Am having 2621 router, going to upgrade to gh speed wan interface card(HWIC-4ESW). whether it can able to handle routing as like a normal serial and ethernet interface? Shall i establish a new MPLS or Leased line connectivity in that interface(HWIC-4ESW) ?
View 5 RepliesI have P router (7206VXR) and I need to export netflow from its MPLS interfaces to the netflow software.
View 2 Replies View Relatedi try to Access ACS5.2 installed on VM via SSH. I used 3 different SSH Clients, Teraterm, Sec CRT and Putty, all failed. Putty failed after (correct) password, Teraterm and SCRT failed with a Popup and the List of ACS Supported Modes (DH Group 14, AESxxxCBC ...). I configured them in the Options, but failed again.
View 3 Replies View RelatedI'm trying to establish a BGP neighborship with my ISP using my own ASN. The thing is that AS is a 32bit AS. I read on others papers that since the IOS 12.4(24) the support for ASN 4byte(32bits) was introduced. For some reason I cant enable BGP under an AS32bits on my 2811.
Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(24)T1, RELEASE SOFTWARE (fc3)
BGP-AS32(config)#router bgp ?
<1-65535> Autonomous system number --> Only 16bits
<1.0-XX.YY> 4 Octets Autonomous system number
BGP-AS32(config)#router bgp 262477
^
% Invalid input detected at '^' marker
I am having an issue with a VPN tunnel in that we can only establish this from the VPN 3k side to the 2800 and not from the 2800 to the VPN 3k , the setup is as follows: [code] I am awaiting the logs from the VPN 3k but here is the debugs from the 2800. [code]
View 4 Replies View Relatedhow to establish a LAN connection in windows7, am facing a problem ie. i couldn't ping my own IP.
View 3 Replies View RelatedI want to establish a key for my computor to preclude neighbors from using my system. How?
View 1 Replies View RelatedI want to establish VPN with GRE over IPsec. As ASA can't end GRE tunnels, I should pass it through inside to another 1841 router in datacentar network. Since datacentar is connected to internet via two wan links (separate ISPs) is it possible to establish two gre simultanous sessions between 1841 at branch office and 1841 at datacentar, one session per wan link at datacentar? That way, I need 8 gre separate sessions (tunnels) at datacentar 1841 router. Is it supported?Is GRE passthrough works like regular port forwarding or it is something that ASA handles with some special commands?
View 1 Replies View RelatedI have installed and setup cisco anyconnect on a win2008 server. It is able to authenticate successfully but upon trying to establish the vpn connection to the asa5520, it shows "unable to establish vpn". Other servers and pc from the same remote site is able to establish the vpn.
View 1 Replies View RelatedJust like to ask first your inputs about the MTUs needed on our proposed setup. We currently have a large internal network composed of several metro ethernet links. We have different carriers and we all know that they do not always provide L1 connectivity. They sometimes do Q-in-Q or EoMPLS or other technologies that would hide their internal network and appear as a point-to-point ME circuit to customers.
We are planning to create our own MPLS network for our clients so we don't have to leak their networks inside ours and we are trying to avoid the overhead of GRE/IPSEC since we'll be adding a lot of client networks and the overhead is not reasonable. So we just thought of MPLS-VPN to at least reduce the overhead and we don't have to purchase a lot of network devices.
With that said, what is the safest thing to ask the carriers and what settings should i put in our network devices. I am still confused with the differences of MTU, IP MTU, and MPLS MTU.
We also have one circuit running 802.1q instead of using routed-port on the switch. Is 802.1q supported in LDP?
Our internal network is comprised of 6500 switches with Sup720 and Gigabit linecards and we are planning to use 3900 routers as PEs. We all hooked up our ME circuits across the 6500 switches.
tell me the IOS (c2600-???) needed to be able to do MPLS on the 2621 XM router?
View 2 Replies View RelatedOn my PC laptop, when we try to connect to the internet (wireless router) through firefox we get the error message"Firefox can't establish a connection to the server @ cn-us.start3.monzilla.com. When we try using Window explorer we get "Internet Explorer can't display webpage" When prompted to click on "diagnose connection problem" it states Windows did not find any problems with this computer network connection.
A couple of points... the connection indication at the bottom states the laptop is connected to the internet. (WLAN ON)I have a Mac that is connected to our internet and doesn't have any problems.We have Windows Vista on the PC laptop
I too am having a problem establishing a secure connection for Dropbox, Adobe update and just about every website I try to access via Firefox or Chrome comes up as unsecure. I can add exceptions, but I would rather access them securely.
