Cisco WAN :: 2800 ISR And MPLS - How To Load Balance / Prioritize Traffic Between Them
Oct 31, 2011
We have 2mb mpls network between three sites. Each site also has its own internet connection for hosting webserver and internal users to access internet. Each site has a few internal subnets. Each site currently has a 2800 series ISR.
1) Increase Internet connection to 10mbps and configure site-to-site VPNS in a mesh configuration so that each site has a vpn to each other site. This would create six vpn tunnels.
2) Configure so that only Exchange and VoiP traffic use the MPLS network under normal conditions. All other traffic (backup/misc apps) should be routed to use the Internet VPNs. If the MPLS fails of course we would like the Exchange and VoiP traffic to fail over to the VPN connections as well until the MPLS comes back up.
View 2 Replies
ADVERTISEMENT
Jan 9, 2010
what you're doing to load balanace internet traffic? I'm interested in load balancing internet traffic (outbound -AND- INBOUND) using multiple (at least 2) ISPs. Some of the methods I have used in the past have certain weaknesses.. basic DNS load balancer (relies on multiple IP addresses per host), OER/PFR (ability to control INbound is limited unless complex configuration and coopearation with ISPs)... This is kind of a broad open ended question.. It seems like something that would be a common issue and am wondering what other are doing with the capabilities 2800, 2900, 3800, 3900 series routers..
View 6 Replies
View Related
Oct 29, 2011
ISP environment with 3 Cisco 7200 BRAS ( NPE-G2 ) , we need to load balance traffic between two of them so the load balancer will accept traffic from backhauling link and distribute traffic the upper two BRAS , can we achieve this using spare 7200 we have or is there any software solution can do this .
another question , Cisco 7200 VXR ( NPE-G2 ) , does it support concurrent calls or sessions from more than 16000 subscriber ?
View 13 Replies
View Related
Jun 28, 2011
We are now using a ASA 5510 firewall and we would like to configure a internet load balance traffic in our environment.For example, some IP addresses go through local gateway for internet routing but some address go through VPN tunnel gateway.
View 1 Replies
View Related
May 6, 2012
i am having a problem of load balance traffic over two WAN links connecting our 2 cisco 7600 routers, as i just knew that 7600 is not supporting per packet load sharing only per destination and as per our monitoring tools that one link is underutulized the other is overutilized.
View 10 Replies
View Related
Apr 28, 2013
My HO is connected to BOs over MPLS Links.The links are terminated on routers but i dont have access on those routers as it is maintained by the ISP.Behind of the HO router there is s 3560 switch. Can i configure this switch to prioritize some traffic over the WAN link to the BOs.
View 4 Replies
View Related
Jul 8, 2012
I Do want know what could be best Device to prioritize Skype Traffic i mean should i implement it on Cisco 3560 or squid or Mikrotik according to my current scenario to get best result.Also do Let know how to Prioritize Skype Traffic in Cisco 3560 Switch
View 2 Replies
View Related
Jul 18, 2011
I need to prioritize voice traffic through the ASA
priority-queue outside
tx-ring-limit 200
queue-limit 2000
Do the above values look correct? and why is the priority queue applied to the outside interface and not the inside? (or both). Also is this the part that ensures that the regular traffic does not choke the voice traffic?
class-map voip-class
match dscp ef
policy-map outsidemap
class voip-class
priority
service-policy outsidemap interface outside
Will the global policy remain which this interface policy taking priority?
View 10 Replies
View Related
Jul 1, 2012
We need to give TCP 3389 & 3399 priority over all other traffic between a Cisco 1941 and 2951.What is needed to do this?
View 6 Replies
View Related
Sep 25, 2012
we're looking to use an ASA5505 or 5510 as our firewall but want to see if one of them can prioritize traffic. I know it does QoS but we're wanting to dedicate x amount of our bandwidth to traffic based on destination IP address. Is that possible and does it take a license upgrade?
View 3 Replies
View Related
Aug 6, 2012
What is the best way to load balance traffic between an FWSM and ASA 5520? Both are attached to a 6509-E (in seperate VLANs). The problem is the FWSM doesn't support any dynamic routing protocols (in multi context mode). So with my limited knowledge I don't see a way to do this.
View 8 Replies
View Related
May 20, 2012
Is it possible configuring load balance with three intefaces, in my router with the following features?I have three ISP, and would like balance the traffic ... Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.2(2)T1, RELEASE SOFTWARE (fc1) Cisco CISCO2911/K9 (revision 1.0) with 483328K/40960K bytes of memory.
Processor board ID FTX1613AH8D
3 Gigabit Ethernet interfaces
1 terminal line
2 Channelized (E1 or T1)/PRI ports
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
[code]....
