Cisco Firewall :: ASA 5505 PPPoE No Internet?
Jun 18, 2012
We currently use a linux software based firewall called IPCop that sits between our network and router (This is in bridged mode) IPCop conects over PPPoE and everything works fine.
However the system is not reliable and I fear not that secure so have purchased an ASA5505 now I have added the PPPoE info to the device using the ADSM software however although it picks up my external static IP I'm unable to access the internet. On IPCop I only had to enter the broadband credentials and it worked however I feel like I may have to add more to the Cisco, for example do I have to specify DNS servers and do I have to set a static route?
Here is my config file so far (Note I think I have turned on the ability to ping from internal to external). My config I have done through the ADSM as opposed to the CLI
: Saved:ASA Version 8.4(3) !hostname ciscoasaenable password 8Ry2YjIyt7RRXU24 encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface
[Code].....
View 17 Replies
ADVERTISEMENT
Mar 1, 2012
I am tyring to remotely diagnose a troublesome ASA5505
It is connecting via PPPOE and the original suscpicion was that the PPPOE was going down during heavy loads during the day, i.e 9am and lunchtime. I suspected MTU and have verified the MTU outside is set to 1492
However further troubleshooting doing a remote ping to the PPPOE address indicates that this does not drop at all.
When remoteley connected to the ASA my session dies and any outbound internet fails, then in a few minutes it comes back.
all the time the PPPOE line stays up?
One thought is that although the line does not go down it is being crippled with traffic and just getting so unresponsive it appears it has died.
View 2 Replies
View Related
Feb 23, 2011
configure my ASA 5505. It is setup using PPPoE. What I want to do is this:
I have one of my IP addresses (99.23.119.78) setup for ftp using the ftp protocol to our internal IP address 192.168.1.3. What I need is to also allow for HTTP access but not just that, I need it to forward the http port to port 9000 because the web interface requires port 9000 for customer access. Previously on our old firewall customers were able to access the web interface by browsing to [URL]. I would like to not have to not require the port in the URL.
In addition, I would like to be able to setup a different IP address in our range (99.23.119.73) to be setup for http access using the standard port 80 for the same internal IP address (192.168.1.3). This URL will allow us to access the administration web interface for the FTP server.
Here is my current config:
Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasaenable password qVQaNBP31RadYDLM encryptedpasswd 2KFQnbNIdI.2KYOU
[Code].....
View 4 Replies
View Related
Mar 3, 2013
I need to use a Cisco ASA 5505 on a BT Openreach connection, The configs that I have ben using are below -
interface vlan2
nameif outside
security-level 0
[Code]....
View 1 Replies
View Related
Mar 12, 2013
I've an ASA 5505 connecting to a vdsl modem. The ASA is doing the PPPoE encapsulation. I've noticed the traffic amount on the outside interface is always twice the bandwidth it receives on its inside interface. I can't believe the PPP encapsulation is taking that much. Only two interfaces (inside and outside)
View 4 Replies
View Related
Apr 27, 2011
I am using ASA 5505 with firmware 8.2(2). My ISP uses PPPoE as a WAN connection protocol. There is a problem with getting PPPoE session started on my ASA 5505. The debug output says that after negotiation of PPP-authentication protocol ASA receives a PADT packet from ISP’s concentrator. To get more information I captured all packets on outside interface with WireShark. Packet-dumps (in .pcap format) are attached in this post. I have tried all possible combinations of PAP/CHAP/MSCHAP values in “vpdn group MYGROUP ppp authentication” command. If you take a look at the packet-dumps you can see, that in case of “PAP” – ISP’s concentrator rejects negotiation (PAP is not supported by my ISP). In case of CHAP/MSCHAP (that ARE supported by my ISP) – ASA acknowledges the using of MSCHAP v.2 PPP-auth protocol, which is actually not supported by it…
Judging by MAC-addresses of ISP’s concentrators it is visible that Cisco’s equipment also is used.
The questions is: Why ASA acknowledges using of unsupported ppp-auth protocol during negotiation and what I need to do to resolve this issue? (ISP’s support says, that they cannot change PPP-auth protocol negotiation order. Also they says that I need to contact with manufacturer of my equipment).
View 3 Replies
View Related
Jan 25, 2011
I've been having this issue for about 3 months now, off and on, never seemed to be predictable but started happening more and more, which prompted me to look into it.
Currently, the DSL Modem is configured in bridge mode with the ASA handling PPPoE. The WAN address is being assigned via DHCP. The ASA is running 8.2(1). The WAN interface will drop it's DHCP lease and will not renew it without power cycling the DSL modem. I did a little bit of googling and found mention of setting "dhcp-client client-id interface outside", specifically this was an issue pre 7.2(22), but doesn't seem to affect my situation. Originally, I had the MTU on the outside interface configured as 1500, changing it to 1492 has not resolved my issue either.
