Cisco AAA/Identity/Nac :: Authentication Error In ACS 5.3
Sep 7, 2012
I configured ACS 5.3 and added AAA clients with TACACS+ server and shared secret key as cisco123. i did the below config on switch also. when i try to authenticate login with ACS it does not respond. Find the configuration and debug output.nd
In debug output it gives ruser and rem_addr is null. i did not understand why .
I am able to ping to ACS server and i used telnet 192.x.x.10 49 and it gives the proper output.
aaa new-model
aaa authentication login default group tacacs+ local
!
tacacs-server host 192.168.60.10 key cisco123
tacacs-server directed-request
ip tacacs source-interface Vlan172
View 2 Replies
ADVERTISEMENT
May 15, 2013
I have an 1841 that was working fine - I could SSH to it with my Radius login and console into it with local credentials ("Fred").I added another use ("Mike") with priv 15 so the end user could log in locally via console if needed.After that, we can both log in via console, but when we try to enter privileged mode we get "% Error in Authentication", before even entering the password.I can still log in via Radius SSH with no problems and access privilege mode via SSH.What am I missing so we can have two different users be able to log in locally with different credentials and access privileged mode, and keep my ssh radius working?
View 3 Replies
View Related
Nov 22, 2011
we have ACS 4.2 and 2851 router with IOS 15.0(1)M4. There is authentication failure with error no 254. Is there any compatibilty issue with 15.0(1)M4 IOS
View 1 Replies
View Related
Jun 11, 2012
We are using acs version 4.2.0 build 124 on windows server 2003. Our domain controller has been upgraded from 2003 to windows 2008 R2.Now we are facing following error in ACS authentication for accessing our devices.Error: AUTH 06/09/2012 11:55:40 E 1810 3316 0x8f21 External DB [NTAuthenDLL.dll]: Windows authentication FAILED (error 1326L)if we restarted services of ACS server then users get authentiated fine.
View 1 Replies
View Related
Mar 2, 2011
I have two 1310 bridges. one configured as root and the other as non-root. Authentication Settings: Open with EAP and Network EAP with no addition. Set up: when non-root bridge tries to associate with root bridge, root bridge checks with radius server if it's ok to associate with the non-root bridge.
I can see communication with the radius server (I'm using FreeRadius) and the radius server even sends a SUCCESS back to the root bridge. However I'm seeing this error on the non-root bridge: DOT1X_SHIM-3-PLUMB_KEY_ERR: Unable to plumb keys - Eap key struct is NULL and the bridges do not authenticate.
View 2 Replies
View Related
Apr 29, 2011
I installed NGS 2.0.2 for wireless guest user management and authentication. I implement webauth via webauth page on wlc deployed.One Branch with a WLC5508 version 7.0 wireless anchor controller is working on the NGS.But now I integrate next branch with WLC4402 version 6.0.188 and the authentication of users at the new branch gets an error, wrong user/password.
I double checked configuration and user/password but I can't find any configuration error. Also stopping and starting of radius service and reboot of NGS still does not work. I tried to debug the radius via web interface and watched for the loggfile and there is still a reject.I also tried the freeradius command radiusd -X but I got an error when starting the radiusd -X.
1.) How can I figure out, if I will get the correct password from my WLC ? Are there any debug options to see more ? e.g. some cli commands, radiustest utilities or how to get the received password from the chap challenge of the debug ?
2.) I have appended a part from my radius loggfile. How can I find the detailed error in the radius log file? Is it correct that the password in the debug file is empty ? raiuds logg line "[radius-user-auth] expand: %{User-Password} -> "
View 3 Replies
View Related
Jan 16, 2012
I configured before ACS v4.2 to authenticate network devices using internal users at first, and if the user is not found use AD list users. But with v5.3 I have some problems doing this, on identity policies I use rule based result selection option, I configured 2 polices for Identity source, one for Internal Users and other policy for AD user, but it only works with the first policy, internal users or AD, but works only for the first policy identity. how to do that, if the user is not found on first policy, continue to the next policy.
