Cisco Security :: 5510 Allocate A Bandwidth Of 512kbps For Each Connect
Jul 29, 2011
Recently i had a requirement for implementing a Qos on one of my Mpls link which is of 2Mbps, the requirement was to allocate a bandwidth of 512kbps for each connect that comes in and 512 kbps for out going, and it is in ASA 5510 firewall.
So i have done the configuration successfully, now the issue is, the bandwidth is limited to 512kbps only for all the connection,how many may be the connections, it working below 512kbps,
But my requriemt was for the first connection, it should allocate 512kbps , and for the second another 512kbps so on.its not happening, the bandwith got struckup at 512kbps , all the connection are sharing this bandwidth only.
View 1 Replies
ADVERTISEMENT
Nov 19, 2012
would like to know how a bandwidth gets distributed in switches.for example consider a scenariowhere i have a coreswitch A and coreswitch B connected between each other througha a 1Giga Fiber, now each of my core switche are connected to two edge switches through fiber links. all edge switches have giga ports. now if i connect a pc with giga link in th edge switch of coreswitch A and tansfer a file to a PC connnected to the edge switch in network B.. how much bandwidth would i get?how does the switch allocate bandwidth?
View 8 Replies
View Related
Jun 28, 2012
I have a WAG310G router which I have connected wirelessly to my PS3. When no one else is using the internet my connection is fine. However, when someone else does come on the internet my PS3 lags so bad that I can barely play it. I was wondering is there a way to allocate the bandwidth so that my PS3 gets more of it?
View 2 Replies
View Related
Nov 3, 2012
How to allocate bandwidth for a certain host or service in Cisco ASA 5510 Firewall using ASDM? For instance, I would like to dedicate 2MB for H323 service (Video Conference Call).
View 1 Replies
View Related
Sep 13, 2012
I have some clarifications regarding ASA firewall, it can be support bandwidth management and content security at the same time. we are looking for below features in ASA5510.
IP/Policy based bandwidth management.Controll the bandwidth and allocate the bandwidth to specified users or servers.Content Security. If not, which device I need to set for Internet Bandwidth Management and content security.
View 3 Replies
View Related
Jan 21, 2012
I'd like to use an SG200 swicth to allocate bandwidth on a 100 Mbps fiber Internet uplink.I will have 5 routers (each supporting a separate network) connected to the SG200, and I'd like to give each network 20 Mbps. QOS configuration, best CIR and CBS settings for this.
View 1 Replies
View Related
Mar 12, 2013
I configured Cisco ASA5510 firewall, but i am facing the problem with ssh login, i gave ssh for inside and outside access, but i am getting "server ... error" i enabled LOCAL for the authentication for ssh and HTTP. and i am able to acees the device through HTTP using ASDM, but not able to access from outside.
ASA Version 8.2(1)
!
hostname ASA5510
[Code].....
View 3 Replies
View Related
Aug 8, 2006
ASA 5510 security plus edition will it support active/active failover. and does it support context with securiyt plsu edition. and how many default context do we get with asa 5510 security plus edition.
View 3 Replies
View Related
Mar 29, 2011
We have an ISP connection that is connected via an ethernet interface on a 5510 ASA. We are allotted 10Mbps. I have currently have the interface set to 10Mbps Full. However we want to upgrade the connection to 25Mbps. I know I can set the port speed to 100Mbps and then set a shape/police statement and shape down to 25Mbps.
Management wants to be able to call the ISP and arbitrarily adjust that speed up temporarily at any time without any user/admin intervention on our side. I can simply leave the port at 100Mbps i.e. no shape statement on my side however I will run into problems with large amounts drops, overruns, retransmissions, etc due to the ISP shaping the connection speed during normal operations. However they then could then adjust the speed at any time without needing me.
I do not know the best way to make this work. Is there some sort of dynamic/smart shaper in the ASA or another cisco device?
View 2 Replies
View Related
Nov 8, 2012
I have a cisco ASA firewall 5510.Just i have configurd for 1st port as nameif ouside witch public ip, 2nd port as a nameif inside with local ip, and done the nating, dhcp and dns. now i am able to get internet from inside port, which is getting dhcp.up to that it is ok.