View 3 Replies View RelatedI have tried to establish a VPN-Connection from Ipad (via the Ipad built-in vpn-client) to a SA540.Unfortunately without any results. I get the message "Server is not responding". (A VPN Connection from a normal Software-Client running on W7 works fine).
View 0 Replies View RelatedI am facing problem when trying to establish VPN connection between ASA and 1841 router. Peer comes up but traffic is encrypt and decrypt. when assign route (ip route 192.168.x.0 255.255.255.0 fa0/0) to remote local subnet there is a traffic but one reply and one drop
ping from
192.168.y.62
-------------------------------------------------
Reply from 192.168.x.55: bytes=32 time=493ms TTL=127Request timed out.Reply from 192.168.x.55: bytes=32 time=633ms TTL=127Request timed out.Reply from 192.168.x.55: bytes=32 time=375ms TTL=127Request timed out.Reply from 192.168.x.55: bytes=32 time=528ms TTL=127Request timed out.
[code].....
I´m getting a dynamic public IP from my provider and what I´m trying to do is to establish a remote vpn tunnnel using IPSec which I achieve but every time the sessions resets or the ASA 5505 resets I get a new public IP and I need to put the new IP on the remote client so I can establish the vpn... How can I establish an ipsec vpn using DNS? For this scenario the remote vpn client is a vpn phone but it could be for any vpn client.
Private IP Public IP Private IP
PBX ---- (LAN) ---- ASA 5505 ---( Internet ) --- Remote Site ( Router ) --- (LAN) -- VPN Phone
Something seemingly so simple is not working. A router and a Nexus are not seeing each other via CDP. I have a 2921 router connected to a Nexus 7000. Everything works fine, except for some mysterious reason CDP does not establish. Yes, it is enabled on both devices and not disabled on the relevant interfaces. The Nexus says this over and over again when debugging cdp errors:
[code]....
I have successfully connected two RV042s to establish a VPN gateway to VPN gateway connection. I have the follow questions:
1. I would like to keep the VPN tunnel connection time indefinite. Is it sufficient by checking the "Keep-Alive" box on the VPN -> Gateway To Gateway -> Advance page? Or, I have to ping the RV042 periodically?
2. Do the "Phase 1/Phase 2 SA Life Time" (on VPN -> Gateway To Gateway page) settings have any impact on keeping the VPN connection time indefinite? What are the optimal values for them?
3. Is there an API, command, or script to replace a manual clicking on the "CONNECT" button to establish the VPN tunnel from the VPN -> Summary page? Or, is there a way to accomplish this at power up?
4. Is there a way to establish a VPN tunnel without going through login and clicking the "CONNECT" button? (Auto connect at power up?)
I have remote branches that connect to the corporate office as a site-to-site VPN. Now the clients at the branch are getting an application that is using an unsecured port (tcp/23). I would like to use a set of ASA 5520's that I have at the corporate office, with the AnyConnect license on them. I want the client machines to establish a tunnel from the client to one of these ASA's. The ASA' then would have a connection to the VLAN that the receiving server is housed on. The trick is to just establish the tunnel from the client to the ASA that will allow the IP of the client to not be translated. So I would use the ASA as a security 'pass-through' for the clients that use this new application.
View 1 Replies View RelatedIphone 4S latest IOS5 V 5.1.1 installed?I'm not able to make native IPSEC VPN connection to work against my company Cisco 877 Instead, all my notebook and netbook with Cisco VPN Client installed work fine when they remotely connect to company's 877 Enabling 877 debug, it seems Iphone successfully pass the phase 1 ike connection (in fact Iphone asks me for phase2 user/pass) but it hung at phase2 giving me back the error "Negotiation with VPN server failed"
Here is how I configured my 877 VPN part :
R1(config)# aaa new-model
R1(config)# aaa authentication login default local
R1(config)# aaa authentication login vpn_xauth_ml_1 local
R1(config)# aaa authentication login sslvpn local
R1(config)# aaa authorization network vpn_group_ml_1 local
R1(config)# aaa session-id common
[code]....
It seems 877 even comes to allocate a local LAN ip address to Iphone (192.168.0.21) but then something goes wrong.....
