Cisco Switches :: SG300-28P Noise Level Too High
Mar 13, 2012In official information for SG300-28p noise level is 40.6 dB, but in fact its too noisy. Is it possible to change speed of fans? I use only 8 PoE ports.
View 1 Replies
ADVERTISEMENT
High Noise On Cat.6 SFTP Cable Running Close To AC Lines
Nov 29, 2012I have an application, a solar power plant, where communication cables (Cat.6 UTP) are run close to power cables. We've had a lot of failures in the past due to multiple reasons, electrical noise, surge, etc so we decided to change to Cat.6 SFTP. The problem is that now , even with proper termination of the shielding at either one or both ends, the noise is so bad that packet loss is above 90%.
View 8 Replies View RelatedNetworking :: High Pitch Noise Coming From Motherboard When Ethernet Cable Plugged 7970
May 9, 2013This has been driving me absolutely crazy but I am glad to have found the source of it. Over the past 4-5 weeks ever since i built my new computer, my computer has always had this wierd high pitch noise. I dont know if its coil whine or not, but the sound signature is def not the same as the coil whine that comes from my 7970 card. It sounds more digital.
What could be the cause of this? And what would the remedy be? My ethernet cable is approx 60 ft so it will be a pain in the ass to replace. Or buy another NIC?
edit: forgot to mention....the noise is constant. Not intermittent with usage. No amount of load or idle on the network changes the noise.
Cisco Switches :: SG300-28 GUI Different Than Online SG300-48 Simulator
Aug 29, 2011These are our first switches and seems like GUI is lot different than the online. Out intervlan routing is o not working. I am absolutely sure that I setup the switch in L3 mode since it allows me to create mutiple interfaces. I am hoping that this GUI issue is related to interVLAN routing.
Below is the blog I started for InterVlan issue [URL]
This is the link for online simulator and what I see in its IP tab. I know this switch is not SG300. [URL]
This is what I see on our switch.
Our switch version
switchd64684#show version
SW version 1.1.0.73 ( date 19-Jun-2011 time 18:10:49 )
Boot version 1.0.0.4 ( date 08-Apr-2010 time 16:37:57 )
HW version V01
Cisco Switches :: SG300-28P And SG300-52 Web Managing - Fans
May 26, 20111) I have a Cisco SG300-28P. I plan to add a SG300-52. Would it be possible to manage the new switch through the SG300-28P web browser ?
2) There are 2 fans in the POE model SG300-28P. How many fans are they in the non POE switch SG300-52 ?
Cisco Switches :: SG300-28 Uplink To Another SG300-28?
Feb 8, 2012Can I connect a single Cat5e cable between two SG300-28 and link them? If so what must I configure?
View 1 Replies View RelatedCisco Switches :: Difference Between SG300-28P And SG300-52
Jul 25, 2012I have SG300-28P that I am using as layer-3 switch. Recently I ran in to SG300-52 switch and even though loading same firmware doesn't give me option to do layer-3 switching. For SG-300 I see options in GUI to create vlan interfaces under IP information section, while SG300-52 has IP information option only under the management section.let me know if these are 2 different hardware types and L3 is not possible on SG300-52. If its possible to enable L3 switching on SG300-52?
View 2 Replies View RelatedCisco Switching/Routing :: SG300-10 High CPU - Lockup And Restart
Dec 12, 2012I have an sg300-10 unit. I have recently swapped it into my LAN network to replace an aging switch that was exhibiting problems.
The SG300 is reporting near constant 100% cpu load with 11pps input. there are only 3-4 active ports on the switch at a given time. One of those ports does lead to my router and another switch with another half dozen devices.
By itself this doesn't concern me overly much, but I have found that the SG300 is occasionally freezing up for about 20 minutes then restarting. Syslog and SNMP traps don't appear to provide any hints as to what is going on.
I have tied my switch into my monitoring system (packettrap MSP, so if there is something I should be watching that I am not, that would be good to know). I am still troubleshooting getting all the monitoring functions working as well.
