Cisco :: 4402 WLC / LMS 4.2 Threshold Coming
Mar 1, 2012
I'm using RADIUS and FlexConnect APs. The issue is intermittently users will lose connectivity as if they're de-authenticated. Their clients still believe they're associated to wireless but they have no network connectivity. On Windows 7 we receive the exclamation point over the signal strength indicator.
There doesn’t seem to be any rhyme or reason as to what is causing this. It doesn’t seem to happen at any particular time intervals or anything else I can identify. Sometimes users will go entire days without experiencing connectivity issues sometimes they can’t go five minutes. When the clients are experiencing the issues they cannot even ping their default gateway.
The setup was initially the following:
Site A: 1142N APs and RADIUS server (server 2003) users are authenticating to.
Site B: Flex 7510 running code 7.0.116
Between site A and site B there is a site to site VPN with no restrictions.
After some time of working with TAC and not getting anywhere I setup the following:Site A: 4402 WLC running code 7.0.116 connected the same 1142N APs HREAP mode. I had the same issue with connectivity with that setup.Today I changed over to local mode and as of yet I haven’t had reports of connectivity issues.
When running ‘debug client MAC’ I see no indication of connectivity issues. I also have an NCS and I don’t see anything indicating what the issue is there as well. I’ve tried with both enabling and disabling ‘H-REAP Local Auth’. We seem to experience the issue in H-REAP standalone mode as well.
View 10 Replies
ADVERTISEMENT
Mar 18, 2013
How to find out which Fault Threshold group a specific interface belongs to.The scenario is that in Fault Manager there is an alarm for which I want to change the Threshold Setting.
Example Alarm:
Event_Description HighUtilization
Device IP x.x.x.x
Device Type Routers
Fault Last Updated At 19-Mar-2013 09:44:25
Component IF-router2.x.x/26 [Tu187] [x.x.x.x]
[Code] .....
View 1 Replies
View Related
Jun 27, 2012
In WLC i see the roaming option to controller the handover. As the accompanying graph [URL], how do I up or down the threshold of the handover? or, How do I more sensitive to IP phone(NEC model MH240)?
I don't understand the four textfield of the roaming options URL
View 6 Replies
View Related
Apr 30, 2013
We're getting complaints about a specific 1131AG in the field only being intermittently accessible. WCS shows both the a and b/g interfaces randomly bouncing, sometimes the reason for the bounce is unknown other times it says it's because it lost connection to the controller. I can ssh into the WCS but the engineer who setup the AP's doesn't seem to have enabled remote access via telnet or ssh.
We are also seeing these events:
802.11a interface of AP * is down: Controller 172.17.0.10 Reason: Max retransmissions for the AP have reached.Interference threshold violation reported by '802.11b/g' interface of AP *, connected to Controller '172.17.0.10'.I know I can adjust the threshold percentage, but that would only seem to mask the issue.WCS gives this version info on the AP:
Versions
<DIV style="DISPLAY: block" id=versions mcestyle="display: block;">
Software Version
6.0.202.0
Boot Version
12.3.8.0
[code]....
View 14 Replies
View Related
Oct 4, 2012
On a Cisco ASA 8.4 code is it possible to receive an alert once a certain number of tcp/udp connections is reached? I'd like to see if I can get an email alert or syslog if the ASA reaches say 2,000 connections for example. Once I get an alert I could then investigate the cause of so many connections.
View 1 Replies
View Related
Mar 11, 2012
I need a WCS report that will actually give me the top n Wireless Access points that have too many clients trying to authenticte to them.We have some serious capacity issue in meeting rooms but we need a ball park figure of how many WAPs might be affected.
I know I can interogate the WCS to drill down and find out that WAPs are exceeding their threshold I just need to have a decent report generated.I have searched the reports from WCS 6.0.202.0 and cannot seem to find anything that suits.
