Cisco Routers :: Site To Site VPN ASA 5510 And RV220W
Jan 9, 2012
I'm looking to get a remote office RV220W connected to my ASA5510. I have several PIX 501 and ASA5505's connected to the ASA5510.
I've setup everything similar that I can think of though I'm still not connecting.
IKE Policy:
Direction: Initiator
Exchange mode: Aggressive (for using FQDN Ident)
Remotes are all DHCP, so setup Local Identifier on RV220W as FQDN and typed in a FQDN for the remote RV220W. That is the same name I used for the Tunnel-Group on the ASA. Remote is IP, ASA is setup to send IP for Ident.
IKE SA:
3DES, SHA, DH2, 28800
VPN Policy:
Auto Policy, Remote Endpoint IP
[Code]....
View 3 Replies
ADVERTISEMENT
Dec 18, 2011
Can I use a single Public IP address for both Internet access and site to site vpn access?If not, can I configure the RV220W as a bridge and still use it via another gateway configured for vpn passthrough as a VPN appliance/server on the LAN?
View 3 Replies
View Related
Dec 23, 2011
I have two Cisco RV220W routers and I would like to realy DHCP from the home office to the remote office accross the IPsec Tunnel. Is this possible and if so how?
I have already gone into the IPv4 LAN (Local Network) settings on the remote router and set the DHCP mode to "DHCP Relay" providing the internal ip address of the home office router as the remote DHCP server.
View 1 Replies
View Related
Jul 22, 2012
I have a site to site VPN tunnel configured between a rv220w and rv180. Everything works fine going from site to site on LAN connections. I'm now trying to tie in the remote site wireless (rv220w side) by pointing radius to my ACS server which is on the other side of the site-to-site tunnel but it seems as though it doesnt route across the site to site tunnel. If i put a radius server on the local lan on the remote site that authentication works fine. I have confirmed there are no ACL problems. the RV220W capable of using a radius server across the vpn tunnel?
View 1 Replies
View Related
Apr 3, 2012
I have been asked to setup a site to site vpn to connect two remote offices.We have two ASA 5510's, one on each side.I can get the two ASA's setup and setup the VPN and have everything work like it is suppose to. Traffic passing from local network to remote network.
However, I have been asked to add two secure routers to the setup. One secure router between the local network and the ASA, and the other the same on the other end, between the remote network and it's ASA
Essentially, just like this:
LAN---------------------Router-------------------------ASA----------------ISP-----------ASA-------------------------Router---------------------------LAN
192.168.1.x (inside 192.168.1.1) (inside 10.0.1.1) (inside 10.0.2.1) (inside 192.168.2.1) 192.168.2.x
(outside 10.0.1.2) (outside public ip) (outside public ip) (outside 10.0.2.2)
I don't understand how this is suppose to work. I can get each side configured so that the clients on the inside can get out to the internet.A local client using the inside interface of the router as the gateway, the router then sends by route this traffic to the ASA's inside interface which then forwards the traffic to the default route/gateway of the ASA to the ISP gateway out to the internet.However, when I am thinking about the VPN I don't understand how it is suppose to work. Because the LAN address get's translated to the outside address of the Router which is 10.0.0.2, so that it goes to the ASA inside address 10.0.0.1. If I were to ping an ip address of the other LAN, it shows up as coming from 10.0.0.2 which wouldn't be part of the VPN traffic, since the VPN traffic is the local addresses as it was setup with just the two ASA's. I don't see changing the VPN traffic to the 10.0.0.0 network working because the clients on the remote network have 192.168.2.x addresses. While the ASA and router can translate from 192.168.1.x to 10.0.1.2 to the internet and back will work, I don't see requesting a connection to 192.168.2.x from 192.168.1.x working).if it matters, one router is a cisco 1841, and the other an hp 7102dl.I don't really understand why, but they just want to have the routers used in the setup. Whether it is on the inside or outside of the ASA, it doesn't matter.
View 9 Replies
View Related
Feb 16, 2013
I am trying to establish a site to site VPN with a RV180 connecting back to a corporate Network using an ASA 5510. I have the RV180 setup with the Remote IP setting and a FQDN all setup and I am able to tracert back to the ASA but I wanted to know if I have to modify anything on the ASA side and how do I setup a pre-share key to establish the secure connection.
View 1 Replies
View Related
May 18, 2012
I have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.
View 2 Replies
View Related
Jan 13, 2012
I have recently bought two CISCO routers RV220W for our main and brach office mainly for VPN tunneling. I didnt know they are routers only not modems. so I have set it up using BT 2wire Router as modem only.