And I want to restrict bandwidh 1Mbps for local port (2nd port) how to config 1Mbps banwidth allocation for port no 2, I mean nameif inside should have 1Mbps limet.
View 1 Replies
View Related
Jul 27, 2011
We have a Service Policy rule setup on our 5510 for SMTP traffic.
Problem is, this week someone sent a larger email 20+mb to dozens of recipeints and the outside interface was hitting 10mb, which is not what I would have expected with this rule in place, so I'm questioning the configuration. We know it was email because I disabled the server that receices our outbound mail to apply a signature and the traffic dropped immediately.
View 2 Replies
View Related
Oct 31, 2011
I have a 20/20 MB circuit and an ASA 5510 and I am able to setup policing were the interace gets 512k down and 128k up so when I conduct a speed test with one user I get 512k and 128k and when I conduct a speed test with two users each gets 256k and 64k. [code] What I want to happen is that each user gets 512k and 128k until a saturation point is hit and then I want the ASA to slow all users down equally.
View 1 Replies
View Related
May 5, 2011
I'm working in my lab trying to do proof of concept for traffic policing on the ASA 5510 running 8.0(4). I have two laptops running Ubuntu one on the outside and one on the inside. Both laptops have 100Mbps interfaces. My tests consists of downloading a file from one laptop using HTTP. Without any QoS I can see speeds close to 100Mbps which I would expect. On a side note, try using XP and you won't come close to those speeds. Anyhow, I implement policing using the config below and expect to see the max rate on the laptops during the transfer max out close to the CIR. However, I see speeds much higher on the laptops.
When I set the CIR to 10000 bps with bc at 1500 bytes I get speeds that range from 300Kbps to 700Kbps. I would expect to see speeds max out at the CIR which would be 10Kbps.I'm having a hard time understanding why my numbers don't match.
View 6 Replies
View Related
Dec 22, 2008
I matched the traffic statistics on one of my Cisco ASA site-site tunnels with the OID:1.3.6.1.4.1.9.9.171.1.4.3.1.1.25.4142 (cipSecTunHistInOctets). I was real proud of myself for a few days until I checked the history and found the OID wasnt working.After some troubleshooting I found that the last four digits (4142 in this case) change whenever the tunnel drops and re-establishes itself. Any way to collect tunnel utilization history on an ASA with SNMP? Is there a different OID I can use thats based on the endpoint IP?
View 2 Replies
View Related
May 1, 2012
I am using ASA 5510 Firewall and i have established VPN tunnels too , now i want to Monitor the bandwidth utilization , i have installed PRTG Monitor application and want to add the firewall , how to enable the SNMP in ASA .
View 1 Replies
View Related
Jul 29, 2012
In ASA 5510. How I can limit the users in (VLAN 20) to use the internet with a limited Bandwidth/speed with 3 mbps upload and 5 mbps download?
In case the outside interface (Native vlan) which is connected to the ISP and have a bandwidth/speed of 30 mbps upload and 50 mbps download.
View 4 Replies
View Related
Apr 23, 2013
Is there a way to allocate CPU or memory resources to specific processes - similar to a QoS-style configuration where you can prioritize the processes being handled by the CPU? We have a 2811 router whose CPU periodically spikes to 100% utilization. At these times, all of our EIGRP neighbor adjacencies bounce - either a peer goodbye is received or the hold time expires.
Our thinking is that we could possibly tell the router to prioritize the EIGRP process with the CPU so that routing is maintained, even though we realize other processes (like qos or ISAKMP for our tunnels) may suffer.
View 2 Replies
View Related
May 9, 2011
I got a 40gb monthly broadband plan at home and there are 4 of us using the broadband..since i work long hours i hardly use internet but other flatmates sometime finishes the broadband 10days before the new cycle starts..so i was wondering if there is a way i can put a limit that every one get to use 10gb.
View 3 Replies
View Related
Jun 7, 2011
We saw this syslog on ASA5585 with version 8.4(1). I have two HA firewall pairs (contains 4 ASA5585, active/standby), and I saw this message on the standby ones.
Jun 7 07:36:26 10.99.96.32 last message repeated 4 times
Jun 7 07:36:26 10.99.96.32 :Jun 07 07:36:26 HKST: %ASA-ha-3-210005: LU allocate connection failed
[Code]....