View 4 Replies
View Related
Mar 8, 2012
I am working on a QoS design which I hope to test at some point, but at this stage its from the books.My question is how to decide which queue and threshold to use for video traffic, then lower priority traffic.I understand the shaping and sharing commands, its the queuing and threshold bit I'm not clear on.The plan is to use the priority-queue for EF marked voice, this will be policed on ingress to provide an upper limit to EF traffic levels, then my second priority traffic will be video. Which queue will get serviced first once the priority queue is empty, and how do I decide which threshold to allocate my video traffic to? The document ion is not at all clear, I want to prioritse my traffic in the following order:
1 voice, use the priority queue
2 video, this to get serviced ahead of data, after voice.
3 interactive data
4 Bulk data
5 Best effort
So Q1 settings are ignored due to priority queue. Q2 gets 70%, Q3 25% etc.Is it as simple as putting video into Q2 T1, then interactive data into Q2 T2, will Q2T1 get a higher priority over Q2 T2 once the PQ is serviced?
View 4 Replies
View Related
Jan 18, 2010
I've read some opinions that lowering the RTS threshold can facilitate in some noisy wireless environments. I have found how this can be done on standalone APs but cant seem to implement the change on a WLC 2112. How to do it.
View 3 Replies
View Related
Jan 10, 2013
I have a switch where the current power threshold is set to -20.0db. The problem is that the receive power fluctuates between -19.9db to -20.1db, which is causing it to throw alarms on my solarwinds monitoring server. What I would like to do is change it to a different warning threshold, but I can't seem to find the command to do so. This is a catalyst 3750 running IOS version 12.2(55)SE3. [code]
View 5 Replies
View Related
Aug 9, 2011
I set the Cisco's AP settings with MTU size as 1200 bytes and the Fragmentation threshold to 256 bytes. Set up: I am using a WiFi enabled laptop connected to Cisco AP running an application pumping data of size 1400 bytes continuously to a Wireless node connected to the same Cisco AP over WiFi.
I am monitoring network activity on the same laptop using Wire shark.However,i cannot see 1400 bytes data getting fragmented. What is the concept of fragmentation and MTU size? Also,I would like to know how to change the AP settings so that i can see the data (1400 bytes)getting fragmented to small byte chunks.
View 1 Replies
View Related
Nov 6, 2011
following errors.
Nov 7 21:34:50: %EARL_NETFLOW-SP-STDBY-4-TCAM_THRLD: Netflow TCAM threshold exceeded, TCAM Utilization [99%]
Nov 7 21:44:44: %EARL_NETFLOW-SP-4-TCAM_THRLD: Netflow TCAM threshold exceeded, TCAM Utilization [91%]
I've already found this kinds of cases, in this community. So, It seems that Changing the current configuration to 'mls aging fast threshold ## time ## ' is most suitable in our situation.But, I don't know how to calculate the apt threshold value and time value.
[1] sh run | in mls
mls ip multicast flow-stat-timer 9
mls flow ip interface-full
no mls flow ipv6
no mls acl tcam share-global
mls cef error action freeze
[code]....
View 1 Replies
View Related
Sep 19, 2012
I have an RV042 (it's old, silver/dark grey plastic front one) w/ firmware 1.3.13.02-tm.
The reason we bought this (long ago) was to balance two WAN connections, one with unlimited data and one capped monthly. It did that once, but for a couple years both connections have been unmetered so it's just been balancing them 50/50. As of today one WAN connection (the new much faster one) is back to being metered but I can't figure out how to configure the RV042 as it once was to prefer sending traffic over the slow, unmetered connection first, and only use the faster metered connection when necessary.
It's been a long time and honestly I only vaguely remember the ability to prioritize a connection based on % of bandwidth used so that all traffic would go over the unlimited connection 1st until it was flooded, and only then fall over to the metered connection. This is totally different than the weighted round robin, or smart link backup.