I have a RV042 and want to establish one WAN connection via PPPoE. I enter Username and Password, Keep Alive, MTU=Auto. The router does not get an IP address (0.0.0.0) and the log says: "[pppoe] sending PADI", "last message repeated 5 times". What is confusing me is that a PC connected to the RV042 (and a DSL-Router operating in Modem-Mode "PPPoE Pass-Through") can establish a PPPoE connection with the same Username and Password. Why can the PC connect via PPPoE, but the RV042 can not?
View 4 Replies View RelatedWe're looking at rolling out MPLS between each of our sites. probably more soon.Do you guys have favorite MPLS providers? How have your experiences been?
View 10 Replies View RelatedWhat is the purpose VPN label?As we know, in the MPLS VPN, the following mechanisms:RD - used to distinguish between overlapping routesRT - used to determine the VRF in which to send the route.But why need a VPN label?
View 11 Replies View Relatedthere is a line set with a provider with EoMPLS.This is an international line coming with 10M connectivity.the line is working fine with udp traffic but with tcp we don t get any use more than 1M.
View 7 Replies View RelatedConfiguring MPLS over GRE tunnels. I did not find any proper configuration example. I need to do this for encrypt the traffic between two PE routers. I have 7609 routers.
View 20 Replies View RelatedI currently have a 150 nodes MPLS network. My management is anxious to join some sites with 3G routers as their centres move around a lot.My current MPLS site as 4 x Ps with lots of PEs linking to the 150 x CEs. Is there a way to easily link up my 3G routers to my MPLS network? I have heard DMVPN may be a solution, but not sure how to implement.
View 4 Replies View RelatedRecently i purchased Cisco 861-K9 router for my head office.
I have 2 offices (1 is head-office & other is Branch.). i have MPLS Connectivity between 2 offices.
i used 861-K9 WAN port for MPLS Connection.
My question is "is it possible to use the FastEthernet Port of 861-K9 router for connecting the internet Link ?"
I've got a 6509-E in the lab at the moment for some pre-deployment testing, however I don't seem to be able to enable MPLS on a select interface.
router#conf t
router(config)# interface gi1/48
router(config-if)#mpls ip
router(config)#
As you can see after I enter the "MPLS IP" command it simply backs out of interface level configuration back to global exec, and naturally the MPLS command doesn't show in configuration for that interface.
I'm running a SUP720-3BXL with WS-X6748-GE-TX line cards with the DFC upgrade (WS-F6700-3BXL).
The IOS is: s72033-adventerprisek9_wan-mz.122-33.SXI2a.bin
i wanted to know if i can and when i will be able to run the nexus 7000 as a Fully MPLS PE router (L2VPN, L3VPN etc..) ?
the interfeces need to be 10Gbps so i need to use the 8 ports & the 32 ports M1 modules.
I have done a bunch of research in trying to re-use an old card/router for testing our new MPLS link. I have a 45m DS3 and was wondering if the PA-MC-T3= card will work UN-channelized. I have tried the "no channelized" command under the controller to no avail. I believe that the card only works for channelized T1's.
View 1 Replies View RelatedI connected my home laptop to the work network to download some (legal) software (by cable) but it didn't work. When I detached it the internet access to the desktop machine was not functioning. That was diagnosed as a problem with the I.P. address (presumably when i attached my laptop.) It was fixed over the phone through a START>RUN>CMd>config process. Now I find that my laptop won't connect to my NetGear home link (also cable) and wonder if the same problem might be happening, that connecting the laptop to the work network has scrambled it's recognition of the server or the I.P. address.I tried updating Kaspersky 2011 databases but it just keeps saying 'source not found'Another laptop using the same router connects perfectly each time.
View 2 Replies View Relatedi m working on a project called networked control of inverted pendulum, how to establish a network with sensor node, actuator node and controller node, in a microcontroller board ?? which board one can use for a beginner on networking!
View 2 Replies View RelatedI have spent a couple of hours to find an easy way to connect my old laptop with Windows XP with my new notebook running Windows 7. I have obtained a little bit of background information but am lost in the WWW.
I now know that I would need a special USB cable or a cross-over ethernet cable for a wired connection. As I don't have either at the moment I looked into creating a ad-hoc WiFi network between both computers. I found instructions how to set one up under Win XP and another one for Win 7 but I have found no information whether and how I can actually connect both. I reckon that I only need to set one up on one computer and then would have to somehow make the other computer detect and join that network.