Cisco AAA/Identity/Nac :: Specific Targets Not Receiving Syslog Traffic From ACS 5.3
May 9, 2013
We have a distributed ACS 5.3 set up - a PR and DR replicating successfully.I've set up 4 remote syslog targets. 2 of them are at the same site as the PR ACS and 2 are at the same site as the DR ACS.The logging collector is set on the PR ACS.
The problem is that it "appears" that PR ACS is only sending PR ACS syslog info to one of the remote syslog targets out of the four.
The syslog target which does receive from the PR ACS is at the same site as the PR ACS.
"appears" means that some one has looked on the syslog targets to see what's been received / or not received.
I've been told that the syslog traffic for syslog targets is being received from the DR ACS. Which is strange as the PR ACS is the actual log collector (and is not at the same site as the DR ACS).
I've also got Alarm Syslog targets set up on the PR ACS , (2 are the same ip addresses used in the 4 remote syslog targets). IP addresses of the remote syslog targets have been double checked and can be pinged from each ACS (PR and DR).
View 5 Replies
ADVERTISEMENT
Mar 19, 2012
I have configured the appliance everything is working fine.We have a remote syslog server and I have configured the remote syslog server details in the "Remote Log Targets" and and Logging Categories.But I cannot see any logs on my syslog server
View 4 Replies
View Related
Aug 8, 2012
Cisco ASA 5510. Between 5 to 10 minutes of reseting the asa traffic stop accessing outside ip addresses. Ping from console fails to ISP router IP. Ping to google name server failes. I have reset to factory default only setting up nic and natting and it still happens.
View 2 Replies
View Related
Jul 3, 2012
We run a Cisco ASA 5510 and i need to find out how i can find the receving end on the inside of a vlan for traffic comming from outside.
ie incomming traffic on port 3937 and are NAT to eth 0/1.10
Thers a bunch of traffic on one port 33771 udp going in on 90.191.72.227 how do i trace this to the inside computer ???
lets say incomming traffic is on 90.191.72.227 and this is on eth0/0 this ip is NAT to a Vlan on the side for 10.10.0.0 with a subnet of 255.255.255.0
View 1 Replies
View Related
Jul 19, 2012
We are using version 5.3 with patch 5. Incremental and full backup are configured but every day we receive an alarm notification.
View 7 Replies
View Related
Dec 11, 2011
I have configured ACS 5.1 and using Tacacs. I have two juniper SSG140 FW's in different subnet. Tacacs authentication is working on one SSG140 FW, but not on the other one. Tacacs configuration on both FW's are exactly the same. Both FW's have been added in the ACS server with the same shared secret key same profile etc. I don't even see the authentication requests from the FW. ACS can ping both FW's and vice versa. [code]
View 2 Replies
View Related
Feb 18, 2012
I want send ACS logs to a syslog server .I have configured syslog under System Administration --> Configuration -->Remote Log Targets .
Name : Syslog Server
IP : x.x.x.x
Port : 514
Facility Code:Local 6
Maximum length :1024
I have open the respective ports also in firewall .But Syslog server is not getting any logs from ACS .I have another log target ,which is ACS secondary server to collect the log from primary and secondary with below config.whch is working fine
Name :Logcollector
IP : x.x.x.x
Port : 20514
Facility Code:Local 6
Maximum length :1024
View 7 Replies
View Related
Dec 12, 2011
I am sending TACACS administration logging to a syslog server. When the messages show up on the syslog server, they are 5 hours ahead of the actual time. Time on the ACS is correct - local logging shows the correct time. Time on the syslog server is correct...all other devices/systems sending syslog messages to it are coming through with the correct time. why the ACS syslog messages would be 5 hours ahead?
View 3 Replies
View Related
Dec 4, 2011
how can I configure ACS 5.2 to send syslog messages to CS-MARS?
View 3 Replies
View Related
Jul 7, 2011
I have two ethernet adaptors on my windows machine. OS is Win-XP.I am running ADSL broadband on LAN1 and on LAN2 I am accessing applications on our company's WAN. LAN1 is on 192.168.1.0/24 subnet and LAN2 is on 10.68.104.0/22 subnet.Accessing application through LAN2 involves DNS that is located distantly, therefore routers are also in picture.Problem is that while accessing the application that run on the network of LAN2, I have to disable LAN1. Otherwise the traffic goes on LAN1.
View 2 Replies
View Related
Oct 14, 2011
My question is pretty straight forward but here is some background information. I would like my browsing traffic to funnel through my phone's 3G or WiFi connection. Is there any information out there on how to direct the browser to use the second internet connection? I was thinking about setting up a VPN using the second nic and somehow instruct the browser to use the specific proxy. I have no idea if that is even possible though.
The need for this is pretty simple. I do not want my browsing habits being logged by my company's network. Also while maintaining the current corporate connection so Outlook and RDP programs continue to function correctly.
