Cisco Switching/Routing :: 6509 VSS Utilization On Solarwinds?
Mar 30, 2011
we are using solarwinds as monitoring toll for all network devices..the solarwinds shows proper memory & cpu utilization for catalyst 3750 switches but shows hogh cpu/memory utilization values for 6509-vss...when we log into vss via cli the util & memory values are normal but same are very high on solarwinds..i have checked the solarwinds site also and fond that there was issue for 6509 related to high cpu in relase before 9.2 and 9.2 release of solarwind has resolved this issue..is anything to be checked on 6509 or as such any known bug in this regard for 6509-vss i am using software s72033-ADVIPSERVICESK9_WAN-VZ.122-33.SXI4A on my vss.
View 9 Replies
ADVERTISEMENT
May 20, 2012
From couple of weeks we have observed the cpu utilization of cisco 6509 with SUP 720 is high. During daytime from 9:00 to 21:00 it keeps increasing & reaches 98% & after 21:00 becomes normal.
View 5 Replies
View Related
Jan 29, 2011
Cisco 6509 modular IOS getting high cpu in interrupt but the switch process switching is still less. Any sugeestion what could be the problem?
Process sbin/ios-base, type IOS, PID = 16407CPU utilization for five seconds: 12%/81%;
Sometimes cpu goes upto 100%
Version - s72033-ipservicesk9_wan-vz.122-33.SXH5
View 4 Replies
View Related
Dec 6, 2011
I've noticed that my 6509's running VSS seem to have high I/O memory utilization.
I/O memory: Sw/Mod Bytes: Total Used %Used
1/1 8126344 7886544 97%
1/2 11796240 11442472 97%
1/5 RP 12058384 10715832 89%
1/5 SP 8388608 8104304 97%
1/7 8126344 7886544 97%
[code]....
View 5 Replies
View Related
Nov 5, 2012
I have having two Cisco 6509 both working are my main Core Switches with which I have all my Layer 2 VLANs configured and then distributed thru the trunks links to all the Access Switches. I have L3- Vlans also configured on them with which one switch in primary and the other is secondary. All of sudden last night I got this message on my core switch 2 this for VLAN 1 which is my users LAN, how can I check as to what would have caused the core switch 2 HSRP to be active and then in standby
*Nov 5 23:33:29.296: %HSRP-5-STATECHANGE: Vlan1 Grp 5 state Standby -> Active
*Nov 5 23:33:29.796: %HSRP-5-STATECHANGE: Vlan1 Grp 49 state Standby -> Active
*Nov 5 23:33:29.804: %HSRP-5-STATECHANGE: Vlan1 Grp 49 state Active -> Speak
*Nov 5 23:33:29.920: %HSRP-5-STATECHANGE: Vlan1 Grp 5 state Active -> Speak
*Nov 5 23:33:40.144: %HSRP-5-STATECHANGE: Vlan1 Grp 5 state Speak -> Standby
*Nov 5 23:33:41.280: %HSRP-5-STATECHANGE: Vlan1 Grp 49 state Speak -> Standby
Also last night i got call from office saying that we are getting huge delay in pinging the default gateway of the user LAN which is the same vlan as the above and it was just for few minutes and then it was back to normal and now when I came to office and check there were no logs in both the core switches. When I checked the cpu utlization it was showing me high on both the switches how can I check as to what would have caused the CPU utilisation to go high all of suddedn?
INPMHCORS01#$ sh processes cpu his
11111 11111 11111 1111111111
8885555588888666669999922222666665555511111777773333300000
100
90
80
[code]....
View 1 Replies
View Related
Oct 14, 2012
I am trying to setup netflow with on 6509 and SolarWinds NetFlow Traffic Analyzer v3.10.0
The problem I have is that after configuring the basic settings of NetFlow on both side I can't see all the traffic I expected to capture in NetFlow.
The details of my problem.
I want to monitor the traffic on VLAN 20.
In the general configuration of the switch I have entered the following
ip flow-export source vlan 10
ip flow-export version 9
ip flow-export destination 132.5.200.123 8080
Where vlan 10 is the management vlan. Vlan10 can ping 132.5.200.123 no problem.