View 4 Replies
View Related
Feb 17, 2013
Customer is running ASA 5550 with software 8.2.5 version.
They continously get the below messages
%ASA-3-210005: LU allocate connection failed
%ASA-3-210007: LU allocate xlate failed
I have already searched in the forums and also BUG toolkit, These issue has either been resolved in prior relases or in 8.4 .x train. I didnt find any bug which says that it has been found in 8.2.5 release.
I have also run "show conn count" and "show xlate count" I see these is difference in count output.
From Standby
COGINBLRMBPB1INTF1# show conn count
6097 in use, 17220 most used
COGINBLRMBPB1INTF1# sh xlate count
[Code].....
View 2 Replies
View Related
Nov 10, 2011
My WRVS4400N, V2.0.2.1CPU:STAR 9202.Doesn't allocate IP address on DHCP for anything but the Open SSID. All others, WEP, WPA, WPA2, nothing.I tried different clients, Intel Centrino wifi, Cisco, AG-CB21 same results.The config is std, I tried one VLAN for ALL SSID, I tried different VLANS, same.
View 0 Replies
View Related
Oct 10, 2011
we have two ASA 5520, on the failover unit is showing LU allocate xlate failed. We read on [URL] that it could be a memory problem , but have cheked it and we have 85% of memory free on both nodes. We also can see all xlate on failover unit.
We have forced failover this evenig and we can´t stablish outbound connexions by outside interface, we think xlates or nat cant work properly.
View 5 Replies
View Related
Sep 13, 2011
I got an asa5510. After problems with ipsec connections the log said :
LU allocate xlate failed this error repeats every minute. At the cisco site i found the following :
explantion : stateful failover failed to allocate a translation (xlate) slot record recommended Action : check the available memory by using the show memory command to make sure that the security appliance had free memory in the system. If no memory is available, add more memory
But when i do there is free memory. (about 54%)
What can i do to fix this ?
View 2 Replies
View Related
Mar 23, 2012
I want to ask for the possibility of configuration below? 2x Cisco ASA 5510 running Multi-Context mode and Active/Active Failover1 Cisco ASA 5510 (ASA 1) has AIP-SSM1 Cisco ASA 5510 (ASA 2) has CSC-SSMThere are 2 contexts, context A and context BASA 1 is the primary firewall for context A, and secondary firewall for context BASA 2 is the primary firewall for context B, and secondary firewall for context A
Can AIP-SSM on ASA 1 inspects traffic of context B which primarily runs on ASA 2?Can CSC-SSM on ASA 2 inspects traffic of context A which primarily runs on ASA 1?
View 2 Replies
View Related
Mar 24, 2010
We just had an issue with our failover unit reloading. In perusing the logs there were a number of %ASA-3-210007:
LU allocate x late failed, errors prior to the reload. These units had just had their OS upgraded to fix a DOS issue a few weeks ago. I have not seen the error since it reloaded. However, I was asked to report the issue just in case it is a bug in the new version of the OS.Two units in failover.
Cisco Adaptive Security Appliance Software Version 8.0(5)9 Device Manager Version 6.0(2). Compiled on Mon 01-Feb-10 10:36 by buildersSystem image file is
"disk0:/asa805-9-k8.bin"Config file at boot was "startup-config"
CP-ASA up 17 days 21 hoursfailover cluster up 17 days 22 hours
[code]....
View 1 Replies
View Related
Aug 18, 2011
I want to upgrade my ASA 5510 from version 7.0(6) to 8.2(5). Reading the release notes for 8.2(5) it says the DRAM requirement is 256MB unless you have high CPU usage. Also it says I need to upgrade through the major releases, from 7.0(x) to 7.1(x) and 7.1(x) to 7.2(x) and then from 7.2(x) to 8.2(x). The questions are:
- My ASA has 256MB of RAM and 68% of free memory, would you think it will run the 8.2(5) version with no problem?
- When making the upgrades to the major releases, is there any consideration regarding the configuration file? Or the versions to use for the 7.1 and 7.2 versions?
- Would you recommend making all the upgrades in one maintenance window? How much time could it take?