I've enabled PPPoE and DHCPC debugging and posted the results below when the event occurs, I'm thinking this is moreso a PPPoE issue than it is a DHCP/DHCP Lease issue as I am not seeing any debug messages from DHCPC.
Code...
View 1 Replies
View Related
Apr 25, 2013
I just bought a 5505 to learn from and am trying to attach my VDSL modem as a transparent bridge.It goes....
Laptop >>> (VLAN1) Cisco 5505 (VLAN2) >>> VDSL modem >>> internet
X.X.X.10 >>> (X.X.X.254) ------ (Y.Y.Y.254) >>> Y.Y.Y.10 >>> A.B.C.D.
I'm using the ASDM, if I configure VLAN2 with the IP address of the VDSL interface I can ping the modem from the console session via Putty. If I take that off and configure up the PPPOE client I can't ping the VDSL modem, I'd expect that. If I then add in an IP address to the PPPOE client config like I assigned to VLAN2 it doesn't ping either.If I can't ping the VDSL modem I don't expect it would work but it seems I can only either give it a static address which pings but has no pppoe or give it a PPPOE config which means I can't ping the VDSL. why I can't ping the VDSL modem when the interface is set as PPPOE with an IP address?Presumably if I'm on the ASA console doing pings from there to the modem then I'm ruling out problems with the routing from the laptop (trying to isolate where the issue is)
View 3 Replies
View Related
Aug 23, 2011
setting up an ASA 5505 to be used as a firewall between a BT internet router(BTNet service) and a Cisco 3560 Lan switch. BT have presented me with a cisco 3800 series router with the following details:
Network Address Network Mask BTnet NTE Router LAN Address
There are 2 Gigethernet ports on the back of the router port Ge0/0 is connected to the BT NTE and the status light is flashing green. Int ge0/1 is connected into port int e0/1 of the ASA but i am unable to get any connection.
View 21 Replies
View Related
Apr 1, 2013
I am trying to configure DMZ on ASA 5505, basic license. After changes I have made I cannot access Internet from DMZ. I think I am missing an access list for DMZ, but I am not sure.
interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1 !interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5switchport access vlan 3!interface Ethernet0/6!interface
[Code].....
View 4 Replies
View Related
Jun 2, 2011
I have basically started fresh, from a clean image. We bought these with the expectation that we would be able to configure them using the GUI for what we need, which up till this point doesn’t seem to be the case.I will tell you how I have this setup, I have our ADSL going to a modem acting as a bridge with a static IP supplied by the ISP. If i connect a laptop to that modem and set the static ip on the laptop, I get internet access fine.So I then connect the modem to ethernet0/0 and the laptop to ethernet 0/1 I connect to the ASDM and run the startup wizard with the following:
· Outside ip : 87.87.87.87 255.255.252.0 (this works on the lappy straight to the modem)
· Inside ip : 192.168.10.1 255.255.255.0
· No dmz
[code]......
View 2 Replies
View Related
Dec 27, 2011
First time attempting to set up a 5505. Trying to replace a snapgear firewall and replicate the settings to the 5505.
View 12 Replies
View Related
Sep 6, 2011
I have a 5505 ver 8.2 connected to a router with a T1 internet connection. There was a problem with the internet service and when it was resolved the ASA did not pass traffic to the internet until it was power-cycled. Unfortunately that's all the info I have, as I was not onsite and couldn't access the ASA.
View 3 Replies
View Related
Dec 11, 2012
I am using ASA 5505.Below are my sh run.I am not able to ping my gatway i.e 182.73.131.89
interface Ethernet0/0
description Internet Interface
switchport access vlan 61
!
interface Ethernet0/1
description office Internet
switchport access vlan 50
[code]....
View 3 Replies
View Related
Apr 1, 2013
I have not been having much success configuring my 5505 for Internet access, and I'm sure there are a few small things I'm missing. At times I believe I got it to the point where I could ping, but still not pass through the Internet traffic. At this point, I reset the 5505 and only changed a couple of settings. I have an external range with these characteristics: Network Address 67.139.113.16 (.17 is Gateway), SM: 255.255.255.248, available IP: 67.139.113.218 The external connection is through a T1 modem, and when I put those settings in my laptop, I can access just fine. When I went through the startup wizard in the ADSM, I maded the internal interface 10.209.0.3, subnet mask: 255.255.255.0 I selected PAT in the Wizard, but don't know if I should have, or if the NAT rules I tried to put in are fine. Eventually I want to add a Site to Site VPN to the rest of the 10.0.0.0 network, but I can't even pass the Internet through to the inside. Also, this will eventually be behind another hosted firewall, so I'm not worried about restricting access, even currently. However, I suspect the problem is that traffic is being blocked with the NAT rules or Access rules.I wish I could just disable those inherent deny rules Outside of pings to 10.209.0.3, all pings come back as request timed out.