I have successfuly setup the routers and manage to establish the VPN tunneling between two routers. AS bt doesnt give static WAN IP address so I have used Dyndns which works fine. although I have 5 static ip address which cannot be used for WAN unless i cahnge to one IP address even then BT tech said it will not work.
when I created the tunnel i could ping both servers with their IP only not with the names. I can ping them fine locally. I could also see the network from branch office to main office but not from main office to branch office. today when I restarted the server I cannot ping both server i mean vice versa but VPN tunnel is established. now I cannot see the network from branch office to main office as well.
Both sites running windows server 2008 standard. main office server has 6 NIC cards two wwith public and three with private ip addresses, its also runing Terminal server, exchange, file etc. the branch office has two NIC card one with private and one with public ip. Intially I could establish the VPN tunnel as the network range was same on both sites so I changed one in th e10.0.0.0 range other in 192.168.1.0 range and VPN tunnel was established straightaway.
As soon as the VPN tunnel was created I manage to creat an external trust without any problems and both servers are added in each other forward zones as name servers.
in the main office the fues went off and I had to re-start the router and now the VPN tunnel is not establishing, mainly the error is ISAKMP-SA Expired I will paste the log of both routers below
1. How to Clear Old or Existing Security Associations (Tunnels) on RV220W
2. how to fix the problem where I can ping the server with their IP as well as domain names ?
3. how to set it up so that both sides can see the network resources as well as access it ?
4. how to set it up so if the staff in branch office wants to log on the domain in main office he can simply do it as he does it in his office.
View 7 Replies
View Related
Jun 1, 2012
For the purpose of a remote backup between 2 QNAP NAS devices, I have setup a site to site VPN using 2 Cisco RV220W routers. Although VPN connects just fine, I can only access Network B from network A, but not the other way around. I believe it could be related to ip ranges/subnets.IPSec VPN connects successfully (IPSec SA Established)From network A I can connect to any device on network B (qnap smb, ssh, cisco web interface, printer, laptops, etc)From network B, I can ping any device on network A, I can access the cisco web interface from network A, and nothing else. If I try to access the web interface for the qnap on network A from a device in network B, no luck, it seems to hang. I also tried issuing a wget command from the qnap (ssh) on network B to fetch the web interface of the qnap on network A, and it says connected, but then hangs. I've tried lots of different settings (creating static routes, dynamic routes, changing subnets, etc), but without any luck.
View 0 Replies
View Related
Sep 3, 2012
I'm trying to establish a site to site VPN using ipsec between an RV220W in the UK and an RV042 in Italy to no avail.The RV042 tells me it's "waiting for a connection" and it gives 0.0.0.0 as the remote address (i'm using Dynamic addressing at both ends). I can ping the remote address with a response.The basic parameters I'm using is 3DES with SHA1, but the RV042 offers an option for Perfect Forward Secrecy which the RV220W does not (I've tried toggling this) and the RV220W offers and Extended Authentication mode which I can't see on the RV042.
View 2 Replies
View Related
Sep 12, 2011
I configurated Ipsec vpn at asa 5510. my inside ip 192.168.10.156my public ip: 85.x.x.xmy peer ip : 62.x.x.x
the project is that:
the remote site want the interesting traffic like that:
source ip 172.16.1.104 can access destination ip 10.0.154.27
My inside ip is 192.168.10.0/0 and i can not to change it 172.16.1.0/24 and i can not to add this ip at my network.
View 3 Replies
View Related
Mar 6, 2013
Our Headquarter (asa 5510) is running a site to site vpn connection with a Branch office (router 2811). All remote users are accesing the internet through the VPN and also accesing headquarter file servers.I want to know if there is a way for some remote users to be able to use the vpn for accesing the file servers but to access the internet through the branch office. The rest of the remote users will be still accessing the internet through VPN.
View 2 Replies
View Related
Apr 22, 2012
I've setup a site to site vpn on an ASA 5510 using ASDM (as I have many times before) and the tunnel appears to be up but I am not able to pass traffic. When I run the packet tracer from my inside network to the remote destination network, it shows that it is blocked by the implicit deny ip any any rule on my inside incoming access list.
View 5 Replies
View Related
Jul 15, 2012
we have two ASA 5510s one in 8.4(4) and one in 8.2(5) in a site-to-site VPN setup. All internal traffic is working smoothly.Site/Subnet A: 192.160.0.0 - local (8.4(4)) Site/Subnet B: 192.260.0.0 - remote (8.2(5)) VPN Users: 192.160.40.0 - assigned by ASA When you VPN into the network, all traffic hits Site A, and everything on subnet A is accessible.
Site B however, is completely inaccessible for VPN users. All machines on subnet B, the firewall itself, etc... is not reachable by ping or otherwise.There are also some weird NAT rules that I am not happy with that were created after I upgraded Site A ASA to 8.4
Site A internal: 192.160.x.x External: 55.55.555.201(main)/202(mail)
Site B (over site-to-site) is 192.260.x.x External: 66.66.666.54(all)
I pretty much just have the basic NAT rules for VPN, Email, Internet and the site-to-site.What do I need to add for the VPN to be able to access the site-to-site network?
