Cisco :: Install GoDaddy Wildcard SSL On WLC 2504 Controller
Jan 28, 2013
I'm attempting to install a GoDaddy wildcard ssl certificate onto a WLC 2504 running version 7.4.100.0.
I am getting the error "#SSHPM-3-KEYED_PEM_DECODE_FAILED: sshpmcert.c:4055 Cannot PEM decode private key" when downloading the .pem file to the controller.
What I have attempted to do was to export the certificate from a Windows 2008 R2 server into a .pfx file. The file contained the private key and all possible root certficates (in this case a root and a intermediate cert). Now I took this .pfx file and attempted to create a .pem file with openssl using the following command: openssl pkcs12 -in myssl.pfx -out mynewssl.pem -passin pass:mypassword -passout pass:mypassword
Now I have opened the .pem file and verified it does contain the private key and the three certificates (wildcard, intermediate and root).
View 4 Replies
ADVERTISEMENT
Feb 13, 2011
I have 3 WLC 5508 and a NAC guest server. We want to download a wildcard certificate after a few seconds at the download of this certificate I got the failure message download failed.
Accept the WLC wildcard certificates or must I generate a SAN (Subject Alternative Name) Certificate.
View 5 Replies
View Related
Sep 17, 2012
We have bought an 2504 Wireless Controller and now i want to download the newest Software, actually the Wireless Controller runs release 7.2.103. In the download section from Cisco i've found two "latest versions" the 7.0 with release date from 11.09.2012 and the other 7.3 with the release date 30.08.2012.
Now I'm a bit confused about this, because the higher release has an lower release date : Can you tell me the difference between this versions? and which version i should install?
View 7 Replies
View Related
May 3, 2012
I received a new 2504 today, I consoled on and powered it up. I see the boot sequence starting all the services. Unfortunately that's about all I can do - i try to terminate the Auto-install script but even pressing the Enter key has no effect. I can ping the 2504 but HTTP just times out. The console cable and terminal software are fine (I use them daily on a number of Cisco devices). I have done a factory reset but the same thing happens.
So, I'm thinking the unit needs to be RMA'd ?
This is what is on the current session :- [Code] ........
View 4 Replies
View Related
May 11, 2013
I have a wireless controller that works perfect but because we have some new access-points 1602i that is only supported bij software version 7.4.100.0. So I need to upgrade the controller because I now have version 7.0.116.0. I have read in release notes of version 7.4.100.0 that I first need to upgrade to 7.0.240.0 to avoid losing those VLAN settings.
Note If you have VLAN support and VLAN mappings defined on H-REAP access points and are currently using a 7.0.x controller software release that is prior to 7.0.240.0, we recommend that you upgrade to the 7.0.240.0 release and then upgrade to 7.4.100.0 to avoid losing those VLAN settings.
But I also read something about Field Upgrade Software. If you are using a Cisco 2500 Series controller and you intend to use the Application Visibility and Control (AVC) and Net Flow protocol features, you must install Wireless LAN Controller Field Upgrade Software for Release 1.8.0.0-FUS. This is not required if you are using other controller hardware models. For more information, see [URL] .....
Here is the system information of my controller:
Manufacturer's Name.............................. Cisco Systems Inc.Product Name..................................... Cisco Controller Product Version.................................. 7.0.116.0Bootloader Version............................... 1.0.16Field Recovery Image Version..................... 1.0.0Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... WIFI-WLC-01System Location.................................. System
[Code] ....
I was thinking of the following steps:
1. Backup the current config
2. Upgrade to version 7.0.240.0
3. Test and backup the config
4. Upgrade to version 7.4.100.0
5. Test and backup the config
6. Upgrade Field Upgrade Software 1.8.0.0
7. Test
View 3 Replies
View Related
Oct 16, 2011
I have deployed a 2504 controller with EAP-TLS however we are receiving the following errors where it appears the EAP response timeout from the client is expiring and not receiving a reply, this is happening with all clients.