Config:
: Saved
:
ASA Version 8.2(5)
!
[Code].....
View 16 Replies
View Related
Jun 17, 2012
I am trying to configure Nat on a clean ASA 5505, but can't get it to work. I ran the commands below. On the ASA I can ping the internet and inside vlan ip. On my laptop I can ping the ASA inside vlan ip, but I can't ping the outside vlan ip. From another network I can ping the ASA outside public ip. Is there an access-list that denies inside from accessing outside?
I am running version 8.4(3) and I erased the existing configuration.
ASA(config)# interface vlan 1
ASA(config-if)# ip address 10.0.0.1 255.255.255.0
ASA(config-if)# nameif inside
[Code].....
View 8 Replies
View Related
Dec 4, 2012
I want to access my ASA 5505 from internet.how I can achieve it.
View 1 Replies
View Related
Aug 31, 2012
I have an ASA 5505 behind my internet router. i have got only one public ip configured on the router outside interface.192.168.20.0/24 subnet is configured between ASA and router and inside network is 192.168.10.0/24 (Refer the attached diagram).
I have exposed my mail server and ftp server to public through static PAT in router and ASA with the same public on router outside interface. Iam facing issue some of the machines inside my network internet is not working(actually DNS is not resolving) some of the PC's internet is working fine some of the PC's randomly working. i have attached the diagram and ASA config , after this issue is sorted out i need to configure a L2L VPN to my head office.
View 8 Replies
View Related
Aug 11, 2012
I have a Cisco ASA 5505 that has been configured to act as a router as well. I have configured 3 VLANS that have access to the internet. For some reason the "InsideWifi" and the "Guest" VLANS have very slow internet speeds and sometime web pages wont finish loading properly. The "Inside" VLAN gets the speeds that are expected. The DNS server does reside on the "Inside" VLAN. Is there anything wrong with my configuration that would cause the internet speeds on the other VLANS to be slow? My config is attached.
View 6 Replies
View Related
May 24, 2011
I'm trying to allow SSH traffic from the Internet to my DMZ. I gave my remote guy my ip and he can see the ASA 5505 but not get into the DMZ. The outside is 70.165.19.137. The DMZ server is 192.168.60.2. I have the inside talking to the DMZ fine. [code]
View 9 Replies
View Related
Aug 9, 2012
I recently bought an ASA on eBay the plan was to try and learn how to configure them and get more familar with Cisco's ASA hardware etc.
I want it to do the routing for my home network. The way things are setup at the moment is pretty standard. I have an ADSL modem which is also a router which was provided by my ISP (Orange).
The first thing I did was change the router to be in "modem only" mode which seems to have worked. I then got the ASA to use PPPOE by following this guide [URL] I assume that worked as it is authenticating with the ISP and I'm getting a puplic IP address assigned to the outside interface. The default gateway is being set by the "ip address pppoe set route" command which I have verified with the "show route" command. The problem I'm having is that even though I'm getting a public IP I can't ping any thing from the ASA I've pinged 8.8.8.8 and 4.4.4.2 using the outside interface as the source but I'm not getting any responce. I have tried changing the MTU a few times to different amounts on the outside interface with no luck.
View 10 Replies
View Related
Feb 27, 2011
I set up an ASA 5505 at home through PPPOE connection. The ASA seems to obtain an IP address correctly.and I can ping a public ip address using the outside nic, but not the inside nic. I saw the error message when I ping: No route to ff0213 from fe801bc2b1288cd5bc1. As a result, I cannot connect to the Internet.
View 11 Replies
View Related
Oct 10, 2012
I would like know is that possible to connect two 5505 ASA in site to site VPN with 1 site using ADSL pppoe connection?
View 5 Replies
View Related
Feb 5, 2012
I'm trying to configure a second server on my network but whenever I add the static NAT rule, the internet stops working on that computer.
Here's my Cisco ASA configuration:
ASA Version 7.2(3)
!
hostname domain
[Code].....
View 16 Replies
View Related
Sep 27, 2012
I have config ASA 5505 and it is conencted to layer 3 switch that connects to cable Modem.