I found this 3rdparty forum post that supports that vauge memory and suggests this was eliminated between firmware 1.23 and 1.3: [URL] Is it possible to replicate this functionality with the current firmware? if so how? If not, how to do roll back to firmware 1.23?
It sounded like perhaps I could assigned WAN1 a bandwidth of 100000 (even though it's really 1500) and then assign WAN2 a bandwidth of 1 (even though it's really 20000) and the result might be the prioritization I'm looking to achieve... but I feel like I'm stumbling in the dark at the point.
View 1 Replies
View Related
Feb 5, 2012
One of my clients is using Cisco catalyst 2955 industrial switch.I am doing the configuration for them and come across one setting of FCS Error Hysterasis Threshold. I know FCS is Frame Check Sequence.
I do not understand is what is the meaning the setting of Hysteresis in term of percentage stand for what purpose?For example, the default is 10 percent. If I set the value to be lower 5% and what is the impact on that? Is this more stringent than default of 10% or less stringent than default of 10%?
View 4 Replies
View Related
Dec 7, 2010
Recently I faced 1 issue in MLS 6509.MLS had all Gig modules in slots 6,7,8 taking System detected CRC error rate on port ASIC data bus exceed fatal threshold, ("System detected CRC error rate on port ASIC data bus exceed fatal threshold".) causing the module reset by the SUP. After this active SUP causing it to failover the standby. This process was continuing every few minutes resulting in the SUPs on MLS rolling.what could be the issue for Sup rolling reset?
View 1 Replies
View Related
Oct 20, 2011
I am slowly getting this router configured........I am up and running. Traffic from All nodes inside can go outside. My next step is to configure traffic coming in to go to my server. I have Web, FTP, SMTP and POP running on the same server in my LAN. I need to us NAT/PAT to direct incoming traffic to it. I belive I have this done correctly, but obviously not...I only have port 80 configured in the config file, if I can get that to work the rest would be the same........
View 1 Replies
View Related
Mar 7, 2013
why Cisco 2921 Gigaethernet 0/1 is not coming up ? I also tried to connect the interface to another SWITCH with no joy.
ME3400 (ISP's switch)<-------------MPLS link--------------> Cisco 2921 Gi0/1 >>>>>>>>>>Port not coming up
I tried connection between ME3400 (ISP's switch) and spare switch and the INTERFACE of spare switch was in UP/UP state .Troubleshooting I did so far on Interface Gi0/1
1> Changed ths speed/duplex manually and revert it back to auto
2>diable keepalive
3> Tried differnet LAN cable with no luck
4> Please see HIGHLIGHTED part (in red colour) of "Show controller Gi0/1" command
I am pasting some of the SHOW command output R2921_MMP#sh run int gi0/1Building configuration.[code]
View 8 Replies
View Related
Apr 24, 2013
i am trying to make a simple Site to SiteVPN between two offices, one has Cisco ASA and one has RV042 router.when traffic initiated from ASA side, i keep getting this message in Debug and tunnel wont come up
.
[IKEv1]: Group = A.A.A.139, IP = A.A.A.139, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.Apr 26 00:15:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
whereas if traffic initiated from RV042 side, i keep getting this message in debug and tunnel wont come up.
Apr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, Oakley proposal is acceptableApr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, IKE SA Proposal # 1, Transform # 0 acceptable Matches global IKE entry # 6Apr 26 00:43:44 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, Freeing previously allocated memory for authorization-dn-attributesApr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, PHASE 1 COMPLETEDApr 26 00:43:45 [IKEv1]: IP =RV.RV.RV.139, Keep-alive type for this connection: DPDApr 26 00:43:45 [IKEv1 DEBUG]: Group =
[code].....
View 1 Replies
View Related
Apr 16, 2013
I try to connect 3750X (15.0.1(SE3)) with PC or router that is interface card is fixed to 100Full on 3750X-12S-E I plug a SFP-T, this SFP is ok: [code]
But with Speed and duplex fixed the interface is up arround 1-4s and move to down and errer-disable.