We have three SSIDs one with EAP-FAST working perfectly, and a third with WPA2-AES itis only this where we are seeing the response appear to expire. Running code 7.0.116.0 on a WLC2504. RADIUS shared secrets all ok.
*Dot1x_NW_MsgTask_5: Oct 17 11:16:16.207: 00:19:7e:c3:ab:35 Sending EAP Request from AAA to mobile 00:19:7e:c3:ab:35 (EAP Id 224) *osapiBsnTimer: Oct 17 11:16:46.036: 00:19:7e:c3:ab:35 802.1x 'timeoutEvt' Timer expired for station 00:19:7e:c3:ab:35 and for message = M0 *dot1xMsgTask: Oct 17 11:16:46.037: 00:19:7e:c3:ab:35 Retransmit 1 of EAP-Request (length 14) for mobile 00:19:7e:c3:ab:35 *osapiBsnTimer: Oct 17 11:17:16.036:
[Code]....
View 4 Replies
View Related
May 22, 2013
I have a WLC 2504 with 5 AP licenses for which I have installed an adder license via GUI. The installation completed successfully, but I still cannot view the new license. The maximum number of APs is still showing as 5 and in fact I cannot add more that 5 APs. I tried installing the license file again, but now I get a "duplicate" error.
View 4 Replies
View Related
Aug 2, 2012
I currently have a single 2504 Controller managing 50 AP's. I am adding a Second 2504 AP Controller with 15 Lic to manage an additional 10 AP's. My current 2504 has each port configured for my four subnets that and it is managing AP's in 4 buildings. Should I configure the new 2504 the same way so that it can see all four sites? All so if the main 2504 goes down can the second 2504 take over even thou we will be out of lic?
View 7 Replies
View Related
Nov 28, 2012
I've just installed a 2504, upgraded the firmware so that 3602i ap's can attach. As a test I left the network open and am running dhcp from the 3560 switch. Why am I unable to ping or connect to a device by name within the same subnet on the "wired" network? There's no DNS server.
View 2 Replies
View Related
Jun 16, 2013
upgrade on the wireless controller 2504 from 7.0 to 7.4 is direct upgrade.My customer faced problem by upgrading the software 7.0 to 7.4 directly and the image hang.how should proceed recover the image 7.4/
View 7 Replies
View Related
Nov 11, 2012
We have a Cisco 2504 controller and approximately 35 AP's. Some of the AP's are located directly above each other (on another floor). When I run a basic annalyzer, it appears that there is some adjacent AP traffic, the controller has some of the close AP's with the same channel, so there is some RF interferance. The AP's currently are all setup for "G" and majority of the AP's are 1200 series, most of them are 1242's. Should and can the AP's be set with static channels so that there is no adjacent signals? If so where in the controller can that be done?
View 3 Replies
View Related
Oct 16, 2012
This is a new setup and has not worked yet. I have multiple 3602 APs and one 2504 Controller. I thought initially I could plug-in an AP into one of two POE Ports on the 2504. During debug mode I see that it has low power, was suprised that the 2504 switch can't fully power the AP? Is this correct?Anyways I have another POE switch that I am using with ample power. The configuration for my wireless is that it will be completely segmented off of my internal network as this is for guest access. So DNS servers are external so I cannot create host entries for the AP to discover the controller. With that being said I believe that is just one way for the discovery process to happen. I have my controller management interface and DHCP scope on the controller on the same subnet plugged into the same POE switch. The AP does seem to get a DHCP address and I can ping the controller from the AP. I cannot get any further then that. I will not join the controller and the radios get disabled. I get messages such as "discovery response from MWAR is rejected. I will post a debug log of the AP and its bootup process. This is new equipment so I would assume the firmware is somewhat up-to-date and the 3602 AP is somewhat the latest model.