View 7 Replies
View Related
Jul 3, 2011
I need a specify users to allow access to particular devices and give privilege only for show command or show run. Here is how I tried to configured.
1. Configured two seperate Shell Profile and Command set with privilege level 4-5 and allowing only show run command
2. create seperate service selection rule with adding the require NDG and protocol TACACS and maching service "RestrictAccess"
3. In the RestrictAccess Service I have following configured; Identity: internal users, Group Mapping to a particular group where the user exists, authorization: matching the above created identity group, NDG, shell profile, command sets
All the steps are attached in the .doc file. However when I tried with the particular user he is able to access everything and he is not hitting the correct access rule.
View 6 Replies
View Related
Oct 6, 2012
I have two ACS v 5.2 (primary and secundary) and some users are in the internal stor and the others are in the AD.The local site topology is like this:
PC - AP - WLC - ACS - AD
Authentication method is PEAP(EAP-MSCHAPv2) and all user have the certificate company installed. The OS in the client users is Windows 7.Users was working fine but some users reports intranet disconnections. I see in the ACS log many "22056 Subject not found in the applicable identity store(s)." and "24415 User authentication against Active Directory failed since user's account is locked out" alarms.I believed it was because user wasn´t in the AD data base, but some times the same user is authenticated successfull and other i see the "22056...." or "24415...." alarms.
I switched the role for ACS primary to works as secundary and we see the same alarms.
View 2 Replies
View Related
Sep 17, 2008
I got a WLC4404 running software version 5.1.151.0 with 40 LWAPPs (mostly 1242AG). We got new Dell Latitude E6500 Laptops with Intel 5100 NICs. After upgrading the bios to the latest version and installing the latest wlan driver, wireless is working the most time.After about 4 reboots I see the following message in the WLCs logfile: "Thu Sep 18 13:53:10 2008 AAA Authentication Failure for UserName:host/hostname.domain.name User Type: WLAN USER".After I disable the wlan-card, it's working again.
View 7 Replies
View Related
Oct 25, 2011
I use PIX 8.0(4) and ACS 4.2 for VPN authentication. I got error as below even I'm able to ping to ACS server from PIX
RADIUS_SENT erver response timeout
RADIUS_DELETE
ERROR: Authentication Server not responding: No error
I tested aaa command from PIX and check configure on ACS (key and IP address) include restart ACS. The output still timeout and not responding from server.
PIX config:
=========
aaa-server AAA-VPN protocol radius
aaa-server AAA-VPN (MANAGEMENT) host 172.20.0.9
key xxxxxxx
tunnel-group CGS-DR type remote-access
tunnel-group CGS-DR general-attributes
address-pool VPN-POOL
authentication-server-group AAA-VPN LOCAL
default-group-policy GR-CGS
View 2 Replies
View Related
Mar 14, 2012
i received the below output,how to start a troubleshooting? the aaa server is cisco ACS 5.3
ERROR: Authentication Rejected: Unspecified.
View 1 Replies
View Related
Dec 30, 2012
I cannot connect to home WiFi while all other devices connected. Getthing "Authentication Error"
View 2 Replies
View Related
Jul 7, 2012
When I try to log-in to my D-Link DIR-835 Router using IE9, I get an 'Authentication Failed' error. FireFox & Chrome work just fine. what I need to change or fix in IE9 so it will also log-in to my router?
View 13 Replies
View Related
Dec 19, 2012
When I get the web authentication dialog from 1.1.1.1 it starts of with a certificate error. Is there a way to prevent this certificate error while using the self signed certificate? I have not been successful installing certificates on my WLC - problems with OpenSSL and others. Want to get this deployed but don't want users to have to encouter that error.