On VLAN20 interface I configured this
ip flow egress
ip flow ingress
ip route-cache flow
When I go to SolarWinds Netflow Traffic Analyzer I can see maybe 1 or 2 packets flows, like nothing of the data. If I do a capture of the traffic on VLAN 20 I can see there is loads of IP traffic on that VLAN but why is netflow not capturing the statistics of those flows and reporting it to NetFlow ?
command "ip flow-export source vlan 10" ?
View 4 Replies
View Related
Dec 9, 2012
We have recently upgraded oor LAN and we are using couple of Nexus5548UP switches in the core with 2960 stacks as access switches. Each access switches stack is connnected to both core switches with link being port-chanels and VPCs. All is working fine, but our SolarWinds management platform (NPM) is being flooded with "Physical Address changed" events. Here is an example of messages:
NSW_Core_2 - Ethernet1/7 Physical Address changed from 000000003811 to 73616D653811
NSW_Core_2 - Ethernet1/7 Physical Address changed from 200B82B43811 to 000000003811
For each interface I have messages like these repeating.I am not sure what those messages means or if there is actually anything wrong. Performance of the network is good, there are no errors on any interfaces and I do not see anything related in the switch loggs.
View 4 Replies
View Related
Feb 22, 2012
I recently posted this same issue the other day, using TFTPd32. Now i am pretty close to fixing it. I do have a different setup; my pc ethernet port is broken so I am using an ethernet/usb adapter. I am attempting to backup my IOS from a 3550 switch to my PC.
This is the error I am getting. Code...
View 5 Replies
View Related
Nov 21, 2011
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
View 2 Replies
View Related
Nov 21, 2011
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
View 2 Replies
View Related
May 22, 2012
We have a 6509 core with the below modules running for a long time and the utilization used to be always 10 to 13 percent checking with the supplier it was told to us that due to the firewall modue we have and its normal Now 2 days back i noticed the utilzation had jumped to 90 % and now it happened again
I see that on runnung proc cpu
16407 56.1% 56.5% 55.9% ios-base
16430 35.3% 35.2% 33.9% iprouting.iosproc
the modules present
Mod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 6 Firewall Module WS-SVC-FWM-1 SAD140901XA 3 16 16 port 1000mb GBIC ethernet
[Code].....
View 1 Replies
View Related
Sep 20, 2012
I am seeing a strange situation on my 6500 switch?By having snmp walk on '1.3.6.1.4.1.9.9.109.1.1.1.1.3' (== cpmCPUTotal5sec), I came to know that there are two processor and the cpu util for switching processor is gone to 88 % and some time creeps to 99 %.
snmpwalk -v2c -c "removes" sw6500 '1.3.6.1.4.1.9.9.109.1.1.1.1.3'
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.1 = Gauge32: 12 (--- this is for CPU of Router Processor )
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.3 = Gauge32: 99 (--- this is for CPU of Switching Processor )
but when I do sh process cpu on the console, all looks normal as it shows cpu utilization of RP. why the value is so high on the switching processor ?
View 1 Replies
View Related
Dec 15, 2011
I am facing high CPU utilzation for cisco4507R,
sup:
WS-X4516-V
ios version:
cat4500-entservices-mz.122-54.SG.bin
!
show process cpu
CPU utilization for five seconds: 97%/1%; one minute: 97%; five minutes: 97%
[code]....
View 8 Replies
View Related
Apr 16, 2013
I'd like to know what is "masks" in the output of show platform tcam utilization. What does 784 mean? What effect has the number of mask in the amount of supported unicast direct routes?
I'm having trouble comparing the capacity of theese two switches, regarding unicast directly-connected routes. I know the second switch has cpu utilization issues and ip unicast failed routes over 4096 arp entries. What would be the case for the first one?
Switch 1:
CAM Utilization for ASIC# 0 Max Used
Masks/Values Masks/values
Unicast mac addresses: 784/6272 12/26
IPv4 IGMP groups + multicast routes: 144/1152 6/26
[Code]...
View 1 Replies
View Related
Mar 28, 2013
We have a Cisco 3845 router configured as a voice gateway with multi SIP trunks. But when it reachs 200 calls traffic, the CPU increase to 60-70% and caused by CCSIP_SPI_CONTROL process.