So, I have some questions there as well, which OID should I be monitoring for CPU utilization?
Cisco Switches :: Replacing 3COM 4500 Switches With SG300-52?
Nov 21, 2011I'm replacing 2 3COM 4500 Swithes with the SG300-52 Cisco switch. We have 3 VLANs, 10, 20, 100. The switch is set for Layer 3 and I have setup DHCP relay. what settings i should set on the Cisco for the following setups:
3COM Setup
#
interface GigabitEthernet1/0/1
[Code].....
Cisco Switches :: SG300 Switches Have Poor Performance In Layer 3?
Jan 1, 2013We have several of the SG300 Serices switches. We use them to route VLAN traffic to Remote Offices, Internet Connections, and WiFi Access Points.In one remote office we have a SG300-10 setup to route the HQ Network and the remote Office Subnet. The SG300 is Connected to HQ via Fiber and has multiple Tagged VLANs on it. If I do speed tests over the Fiber Link on the Incoming Tagged Netwotk I get Decent performance, 80Mbs. If I switch to a networtk that is not priginating from HQ, and have the SG300-10 route packet, I get dismal performance. 15-20Mbs.
I Fireded up a New SG300-28P FW v1.2.7.76. Added a the HQ VLAN 101 and new VLAN 1025 . Mapped some Tagged and untagged ports for each. Switch was connected to HQ Network as untagged VLAN 101. I put a laptop on an Untagged VLAN 101 port. Ran some tests, cam back with 750-850Mbs. Great. Put the same laptop on a Tagged 101 Port, Configured the NIC for Tagged VLAN 101, Same test, same Speeds, 750-850Mbs.I then Configured laptop for Tagged VLAN 1025. Connected to tagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!
I then Configured laptop for Untagged VLAN 1025. Connected to unagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!It was only the Laptop and the Connection to the HQ net on the SG300-28P. Why is the performance of this unit soooooo poor when it needs to route?Other Switches have FW v1.0.0.27 or FW v1.1.2.0. They have Similar speed issues. All Configured for Layer 3.
Cisco Switches :: SG300 Switches Can Be Used With Microsoft NLB In Multicast Mode
Dec 18, 2011does the SG300 switches can be used with Microsoft NLB in Multicast mode?I know on traditional Catalyst switches you can statically "map" IP's to mac's and then to multiple ports but this doesn't seem to work correctly on the SG switches - it gives an error about the mac not being not Unicast?
View 2 Replies View RelatedCisco Switches :: VLAN Management Via SNMP On SG300-10 Switches
Aug 7, 2011Any snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
View 8 Replies View RelatedCisco Switches :: Multiple VLANS And SG300-28P Switches Setup?
Aug 20, 2012I'm going to have several SG300-28P switches to setup. I'll need to create multiple vlans for data, voice, and wireless traffic. I have the following questions in setting up this configuration:
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice
1) For managing the switches via IP, will LAN1 be the default management network? Should I create a seperate VLAN for managing the switches?
2) For uplinking the switches together, I plan to trunk a port to connect the switches together. What's the configuration on the trunk port to forward all vlans from one switch to another?
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC. The phone supports tagging for the PC and the VoIP traffic. For example on port 10, would VLAN 100 and 300 be set to tagged?
Cisco Switches :: SG300-52 Multiple Lags Between Switches?
Jan 19, 2012I'm having alot of trouble trying to connect more that one LAG between two SG300-52 switches.Basically i have configured both switches with the same vlans. For 2 of the vlans i would like to connect them together between the two switches using LAG. Switch1 has Vlan 5 (ports 1-12) & Vlan 10 (Ports 25-36) with LAG configured on ports 1-2 and ports 25-26. I have setup the second switch identical to the first. But when i connect the LAG's there is no connectivty. If i disconnect one LAG the other starts working.Can you only have i interconnect LAG between switches?