View 1 Replies
View Related
May 12, 2013
I just got a Samsung Galaxy S4. As I have always done with all of my devices that connect wirelessly, I went into the D-Link software and added my phone's MAC address to the network filter list. The security settings are WPA/WPA2. When I try to connect, the phone is able to see my Wi-Fi network, and it asks for my password, which I enter. It keeps trying to connect, but then it says an "authentication error occurred." I have checked and triple-checked the password, and it is correct. I have also checked and triple-checked the MAC address, and it is correct. I have rebooted the router and the phone several times each.
View 1 Replies
View Related
Jul 22, 2012
I have have a XPS L502X. I decided to make a clean installation based on Windows 7 Ultimate.My problem is when I instal the driver for the "Dell Wireless HSPA 5540" it fails with then warning:
"Authentication failed. The .... driver cannot be installed on this computer...."
How to install driver for this ?
View 13 Replies
View Related
Nov 6, 2011
I'm trying to set up a 5505 (running 8.3) so that i can use the client vpn through RADIUS authentication.I have set up a new local RAIDUS windows box and used the ASDM asistant and a few other guides to setup the 5505.
View 3 Replies
View Related
Dec 5, 2012
I have one Fortigate 200B Fire wall, which is using for wifi internet. i had configured one login page in the fourtigate .The path following below system > config > replacement message > authentication > login page.
it was working earlier. suddenly its not working. when i checked this path, that login page message colum was blanked. when i trying to put the message again its not pasting and am unble to type the message also.
View 3 Replies
View Related
Feb 2, 2012
In order to restrict access to websites on our internal network, would we be able to put an ASA in front of the web server and force users to authenticate through the ASA and, once authenticated, allow only port 80 or 443 traffic for that use? The ASA would query the ACS 5.1 server for authentication/authorization using AD as the identity store. Is this even possible with TACACS?
View 1 Replies
View Related
Apr 1, 2012
My customer has a large installed base of MACs, all connected via controller-based (5508) WLAN. He wants to grant access to the network based on the device's mac addresses and move the WLAN-clients to a specific VLAN.I added all devices with their mac addresses to the ACS internal identity store for hosts.According to the following message the client sends the user-login credentials (chegger) within the RADIUS-request instead of the clients mac address and of course it has to fail. After many configuration changes, I ended up always with the same result.
View 2 Replies
View Related
Jun 13, 2012
I have question on EAP-TLS with ACS 5.2. If I would like to implement the EAP-TLS with Microsoft CA, how will the machine and user authentication take place? Understand that the cert are required on both client and server end, but is this certificate ties to the machine or ties to individual user?
If ties to user, and I have a shared PC which login by few users, is that mean every user account will have their own certificates?
And every individual user will have to manually get the cert from CA? is there any other method as my environment has more than 3000 PCs.
And also if it ties to user, all user can get their cert from CA with their AD login name and password, if they bring in their own device and try to get the cert from CA, they will be able to successfully install the cert into their device right?
View 7 Replies
View Related
Jan 22, 2012
I have a new ACS 5.3 installation which I have joined to our AD Domain and added the directory groups into. I have also added all our devices into ACS and their groups etc but I am still only able to authenticate on the our switches with an internal ACS account, when I try with an external AD account the log shows the following error "Subject not found in the applicable identity Store (s)"
View 1 Replies
View Related
Apr 29, 2013
I have a device manufacture there are requesting the following change on a customer's WLC 5508.
-config advanced eap identity-request-timeout 60
-config advanced eap request-timeout 60
I have studied many guides but I can't find out if there is a down-side to setting the timeout this high.Could it result in slow roaming or re-authentication if there is a connection error? The customer have large areas with high client density and some outdoor areas with low client density.
