Cisco Firewall :: ASA 5540 Blocking Legit Traffic From Inside
Aug 21, 2011
I just made a move from a PIX 506 to an ASA 5540. I have a user that currently logs into a web portal and runs a job. It is now erroring out. When I run the test it gives me the following message:
Testing ports...
Port 1433: Failed
Port 1150: Success
Port 80: Success
Port 443: Success
One or more tests have failed
The computer we access this site from is on the inside network and the ACL says permit ip any any from the inside out so I am not sure why it is failing. Under the ASA Home screen I see the Top 10 Protected Servers under SYN Attack and it appears that the ASA thinks this is some sort of attack.
View 1 Replies
ADVERTISEMENT
Jan 7, 2012
Previous attempts to set up these NAT rules has been met with minimal success. We have been able to get the NAT rules created, and able to ping our inside servers and receivers from a different outside network, but every time we get that far our internal network crashes. Running the Packet Trace utility via the ASDM shows that internal traffic from the servers to the workstations is being blocked by the default implicit rule under the access rule heading that states "any to any, service being ip, action= deny". Reverse traffic from the workstations to the servers is being allowed though. In an effort to start over again, the Cisco ASA has been Factory Defaulted via the CLI, and has had it's Inside network, and Outside IP address set back up. DHCP pool has been setup for a minimal amount of addresses on the inside network, since most of our equipment will always be assigned statics. We reset our static NAT policies, and seem to be having the same problem. My partner and I have been working on this for some time now, and have ourselves so frustrated that I know we are missing something simple. [code]
View 10 Replies
View Related
Dec 20, 2012
i am using asa5540 with 7.0(8). firewall was configured in transparent mode.
now i am looking for block ip phone communication from site to site and head office. i am using cucm 7.1.2b.
all site was connected through ofc. no nat was using.
View 1 Replies
View Related
Sep 27, 2012
ASA 5540 8.2 (5)I have tried many combinations of command line syntax suggested in this forum but none are providing success so far.
I want to ping from the Inside Interface across to the Outside Interface and visa versa.I have tried various ACLs as well as "inspect icmp" in the config, etc still no go.
I can ping each interface from the console command line but cannot ping across each interface. [code]
View 1 Replies
View Related
Mar 24, 2013
We have an ASA 5540 with 8.2(5)
Last three days in early afternoon we start getting these errors in the log and webpages either won't load or pages only half load.
3|Mar 22 2013|13:22:24|305006|184.73.105.115|443|||portmap translation creation failed for tcp src inside:10.10.176.114/58217 dst outside:184.73.105.115/443
3|Mar 22 2013|13:22:24|305006|54.243.129.71|80|||portmap translation creation failed for tcp src inside:10.35.54.37/1517 dst outside:54.243.129.71/80
[Code].....
View 6 Replies
View Related
Feb 15, 2013
networking but can understand with a bit of explanation.. I own a restaurant and provide free WiFi for my customers with a Cisco E2500, I am gettign bills that are through the roof, I contacted my ISP and was told users were accessing P2P downloads(uTorrent, etc.). How can I block these applications?
View 1 Replies
View Related
Oct 14, 2012
I have a LAN with several linux boxes (Fedora 17, both 32 and 64 bits), as well a a WInXP box. All of these are connected to the same switch, which is connected to the inside port of my PIX 515.
For a few sites (mozilla.org happens to be one of them), for http access, the tcp connection is established, but the "GET" request - or anything else for that matter - will not go through the PIX (from inside to wan). I have verified this by first, using wireshark to watch the packets being sent out from the client box, then by using the trace function in the PIX to see that the packets ARE arriving at the inside interface, but ARE NOT sent out of the wan interface.
This is for the linux boxes ONLY. When I do the same thing with my WinXP box, all works: in the PIX trace, I see the packets arrive at the inside interface, and leave the wan interace. And access to these sites are okay.
(What's a bit weird, although somewhat expected, when I connect my android phone to my LAN via WiFi, it too is unable to reach those sites - but then again, android is linux, right?)
In addition to the tracing, I have narrowed this problem down by connecting a linux box directly to my DSL router, then replacing the PIX with a simple router/gateway. Both of those solutions work.
Some background:
I have been using this PIX for about 10 years now, with the same configuration (except IP addresses). Only in the last several months has this problem started to show up.
