I need to configure my asa as follows: Two active ISP´s, one(ISP1) for outbound traffic (normal internet traffic) and the other one for inbound traffic(ISP2), http to a web server in the inside network. I have two default routes, one pointing to ISP 1 with metric 1 and the other to ISP2 with metric 2. I perform dynamic nat to ISP1 interface with hosts in the inside network and static nat to ISP2 interface with web server.
View 1 RepliesMy client is transitioning to a new ISP and want to migrate there web servers in stages. therefore they would like to keep some servers running on the old ISP and some servers use the new ISP.
I have set this up in a lab and keep running into routning issues (I am using 5510 for the lab as I do not have a 5505 available). I know that ASA's don't support PBR. Is there any way or trick to get this to work on the ASA?
I have a feeling this is not possible and we would need to get another ASA or a Router to get this to work.
I am attempting to set up failover dual ISP on a 5505 running 8.4(4) with the Sec Plus license. Everything i have been able to reference so far, points to old commands not available or relevant in 8.4
For instance:
global (backup) 1 interface
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 20.20.20.1 1
route backup 0.0.0.0 0.0.0.0 30.30.30.1 10
What is the new syntax that should be used to mimic these commands? I have the sla and trach reachability configuration already set up.
I would like to configure a Cisco ASA 5505 with Dual ISP (ISP 1 and ISP2) and two networks (network 1 and network 2). My customer need that clients in the network 1 connect to Internet with ISP1 and clients in the network 2 connect with ISP2. If a failure occurs in ISP1 (just an example) the network 1 clients connect with ISP2.
View 10 Replies View RelatedI have an ASA5505 with Security Plus license so I can have many interfaces (not 2 + 1 limited DMZ like in base license)
I have 2 VLANs.Is it possible to use one ISP for VLAN 1 and other for VLAN 2 ? Is it limited to 2 ISP's or can have more ?
I have ASA 5505 ver, 8.4(1) I have configured 2 WAN links to
1. Outside1 - distance metric 50
2. Outside2 - distance metric 20
Currentry all traffic is passing thru Outside2 and it's correct, also s2s and ra VPN is also running on Outside2 ?My current case is to use Outside1 for webvpn services only. I can't use Outside2 becouse on 443 port other services are running, also I cant change webvpn port to other.
How can I match packets incoming to interface Internet1 from Interner side nad route them back thru Internet1 interface.
IPSLA is not a good solution becouse I need to have both WAN links used Now in routing table I have only onre record
S* 0.0.0.0 0.0.0.0 [20/0] via x.x.x.x, INTERNET2
for link with lower metric, but after some problems with provider for link Internet2 routing has changed for Internet1 and didn't change it back after resolving problem? how to create it for all traffic incoming for Internet1 interface from outside?
We have a cisco ASA 5505 with sec bundle plus
We have two ISP's:
ISP1 (Our IP = 30.100.150.50, gateway 30.100.150.8)
ISP2 (Our IP = dynamic, gateway 20.100.150.9) - ADSL
Our internal LAN IP range is 10.9.8.0/24
We want to configure the ASA 5505 to allow users via ISP2 for http traffic We then want to use ISP1 for strictly VPN and access to internal web resources (eg OWA) as we have public IP's there.
Our idea was to configure two gateways on the ASA (e.g. 10.9.8.5 via ISP2 and 10.9.8.6 via ISP1)
Then give the users gateway 10.9.8.5 for web browsing etc Is this configuration possible on the ASA 5505?
I have a 5505 configured with a active/standby dual wan setup using the sla tracked connection settings. Is there a way to configure the ASA to stay on the backup connection after activating? We had a situation where the main T1 was bouncing, so the backup connection was being activated and deactivated very often. The problem is that there is an app being used that does not allow users to reconnect to dropped connections immediately, so every time the asa switches wan connections it causes a significant disruption.I should note that I already set monitor options frequency to 240 seconds. I could set it higher, but then we have a longer delay when the main connection dies.