View 2 Replies
View Related
Aug 21, 2012
We’ve ordered ASA 5510 with security plus license as below description:
ASA5510-K8
ASA 5510 Appliance with SW, 5FE, DES
L-ASA5510-SEC-PL=
ASA 5510 Security Plus License w/ HA, GE, more VLANs + conns
The license details on the appliance shows as the below,
Fail over : Enabled
Encryption-DES : Enabled
Encryption-3DES-AES : Disabled
Security Contexts : Default
GTP/GPRS : Disabled
Any Connect Premium Peers : Default
Other VPN Peers : Default
Advanced Endpoint Assessment : Disabled
Any Connect for Mobile : Disabled
Any Connect for Cisco VPN Phone : Disabled
Shared License : Disabled
UC Phone Proxy Sessions : Default
Total UC Proxy Sessions : Default
Any Connect Essentials : Disabled
Bot net Traffic Filter : Disabled
Inter company Media Engine : Disabled
I’ve noticed that the 3DES is disabled, do I need to order another license to use 3DES or not ?Also, I need 2 ~ 5 branches to connect simultaneously and have VPN access on their laptops to the main branch via vpn software, which VPN software I should use and is our license enough or I should order another license.
View 3 Replies
View Related
Sep 26, 2012
i have upgraded a PIX 525 lately to a 5510 ASA, but i have faced a problem after this.One of the DMZ's are connected to a switch that is not connected to my VTP domain on a DMZ port.
with access-list to permit from host to host with all ports opened.my problem is that the outside client is able to initiate a windows VPN to a server that i have in the DMZ, BUT it disconnects after almost 10minutes. What might be the reason of the disconnection.Note, a cisco remote access VPN is also configured on the FW, and it doesnt disconnect.
View 1 Replies
View Related
Aug 2, 2011
trying to TS a VPN device that is behind an ASA basic set up is IOS VPN<firewall/nat<internet>ASA/nat>IOS VPN
I do not have a lot of insight into the other side of the connection, although the tech on the other side claims all is good. so to the point.
Is the asa capable of allowing this tunnel to work? The configs and debug follow.
1.1.1.1 = my public ip
2.2.2.2 = peer public ip
The asa -
[Code]......
View 2 Replies
View Related
Mar 25, 2011
I was under the impression that those global addresses that we used with NAT were from the outside IP addresses range?Lets say my outside IP address is idk 192.112.40.11 /30 and I only had two usable IPs (since you can't use network and broadcast IPs) so how would I set up NAT for a couple of Inside addresses with a shorting of addresses like this? Idk if that makes sense what I'm trying to say
View 3 Replies
View Related
Sep 22, 2008
I'm trying to monitor Tunnels activity. We want to gather statistics like bandwidth utilization per Tunnel and in the case of Remote Access also the user name associated with a tunnel. All this via SNMP
I've browse through the Cisco-IPSec-Flow MIB and found the TunnelTable, this seems to provide everything I need in Regards to Tunnels, I just need a tip in how to calculate or obtain the bytes Tx and Rx. I can obtain packets and Octets amounts but not actual bytes. Is there another OID I should be inquiring?
In regard to Remote Access I found the CRASSessionTable From here I can obtain the Group associated with the tunnel and I should be able to obtain the User name through the 1.3.6.1.4.1.9.9.392.1.3.21.1.1 OID, but I'm getting an UnSupported response when querying this particular OID.
What OID can provide the User name?
I know that Cisco Performance Monitor can in fact obtain all that info from the ASA so there must be an appropriate OID I can query to obtain this particular info.
View 3 Replies
View Related
Sep 28, 2011
I have a ASA 5510 that uses Radius for Authentication. What I am trying to do is assign each user that logs into VPN to have a specfic static IP based on userid. I have about 30 to 50 users. I don't want to complicate this by having them select a different profile when logging into the ASA. What is a clean and simply way to assign user static ip and not use local database for login?
View 1 Replies
View Related
Feb 20, 2011
I got a task to replace our current cisco 2800 series router which is used for easy vpn remote access with cisco asa 5510.I have a got a lot of users, i wish that user shall see no difference except of ip address they are going to use for remote login.
View 1 Replies
View Related