Here is my NAT config:
nat (inside,Outside) source static DOMAIN_LOCAL DOMAIN_LOCAL destination static VPN_Network VPN_Network no-proxy-arp route-lookup
nat (inside,Outside) source static DOMAIN_LOCAL DOMAIN_LOCAL destination static DOMAIN_REMOTE DOMAIN_REMOTE no-proxy-arp route-lookup
!
object network DMZ_Network
nat (DMZ,Outside) dynamic interface
object network DOMAIN_LOCAL
[code]....
View 3 Replies
View Related
Jul 21, 2011
I setup RA-VPN under local asa 5510 IP pool (192.168.127.0/24) and all was working fine. I got internet and local network access.
Then i have 5 site to site VPN working fine but when im traying to access to those L2L VPNs from the remote acces client im not able to do that. So after that i decided to obtain IP addresses from my DHCP server so i can obtain IPs from my local network (172.17.16.0/16) and then access normally to the VPN site to site. But the surprise was that the VPN cisco client is getting local IP address (172.17.16.222) perfectly but im not able to access even to my local network.
I have the same-security-traffic permit inter-interface same-security-traffic permit intra-interface enable.
View 6 Replies
View Related
Mar 9, 2011
I am try to configure ASA 5510 with 8.3 IOS version.My internal users are 192.168.2.0/24 and i configured dynamic PAT and are all internet .
i want configure identity NAT for remote access VPN.Remote users IP pool is 10.10.10.0 to 10.10.10.10
i know to configure NAT exemption in IOS 7.2 version. But here IOS 8.3 version. configure NAT exemption for 192.168.2.0/24 to my remote pool( 10.10.10.0 to 10.10.10.10).
View 6 Replies
View Related
Apr 16, 2011
I have a ASA 5510 actve/standby and create one site to site VPN with remote peer ip address xx.xx.xx.xx, Our VPN traffic running on 6 mb internet link for video conferancing traffic.Now client give another link 2 mb internet and client told to us our data traffic runnig on 2 mb link but this data traffic running on the same remote peer IP xx.xx.xx.xx.
Secondly request also they need failover over the ISP link.
how we immplement the same on ASA 5510.
View 0 Replies
View Related
Oct 10, 2012
I have a ASA 5510 at our corporate HQ that has one site to site VPN. I need to add 6 additional site to site VPN's to this ASA for our remote branches. How can I add them without affecting the existing site to site VPN? The 6 site to site VPN's will all have the same settings however these settings are different from the existing site to site that I already have set up. How can I set it up so the 6 additional VPN's use their own crypto map and all use the same settings?
View 1 Replies
View Related
May 28, 2012
I have a ASA 5510 that has multiple site to site VPNs. I need to create an additiona site to site VPN but only allow 1 host to access and traverse the tunnel. The network is on a 192.168.5.x but the host that will need to access this tunnel needs to be on a 172.16.33.x network. I dont want any other traffic allowed to access or traverse the VPN tunnel for this host. How can I set this up?
View 33 Replies
View Related
Apr 30, 2013
I have an ASA 5510 8.2(5) in Site1 and a ASA 5505 8.2(1) Site2 they are setup with a site to site tunnel.Each site has VPN clients that connect and I would like to allow clients from both sides access to servers on the other side of the site-to-site tunnel.
I enabled same-security-traffic permit intra-interface I also added the remote networks to access-list that is doing the split tunneling. [code]
View 33 Replies
View Related
Feb 14, 2011
I have a cisco ASA 5510 at the branch here. It terminates about 8 vpn tunnels and also it supports remote access clients. I just have a quick question. Can my remote sub-net group access the other remote access site-site VPN subnet group. If yes then how should i configure it.
View 6 Replies
View Related
Sep 30, 2012
I have a dynamic VPN site to site between ASA 5510 vs C880 with segment 172.23.191.0/25 for ASA side and some host in C880 side (e.g. 128.1.100.211, 128.1.115.181, 128.1.104.212) . The VPN is up, but only have communication with a host (128.1.115.181).
In the logs appears the next message when I try communication for all aother IP in the policy map configuration: IKE Initioator unable to find policy: Intf Inside, Src: 172.23.191.87, Dst: 128.1.115.182..ONLY WHEN I PINGING FROM SOME HOST IN C880 SIDE (e.g. 128.1.100.211) the communication is successfull.
What happen with this VPN, because I need to pinging from C880 IP host to ASA segment for establish communication?
View 7 Replies
View Related
May 26, 2011
I'm trying to figure out how to get two 5510 ASA's to establish a Site-to-Site VPN.The version with two static IP's is working perfectly and stable but I haven't figured out how to get a VPN running between a static and a dynamic IP
View 12 Replies
View Related
Jun 28, 2012
I am attempting to configure Radius authentication accross a site-to-site VPN for my ASA 5510-01 for remote access.