View 2 Replies View RelatedI have a small office with about 20 people. I currently have a T1 line which feeds a Cisco ASA 5505. I would like to replace the T1 line with two (2) ADSL lines. I need a dual WAN switch/load balancer. I researched a bit and found that Cisco RV042 will probably work for me even though I don't need another VPN and would have to disable it.
My question: Is there anothe device from Cisco or others which will give me the dual WAN and load balancing but not the VPN piece. My assumption is that it would be a less expensive device if such an animal exists.
I have an ASA 5505 current f/w & the security plus license (to get the 3 nameif interfaces). Can I split traffic between two ISPs, (VPN traffic to one destination on a T-1 on one VLAN, and all other traffic using DSL to another VLAN) and using a different nat policy on both? I know load balacing isn't supported, only failover. I was just wondering if there was a way to make this work.
View 3 Replies View RelatedOne of my remote sites acquires Internet connectivity via a cable modem service. This goes down intermittently, of course. I would like to purchase DSL service from the local telco and configure the edge ASA (currently a 5505) to use the cable modem path normally ... and fall back to the DSL path if necessary.
These seems hard to do. The edge box would need to evaluate the viability of a WAN path using some set of tests ... perhaps pings to a handful of major Internet sites. If all those pings start failing, it would stall for a minute, to give the WAN service provider time to recover ... then cut over to the second path. Cutting to the second path might mean pushing new DNS server addresses to clients (or perhaps the edge box would hand out both sets of DNS servers all the time and rely on the clients to try them all.) Once the cable modem provider restored service, the edge box would stall for a while (ten minutes? an hour?) and then cut back.
I'm willing to replace the edge box with something fancier (a bigger ASA or something sold as a router or whatever), although I'd like to stay under 10K (list) for such a replacement.
how can I setup that the backup connection will start but after 30s of icmp timeout the default gateway (tracket object - 192.168.1.1)
My configuration:
sla monitor 123
type echo protocol ipIcmpEcho 192.168.1.1 interface outside
num-packets 3
frequency 10
sla monitor schedule 123 life forever start-time now
route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 track 1
route backup 0.0.0.0 0.0.0.0 192.168.2.1 254
track 1 rtr 123 reachability
I need to move the client machines off of the 3750 (and their DHCP dependency on it) to the SGE2010 and absolutely route their internet traffic out through the outside interface on the 5505. They must also be able to communicate back into the internal environment in order to communicate with the production servers.
The clients currently use .254 addressing through a dumb dell switch to the 3750 but I am trying to migrate them over slowly to the .253. I know that the 2010 will not do DHCP, so I am putting a DHCP server on that switch right now. The 5505 won't let me add an additional nameif statement onto one of the other eth0/x interfaces and I'm not sure if that has anything to do with it's capabilities to act as a DHCP server (it's not an option in the ASDM) or it's ability to serve as the internet gateway for the 2010 clients. (Side notes: The 5505 has a base license and is currently also connecting 1 site to site VPN. As is the 5520, so all of it's interfaces are used as well).
I statically assigned a moved client with a .253 address and plugged it into the 2010. I have tried giving the 2010 both a .4 address and a .253 address but neither will allow me to ping any of the addresses on the 5505. The 2010 shows automatic routes to the two subnets and I set it's default route to 253.1. The link between the 2010 and the 3750 works - clients receive a .254 address from the 3750 and can get out to the internet via the 5505 and reach the production servers as well.
Why won't the 2010 see the 5505 as a gateway and allow clients to get to the internet and also traverse the 3750 when they need access to the production network?
The reason why I dont' just connect the two swtiches and call it a day is because I also need the production servers to ALWAYS go out/receive web requests via the 5520 outbound/outside interface. I'm having such a hard time wrapping my head around why i can't get my clients moved over to the new switch, I haven't even grasped how I'm going to do that yet.