View 3 Replies
View Related
Aug 3, 2011
I am using 192.168.1.1 as database server in head office. my branch user are more than 500. all user hit at 192.168.1.1 for database. Now i want to NAT with application server 192.168.1.50 and 192.168.1.51 with load balance As some user hit 192.168.1.1 form branch but traffic go to 192.168.1.50 and some users traffic go to 192.168.1.51.
I want to do it in My core router (Cisco 3845) in Head office. How i do these two things ?
View 1 Replies
View Related
Feb 6, 2013
So I can fail over my NAT and IPSEC VPN (DPD). I am curious can I load balance my WAN links too?
I have a route map that is used for fail over, I just can't quite think how I would load balance the links
ip nat inside source route-map 10mb interface GigabitEthernet0/1 overload
ip nat inside source route-map efm interface Vlan3 overload
ip route 0.0.0.0 0.0.0.0 213.38.xx.xx
ip route 0.0.0.0 0.0.0.0 46.226.xx.xx 10
access-list 175 deny ip 172.16.20.0 0.0.0.255 172.31.114.0 0.0.0.255
[code]....
View 2 Replies
View Related
Mar 22, 2012
i am using two internet connection if one fails the other want to connect automatically is there any hardware.
View 2 Replies
View Related
Apr 22, 2011
We configured sa520 load balance with 2 isp 2mb+2mb how to check the status of the load balance on sa 520 .
View 1 Replies
View Related
Jun 6, 2011
I have problem with VPN and Load Balance at the same time.VPN (Gateway to Gateway) between two RV042 routers is working fine with only one WAN or two WAN's with Smart Link Backup. If i switch to Load Balance communication through VPN is almost impossible.
I have postgres server (port 5432) in first location and clients in another. Clients cannot connect to server or lose connection after while. This is example, but every communicaton except ICMP over VPN with Load Balance enabled is faulty (file sharing, RDP...). Everything works fine using public IP and port forwarding or VPN with only one WAN.
If i understand it correctly Protocol Binding should affect only "normal" communication (outside of VPN), but it looks like VPN communication is also divided between WAN1 and WAN2. Of course this cannot work this way because VPN works only with one WAN.
Another question - is it possible to bind communication TO selected target port with RV042 Load Balancing to selected WAN?
View 2 Replies
View Related
Jul 26, 2012
I would like know, what license is necessary to employ a load-balance in a 2911 router. I have these licenses bellow, can i configure an load balance?In this cenario we have two links with an ISP.
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.2(2)T1, RELEASE SOFTWARE (fc1)
Cisco CISCO2911/K9 (revision 1.0) with 479232K/45056K bytes of memory.
Processor board ID FTX1613AH8D
1 FastEthernet interface
3 Gigabit Ethernet interfaces
1 terminal line
2 Channelized (E1 or T1)/PRI ports(code)
View 6 Replies
View Related
Nov 1, 2011
We have a Dlink Lb 604 router. We have two wan connections. Connection 1 has a speed up to 8 Mbps.Connection 2 has a speed of 1Mbps.We set the load balance to 50-50. When we tested the speed with two lines it is showing 1 Mbps only.When working with connection 1 we are getting speed upto 6 Mbps.
View 1 Replies
View Related
Aug 30, 2011
I have a D-Link DSL 2640B on the way which I plan on using to replace my 2Wire modem. The 2640B is a combination of a modem/wireless device. Does it dynamically load balances the internet connection? Sometimes while I'm playing online games on my PC and a few others are using the internet for browsing or Youtube, I lag A LOT. Latency shoots up from 10 to 200. QoS goes to ****. And I only need 0.50-1Mbps to keep a steady online play. This was the problem with my 2Wire. So does the 2640B load balance the bandwidth?our max speed is 3.5Mbps according to the ATT Rep.
View 10 Replies
View Related
Jan 10, 2012
i need to know how many links i can using with load-balance on the same router ? i have router cisco 2901 , 3 providers , every provider having 4 links can i load balance between 12 links ? i am using static route
View 11 Replies
View Related
Jul 17, 2011
What is the load balance method of 3750 port channel ( by source ip , or by source mac ) to diver traffic to paths? I have tried to use 10.242.104.101 and 10.242.104.102 as source ip, it will travel to the same link (G0/1) within one port channel (G0/1+G0/2). Howerver, if I later use 10.242.104.109, then this time it will traffic to G0/2 link. What's the concept behind.
View 1 Replies
View Related
Jun 30, 2012
I want to split my traffic between two ISP's. I want all traffic to pass over one connection EXCEPT my VPN tunnels, which I want to use the second ISP. How should I set up (protocol binding?) to accomplish this? (I have run into various problems trying to load balance all traffic. So I am trying to "partition" traffic.)