View 1 Replies View RelatedCisco Switches :: How To Configure Two Links Between Switches SG300
Apr 22, 2012I have two SG300 serie switches and two Gigabit connection between them. How do I configured these two links to work toghether like a one 2 Gigabit channel?
View 2 Replies View RelatedCisco Switches :: VTP And STP On SG300-28 Switch
May 9, 2011I have a question, does the SG300-28 support VTP and STP?. I want to add it to my network's VTP domain so I don't have to manage vlans manually on the SG300-28 and also be able to configure STP to keep my network loop free.
View 2 Replies View RelatedCisco Switches :: Set Up LAG Between SG300-20 And SRW224G4P
Jul 19, 2012On my SG300 I set up LAG for the last two ports.
I then plugged them into my SRW224G4P, once I do that I get dropped packets.
I was thinking maybe doing firmware upgrades to both switches?
Cisco Switches :: How To Assign SG300-10 To VTP
Jan 29, 2012I need to know how to configure each port in switch SG300-10 to vlans, i need to configure one port "trunk" with catalyst switch and assign 4 ports to different vlans. any solution?
View 2 Replies View RelatedCisco Switches :: Does SG300-10 Support RIP
Jun 20, 2012In the CLI documentation for the SG 300 Series, it shows sh ip route rip as a command. I have installed the latest firmware and that command is no longer available. Does the SG300 series support RIP?
View 6 Replies View RelatedCisco Switches :: SG300-10MP Keeps Going Down?
Jan 27, 2013We purchased a SG300-52 last week to replace a 5yr old Dlink which has worked perfectly. 1 day after the SG300 went it it started crashing with this fatal error problem so I reverted the firmware back from 1.2.7.76 (latest) to 1.1.2.0 but I still get the problems. It crashes when I have it on my lan with users connected or if I just have the switch on my desk with just my laptop connected, so it cant be a load issue or a network topology issue. I already have a Cisco SGE2010 on my network without problems.
View 7 Replies View RelatedCisco Switches :: ACL Binding On SG300 28P
Mar 15, 2011I have a question about ACL and binding. I have a SG300 28P and a couple of other linksys switches and Access points that are connected to it via trunks. The cisco SG300 28P is running in layer3 mode and i have created a couple of vlans and one of them is a guest vlan. Now to my question, i create an ACL and an ACE that vill funktion so that guest vlan only can connect to the internet and not the rest of the internal network. And then i must bound the ACL to an interface port or lag, what i can see it is not possible to bind it to an vlan? so if i have a port on some of the other switches that is member of the guest vlan, vill the ACL on the SG 300 stop guest vlan trafic to the internal network that is comming from some of the other switches?
View 1 Replies View RelatedCisco Switches :: SG300 - Set Up VLan Only For Wi-Fi APs?
Mar 25, 2012I want to set up a vlan only for the wifi APs and wifi clients on my network. They can't access to any server, only internet acces. I already implement this configuration and its working, but now I want to allowed a couple of laptops to connect to servers in other vlan. what should I do? Should I do it using Mac address of laptops or IP?
View 9 Replies View RelatedCisco Switches :: SG300-10P SYN Protection
Mar 1, 2013Yesterday I upgraded my SG300-10P to firmware 1.2.7.76. I was curious about the new SYN Protection feature, but it seems to do nothing on my installation.
The switch is running in Layer 2 mode. I have ACLs in place and DoS prevention is not enabled. I also tried clearing ACLs and enabling DoS prevention. As I understood the Admin Guide enabling DoS in the Security Suite Settings is not necessary for using the SYN Protection.
In my firewall I see about 300 pps with SYN flags only arriving. What "they" do is sending me SYN packest to port 80 from forged IPs, so that my system should send SYN-ACKs to the victim system. In this case it is the Arab Bank. They are down at the moment...I think that is called a spoofed SYN flood attack.
So I thougt the SYN Protection feature should exactly solve that problem but it does not and does not show any "Last Attack" entries.
If I put a SYN filter in place it works, even if I put SYN Rate Protection in place. But that is just a dirty workaround. My firewall blocks those SYN packets with a SNORT rule.