Cisco ASA 5505 Security Plus 1 link with PPOE dialup for internet access
desirable situation: Primary link with a PPOE dialup Secondary Link with DHCP address Asignment
Problem: i want to configure Dual ISP Failover modus, but the problem exist when i configure the ip sla syntax it looks good in the running config. but after a reload the secondary line becomes primary
It looks like the ppoe client authentication is busy when the ip sla tracking mechanism becomes active. can i tweak the settings that the ip sla tracking mechanism starts later?
What i the correct config for Dual ISP setup with primary PPOE and secondary DHCP
We have got site to site VPN configured between local site with PIX515 6.3(5) and remote site with ASA 5505 7.2(4) . Because of very unreliable internet connection in remote site , we have added new ISP link which we want to use as redundant link .i understand ASA 5505 can be configured with two ISP link with SLA monitor method for redundancy as per this document ,[URL]
my question is how do i set up this pix 515 to have redundant VPN tunnel with remote site (when primiary ISP link fails in remote site and secondary ISP links takes over ) . I was thinking of using PIX 515 with 2 peers in same crypto map used for that sepcific site to site vpn tunnel,not sure that is the right way or not though.But how would i configure ASA 5505 to use backup interface(where secondar isp router conects ) to particitae in Site to site Tunnel .
At the moment I'm running a T1 to a Cisco ASA 5505 device. I'm in the process of getting a backup ISP. My question is, is it possible to configure this firewall with two ISPs so that the same internal webserver can be accessed via backup ISP?
View 6 Replies View RelatedI am trying to create a backup tunnel from an ASA 5505 to a pix 501 in the case of the Main ISP failing. The Pix external side will stay the same, but not quite sure how I can create a new crypto map and have it use the Backup ISP interface without bringing down the main tunnel.
My first thought was to add the following crypto map to the configuration below: [code]
I have two Internet links:ISP1: only Site 2 Site VPNsISP2: only HTTP/HTTPS traffic and incoming remote access VPNs With the security plus license I could correctly configure them both as active at the same time on the same ASA device. Also, I've successfully accomplished the following traffic separation:
Site to Site VPNs goes out through ISP1HTTP/HTTPS traffic goes out through ISP2 The customer request is that, when ISP1 fails the S2S traffic is relayed through ISP2 -> This is working fine, I've already tested!But when ISP1's service is restored and that link is working fine, I want that the S2S VPN traffic gets relayed through it again automatically, which didn't happen. My question is: using SLA will the S2S traffic be relayed through ISP1 again automatically when it's services are restored? If not, which technology should I use to accomplish this?
PS: This is all configured on only 1 ASA 5505 whose license was upgraded.
I have a ASA 5500 with Sec+ ?Is it possible to have Dual WAN, one WAN is used for default traffic and WAN2 would be strictly for VPN tunnels?
View 4 Replies View RelatedI created three different Remote VPN connections with three different networks . i can make them one but for some reasons i don't mix all.and iam using Cisco asa 5505 with Shrew Soft VPN software , so my problem is,- i connected Shrew soft remote vpn , if i try to connected another remote vpn connection this will not accept the second connection, any remote vpn connection software that accepts more than one connection
View 1 Replies View RelatedI have two sites with identical asa 5505's and each has the dual wan/ISP links and are set for failover using sla monitor tracking. I would like to create a vpn between these two sites that stays active regardless of which ISP link is online. Do I simply make two crytpo map statements10 and a 20 inside each of the asa's to each of the other ASA's STATIC PUBLIC IP's? [code]
View 6 Replies View RelatedI want to link ASA 5505 to two ISP's for backup purpsose. I can see this configuration example here url...
Question - does the ASA 5505 do load balancing as well for both connections - is there an example somewhere? (I do not want to buy two ASA 5505's!) which seems the only way I could find configuration details for!
i am trying to configure Dual NAT (source and destination) with multiple subnets in the source, i am trying to figure out how to accomplish this with 8.2 ASA ,
Original source
172.21.113.0/24
10.233.0.0/24
[Code].....
I have 2 Isp's connected to my Asa 5510 running 8.4.4 Ios. Can I route Dmz traffic out one Isp and my regualr traffic out the other Isp?