View 1 Replies
View Related
May 20, 2012
I have a number of sites in China, they have decent inter-country connectivity but poor connectivity when going overseas.
We have a single site in China witha dedicated 1:1 leased line that has good conectivity both inside and outside of China.
All the sites in China have ASA5505 firewalls
One of our Citrix farms is hosted in the UK and although the main site with the leased line is fine accessing the farm the other sites are not. I would like to try and tunnel just the citrix connectivity via a VPN to the China head office then use their connection to get out to the farm.
how to tunnel all traffic but not just specific traffic over the VPN.
View 3 Replies
View Related
Mar 16, 2013
I have ASA 5510 8.4 Firewall where more than 20 Site to Site VPN Clients are configured on it. how to see the traffic for one Specific Site to Site VPN.Actually this site to site vpn is always keep dropping for every minute. I'm sure its a problem at the other end.The remaining 19 VPNS are UP and working without any problem. How to see the traffic for specific vlan.More over we dont have any syslog server in our network. Is their any chance we can check the traffic on the firewall?
View 6 Replies
View Related
Mar 6, 2012
How to force traffic back out the same interface from whence it entered. Review the following topology.
Internet ---> ASA 5510 ---> Static IP1 ---> F3.1 ---> 1811 F0
|-------> Static IP2 ---> F3.2 ---> 1811 F5 ---> VLAN Int
ASA F3.1 10.1.254.9/30
ASA F3.2 10.1.254.13/30
1811 F0 10.1.254.10/30
1811 F5 10.254.1.14/30
When pinging the public IP of ASA F3.2 from the internet a reply is never received because the default route on the 1811 points to ASA F3.1.
How do I get the replies from the 1811 to go back out the same interface from whence it entered ? I am sure the answer is policy-based routing, but not sure how to write the config.
View 1 Replies
View Related
Oct 5, 2011
How to configure the 825 to block inbound traffic from a specific internet IP address ?i noticed an IP and MAC that i don't recognize that is listed as a connection to my NAS's media server ...i blocked it in the NAS configuration page, but i don't want any unsolicited traffic into my network.
View 3 Replies
View Related
Jul 7, 2012
Add the ability to send syslog events to multiple syslog servers in the SA500 Series routers. I know the functionality is currently in the RV220W because we utilized it. It would be great if you could configure the syslog servers by event type as well. For example, being able to send the kernel events to syslog server A, and all other events to syslog server B.
View 0 Replies
View Related
Jan 15, 2012
Recently i have upgraded the IOS of ASA5550 (in HA mode) to 8.4.2 from 8.0.5, after OS upgrade we found that the syslog from thses firewalls are not getting captured/transfered to centralised syslog server. The server is reachable from the firewalls.
View 3 Replies
View Related
Oct 10, 2012
Have a quick question regarding inter-vlan routing on a 3750. Overview of network is ISP --> ASA --> 3750 (acting as my core and default gw). I have 5 vlan interfaces on my 3750, all w/ 192.192.x.x subnets, a 6th w/ 192.168.100.x, and a 7th w/ 192.168.200.x. I have enabled "ip routing" on the switch and can successfully ping from subnet A to subnet B as long as both devices are using the correct DG for their vlan, which is the switch. I have a few ports that are trunked as well that go to ESX hosts which break out the vlans according to the subnet the vm should be attached to. The ASA is set to nat internal traffic for all the vlans.
Now my question: short of applying an ACL to each vlan interface to block traffic from other 192.192.x.x subnets is there a better way to accomplish this? I want my 192.168.10.x subnet to be able to reach all the subnets, but don't want 192.192.10.x to be able to talk to 192.192.20.x for example. I was thinking to create an acl like this:
access-list 120 permit ip 192.192.10.0 0.0.0.255 access-list 120 deny ip 192.192.0.0 0.0.255.255 192.192.10.0 0.0.0.255access-list 120 permit ip any 192.168.100.0 0.0.0.255 192.192.10.0 0.0.0.255
and then applying this to the interface for the appropriate vlan.
View 4 Replies
View Related
Aug 1, 2012
I have an RV042. I understand and have created the services I need. The documentation is just not clear on how to direct traffic for these services to a specific wan port.
Can this even be done with this router? If so, the how? Use rate control or priority? Does checking a wan port mean that it will only go through that port?
View 4 Replies
View Related
Jun 1, 2011
I'm trying to route all default traffic from my production environment through my ASA 5520 on the "outside2" interface.The 5520 has a site to site VPN to our DR site on the "outside/inside" interfaces via one ISP. On another ISP, interfaces "outside2/inside2" go to the internet.
When I make my 3750 stack default route for the inside2 interface IP I cannot get to the internet. When it is pointed to the inside interface on my 5505, I can.
I get the following errors when I try to open google.com from a production server:Why is the 5520 trying to use the "outside" interface instead of the "outside2" interface to go out?