I got this pix from a dead company at a really great price (free), so I'd like to keep it, and not have to spend money on something else. I don't have any support license, and have not been able to get any software upgrades. Here is its version info:
taz(config)# sho ver
Cisco PIX Firewall Version 6.2(2)
Cisco PIX Device Manager Version 2.0(2)
Compiled on Fri 07-Jun-02 17:49 by (code)
Serial Number: 405200362 (0x1826ddea)
Running Activation Key: 0x38ac31f3 0x0630df47 0x9a77b805 0x8bc39a60
PS: Since this PIX is at its end of life, I was wondering if any of the software upgrades would be now available without a license?
View 2 Replies
View Related
Apr 22, 2013
OK, I have a 2921 on 15.3-2T. ZBFW is working from the inside to the outside, but the DMZ is not being blocked at all to the inside. I am currently running with subinterfaces. All interfaces have zones attached. I have policies from inside to outside and DMZ to outside, those work fine. Without any policy from DMZ to inside, it can pass traffic freely from DMZ to inside. I have tried making an explicit policy to drop all to inside, still passes. I ended up just having to put an ACL on the interface
I already tried upgrading the IOS, that is how I ended up on the newest version. This is connected to a 2960S with a trunk port. Everything else works perfectly except for the DMZ security. I haven't had time to try to lab it up yet, but wanted to see if any reasons this shouldn't work, as all documentation says it should drop all traffic unless you make a policy to pass traffic.
View 5 Replies
View Related
May 31, 2012
This has to be the most weirdest issue I have seen since the past year on my ASA. I have an ASA 5540 running the 8.4(2) code without any issues until I stumbled upon this problem last week and I have spent sleepless nights with no resolution! So, take a deep breath and here is a brief description of my setup and the problem:
A Simple IPSEC tunnel between my ASA 5540 8.4(2) and a Juniper SSG 140 screen OS 6.3.0r9.0(route based VPN)
The tunnel comes up without any issues but the ASA refuses to encrypt the traffic but decrypts it with GLORY! below are some debug outputs, show outputs and a packet tracer output which also has an explanation of my WEIRD NAT issue:
My setup - ( I wont get into the tunnel encryption details as my tunnel negotiations are **** perfect and comes up right off the bat when the ASA is configured as answer only)
CISCO ASA - IPSec networking details
LOCAL NETWORK - 10.2.4.0/28
REMOTE NETWORK - 192.168.171.8/32
JUNIPER SSG 140 - IPSec networking details
PROXY ID: LOCAL NETWORK - 192.168.171.8/32
REMOTE NETWORK - 10.2.4.0/28
HOST NAME# sh cry ipsec sa peer <JUNIPER SSG PEER>
peer address: <JUNIPER SSG PEER>
[code]...
As you can see, there is no echo reply packet at all as the packet is not being encapsulated while it is being sent back. I have been going mad with this. Also, this is a live production multi tenant firewall with no issues at all apart from this ****** ip sec tunnel to a juniper!!
Also, the 192.168.10.0/24 is another IP Sec tunnel remote network to this 10.2.4.0/28 network and this IP SEC tunnel has a similar Juniper SSG 140 screen os 6.3.0r9.0 at the remote end and this woks like a charm without any issues, but the 171 is not being encrypted by the ASA at all.
View 2 Replies
View Related
Oct 25, 2012
I have a cisco ASA5505, it runs a wide site to site VPN network and has 4 servers connected to it
10.50.15.4 > fileserver
10.50.15.5 > domain controller (exchange)
10.50.15.6 > terminal server
10.50.15.7 > terminal server
Now yesterday i removed 10.50.15.6 and replaced it with a new terminal server with the same ip address, ever since the ASA is blocking traffic between it and the domain controller (example)
2Oct 27 201214:51:0510600710.50.15.655978DNSDeny inbound UDP from 10.50.15.6/55978 to 10.50.15.5/53 due to DNS Query What has me baffled is the only thing different between today and yesterday is the new server is windows server 2008 and the old one was windows server 2003. The new server has the same LAN ip address as the old one to make the changeover seamless for the users.
why all the sudden my ASA has decided to block the traffic between those machines? all the other machines can talk to it fine just not the domain controller, and seeing that this is a terminal server naturally you can see the problem i face!
this router has worked flawlessly for 2 years now without any config changes and i cant work out why its blocking traffic between those 2 machines.