View 3 Replies
View Related
Nov 29, 2012
Our current way of configuration for this is standalone ap's with multiple ssid's. The main network ssid's are on the 10.0.0.0 networks. The internet only ssid is on the 192.168.1.0 network. ( this is a wireless network only,no wired) They all get there dhcp address from a layer 3 switch. To prevent the wireless 192.168.1.0 intenet only network from getting to the 10.0.0.0 networks, we just put a simple source & destination deny acl on the in vlan interface of the 192.168.1.0 network on the layer 3 switch.Now that we are impementing a Cisco 2504 controller, the management and ap manger are both on the 10.0.0.0 network.( both on port 1 with dynamic ap manager enabled) I can setup as many ssid's on the 10.0.0.0 network and they all work fine. But when I setup the 192.168.1.0 internet only ssid it will not connect. I'm assuming that its because the 192.168.1.0 network or anyone trying to connect and use that network has to go through the controller located on the 10.0.0.0 network. I'm thinking that the acl on the vlan interafce is the problem.So, if I'm correct, what is the best way to setup a separate internet only network through the private networks?
View 7 Replies
View Related
Jun 11, 2013
Does the 2504 Wireless Controller support cad or jpg drawings? I have not been able to find in any of the menus.
View 1 Replies
View Related
Feb 28, 2013
I just completed setting up a AIR-CT2504-K9 controller with 9 APs with RADIUS on the private WLAN and an open guest WLAN; I want to enable netflow exports to a collector, but see no place in the GUI to do this and no obvious CLI commands.
View 1 Replies
View Related
May 21, 2013
-WLC 2504
-AP1602
-SW 7.4.100.0
We have 22 x AP1602.5 of them show up in the WLC with Controller Association Latency of around 1 minute and 10 seconds.The other 17 all have latency around 10 seconds.
1. What are possibile causes for high value of association latency?
2. Could high-value association latency be an indication of badly working wifi for data traffic?
View 1 Replies
View Related
May 19, 2013
I'm supporting a 2504 wireless controller with 3 aps in a health clinic. I'm interested in generating some useful information for the owners of the device such as radio utilization (It'd be really nice if there were some graphs). how I can generate these graphs without SNMP monitoring or something like Cisco Prime Infrastructure?
View 4 Replies
View Related
Jan 6, 2013
I have a question to migrate a customer from a 2106 controller to a 2504 controller. Can I use the configuration file with both controllers having the same version?
Or is there another way not having to do it again manually? The old configuration is OK, only the hardware is end of sale.
View 19 Replies
View Related
Jul 22, 2012
Can I configure the 2504 to send email notifications for particular alerts? how?
View 2 Replies
View Related
Jan 7, 2013
I have a Cisco Wlan Controller 2504 with 1042N AP (3-nos) every thing was working fine from past 2 months. Now i am getting a issue with clients which are connected to the wireless AP, they are not able to get an dhcp IP address from the 2960 Switch (DHCP Server). The clients are getting IP address as 0.0.0.0. [code]
View 36 Replies
View Related
Jun 4, 2012
I have setup guest access on the controller and this is not working at the moment.
DHCP server setup on the controller for the Guest users.
You are able to connect (get ip address from controller) and the browser gets redirected to 1.1.1.1 but then page can not be displayed instead of the login page.
View 2 Replies
View Related
Dec 16, 2012
Any online 2504 controller crash after upgrade to the point where even console port does not put anything out? Perfectly working 2504 running 7.0.116 ran upgrade through web GUI to 7.2. GUI showed perfect transfer, save etc... Asked for save before reboot. Select yes. Controller reboot and now it sits with following status lights:Power-greenSYS - amber blinkingALM - amber solidNothing out of console.
View 8 Replies
View Related
Apr 28, 2013
WLC shows the next error.
AP with MAC 00:1e:13:10:40:59 (AIR-AP1231G-E-K9 ) is unknown.
I updated the AP to lightweighd firmware using upgrade tool. But upgrade tool generate the csv files empty so I had no idea about Hash key, so I resetted the APs to default values.
WLC still doesn't register them.