View 4 Replies View Relatedfor the purpose of a redundency, incase the primary ISP goes down the backup kicks in.Can this be done with the basic license (max 3 vlans) or you need to have the security plus license. (20 vlans) Currently not using the 3rd vlan (dmz)
View 5 Replies View RelatedAt the moment we want to connect the ASA on two seperate internet connections . We create one LAN interface and two WAN interfaces. Now we want to create nat rules nat our outgoing traffic. After some research and testing (on a 8.0(4) asa) we have it working.
But now we want to implemate it on our ASA, but it works a lot differerent. I can't create a nat pool (at the 8.0(4) i can assign the second interface to the existing pool) wit two interfaces,
I have Cisco ASA 5520 . I want to deploy this in the following scenario. Two ISP( for internet) links are connected in the ASA. Three zone ( Outside , DMZ , Inside) specified on the ASA.In DMZ , there are two proxy server ( proxy 1 , proxy 2) . Branch user will use proxy server 1 and Head office will use proxy 2.
In the above scenario management requirements are, Proxy 1 will use ISP 1 and proxy 2 will use ISP 2.If ISP 1 goes down then proxy 1 will use ISP 2 for internet. Please suggest me how I will configure the ASA in the above requirements or if possible send me the configuration.
I would like to knwo if i have dual ISP feature with my ASA 5520 licence? With ASA 5505 i can see Dual ISP feature but with ASA 5520 it's not!
View 3 Replies View RelatedASA5510 ios v8.4.I've setup dual ISPs and I'm trying to get ipsec VPN client access to work on the backup interface (outside-backup). The goal is to have outbound traffic on the inside subnet NAT'd through the main interface (outside) while inbound ipsec VPN clients connect and operate off of outside-backup.crypto map is applied to 'interface outside-backup,' however clients are unable to connect. If I switch the default route to go through outside-backup everything starts to work again.
View 1 Replies View RelatedI have setup an ASA5505 running 8.2 with dual ISP's
Primary link is the current live static route out and the backup picks up if the primary fails. That all works great However I have an issue with inbound NAT rules
I have configured an inbound static on the primary which works great
static (inside,primary) *.*.*.* 10.1.1.1 netmask 255.255.255.255 access-list outside_access_in line 2 extended permit tcp any host *.*.*.* eq 3389 (hitcnt=4)
Question? With the primary link active and the default route pointing out through the primary, am I able to configure an inbound NAT to the same inside host 10.1.1.1
on the backup link?
If the primary fails users will need to be able to connect inbound to this service
When I try to set it up I got this error ERROR: Static PAT using the interface requires the use of the 'interface' keyword instead of the interface IP address
So I tried that and got this error WARNING: All traffic destined to the IP address of the backup interface is being redirected. WARNING: Users will not be able to access any service enabled on the backup interface.
So what is the best practice for configuring inbound NAT for a dual ISP configured ASA
I have a site with an ASA5505 and 2 isp connections but the catch is the 2 isp's are giving me a dynamic IP so I am unable to use this [URL]
View 3 Replies View RelatedI want to create a Dual DMZ in a ASA5510 however it is not like I used to in ASA5505?In ASA5505 I create a Outside, Inside and DMZ VLAN and there after add the interfaces into the VLAN.This way I can have two DMZ interfaces, but how do I do it in a ASA5510?
View 1 Replies View RelatedMy remote office staff are stating it takes "forever" to open simple work/excel files.I think forever really means more than 5 seconds.My main office has a 5510. I have a brand new server in place here that my remote offices vpn into.
Those remote offices have 5505.
Each office has a dsl connection. Their download speeds range from 7mb to 10 mb and their upload speed are 0.5 mb to 0.8 mb.My first thought was to add a second dsl line to my main office. Then have dsl line #1 serve my main office and office 2.Then have dsl line #2 serve offices 3, 4 and 5.
Would this speed up the opening speeds of my remote offices?If so how challenging is adding the second dsl line into my 5510?