CPU utilization for five seconds: 46%/30%; one minute: 54%; five minutes: 58%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
377 400729448 171017979 2343 6.31% 10.71% 12.44% 0 CCSIP_SPI_CONTRO
[Code].....
View 2 Replies
View Related
Feb 20, 2013
i have two cisco 3750 in stack firts, master switch have all swports busy second have only 5 how can i see cpu utilizations of the second switch, and its reasonable to move somme devices from first switch to second for deacreases of cpu and memory utilisatio ns of the master? the stack tehnologies use both cpu as one? or its only for simple management ?
View 9 Replies
View Related
Apr 4, 2012
We plan to implement a large number of ACL on our Distribution switch which is a HSRP pair of 6509C switches running on sup-bootflash:s72033-psv-mz.122-18.SXD3.bin WE need to divide the Network in three layers
unsecure layer
Proxy layer
Secure layer
We have approximately 250 vlans on the our distribution switches and plan to implement 15 ACL on different vlans Each ACL can contain upto 30 lines or less.
basic ACL example we will be applying on different vlan
vlan 200
ip access-group test123 in
My question is Can these ACL on a vlan can have a massive impact on the 6509 CPU ?
View 1 Replies
View Related
Jan 31, 2012
We are facing high CPU Utilization on Cisco 3750X-48P-L without any traffic on it. find the attached log files for 2 separate 3750's stack, we have upgraded the IOS of SW2 from "c3750e-universalk9-mz.122-55.SE3.bin" to "c3750e-universalk9-mz.122-55.SE4.bin" but still we found the same issue with CPU utilization.
View 4 Replies
View Related
Apr 24, 2013
I've been looking at reported problems with our Vdeio Conferencing kit attched to a stack of 3750's (which I think is down to QoS) but this got me looking at the logs. We get a lot of high CPU utilization warnings mainly for SNMP (315), Hulc running con (95), Virtual exec (289). I understand the last two are normal, and the SNMP one is probably Cisco Works polling as it happens every 4 hours.
However I've got an odd one: Apr 25 07:34:58: %SYS-1-CPURISINGTHRESHOLD: Threshold: Total CPU Utilization(Total/Intr): 93%/0%, Top 3 processes(Pid/Util): 296/85%, 144/0%, 154/0%
What is Pid 296? It's not listed on the switch:
293 39056 18456 2116 0.00% 0.00% 0.00% 0 SpanTree Helper
294 8 73 109 0.00% 0.00% 0.00% 0 EEM Server
295 0 2 0 0.00% 0.00% 0.00% 0 EEM Policy Direc
[Code].....
View 7 Replies
View Related
Feb 12, 2012
First of all I purchased the switches with part no. WS-C3750X-48P with the following IOS c3750e-universalk9-mz.150-1.SE1 & IOS feature license to work as ipservice.
Symptoms:
1) - When running the switches in stack mode (connecting the booth switch with full-duplex stack) I found the cpu utilization on each switch reached to 34% The Hulc LED Process reaches to 20%
3) - After about 1 hour with no connections to the switch I found the status not changed.
4) - I tried to run each switch in stand-alone mode (without stack cables connected) & monitor the status of the cpu utilization. I found it the same problem exist. Actions taken:
1) - Refereeing to the internet I found a bug ID describing the status of the mentioned symptoms (attached)
2) - I made a down grade for the IOS version to be c3750e-universalk9-mz.122-58.SE2.bin
3) - The mentioned IOS solved the Hulc LED Process (became 1 : 3 % ) & however cpu utilization became 18% with no links or traffic connected to the switches.
4) - I guess that 18 % utilization is too much for a free switch (refer to the show run file) as I did not configure any advanced commands.
View 5 Replies
View Related
Mar 19, 2013
Cpu always hitting 70% to 80 % and interrrupt traffic is 70%. Want to know the root cause for this issue.
CPU utilization for five seconds: 73%/65%; one minute: 71%; five minutes: 67%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
1 8 59 135 0.00% 0.00% 0.00% 0 Chunk Manager
2 58864 3290773 17 0.00% 0.00% 0.00% 0 Load Meter
3 1784 238001 7 0.07% 0.01% 0.00% 2 Virtual Exec
[code]....