How Can I register the APs? The version of the WLC is 7.3.101.0
View 4 Replies
View Related
Jul 21, 2012
I ordered controller 2504 and will arrive soon. I want to know that after configure the initial setup of 2504 (i.e. AP manager , Management IPs etc) and defining the DHCP for AP. Will the 1042 lightweight AP will register with the controller automatically or i need to manually define the AP (MAC address) on WLC. and also whether the Option 43 and 60 are correctly defined?
Management Interface: 10.10.22.15
AP Manager Int: 10.10.22.16
ip dhcp pool WLAN103
network 10.10.3.0 255.255.255.0
[code]...
View 4 Replies
View Related
Jan 24, 2013
I have a 2504 controller and 2 2602 access points. I have managed to get them connected ok to the controller. Now I'm in the home stretch here trying to figure out how to authenticate clients to active directory 2003.I have followed a really good guide on setting up the windows 2003 CA server and have got my certificates installed ok on the controller.It looks as though I have to install the client certificate on each client laptop?? Is there a method other than client certificates with active directory?
View 26 Replies
View Related
Apr 4, 2013
I am trying to setup a 2504 Wireless Controller with a few AIR-AP1262N-E-K9 Access Points. But i'm having trouble getting the access points to connect to the controller.The controller and AP's are setup at a local network at one of my customers. They are part of a quite large organization and are therefore connected to some of their other divisions in different contries via MPLS. The DHCP and DNS servers are therefore on a different subnet.I have confirmed that the Access Points do get a correct IP from the DHCP server and that i am able to ping from the controller to the AP. When looking at the controller it does not receive any join requests from the AP's. I have setup a console connection to the controller and 1 AP, so i can view debug information.Most guides mention that you can run different LWAPP commands from the CLI on the AP like show lwapp for example. But i am not able to run any of these LWAPP commands on my AP.
View 8 Replies
View Related
Nov 7, 2012
All controllers are in version 7.2.111.3.C1 is a 5508, it is ou anchor controller.C2 is a 5508, it is a big site controller.C3 is a 2504, it is a small site controller. C2 and C3 are in the same mobility group than C1 (and all is up up in mobilty managment). When "DHCP Addr. Assignment" is enable on C1 : Clients on C2 received their IP address by our external DHCP server via C1 and the guest tunneling betwenn C1 and C2 and all is working fine. Clients on C3 don't received their IP address by our external DHCP server via C1 and the guest tunneling betwenn C1 and C3, so nothing work.
View 4 Replies
View Related
May 29, 2012
I will migrate a Cisco WLAN Controller 2125 to 2504,So I have one question?I need to make all configuration into the new Wlan Controller or I can migrate with one tool or something else?
View 15 Replies
View Related
Nov 25, 2012
I am actually working in configuring a wireless controller 2504 integrated a windows 2008 server as radius server for authenticating the network users registered in a windows active directory database. The Radius server is a Windows 2008 Server with the rol of Network Policy Server.
I have been following a pair of documents in Internet, but it doesn't work yet.
Which authentication method should i use?...the Windows 2008 NPS doesn't work wtih LEAP, should i use PEAP or there is an another recomendation to authenticate the windows active directory users?
configuration tested working between a cisco wireless controller and Windows 2008 NPS as Radius Server for authenticating the windows network users.
View 11 Replies
View Related
Jun 11, 2013
I attempted to assign a User Roles template to a## 2504 controller and if failed with message stating controller version not supported. My current WCS version is 7.0172, if I upgrade to the lastest version will that resolve the template issue?
View 4 Replies
View Related
Jun 14, 2012
I found 20Mhz bandwidth enable option in 2504 controller.But what about 40 Mhz .The access points(1142) are dual band...I hope it should support in 2504 controller also.If there is no option of 40Mhz
View 2 Replies
View Related
Mar 17, 2013
CAP3501 + Cisco 2504 controller, not working MESH? So it should be, or what I am doing is not correct.
View 7 Replies
View Related
Sep 8, 2012
which controller I should use with 11 1552E AP ? I know 5508 will work with the AP's, but would the 2504 also work? If 2504 will work, I will go for the 2504 since its a cheaper solution.
View 5 Replies
View Related