CIsco Switches :: SG300 Or SG500 That Has All Ports As SFP?
Feb 14, 2013Is there an SG300 or SG500 that has all ports as SFP ports?
View 1 Replies View RelatedCisco Switches :: VLAN Config On Sg300?
Jan 26, 2012I am using a couple cisco sg300 28P switches along with a sonciwall firewall/router. The sonicwall was already in place and working so they didnt want to replace it. I understand how to configure the vlan on the sonicwall, but could use some info on the cisco. I would basically like to create 3 vlans, 1 default for management, 2 for pc's on lan, and 3 for the cisco spa504g phones/'voip. Would i just go into the vlan managment, configure the 2 new vlans and give them two id's? These offices have one network drop, so the phones and pc's will be sharing the switch ports, however the phones have a setting to configure the vlan id so they know which one theyre on. Is there anything i need to do after that? I want to make sure that vlan 3 has the highest priority becuase its voice, is there some qos configurations i need to make on that switch as well? Also, the port that links the two cisco swtiches together, does that need to be set as "trunk" port? I understand what vlans are, but its just the first time ive run into these cisco models. .
View 0 Replies View RelatedCisco Switches :: SG300-10 IPv4 Routes Bug?
May 10, 2013I bought the SG300-10 Switch a few days ago and updated it to firmware 1.3.0.59, but i think there's a bug in this firmware. If I go to "IP Configuration" IPv4 Routes" in L3 Mode nothing is displayed. In the log file i see that:
21474773112013-Mar-16 09:51:34Error%HTTP_HTTPS-E-DIAGNOSTICS: ERROR - in <RL_vtLeadTableGet> tag, can not find the table rlInetRoutingDistanceTable in the MIB. 21474775182013-Mar-14 22:39:22Error%HTTP_HTTPS-E-DIAGNOSTICS: ERROR - in <RL_vtLeadTableGet> tag, can not find the table rlInetRoutingDistanceTable in the MIB., aggregated (1)
Reset of the Switch doesn't work.
Cisco Switches :: SG300-10MP Keeps Crashing?
Sep 4, 2012We are in an organization of 80 users with 5 Sx300 series switches with the latest firmware (1.2.7.76). The network is mostly flat with all switches feeding into a Cisco ASA5505 acing as the primary gateway for Internet Access. Only our two 48 port POE switches have an additional vlan configured for the VoIP phones. We have one SG300-10MP that is powering 5 Cisco Aironet 1024N's that keeps crashing. A couple weeks ago it went down twice in one day. I updated the firmware and it did not have any hiccups unitl today. This issue has been consistent since we installed the switch in April. Originally the issue seemed to be caused by too much bonjour traffic causing a buffer overflow (we have over 100 Apple products). Since I updated the switch I have not seen any bonjour buffer overflow errors. Instead I get the following error when it crashes:
2147424534 2012-Sep-05 15:12:28 Emergency %SYSLOG-F-OSFATAL: FATAL ERROR: tExcTask: ABORT DATA exception ***** FATAL ERROR ***** SW Version : 1.2.7.76 Version Date: 19-Jul-2012 Version Time: 17:54:43 Instruction 0x18 Exception vector 0x10 Program state register 0x80000092 %SNMP-I-CDBITEMSNUM: Number of startup configur ation items loaded: 133 %LINK-W-Down: gi1 %LINK-W-Down: gi2 %LINK-W-Down: gi3 %LINK-W-Down: gi4 %LINK-W-Down: gi5 %LINK-W-Down: gi6 %LINK-W-Down: gi7 %LINK-W-Down: gi8 %LINK-W-Down: gi9 %LINK-W-Down: gi10 %LINK-I-Up: gi9 %LINK-I-Up: Vlan 1 %LINK-I-Up: gi1 %STP-W-PORTSTATUS: gi9: STP status Fo
The CPU and PoE supply are far from being overloaded.
Cisco Switches :: SG300 And Multiple WAN Connections?