ASA5510-1 currently has a live site to site to ASA5510-2.
ASA 5510-1 - 10.192.0.253
ASA 5510-2 - 172.16.102.1
DC - 172.16.102.10
ASA5510-01 can ping the DC and vica versa but is unable to authticate when i perform a test. ASA5510-01 can authenticate to a DC on it;s own LAN but not on the remote LAN that DC sits on.
I have double checked the 'Server Secret Key' and ports as well as various users which all work locallly. ASA5510-02 authenticates to DC with no problems.
View 3 Replies
View Related
Sep 17, 2012
I'm setting up a Site-to-Site Cisco VPN between ASAs. I'm being told by the remote site engineer to set the maximum MTU at 1362. Is it possible to set the MTU for one specific site-to-site VPN on my ASA 5510 Security Plus to MTU 1362? I see my interfeces are all set at 1500. If not, would you recommend I setup a subinterface on my inside network router and a subinterface on the ASA with an MTU of 1362 to get around this issue? Then use this subinterface for traffic from my inside network to transverse through prior to hitting the VPN.
View 1 Replies
View Related
Oct 3, 2012
Site A has an ASA 5510 and a single internet connection.Site B has two internet connections (primary and backup). If Site B also has an ASA, I can configure Site A's ASA to deal with a failover at Site B (set peer 1.1.1.1 2.2.2.2). Does this work if Site B has an IOS router instead of an ASA? In other words will "set peer 1.1.1.1 2.2.2.2" on the ASA work when it's talking to IOS on the other end?
View 15 Replies
View Related
Apr 18, 2013
I am not very experienced with Cisco networking.
Here is the situation.
Site A - headquarters 192.168.1.x
Site B - remote office 192.168.20.x
Site C - remote office 192.168.30.x
Site A - ASA 5510
Site B - ASA 5505
Site C - ASA 5505
Site-to-site VPN is established and works between A and B, A and C. Users would like to establish a tunnel between B and C to work on a common project and the data is on Site B.
I tried configuring the S2S VPN with pre-shared keys on both firewalls at sites B and C but in the end it is not established (I cannot ping either side). I used the Wizard interface multiple times and one time the CLI. I generally followed the settings chosen between the headquarter and the individual remote sites and tried to replicate them. Obviously I have made a mistake somewhere.
Could there be any limitation on the ASA 5505 in terms of licensing and the number of S2S tunnels?
View 7 Replies
View Related
Jan 29, 2011
I have a site to site tunnel (bidirectional) configured between two ASA 5510's (head office and remote office) running 8.2.2. I'm trying to upgrade one end (head office) of the tunnel to 8.3.2 but when I do that, traffic from the remote office to the head office isn't transported. Traffic from the head office to the remote office is still fine (remote desktop sessions, etc).
A quick comparison of the 8.2.2 config and the 8.3.2 config on the head office ASA look identical in terms of the crypto/site-to-site commands.Is there any Cisco guide created yet for creating site/site tunnels under 8.3.2? I'm able to upgrade both ASA at the same time if that's determined to be a prerequisite.
View 2 Replies
View Related
Dec 12, 2011
We have a Cisco ASA 5510 at our main office that makes connection with a 5505 at our other office using site to site VPN. (works)
Now for the question,
we want to access our other office from the main office but we wont want them to have access to our servers etc. so basically we want to control them but they shouldn't have the rights to control us.
Is this possible with a site to site VPN? and how to do it.
View 7 Replies
View Related
Jul 12, 2012
Our HQ office has an ASA 5510 with full access to internal and external IP's. We have a small group of remote users that are working from a shared office suite and they only have Internet access by way of internal default gateway. Using a VPN client is not desirable due to many other devices requiring access to HQ. Is there a way to create a site-to-site VPN from this remote office space back to HQ (ASA 5510) if they have no access to the public IP address on their end?
View 2 Replies
View Related
Nov 29, 2011
I was traying to make a site to site VPN between a cisco 1800 router and cisco asa 5510. But it was impossible to get it. [code]
View 1 Replies
View Related
Feb 20, 2013
I have a situation where I need to have remote users vpn into my ASA 5510 and then turn around and hit a site to site tunnel. Now when I am in our office I can hit the site to site vpn fine. When I am at home and vpn to the asa I can not get to the site to site resources. Do you see where my config is incorrect? result of the command: "show run"
ASA Version 9.1(1)
!
hostname xxxxx
domain-name xxxx
enable password xxxxx
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
[ code]....
View 3 Replies
View Related
Oct 3, 2012
I would like to know if there is any command that i can use to terminate a site-to-site connection and restart it whenever i want to.I don't want to use the shut down command since i use the specific interface as an exit point to the internet.
View 4 Replies
View Related