View 6 Replies
View Related
Feb 5, 2013
I am trying to find a tool that will monitor the web traffic for one specific user. If it is capable of bundling it into a report that would also be a benefit. I have searched, but not come up with much aside from broad network monitoring tools. All that is really needed is to capture all the activity from http traffic for this one specific user/PC (since she uses the same PC all the time). We have a Sonicwall NSA 2400 as our internet filter, but I was not able to locate anything on there for specific user reporting.
View 2 Replies
View Related
Sep 24, 2012
I inherited a Cisco ASA 5505 and am trying to piggy back the device off of an established Network. Here is the basic layout:
192.168.10.1 (Core Router - Handles DHCP/DNS)
192.168.10.9 (ASA 5505 - Piggy backing off of Network)
192.168.40.x (ASA 5505 - VLAN)
I'm able to get onto the Internet without any problems. Devices from the 192.168.10x Network can not ping the inside VLAN1 (192.168.40.x). However, I would like traffic going from the inside VLAN to the Outside VLAN to be blocked, except for 192.168.10.1 and 192.168.10.9. I've tried using ACL's but end up killing my Internet connection. 192.168.10.1 is the default route and is how I get out to the Internet. Is this possible? Essentially, I'm trying to set up a small Network that guests can connect to. The idea is that they can get to the Internet, but that is it. They can't get to internal resources on the 192.168.10.x Network
Here is the config:
ASA Version 8.2(1)
!
hostname ciscoasa
enable password EeCsulrpu.9LalEE encrypted
[Code].....
View 5 Replies
View Related
Jan 18, 2010
I want to redirect internal web traffic (browsing) to an external web server for Web, Virus and Spyware filtering. Those externals proxies are running in 8080 port. I have one ASA firewall and a Cisco 2600 router. I was thinking in doing PBR in the router but in the next hop I can only set one IP, not an IP and a port. So how can I redirect web traffic to an external proxy listening in 8080 port?
View 11 Replies
View Related
Jul 22, 2012
Is it possible for ACS 5.1 to only allow specific AD users to authenticate the switches and routers? Currently What I have configured is only for all AD users. I can't seem to find a way to be selective.
View 9 Replies
View Related
Jun 25, 2012
on the acs 5.2 , how to delete specific log for user X, ?
View 3 Replies
View Related
Nov 4, 2012
I've configured three specific AD groups, Admin, Storage, and HelpDesk, with their own commands sets.
This seems to be working fine, but everyone can log into everything, but they can't do anything except exit.
My goal is to not allow anyone to login that is not part of the three AD groups I have specified with the respective command sets.
All the logins hit the Admin account, even though the id in AD is not in the that AD group. I have something screwed up.
View 6 Replies
View Related
Nov 15, 2011
How does a firewall block or filter traffic on a specific port or IP address?
View 1 Replies
View Related
Jul 25, 2011
if the firewall rules in the RVL200 work for inter LAN routing as well as LAN<->WAN? I need 2 separate networks in a house, 1 for business 1 for family, and I want to only allow my IP on network 1 (family net,10.0.0.0/24) access to network 2 (business net 10.0.1.0/24). I want this as if I change rooms were a access point for business is not available I can use the home net and specific IP to access certain business net IPs. I saw you can turn inter vlan routing on or off, but it wasn't clear on firewall rules.know of a similar router in cost but with gige instead of 100Mb ports?
View 1 Replies
View Related
May 16, 2011
I'd like to know if there is a way to exclude passed authentications for a specific username from reporting in the Authentications-TACACS and Authentications-RADIUS reports?
We have a few usernames that are used in scheduled jobs. We only need to know when they fail authentication, so we don't need to fill up the reports with every passed authentication from these accounts. Can this be done?
View 1 Replies
View Related
Mar 28, 2011
I am doing MAB (MAC authentication bypass) for IP phones and printers.
But these devices are authenticated with different identity stores (IP phones with AD, printer local host on ACS)
Is there any specific AV Radius attributes that i can use in the compound conditions selections which is specific for the IP Phones?
so when doing the Authentication, i could seperate each type (IP phones or Printers) with the appropriate database.
View 1 Replies
View Related
Feb 21, 2005
I'm using Cisco ACS 3.3 for RADIUS. How to do I make Vendor-Specific attribute available? (Attribute number 26, format: OctetString) The online help makes reference to it, but does not tell you how to make it available.
View 9 Replies
View Related
Feb 16, 2012
I am facing problem with ACE configuration. I want to redirect 443 traffic to my Proxy Server. But I am not able to do this. I want to redirect only subnet 192.168.80.0/24..Then only it is working but I dont have to have this policy to be applied on all the users only one subnet I want to have under HTTPS policy.
how can I apply the policy only on specific subnet so that port 443 traffic can be redirect and rest of all subnets can go direclty to Internet.
View 8 Replies
View Related
Nov 2, 2011
Is it possible to configure the span(switch port analyzer) port and restrict it to only listen to ingress and egress of TCP/1433 from the source port?
View 2 Replies
View Related