Apr 8, 2013Currently I have my SG300 connected to a Wireless Router which is, in turn, connected to a Cable Modem.
I'm considering adding a second cable modem. Can the SG300 handle that?
Cisco Switches :: LAG Configuration On SG300 52 Switch?
Sep 10, 2011I am having an issue with LAG configuration on a Cisco SG300 52 switch. I have connected four Ge ports on the switch to the four NICs of a Dell R710 Server on which I installed Windows Server 2008 R2. Without LAG configured, these ports would forward traffic to and from the Dell server fine.However, if I configure LAG on the ports with LACP enabled, then they would not forward any network traffic. Debugging shows that the ports are up but their forwarding status show N/A. Am I missing any configuration? Can I configure LAG on edgeports?
View 2 Replies View RelatedCisco Switches :: SG300-10 VLAN Configuration
Apr 22, 2012Before I launch into this can I say that I am very much a novice with regards to Managed Switches and their configuration. I have the following equipment which I have connected to the switch: [code] All of the above are on subnet 255.255.255.0.All of the above communicate with each other during normal operation.Our client is connecting to the switch but his requirement is for his system to "see" the PLC Comms Card as follows:IP: 10.0.3.61 on Subnet 255.255.252.0 .
Using the Internet Explorer interface connection I have created an additional VLAN (ID 2) on Port 10 with the intention of using this as the connection to the client ( I assume there will be further settings required to route the PLC connection to this port) but every time I try to assign the IP and Subnet values and click "APPLY" the changes are not made and the connection appears to hang leading me to reboot the switch.I have connected to the switch via console and changed the mode to Layer 3. I also assume that it is OK for the three pieces of equipment to remain on the default VLAN. How I should setup this VLAN and ultimately achieve my goal.
Cisco Switches :: SG300 Not Reachable Beyond Subnet?
Feb 6, 2013I'm trying to configure a SG300 to be reachable beyond its own subnet. Its IP address is configured by DHCP to 192.168.2.2/255.255.255.0. It is possible to ping the switch from the same subnet but not from outside. The switch is set to layer 2 mode. All routing should be done by the gateway.
Here's what I have checked so far: The default gateway and netmask are set correctlyThe gateway can ping the switchHosts in the 192.168.2.0/24 subnet have connectivity to other networks through the gateway (i.e. gateway configured correctly)Administrative interface > IPv4 interface shows the correct ip address, netmask, and gateway (greyed out because it is assigned by DHCP)the switch can ping other hosts within the same network
Is there some kind of firewall setting that prohibits the switch to respond to ip packets from outside the subnet?
Cisco Switches :: Get Vlan Communicate On SG300-20
Mar 28, 2013I am facing an issue to setup what I initially called simple network but still unable to put it together.On SG300-20 I want to setup 4.3 of the vlan are to separate users in to different groups and to secure data confidentiality.1 is for the NAS. All users on the 3 vlans must access the NAS vlan.All user should have access to internet via SG300 through the ISP provided router. How to configure this, I have every little knowledge of switching and routing? And the routing seems to be the issue I am encountering because I am able to create the VLANs and assign static IP address to them but not able to get them talk to each other. I use each vlan ip as gateway on each port assigned. [code]
View 13 Replies View RelatedCisco Switches :: DHCP Over LAG Between SG200 And SG300
Apr 17, 2013I have an SG300-10 and an SG200-26. I also have an OpenWRT flashed router that can tag VLANs.My problem right now is that my default VLAN is 1, my router is doing DHCP in VLAN 1, and I want all my network equipment to be on VLAN 1, but my SG200, when LAGed to the SG300, will not get an IP.My SG300 is pulling an IP just fine from my router DHCP pool. When I connect the SG200 directly using either 1UP port settings or 1TP port settings, I get an IP just fine. When I LAG my connection (ports 1-3 on both) I get no DHCP information sent through the LAG to either the SG200, nor to any client devices that are set for DHCP.
View 7 Replies View Related
