I managed to block as much of the streaming video (using URL Blocks of .flv, .wmv, etc...) how do I block YouTube.com for 23 hours of the day (or allow access for 1 hour a day)...but maintaining all the other blocks intact 24 hours a day?
Also is there a way to block p2p file sharing (BitTorrent)?
In my office there is 2 desktops which is networked. one is in the office and the other in my room. internet connection is also there, the modem is kept in my room. but one of my cousin is there in my house and he has a laptop, the internet for his lap is taken from my modem. and now i have noticed that my cousin is visiting adult content sites and i want to block him ? is there any way. why the history he uses is being shown in my browsers history ?
View 13 Replies View RelatedI found an interesting manual at this forum for blocking websites whits local content filtering. After I've modified the variables to get more details, I stopped at on question. My current Problem is "zone-pair.
zone security Z-SECRUTIY-SOURCE
zone security Z-SECRUTIY-DESTINATION
zone-pair security ZP-SECURITY source Z-SECRUTIY-SOURCE destination Z-SECRUTIY-DESTINATION
service-policy type inspect CM-INSPECT-TRAFFIC
[code]...
i run a web server out of my home hosting a website that can get several hundred people visiting simultaneously. im currently attempting to upgrade my DD-WRT flashed WRT54G V2 router with a cisco rv120w in order to sustain more simultaneous connections (existing router locks up after a few hundred). due to the amount of spam i get on my forum, particularly from IPs originating from asia pacific networks, i block all access from those IPs utilizing the IP address and CIDR. the rv120w has starting IP and ending IP to apply a rule to, but id like to block using my existing addresses from asia pacific networks with their applicable CIDR.
View 1 Replies View RelatedN600DB - Currently configured with primary computer hardwired to router, 1 laptop via WiFi, a Network booster used by iPhone/iPads and every time I wake the primary computer I get the Router Monitor alert that my internet connection has failed. By the way, I am currently using the primary computer to post this and the Belkin Router Monitor still says my "internet connection has failed" and An Internet connection cannot be established at this time. Re-booting your router may solve this problem, but you will temporarily lose your connection during the reboot.
View 1 Replies View RelatedWe have just buy a Cisco Small Business Router, model RV082. I need to enable the content filtering, but we just realized that this equipment does not filter HTTPS urls, even with the solution "Cisco ProtectLink Web" the equipment does not filter HTTPS urls.
For example, if I type on my browser just [URL], the access blocked, but if I type HTTPS:[URL], the access is allowed!Is there any way to block urls with HTTPS?
I want to make a question about RV042. I used RV042 router in my office. I used content filter feature in router.Althought this have not been apply the rules. I think I made wrong rules.I enabled the block enable forbbiden domain .And then added the websites that I want block.However, these websites are still browsing in local computer.
View 4 Replies View RelatedI face a strange bahavior with my rv220w router : I set up access rules to deny all outbound trafic for a particular IP range. It seems to work fine .... but when I enable content filtering, HTTP access on port 80 works again (and other ports are denied). It seems that activating content filtering makes the router ignore firewall rule.
View 2 Replies View RelatedI'm working withbusiness set up a remote office, currently with about 45 PC's that could grow in the future. They are looking at a RV042G or (for long term future growth) a ISA570.They want to be able to do content filtering by category, ie restrict gambling, drugs, etc. sites rather than by URL or addresses.Is either the RV042G or the ISA570 capable of doing this?Are both routers to be available long term? ie, they are not on any end-of lists? I've looked and did not see them on any.Is the RV042G capable of handling an office even starting with 45 PC's? If not, is the 570 a good fit?
View 5 Replies View RelatedI would like to set up a site to site VNP connection between 2 RV120W routers, preferably via IPsec.
The problem is that I would like/have to use a 4G modem router (model TINY) which connects to internet in front of the RV120W (on the local side)
I have no problem with that on the remote site that RV120 connects directly to internet via a public IP address on the WAN port.
Local network 192.168.1/24-----RV120W----192.168.100.1—Tiny---Public IP--------INTERNET
INTERNET--------PublicIP—RV120W—Remote local network 192.168.2/24
I've a RV120W with the last firmware version (june 2011), i want to create two vpn tunnel:
- Professional: lan routing all packet for the 192.168.0.0/24 to the first VPN tunnel
- Other: all other address IP destination to a second VPN tunnel
The first tunnel (professional) is ok but what rules can i use to configure the second ?
What is the default login/pass of cisco rv120w for ssh access ?
View 1 Replies View RelatedUpgraded to 1.0.2.6 and all of a sudden SIP devices working over the VPN no longer work. Downgrade to 1.0.1.3 and they work again. My guess is that some ports are blocked over the VPN in 1.0.2.6
I thought the general idea was that firmware ugrades fixed bugs rather than introducing them.