View 2 Replies
View Related
Oct 29, 2012
our FWSM (in 6509) is not coming up, when tried to sesssion up using "Session slot 1 proc 1" command,It is giving error , "Tyring 127.0.0.11 .....connection timed out remote host not responding".
In "show mod" command output at Switch in IOS console: under Card Type Section: it is showing Model & Serial Number correctly, Under MAC address sectino: displaying some MAC address But in Online Diag Status, it showing "Unknown" for Module 1.
We tried re-seating in other slots, but of no use. Giving same error. Some of other forms are saying it is the issue with 128 Mb CF image problem, FWSM is no more reachable from 6509 IOS console. We even tried using FWSM console (using PC-Conse & LCP Console) but FWSM is not contactable.
View 1 Replies
View Related
Sep 22, 2011
We are running LMS 3.01 and have been currently experiencing issues regarding the login page. It has been stuck on the page that states "Server Not Ready - System is coming up - You will be redirected to login page soon". It has been like this for the past few days:
I've tried restarting the daemon services as well as rebooting the server which has made no difference.
View 10 Replies
View Related
Mar 25, 2013
I have a small problem and I'm a bit confused, Cisco suggested that you should mark traffic as close to the end devices as possible. So I wanted to try marking the traffic coming from S1 to R1, S2 to R2, and S3 to R3 on Switch 2 (Cisco Catalyst 2960) with the following config:
[code]...
View 9 Replies
View Related
Jul 6, 2012
I have network: 20 PC's conected to a switch (ordinary switch), from switch to a router (for DHCP and internet conection), Router is connected to a cable modem.
Lately an issue arised. One PC started having problem witch connection (PC is windows 7, up to date). PC instead of 192 addres is getting 169 (i need to highlight it is a problem with only one PC). That means the PC is connected to the Router but it is not getting proper IP addres. After changig the addres to static the connection ws fine for few days and then in networc connection icon (botom right) it came up with 'unidentified network' message. I changed the patchleeds, even changed the connection with known working line (from outlet to patchpanel) and the connection was coming and going. Then I changed network card with the same resoult. I noticed strange thing: While the IP is 169 or when 'unid net' when I unplug the cable from outlet then plug back and do so couple times in one moment the connection is back and stable but only for some period of time. Cables had been re terminated with new jacks and at the patch panel. Drivers for network card are up to date.
Why is the connection coming and going?
View 3 Replies
View Related
Feb 17, 2011
I live in a house with four other people so I need a lot of free ethernet ports.I currently have three routers daisy-chained together and I want to add a fourth, but I can't seem to.When I plug it up, pages refuse to load on computers connected to it. I read something about disabling DHCP, but I have two other routers chained to my primary and didn't need to do that. This one's branching off the main one though, instead of being at the end of the chain.I'm trying to hook up either the Linksys 4-port wired router or the 8-port one (I have both). I tried disabling DHCP on it and setting the IP thing to 192.168.2.1 instead of 192.168.1.1 and it worked for a few minutes, then nothing.I also tried that with the TRENDnet one and the same thing happened (had to reset that one to factory defaults).Is it possible to have two routers coming off another or does it need to be a proper chain? Why did I not have to disable DHCP on the others and they still work fine?
View 4 Replies
View Related
Nov 21, 2012
For some reason when I'm watching a HD video or I'm downloading a file, on my HP laptop my wifi decides to stop,disconnect and then start up again This never occurs on my iPhone iPad Xbox or any other laptops in the house.
View 1 Replies
View Related
Jan 9, 2011
how can make sure i am recving mbps that i am paying for?