View 15 Replies
View Related
Apr 5, 2013
I have a RV110W that's been in service since Dec 2012. All Everything is working fine except every month or so the firewall starts blocking all inbound traffic. It does not respond to remote management access. If I reboot the firewall (pwr off/on) everything works correctly for the next month or so and then it begins blocking all inbound traffic again. Local access to the Internet and VPN tunneling are not affected. When it's working, all my rules and port forwarding work correctly.
View 2 Replies
View Related
Apr 2, 2012
My internet link is connected on Internet Router & below downwards Cisco ASA 5520 is connected.ASA is connected with core switch cisco 4510 on downwards. our web based mail [URL] is hosted outside.
Lets suppose ISP pool is 4.4.4.0/28.suppose owa server is Static natted on ASA with 4.4.4.4. my machine traffic is going to internet with same ISP with PAT on Cisco ASA & internet is working on my machine. if i want to access {URL} or ip base for mail access, its not working & also it is not pinging. i suppose to ASA is blocking for returning traffic.
is there any way to traffic will go via same Firewall & comeback on same firewall port?
View 1 Replies
View Related
Apr 18, 2012
I have a 1921 K9 with a 4 port 10/100/1000 EHWIC switch.
Interface 0/1 = 192.168.1.0
EHWIC = 192.168.5.0
I have Active Directory setup on the 192.168.1.0 network. When I attempt to join the domain from 192.168.5.0 it joins but I get errors. After some troubleshooting using portqry I have found that the services related to class map DomainTrafficUDP are being reported by portqry as being filtered regardless of policy map settings (currently set to allow).
Building configuration...
Current configuration : 18833 bytes
!
! Last configuration change at 11:20:25 NewYork Thu Apr 19 2012 by dave
! NVRAM config last updated at 13:56:45 NewYork Wed Apr 18 2012 by dave
!
[Code].....
View 2 Replies
View Related
Dec 25, 2012
Most examples of NAT translation using an ASA 8.4 are based on servers within a DMZ. In my case it's not because the mailserver also functions as an data and Active Directory server for my local domain. If tried to config the ASA for a while now and throw it in the corner for a couple of months out of frustration. Now I got some time left during christmas break I decided to start again.My purpose is to NAT SMTP / POP traffic from the internet, trough the ASA to my (inside) server. This is what I got so far. With this config I'm unable to telnet the inside server (192.168.1.10) from a remote location.
ASA Version 8.4(3)!hostname ciscoasaenable password cE8UUNd encryptedpasswd 2KFQ.2KYOU encryptednames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.253 255.255.255.0!interface Vlan2nameif outsidesecurity-level 0ip address 95.*.*.218 255.255.255.248!ftp mode passiveobject network obj_anysubnet 0.0.0.0 0.0.0.0object network server1_smtphost 192.168.1.10object network server1_pop3host 192.168.1.10access-list outside_access_in extended
[code]....
I can ping 192.168.1.10 from the ASA CLI. I can Ping DNS 4.2.2.2 from the CLI (internet access). I can Telnet the server from the inside LAN, using: telnet 192.168.1.10 25.But I can't Telnet from an outside location using: Telnet 95.*.*.218 25 Because my server is on the Inside interface (diffenrent subnet) do I need an additional route?
View 5 Replies
View Related
Mar 2, 2011
I am setting up a pair of 5520 in A/S mode but the traffic from inside to outside seems blocked somehow.
asa01# sh run : Saved
ASA Version 8.3(1)
host name asa01
enable password LFJ8dTG1HExu/pWQ encrypted
password 2KFQnbNIdI.2KYOU encrypted
names
[code]......
Base on the above configuration, I still cannot ping or HTTP.
View 10 Replies
View Related
Nov 18, 2011
One Host on inside network needs to access customized application hosted on Internet. Its a customized application run on port 80, 443, 5000-to-50020
How do I allow this host access for this specific application. I got ASA 5510 and host is in the inside network, we also got an ACL on inside interface to have control.
-Host IP on inside network - 172.16.30.15
-Application to access - 74.219.x.x
-Inside ACL name - inside-acl
View 5 Replies
View Related
Nov 26, 2012
I am attempting to block outbound traffic for a specific PC on my LAN using the ASDM.