Suggestion for Cisco:- Zip the firmware image downloads, or else have an upgrade process that includes a CRC check, that way at least the poor punter will have an indication if they have been corrupted. I had a subtle memory problem that was corrupting some files. The firmware upload appeared to complete properly and you could log on OK but some of the menu choices resulted in a hang with the "Please wait... the page is being loaded" message. Careful checking of file sizes revealed that the file I was uploading into the router was a few hundred bytes different in size to the one on the website, must have been corrupted during the download. But the upload proceeded normally with no indication of any error. It's a pretty basic safeguard that should be in there as a matter of course with the router performing a CRC check and showing an error if it fails.
I had WRT54G2 and recently switched to an RV120W. I have an Internet accessible camera system connected to my router. Before, this worked fine... there is a dns service (DynDNS.com) that is configured as part of the camera setup. I would then just enter [URL] and I would connect to the cameras. I install the new router (RV120W) and I can no longer connect to the cameras. I do not recall any configuring that I had to perform on the old router.
why the RV120W isn't letting me get to the cameras?
Rx:, recently I have perchase 2 RV120W routers thinking that it must be very easy to setup the site to site vpn. i cannot get my remore office to link to my main office and vice verser.
Scenaro
- I'm using 2 RV120W routers for each site.
- Site A using a subnet of 192.168.10.0 mask 255.255.255.0
- Site B using a subnet of 192.168.11.0 mask 255.255.255.0
I have setup the VPN using the wizard and I got site to site tunnels connected and show as 1/1 Connected (1 user) in the status he IPsec connection status show
--Policy Name: VPNA
--Endpoint : public IP address from my ISP 203.117.222.221
--Packets Tx:145 Rx:0 and Kbytes shows Tx: 29.55 Rx:0
Q1 why I cannot use dynamic DNS naming in the policy setting ? eg: aaa.dyndns.org, I have to use the ip address instead eg: 203.117.222.221
Q2. I cannot connect from Site A to Site B , I can't even do a ping to 192.168.11.1 from Site A. even though it show the Site to site tunnel is coonected.
I've just set up an IPSec VPN between 2 x RV120W which are both behind other router. Here's what we have :
RV120W #1 (192.168.1.254) --- (192.168.1.1) Office Router #1 (PUBLIC IP) --- (((Internet))) --- (PUBLIC IP) Office Router #2 (192.168.2.1) --- RV120W #2 (192.168.2.254)
It works great, tunnel is UP.
[Code]....
I've just set up an IPSec VPN between 2 x RV120W which are both behind other router. Here's what we have :
RV120W #1 (192.168.1.254) --- (192.168.1.1) Office Router #1 (PUBLIC IP) --- (((Internet))) --- (PUBLIC IP) Office Router #2 (192.168.2.1) --- RV120W #2 (192.168.2.254)
[Code]....
Now, I need to be able to reach the server (192.168.1.100) from a PC on LAN #2 with IP 192.168.2.50. So, I've created au static route on Office Router #2 (192.168.2.1) because of course it doesn't know how to reach private subnet 192.168.1.x. My static route looks like this :
192.168.1.0 / 24 (Destination network) --- 192.168.2.254 (Gateway)
...but it doesn't work, no ping. When I do a tracert to server IP (192.168.1.100) from PC on LAN #2 (192.168.2.50), the result is :
1st jump ---> 192.168.2.1
2nd jump --> 192.168.2.254
...and it doesn't go further.
I configured my RV120W (Firmware:1.0.2.6) to count the traffic on my network. I set the monthly limit to 99999 and did not change anything else.So after a few hours, the traffic counter shows 2048 MB for outgoing traffic. This is impossible, because the DSL-connection is too limited in upload to cause this huge outgoing traffic in 6-8 hours. When I reset the counter at night, the next morning the device shows 2048MB again (even if there was no traffic at all, just some clients syncing time with NTP). I did already reset the device to factory defaults and reconfigured everything from scratch.
View 0 Replies View RelatedI have a problem with firewall rules. If I set some rules for open communication and some for closed, so I cannot reorder from the end to begin.
Last rules are at the end of all. So I can only reorder in one pages.(I have about 33 rules = 3 pages of rules)
I was wondering if I could setup my router CIsco RV120W to be able to connect to a VPN serice for my internet connection. Looking to give my small home netwok more sercurity. Is it possible with the Cisco firmware to be able to setup a connection to VPN serice. Do I have the compabilites with this router?
View 1 Replies View RelatedThe PPTP client from Windows 7 is not working with this router; therefore I would like to try the quickvpn.Is there any paper from Cisco explaining how to setup the RV120W for quickvpn ?
View 1 Replies View RelatedI need to configure a rv120w in order to make it work at the same time for data and digital tv. The fact is that the set top box for the idtv needs an IP address that will be delivered directly from the ISP. So I need to setup one LAN port that will be bridged to the WLAN connection (the stb will be connected to that lan port), and another port that will be connected to the LAN swicth so that the rest of the network has internet access. I can't see anywhere a way to create such a bridge. Quite disappointing as it's possible to do so on open source platforms such as openWRT..