View 1 Replies
View Related
Jan 13, 2013
I have a 2 cisco core (cisco WS-C6509-E (R7000) processor) and been working for quite sometime.they are conneted with HSRP with active standby config with a 10 g module for redundancy just today I see that the cpu utilization went to about 50% and its the same on both cores.
[Code] .......
View 5 Replies
View Related
May 3, 2012
I have some events where the CPU utilization in a cluster switches of WS-3750 is going to 100%, the process with the major utilization of CPU is the "hulc running con".
View 3 Replies
View Related
Feb 8, 2011
We have seen high CPU utilization on some Cisco switches of type 2960S. Also we got info, that applications are running with poor performance or with interruption.Following IOS is loaded: C2960s-universalk9-mz.122.55.SE
View 9 Replies
View Related
Oct 19, 2012
In Cisco 3750 facing high CPU utilization for specific period. During this period traffic response times across the switch degrades. Steps to identify interface potentially generating traffic. I have attached 'sh proc cpu history' , ' sh ip traffic', 'sh proc cpu sorted' during troubled period .
View 5 Replies
View Related
Dec 13, 2011
We have cisco 4510R+E switch with IOS-XE Software Version 03.01.01.SG RELEASE SOFTWARE (fc1).Our this switch is having two core & one core is always going to about 90% to 98% cpu utilization while other core is showing normal (about 5% to 10%),we check with-This switch is gateway of our LAN.
View 6 Replies
View Related
Dec 9, 2011
I am experiencing high cpu utilization in my 29501 switch. see the copied sh process cpu output.
CPU utilization for five seconds: 99%/95%; one minute: 89%; five minutes: 37%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
1 0 2 0 0.00% 0.00% 0.00% 0 Chunk Manager
[Code].....
View 4 Replies
View Related
May 22, 2012
I am running a 1712 12.4(25d) with NAT, VPN and FW/IDS. I have a broadband ethernet connection at 20mb. As I run some traffic through it, the processor jumps up to near 100% and throughput comes to a screeching halt. IP CEF is turned on and makes no difference when it is turned off or on.
View 3 Replies
View Related
Feb 16, 2012
I am a new network engineer on a retail company and I am having a problem on the High utilization of my 3-stack switch 2960 only during Peak Hours of the Store Sales.
Note: on Peak hours, it is peaking at 90-95 %
here is the utilization after Peak hours:
4444333334444433333333333333333333333333333333333333333333
[Code]......
View 4 Replies
View Related
Oct 29, 2012
After a power outage our standby VSS switch has not recovered. The switch keeps cycling through its initialization and then powers off all modules.
The Dead peer detection is working and VSL links are up.
View 6 Replies
View Related
Apr 29, 2013
How to get the Snmp OID for polling the in and out utilization for the CIsco 1900 Series Router interfaces.
View 1 Replies
View Related
Nov 2, 2010
I am looking at the utilization on a Catalyst 3560-E. I am running a test with eight 1 GIGE links RXing at 95 % utilization. All of the traffic is going to a TenGigE port. The device on the TenGigE port is echoing back all of the traffic received, so the 1 GIG links are TXing at 95% as well.When I do a "show controllers utilization", the port utilization numbers are correct, but the fabric utilization is higher than I would expect. The fabric should be 128 gigbits / second in this switch, and there is 7.6 gigabits TX/RX to the ten gig port. The fabric utilization is at 49%. I would expect 7.6 / 128 = 5.9% or possible double that. [code]
View 8 Replies
View Related
Feb 23, 2013
we have 2811 router with multiple servers connected to it's lan from which there are monitoring servers in between , the router suffers always from high cpu utilization
configuration has alot of ACLs & NAT & IPSEC Tunnel with wan bandwidth 20 M? Is there any method to reduce the high CPU utilization shown below !!
CPU utilization for five seconds: 90%/80%; one minute: 93%; five minutes: 90%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
104 737029848 427864243 1722 5.45% 5.65% 5.65% 0 IP Input
253 63392216 11081854 5720 1.04% 1.15% 1.12% 0 IP NAT Ager
260 82602372 137425723 601 0.64% 0.64% 0.66% 0 PDU DISPATCHER
[code]....
View 4 Replies
View Related