View 1 Replies
View Related
Apr 16, 2012
I have set up an RV042 v1 and v3 both in Load Balancing mode. Set in Router mode.I want one of the WAN ports to be preferred so I added a static route to 0.0.0.0 metric 5 to that WAN.Sometimes the route shows in the routing table and sometimes it goes away!!
View 2 Replies
View Related
Mar 4, 2011
I have two ISP circuits and the following devices in hand:
1. Cisco ASA 5510
2. Cisco 2800 router
3. Cisco 3750 switch
I've finished a part of the configs on above equipments, please refer to the attached diagram.And I'm making a test in order to achieve the below features:
1. By default, packets from PC1 go out through ISP 1. Packets from PC2 go out through ISP 2
2. When ISP 1 is down, packets from PC1 changed its way to ISP 2 through the 2800 router. And when ISP 2 is down, Packets from PC2 changed its way to ISP 1 through ASA 5510.
View 2 Replies
View Related
Feb 15, 2012
I have several RV16 with two internet connections each one, but different speed each wan connection, it takes the slowest wan connection allways, I use the round robin option, any clue in configuring?
View 1 Replies
View Related
Aug 1, 2012
--- I have 2 WLC's 5500 that I have to set up on my network with the same configuration except I am not sure that they can be load balanced.
-- My only thought is to take a full class C and on each WLC set up a /25, thus each device can provision 120 IP's
--- This seems a bit archaeic, but is there anything else smarter to do? Can they be load balanced?
View 9 Replies
View Related
Apr 24, 2013
We want to us an ISA570 and load balance between two isp connections, two of our switches will be standalones and not connected to one another. One switch will be for data and another VOIP/Data. The ISA will also do NAT and we need to make sure that the VOIP network can get out to the first isp. I assume we will need a static route for that to make sure it goes out the right isp. I just don't know if routing mode needs to be enabled in order to specify a static route, because I heard you can't have NAT and do routing mode at the same time.
View 2 Replies
View Related
Oct 16, 2011
How to load balance two/three ISPs using ACE.
What might be the default gateway?Can i create a serverfarm with two rserver with different subnets?
View 4 Replies
View Related
Mar 16, 2013
I configured a RV042 to load balance 2 WANs. It appears to working well but I would like a 2nd opinion as to whether or not I chose the proper settings to accomplish the task.
1. WAN1(ISP1) is the existing internet connection(1.5mb T1). I have a block of static IPs with ISP1.
2. I added ISP2 to the RV042's WAN2 connection to increase bandwith (10mb). I only have one static IP on ISP2.
3. I want everyone on this router to use WAN2... well... almost everyone... for the most part.
4. I want to keep WAN1 active on this router because there will be periodic inbound connections using static IPs (from ISP1) that are setup with one-to-one NAT. I also have a voicemail system that needs to continue to use ISP1's email relay (SMTP,25).
Anyway, I was able get the outgoing traffic that had to remain on WAN1 working with protocol binding. In order to get the router to use WAN2 for pretty much everything else, I set it for load balancing and set "Max. Bandwidth provided by ISP" for WAN1 up & down kbits/sec both to 32 (very low). I left the WAN2 up & down settings to the actual speed of WAN2.
The result is very low traffic on WAN1 and lots of traffic on WAN2 which is what I wanted. Did I do this right? Is there another preferred method to accomplish this.
View 2 Replies
View Related
Apr 25, 2012
I have 3 877 ADSL routers for internet connectivity. I recently installed a FW behind them and would like to use the Ciscos as load balance in order to get better utilization from my 3 internet links.
1) the 3 routers are on DHCP from the ISP on the WAN side.
2) the 3 ciscos are on the same class C subnet on the LAN side: 10.201.1.252, 10.201.1.253 and 10.201.1.254
View 3 Replies
View Related
Apr 16, 2012
Have two ACE 4710 in HA setup. We would like to setup HTTPS loadbalance(actually just a primary and standby configuration in the serverfarm). Initially this would be for Exchange OWA connections but may expand to more HTTPS connections later. I know there are several ways to do SSL with the ACE( client, server, end-to-end). I am just wanting to know the easiest way to deploy this? Is a certificate always needed on the ACE for each connection? In HA mode would a certificate be needed for both or does it replicate in some way to the other ACE?
View 6 Replies
View Related
Jan 28, 2013
I have been experiencing some issue with a portchannel interface.I have two cisco switches 3560 and I have a portchannel between them ( It is composed by two gigabitethernet interfaces generating a portchannel of 2 Gigas ).Unfortunately, I am verifying that one interface traffics about 893MB but the other interface only traffics about 100MB.Is there any cause why is this happening? I thought that maybe both interfaces would traffic about 450MB.Is there some wrong configuration with the load-balance command?. At this moment there is no load-balance, It is only configured the port channel with the default configuration.
View 5 Replies
View Related