View 2 Replies
View Related
May 15, 2012
Let me start by saying that I'm just starting to study for CCNA, so the ASA seems to be a bit above me yet. The ASA's we are using is for VPN to our corporate office and only allowing access to our Citrix environment, so no direct internet allowed. We have a person who works in the remote office who has need for a caption telephone that requires direct access to the internet. The phone only supports DHCP, and getting the ASA to do an ARP reservations is proving difficult. For now I wrote an access list to allow it's DHCP address out but it still isn't working. The access list I wrote is:
access-list 101 extended permit ip host xxx.xxx.xxx.124 any log
access-list 101 extended permit ip any any
access-group 101 out interface outside
When I do a show access-list I'm seeing that traffic is hitting the access list as the hit counter has increased. When I do a show conn I'm seeing one of the IP's that the phone should have access to, however the flags are: saA, so I'm assuming they are not getting a response. According to the manufacturer, only outbound connections are needed, no incoming ports required. All traffic is TCP.
View 8 Replies
View Related
Nov 28, 2011
Quick question. I have a site - site tunnel that is up and running between a Pix 515E and a 3050 appliance.Tunnel is up and running but on the pix side I dont see traffic from a couple of subnets behind the inside interface.On the vpnallow access list there are no hits So I setup a capture on the inside interface to see if the packets is making it to the inside interface and nothing. There is some traffic making it thru the tunnel that would have to hit the inside int first and even that doesnt showup in the capture.
View 1 Replies
View Related
Nov 27, 2011
I am trying to make a basic config on my 5520. The first goal is to make trafic from inside to outside.The internet address is 64.28.29.200 and the default internet gw is 64.28.20.193What am I missing since I can not get trafic from inside to the internet? [code]
View 10 Replies
View Related
Nov 9, 2011
I trying to allow traffic between 2 inside interfaces with the same security level. VLAN1 and VLAN15. The are on different physical ports on the ASA. I tried to configure this through the GUI Web interface and checked ' enable traffic between two or more interfaces with the same security levels'. With this ASA version, I do not need NAT to allow this, correct?
ASA Version 8.2(1)
!
hostname ciscoasa
[Code].....
View 1 Replies
View Related
Oct 13, 2012
I need to configure a Cisco ASA5510.Connencted the a single interface I have a switch. To this switch (same VLAN) there are connected:
1. The Subnet of the main office (192.168.1.253)
2. A router (IP 192.168.1.254) that routes the traffic to a remote location (Subnet 192.168.8.0/24)
I have so allowed any traffic incoming to the inside interface as follows:access-list inside_access_in extended permit ip any any and I have permitted traffic intra interface as follows: same-security-traffic permit intra-interface. [code]Unfortunately I cannot RDP into that server. When I simulate the connection via Packet tracer, it tells me that the implicit deny on the bottom of the connections from "inside" (firewall) does not allow the connection. It sounds to me like that "same-security-traffic permit intra-interface" does work only if there are 2 interfaces and not a single one.Unfortunately I cannot just unplug the cable and connect it into another port as the ip is on the same subnet and I cannot configure the other end router.
View 4 Replies
View Related
Jul 21, 2012
We have a Cisco ASA 5505 (v7.2(3)) with a "fairly" normal configuration yet we have a problem where it appears UDP/53 traffic is denied on our inside network.
here is output from our sys log:
SyslogID Source IP Dest IP Description
305006 172.18.22.3 portmap translation creation failed for udp src inside:172.18.22.156/42013 dst inside:172.18.22.3/53
To give some clarification:
172.18.22.3 is one of our DNS servers
172.18.22.156 is a device we're experimenting with.
We've bypassed the Cisco by using a 4G wireless router with this same device - and it works flawlessly.Here is a [scrubbed] copy of our config. It is what I inherited from the previous admin - I'm not sure of all its finer points (I'm not Cisco certified -- perhaps I'm just certifiable.)
: Saved
:
ASA Version 7.2(3)
!
hostname [redacted]
[code].....
View 5 Replies
View Related
Apr 6, 2011
I have a handheld device that will be used for inventory outside of our office. It has 3g capabilities. Is there anyway I can permit traffic from this device from the outside world coming into my network? I need to open a couple of ports so it can hit the server. But I have no intention to open these ports up to the entire world. I use an ASA 5520 with a managed router from our provider. I looked around on the Cisco site and the only information I found was for permitting and denying traffic from devices that are within the network.
