen Service in Cisco ACS 5.1. how to enable Netscreen service in Cisco Acs 5.1 and how I got Further to integrate Juniper Netscreen Device in Cisco cs 5.1
I have configured ACS 5.1 and using Tacacs. I have two juniper SSG140 FW's in different subnet. Tacacs authentication is working on one SSG140 FW, but not on the other one. Tacacs configuration on both FW's are exactly the same. Both FW's have been added in the ACS server with the same shared secret key same profile etc. I don't even see the authentication requests from the FW. ACS can ping both FW's and vice versa. [code]
Whether ISE-3315-K9 with ise version: Service Engine: 1.0.4.573 , supports the command level accounting Bascially , we have integrated Cisco Switches with Cisco ISE for Device Authentication using Radius , we are able get the authentication logs on to the devices , but for any command changes or update done on Cisco devices we are not able to get the command accounting.
We have Cisco ACS 4.2 in our network and the accounting is done for 750-1000 devices and only for level priv-15.If i want to enable accounting for all levels from priv-1 to 15. All commands executed in devices are sent to ACS. Does the ACS can that much sessions from those many devices?Am also planning to configure acs remote agent to store all the accounting history.
I am trying add custom attributes for Juniper Netscreen TACACS+ authentication to a v5.2 ACS. The advice is to add it to the group as follows:
ervice = netscreen { vsys = root privilege = read-write } I know how to add this to a version v4.x ACS
However, I do not know how to apply this to the custom attribiutes to a v5.x ACS?do I add the vsys and privilege attribute seperately or together? What should be the attribute name? netscreen? Should it be mandatory?
I have a problem trying to export logs to the Cisco ACS View from my ACS 4.2In the document [URL] Cisco states that one of the mandatory attributes for export to work is "Network Access Profile Name" under TACACS+ Accounting (under ACS 4.2 System configuration -> Logging settings). Well, I don't have this mandatory attribute listed in ACS under TACACS+ accounting log configuration. I tried to ignore this attribute, but then ACS View complains about null value for the attribute mentioned above.Is this some bug in ACS View or ACS or maybe I simply missing something?
I am currently useing ACS 5.2 and have no problem using Tacacs+ with AD access.
But with Radius it seems I can only get the Local identity store to work, need to do something special to get Radius to work with active directory with Cisco ACS?
I have been trying to get our IPS (ASA-SSM-10 and 4260) to authenticate with Cisco Radius ACS 5.2 and they are not working. However, I was able to get them working with Microsoft Radius. Below is the logs from the IPS:
I need to configure RADIUS VSA configuration for a my alvarion device. Following are the attributes that need to be configured.
- Packet Data Flow ID (ID 1, integer16) - Direction (ID 4, integer8) - Transport Type (ID 6, integer8) - UplinkQoSID (ID 7, integer8) - DownlinkQoSID (ID 8, integer8)
[code]....
I was able to configure the first 6 attributes, how can I add the Sub - TLV's ClassifiedID, Priority, VLAN-ID and Classifier Direction which come under Classifier. Don't see any option for that in ACS 5.x
We have 2 ACS 4.2.1 servers in Windows 2003 with SP2 installed. We have updated the first ACS to the latest patches for Windows. After that we started having problems. CSRadius either stops by itself or when some time passes we get the following error in Failed attempts "Unknown error". When we restart the ACS services by the GUI, it resumes until the next time it stops.Do you happen to know if we have any bugs related to Windows patches?
I am trying to configure AAA authentication and authorization with Cisco 3725 (IOS 12.4(17)) for 802.1x and ACS 4.2 with VLAN assignment to my Windows XP client. (trying to assign VLAN 100 in my scenario).When user connects to the Router, it passes the authentication process (EAP-MD5). In my debug i see that Router recieves the Radius Attributes BUT does not apply anything!My running config:
Building configuration... Current configuration : 1736 bytes ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec
[code]......
As a result the vlan-switch data based does not change.