ASA is config with DHCP option and PC is able to get the IP from ASA. But from PC i am unable to access the internet. From ASA itself i am able to ping the Websites fine.
ASA has config with DHCP for inside and also it is doing NAT.
When i connect the ASA directly to Cable modem then pc is able to access the internet.
View 4 Replies
View Related
Apr 5, 2013
I have setup 5505 ASA for Testing purposes. It has static route to layer 3 switch on outside interface that goes to the internet.
ciscoasa# sh route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
[Code].....
View 20 Replies
View Related
Jul 5, 2011
I would like to restrict Internet traffic (HTTP & HTTPS) for Inside Users with an ASA 5505. I would like to setup a proxy-like system where a User/Password must be entered before the User can actually browse the web.
I know that this can be done with an additional RADIUS/TACACS+ Server. Is this also possible without any external AAA Server, so with User/PW stored on the ASA locally only?
View 1 Replies
View Related
Jul 20, 2011
I have configured the ASA 5505 for internet access and outside users to use two servers in the DMZ. Every thing is working fine. When I was configure VPN, I did some mistake I guess, now inside users are not able to access internet. They get an error 405. Thats an error. The request method XXX is inappropriate for the URL /. Thats all we know. Even I am not able to access the server in the DMZ from outside and I get an error : Bad Request - Invalid HeaderThese things just happend after I did some thing on the ASA. I copy and pasted the my old configuration but still insider users are not able to connect to internet and from outside I am not ableto connect to server. The weired thing is that I can user VPN with out any issues. I can connect to vpn but I cant access any internal resources. Even inside users are able to ping internet addresses with out any issue.
View 2 Replies
View Related
Feb 27, 2011
I changed a configuration and suddenly I lost the internet connectivity... Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasaenable password qVQaNBP31RadYDLM encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 !interface Vlan2 nameif ATT security-level 0 pppoe client vpdn group ATT ip address pppoe setroute !interface Ethernet0/0 switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!ftp mode passiveclock timezone EST -5clock summer-time EDT recurringsame-security-traffic permit inter-interfaceobject-group service DM_INLINE_TCP_1 tcp port-object eq ftp port-object eq ftp-data port-object eq wwwaccess-list ATT_access_in remark Linkstation Accessaccess-list ATT_access_in extended permit tcp any host 99.23.119.78 object-group DM_INLINE_TCP_1 access-list ATT_access_in remark Linkstation
[code]....
View 3 Replies
View Related
Jun 28, 2011
I found a tricky task for our ASA 5505 firewall. I am not able to go internet when using DHCP but I can access by using fixed IP address in client PC.Same IP, Same Mask, Same DNS, Same Gateway. All the same but no hope. Any configuration i missed in firewall?
View 5 Replies
View Related
Mar 8, 2011
I'm unable to have any internet connection for my new setup.
here's the overview.
Current setup is
Internet -> Router -> PIX 501 -> Switch -> clients
Internet -> static ip given is 210.193.34.1 - 210.193.34.6
Router -> Static ip assigned for NAT/External is 210.193.34.1, Local ip is 192.168.1.246
PIX 501 setting ->
IP to Router, According to router screen is 210.193.34.2, but not sure what settings are done in the PIX itself as I'm unable to access it.
local ip is 192.168.1.1
Clients - > 192.168.1.0
Old setup is working fine and connected to internet. for the new setup, as i do not want any downtime for the old setup.
As you can see, there are two firewalls connected concurrently to the router. I've configured it this way.
Internet -> Router -> ASA 5505 -> Switch -> clients
ASA 5505 setting ->
IP to Router NAT/External/ Outside Interface, 210.193.34.6 (Or do i set as 192.168.1.0?),
local ip/ Inside Interface is 192.168.2.1
Clients - > 192.168.2.0
some setup details.
security policy, NAT, set to default. routing is route outside 0.0.0.0 0.0.0.0 210193.34.6
I'm unable to access after a week of troubleshooting.
View 7 Replies
View Related
Oct 10, 2012
i am looking for the best practices when using a Cisco ASA 5505 to provide NAT and protect my inside network from the outside.
I have the inside security level set to 100 and the outside set to 0, want other features can be used to protect the network from the Internet, am assuming that the security levels will ensure no traffic comes from the outside to the inside unless there is a rule that allows it.
Would any firewall policies be required to increase the level of security?
View 1 Replies
View Related
Jul 30, 2011
I have a ASA 5505. I want to be able to ping from my workstation to some address, lets say [URL]. My workstation is connected to Ethernet 0/2. I have tried playing around with the ACL but am not able to accomplish this.
Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasadomain-name home.7vnmotorsports.com
[Code]....
View 5 Replies
View Related