View 3 Replies
View Related
Feb 8, 2012
I am getting the below error on my new switch though I can’t find out A. why I am getting the error and obviously B. how to resolve said error as I need to ensure I am operating under the letter of the law and compliance. The switch is a WS-C3750X-48T-S running C3750E-IPBASEK9-M, per my research IP base is the correct IOS for a T-S switch, the label on the outside of the switch matches the show ver (WS-C3750X-48T-S) so I know that IPBase is the right IOS for the hardware. Could it be that I don’t have the license file installed? Below is what I get when I do a show license. Lastly is there a place that I can find what IOS ships default with what switches, not version but type like c3750e-ipbasek9-mz.150-1.SE vs c3750e-ipbase-mz.150-1.SE
Error“%ILET-1-AUTHENTICATION_FAIL: This Switch may not have been manufactured by Cisco or with Cisco's authorization. This product may contain software that was copied in violation of Cisco's license terms. If your use of this product is the cause of a support issue, Cisco may deny operation of the product, support under your warranty or under a Cisco technical support program such as Smartnet. Please contact Cisco's Technical Assistance Center for more information.”
[code].....
View 3 Replies
View Related
Dec 9, 2012
i have a problem with 1552E to register with 5508 WLC, and always got "AAA authentication error” in the WLC log, while AAA is not enabled. so my question is , do i need to add the MAC address to the WLC MAC filter list even if i not enable the AAA server in the WLC.
View 9 Replies
View Related
Dec 30, 2012
I cannot connect Android Tablet to home WiFi. Getting Authentication Problem" as error.All other devices connected. Have tried all of the solutions on this and other sites
View 3 Replies
View Related
Apr 18, 2010
We got recently a Cisco Secure ACS 1120 and i upgraded the Appliance to 5.1 from 5.0 with all your support
Now I need to integrate Cisco ACS 5.1 with RSA Authentication Manager 6.1 . I Successfully Downloaded config file from RSA ACE Server and exported into ACS 1120.
I also Added ACS as a NetOS Agent in the RSA Server , during the process i found few warnings . The ACE Server is not able to Resolve the IP Address to NAme ( DOes it Necessary ?? ).
I havent created any secret Key file for communication between ACS and RSA and encryption i used is DES.
Now when I log into ACS and search for Devices in the Identity Store Sequences i am not able to Look for RSA Token Sever .
View 10 Replies
View Related
Nov 22, 2011
I have been trying to get our IPS (ASA-SSM-10 and 4260) to authenticate with Cisco Radius ACS 5.2 and they are not working. However, I was able to get them working with Microsoft Radius. Below is the logs from the IPS:
evStatus: eventId=1321566464942057375 vendor=Cisco originator: hostId: NACAIRVIDLAB1 appName: authentication appInstanceId: 350 time: 2011/11/23 17:50:38 2011/11/23 09:50:38 GMT-08:00 controlTransaction:
[Code].....
View 0 Replies
View Related
Dec 13, 2012
If laptop/desktop goes on sleep mode or keep connected with interface configured for 802.1X for more than 12 hours it does not work or not connect to Exchange server, Cisco ISE console, office communicator..for re authentication i need to restart PC/ Laptop or unplug and replug lan cable from it!but before restarting i am able to ping all DNS, DHCP, OCS, everything..[code]
View 6 Replies
View Related
Mar 9, 2011
I would like to konw does Cisco ACS 4.x / 5.x natively support Two factor authenication, but not act as a Radius Proxy?
View 1 Replies
View Related
Feb 23, 2012
I need to limit to some AD groups, authentication with ACS 5.3.For example, i need that only users os somedomain.com/users/test1 are authenticatet via ACS --> ADS.
View 1 Replies
View Related
Mar 4, 2012
I have a Cisco ASA (8.2) setup with remote access for my users using Cisco VPN client. The authentication is passed off to my ACS 5.3 which then checks with AD. What I've done so far is create Access Policy rule where I define specifically the Location and NDG where the ASA is and then a DenyAllCommands command set. This should pass authentications just fine but this also gives those users the ability to remote connect directly into the ASA and login successfully. Even though there is a Deny Commands there I still would prefer they get Access Denied as a message. If I do a Deny Access on the ShellProfile then this stops the login authentication altogether.
View 2 Replies
View Related