View 2 Replies
View Related
Mar 1, 2012
I am unable to view my qms 2200 on my window 7 network. I have checked drivers, ip addresses and just about everything I can think of I have even hired 2 different tech people who were unable to get as far as I got and charged me an arm and a leg. the message I get from the trouble shooter is contact your network admin and the printer is offline. What or how do I find the what seems like a simple solution to get the printer online before I stub my toe on drop kicking this thing....
View 1 Replies
View Related
Apr 25, 2013
i am trying to make a simple Site to SiteVPN between two offices, one has Cisco ASA and one has RV042 router.when traffic initiated from ASA side, i keep getting this message in Debug and tunnel wont come up
.
[IKEv1]: Group = A.A.A.139, IP = A.A.A.139, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.Apr 26 00:15:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
whereas if traffic initiated from RV042 side, i keep getting this message in debug and tunnel wont come up.
[code]....
View 2 Replies
View Related
Oct 2, 2012
I have a CISCO2921. I am not able to bring up its gi0/1 interface. It stays down down.
[URL]
I know that interface is not coming up because of "no media" below. Router#sh int gi0/1 | i media Auto Duplex, Auto Speed, media type is no media
I have tried media rj-45 and media sfp which have also not worked. The other end of this link is ethernet handoff. What is it that I have to do for the link to come up? If I change the connection to gi0/2, I think that will work because I see this for gi0/2:
Router#sh int gi0/2 | i media Auto Duplex, Auto Speed, media type is RJ45
View 10 Replies
View Related
Jan 22, 2013
I have hardcoded 1GB ports on 3750X to 1000 and full duplex for all servers connected. THe ports are not coming up with this speed and duplex settings. If I configure them to 100, I am able to see the port is up. Whereas if i connect the same servers to 2950 switches, i can see the ports working fine with 1000 speed ..we have tried with the latest universal IOS as well
View 7 Replies
View Related
Sep 23, 2012
I 'm trying to set up a home lab with a couple of 28XX and 2651XM series routers.I would like to simulate a frame-relay connection between HQ, Branch1 and Branch2 . All of them are conneced to a PSTN switch (2811 router) via T1 cross over cables. The connectivity is like this. [code] I have configured all the routers and FR switch with necessary configuration. However the link between HQ and Branch1 is not coming up. On both the routers I could see the line protocol is down.I have pasted the configuration below.[code]
View 4 Replies
View Related
Feb 22, 2013
We have configured Cisco 3750X POE series switchs with Stack.WS-C3750X-48P each with Redundant 1100W & 715 W PSU's. They are configured with Stack-Power in Sharing mode and the switches are Smart Stacked as well.IP Phone and Access points are connected its working in last two years,
Now we are facing some issue on Cisco IP Phone and Access point, When i have problem if unplug (disconnect & Reconnect) the IP Phone from Switch port,Power is not comming on switch port.Plug it into another switchport of the same Switch it may not power in any port.I tried shut & no shut and reconfigured on switch port , I have verified multiple switch ports same issue on the switch I have changed cable.
View 2 Replies
View Related
May 31, 2011
Last night I switched out our old Cisco pix 515 with a asa 5505. The config is the same and internet and outgoing mail is working but no mail is coming in. Below is a copy of my config. Why my inbound mail is not coming in.
smtp 192.168.51.248 (Barracuda email filter)pop3 192.168.50.11 (exchange server). Tried to telnet into the firewall but connection timed out. Went to mxtool box and that also timed out while trying to connect to smtp. Port scan from mxtool box timed out too on all ports.
[Code] ........
View 5 Replies
View Related
Jul 21, 2012
I have 2 ASR routers running PIM-SM between them on several sub interfaces.PIM hello interval configured for 200ms.Sometimes PIM neighbors between ASR routers going down.
Reboot for each router not resolving the problem.Deleting ip pim sparse-mode and configuring it again on one of the ASR routers resolves the problem.
I didn't find any related bug.The version is asr1000rp1-adventerprisek9.03.06.01.S.152-2.S1.bin
View 6 Replies
View Related