View 3 Replies View RelatedWhen I try to export an SSL Certificate for a Client I get a htps . CSR file instead of the .PEM file. So, I can't update the client computer with the correct certificate.
Firmware: 1.0.2.6
I have just received an RV120W. Default setup (out of box), but when I http://192.168.1.1 and login, the next page comes up as : Internet Explorer cannot display the webpage ? Internet Explorer is version 9.
I have allowed both http and https at 192.168.1.1 in Internet Explorer security settings/Trusted Sites ?
Is there a console connection to this box ?
Is it possible to have 2 IP addresses on wan and setup specific routing rules for each IP ? Or do I need to use another router for that and if which one ?
View 4 Replies View RelatedWhere can I download the new firmware 1.0.3.10 for RV120W?
[URL]
I have been battling with my Cisco RV120W router and QuickVPN.Running Windows 7 Home PremiumPerformed a fresh install to factory out-of-box install for WindowsRemoved NortonDid NOT perform any windows updatesInstalled QuickVN version 1.2.4.1I have updated the firmware to the latest version (confirmed by cisco)I can connet to the router and have a stable connectionI can ping both the router IP and the shared file server IPWhen I enter the shared file server IP into the search field (e.g. \192.168.100.199) and press enter, I see a connection to "share", so I click on this and then see "FolderName" of my shared files. I click on this folder and I get a timed out error.When I enter the routers IP address into a browser (IE8 as factory installed) I get a timed out error also.In the past, I have installed all important and recommended updates for Windows and still get the same scenerioI have called cisco support and went through router settings, assigned them a VPN username, they log in and can access the files without issue (What the @#$$@#$)Cisco support spent plenty of time with me, but since they could access my network and since I could ping my devices, they had no other suggestions further.
I have this fresh factor out-of-box install. I know this is most likely something to do with my laptop that I am trying to use to connect to the network. I have Frontier as my ISP for home. I don't know if there is anything they are doing to interfere with my connection. I have tried to connect to the network via ComCast as well, with no luck.tell me if there is something I need to tweak in my Windows 7 settings?
I gave setup a vpn gateway between two cisco RV120W. The connection is established.
Active IPsec Security Association Table: Policy NameEndpointPacketsKBytesStateActionRxTxRxTxVPN-INTERDIO87.65.38.62000.000.00IPsec SA Established Poll Interval: (Seconds)
The problem is that there is no trafic. Even ping te remote internal nework is not working. For testing i have disabeld at both sites te firewall and have configured both with an access rule any to any.
I have a Cisco RV120W connected to the internet. I have configured a QuickVPN user on the router, but I cannot connect via QuickVPN no matter on what PC I try (with firewall or without firewal, Windows XP, 7, ...). On the router it says the VPN user is connected, but on the client PC I receive remote gateway not responding. In the logs it says failed to ping remote VPN router. I tried changing all settings I could find on this forum, but the result stays the same (changed port to 60443, deleted all IKE and VPN policies, allowed ping, disabled fragmented packets etc...). None of all the settings seems to get any result.
View 11 Replies View RelatedTrying to setup Three networks all with different IP ranges.I assume I can create a new VLAN and associate that VLAN with one of the four available ports.
Port 1 can have 192.168.1.1 - 254, Port 2 can have 192.168.2.1 - 254 and Port 3 can have 10.0.1.1 - 254.
But the Admin guide I just downloaded is NOT for 10.0.4.10. It shows Networking > LAN > VLAN Configuration.My screens show Networking > LAN > VLAN Membership.
So I am not sure how to make Port 2 associate with VLAN98 ( I created VLAN98 and 99 for the other two networks). There is a membership table that you can Tag or untag for each of the four ports - is that it ?
I recently purchased a RV120W router and I am having a problem selecting n speed under the wireless settings.
If I select B/G/N-Mixed mode then when I go to save the change I get B/G/N-Mixed B/G/N-Mixed in red letters and it does not save. If I select N only then when I go to save it says in red letters N only N only.
It does not matter if I pick 20 only or 20/40. It does not matter if I enable or disable U-APSD. It does not matter if I use the LSB or USB side.
Firmware Version:1.0.3.10 :When I got the router it had an older firmware if I remember correctly, and it would let me change to n speed.
Looking for assistance in setting up a VPN Connection on a RV120w.Trying to establish VPN with Android tablets utilizing Anyconnect.I currently utilize IPsec connections into RV120w without issues from desktops/laptops. (I am not real familiar with certificate based connection, and how to export from RV120w and import into Android)
View 2 Replies View RelatedI have RV 120W Wireless-N VPN Firewall and having issues with connectivity and communication between PCs within the same LAN. I tried the following to check connections:
1. Finding the computers within the workgroup using wondows network or (finding the computer) without avail.
2. Pinging the IP address of the PCs within the LAN. Request Timeout is given.
3. Pinter Network is working fine.