View 2 Replies
View Related
Oct 10, 2011
I've been trying to figure this one out for quite a while. I currently have 2 inside interfaces (data, phone) and I am moving to 3 inside interfaces (servers, workstations, phones). I have not been able to get any traffic between the interfaces. With the current setup it was not a major problem. With the new setup it will be a major problem.
Below is a sanitized version of the config.
ASA Version 8.2(1)
!
hostname BOB
[Code].....
View 11 Replies
View Related
Mar 12, 2013
I've an ASA 5505 connecting to a vdsl modem. The ASA is doing the PPPoE encapsulation. I've noticed the traffic amount on the outside interface is always twice the bandwidth it receives on its inside interface. I can't believe the PPP encapsulation is taking that much. Only two interfaces (inside and outside)
View 4 Replies
View Related
May 5, 2011
I have a ASA 5540+SSM-40 on which I have configured webvpn and it's listening for connections on the outside interface. It can be accessed from outside the network (the internet) and works just fine. The problem is, I want to access it from inside the network as well but it doesn't work. I can't ping or connect in any way to the IP address of the outside interface from inside (so I suppose it's not strictly related to the configuration of the webvpn).
I don't think it's a ACL issue because the only ACL filtering I do is on the OUTSIDE-IN (facing the internet), the rest are set to permit any.
What I have to do to be able to access the IP address of the outside interface from networks behind the inside interface?
View 5 Replies
View Related
Apr 19, 2012
I got ASA 5510 with base license, can I block all Peer-2-Peer traffic from inside to outside.
ASA Giga 0/0 connected to ISP Router 2811
ASA Giga 0/1 connected to LAN switch 3560
View 3 Replies
View Related
Oct 9, 2011
I have Pix 501 firewall and I'm just configuring the device for "Email Server" to allowing POP/SMTP.
Inside Interface Address: 132.147.162.14/255.255.0.0
Outside Interface Address: ISP provided IP address
My question is can my traffic goes from inside interface to outside interface? (because the inside interface address not from 10.0/172./192.168 private address)Also I'm allowing internet from this email server (132.147.162.14) so what my access list to be configured? and what my subnet mask shoud be there?
Pix(config)#access-list outbound permit tcp 132.147.162.14 255.255.0.0 any eq 80
Pix(config)#access-list outbound permit udp 132.147.162.14 255.255.0.0 any eq 53
Pix(config)#access-group outbound in interface inside
View 7 Replies
View Related
Feb 28, 2011
We're running 8.3(2) in the ASA5540. Users all over our enterprise connect to a business partner's application through the ASA/VPN. We have a class-b address space, and since the users are spread out all over the place, I have the entire class-b space as the local object in the ACL that allows traffic through the VPN tunnel.
The business partner has concerns that our entire address space is available to access the VPN tunnel. So I thought, to alleviate their concerns, to PAT all of our connections outbound to a single IP address.
How is this done in 8.3(2)? We use ASDM to configure the 5540. For example, say our class-b is 159.12.0.0 and the PAT'd IP address will be 199.30.36.6.
View 5 Replies
View Related
Mar 26, 2011
URL ,A Netgear WNDR3700 for only $80? Everywhere else I have looked they've been over $100.
View 2 Replies
View Related
May 16, 2012
I have a Cisco 2500 Wireless Controller connected and controlling 5 Cisco AP's. Everything works fine except one device.
This device is used to connect to our AP wirelessly and then any of the wireless laptops can use programming software to connect to the device and program through it. I can successfully set up our device on the network and all PCs can ping it, but the programming software refuses to connect to it. I spent an hour and a half on the phone with the device people who assure me its the network. So, I bought in a cheap Linksys router, hooked one laptop up to it and configured the device wirelessly. With that, the programming software works.
what should I be looking for in the Wireless Controller that may be blocking direct connection to the device even though I can ping it?
View 10 Replies
View Related
Dec 28, 2012
I wonder if I can have a RV042 VPN Tunnel to a RV082, and in the RV082 block all traffic to the internet that comes form the PCs that are behind the RV042.
Remote PC -> RV042 -> VPN -> RV082 -> RV082 Firewall (block internet traffice, allow intranet traffic)
View 3 Replies
View Related
