Cisco Switching/Routing ::7010 - How To Configure DHCP
Aug 9, 2012I have couple of questions about Nexus 7010 configuration. how do we configure DHCP like the following example. [code]
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Nexus 7010 New Users Were Not Getting Ip Address From Dhcp Server
Jun 8, 2013We have 2 nexus 7010 switches configured with HSRP in the network. For all the vlans core1 is Master and Core2 is standby. In the current setup we have external dhcp server and dhcp relay is configured for all the vlans on Master and standby switch. The setup is running the IOS 5.2
Activity Done: During the Maintainacne activity, we isolated core1 switch in the network by disabling the vpc/keepalive and all the uplinks from access switch. The core2 switch was master for all the vlans.
Issue observed: It has been observed that new users were not getting ip address from the dhcp server. The ethereal capture showed that dhcp server was not getting the dhcp requests from the core2 switch. We disabled the dhcp feature in core2 and enabled again with dhcp relay again configured on vlan interfaces .even after doing this no change was observed in behaviour. Finally we got core1 back in network by enabling all the links.
Observation: The moment VPC link came up between the core switches, users started getting ip's from dhcp. Then we started enabling all the uplinks on core1.Core1 again become master for all the vlans and users continued getting ip’s. Network running fine.
Further Testing
1. For one of the vlan, core 2 switch has been made primary and for new users checked the dhcp functionality and it was working fine. The aim was to identify if anything wrong on core 2 related to dhcp relay
2.Again we changed the priority for this vlan and made core1 master for the same. This time we disabled this vlan on core1 and tried new user with core 2 became master and dhcp functionality worked fine for new user. Actually in this case we have simulated the same behaviour when we observed the issue with only difference of VPC was not available during the issue time as core 1 was isolated form network
Inputs needed.
Is there any known behaviour for dhcp functionality when VPC is unavailable? If we see the test scenario2 (wherein core1 was master for the vlan and we disable this vlan on core 1 and core 2 was able to relay dhcp requests for new users in this vlan.) it was actually same as scenario we observed during issue time..
Cisco Switching/Routing :: Configure 881 Router To Act As DHCP Server?
Jul 9, 2012Is it possible to configure an 881 router to act as a DHCP server to 4 VLAN's each with a different scopes all through a single ethernet interface?
View 2 Replies View RelatedCisco Switching/Routing :: How To Configure Dns / Dhcp In Switch 3860
Mar 18, 2010am having a switch 3860 it is configured dhcp , dns i want to change those dhcp , dns, what are the command that is use to reconfigure it
View 1 Replies View RelatedCisco Switching/Routing :: 3560X Configure DHCP On Switch
Apr 29, 2012I have Cisco 3560X L3 switch and i need to configure DHCP on this switch. I have already configured below mentioned VLANs
VLAN 10 - 192.168.8.254 (USER VLAN)
VLAN 20 - 192.168.152.254 (REMOTE & VPN USERS VLAN)
VLAN 30 - 192.168.0.254 (SERVER VLAN)
After configuring DHCP, all the users needs to get IP from USER VLAN and all the servers should get IP from SERVER VLAN. If yes, what are the steps as I am very new in this kind of configuration.
Cisco Switching/Routing :: C3750 - How To Configure 2 DHCP Servers For Two User Vlans
May 1, 2012I can't seem to find any info on how to configure 2 DHCP server pools on a C3750, to use with 2 user vlans. The purpose is that users in vlan 1 should get an IP address from DHCP server1, and users in vlan 2 should get an IP address from DHCP server2. Both DHCP servers are configured in a stack of C3750 switches, which acts a a L2 switch.
View 2 Replies View RelatedCisco Switching/Routing :: Catalyst 2960 / Configure Automatically Switch Over DHCP?
Jun 12, 2013I Have a problem I'm trying to configure automatically my switch over ther DHCP when I start the switch it request an IP from the DHCP from here everythings is fine but it does nothing more,indeed I put on my dhcp the option 66 and 67 which is an adress of my TFTP server and a file to download and the switch seems not to understand theses options , I tried my dhcp with a cisco airport and everythings works fine the File from the TFTP is automatically downloaded into the airport...There is an option to add or am I missing something in order to make it work with my switch ?
My switch : Catalyst 2960IOS VER : 12.2(55)SE5
Cisco Switching/Routing :: Configure Two 3845 Routers To Act As DHCP Server / Relay?
Feb 14, 2012I am trying to configure two 3845 routers to act as dhcp server and dhcp relay. Clients are connected to the router that relays all dhcp requests to the vrf instance which is used to connect it to the router wich is running dhcp server.
Router1
ip vrf dhcp_dns
rd 8:1
int gi0/0
ip vrf forwarding dhcp_dns
ip address 192.168.200.5 255.255.255.248
[code]...
So far I can see dhcp requests coming from the R1 and dhcp server on R2 replies with the dhcp offer but PC is not getting any ip.
Cisco Switching/Routing :: 3550 - Configure Firewall DHCP Server Through 10.1.1.0 Connection?
Oct 2, 2012Is there a way to configure a DHCP server for my internal subnet of 192.168.20.1 which is on a 3550 layer 3 switch from my 5505 ASA Firewall.My subnet of 10.1.1.0/30 is connecting my 5505 to 3550. All I'm trying to do is run a DHCP server down to my hosts. The only options on ASA 5505 is
dhcpd address 192.168.20.1 - 192.168.20.254 outside or inside, which conflicts with my subnet of 10.1.1.0 used to connect my internal subnet of 192.168.20.1 for the whole network.
When I used my router it did not need the (inside, outside) keywords and just an ip helper-address command. How do I configure my my firewall DHCP server to propagate the 192.168.20.0 network through my 10.1.1.0 connection.
Cisco Switching/Routing :: Configure 2960 8 Port Switch With DHCP Server?
Jun 24, 2012I need to configure a Cisco 2960 switch as a DHCP server. The current IP address will be on a different seed than the DHCP addresses. i.e.
Switch IP = 10.1.2.3, GW = 10.1.2.1, Subnet = 255.255.255.0
DHCP addresses would be 192.168.1.1 - 200, GW=???? (10.1.2.3?) and subnet would be 255.255.255.0
Cisco Switching/Routing :: Missing Commands Using DHCP / TFTP To Configure 3945 Router
Apr 10, 2012I am using DHCP/TFTP to autoconfigure a 3945 router. The router properly obtains an IP address and finds the correct TFTP server. The issue lies in the download of the configuration file from the TFTP server. The router downloads the file, gives the "Ok" message, and prompts you to press Return to get started. When I view the running-config, several commands are missing from the Serial 0/0/0 section (HWIC-2T). If I modify the config file on the TFTP server to use Serial 0/0/1 instead and repeat the process, the configuration file loads without any issues and Serial 0/0/1 has all of the commands.
I also tried moving syntax around in my config file, but the end result is still the same. If I use Serial0/0/0 - I don't get all of the commands. If I use Serial 0/0/1, I do.
Cisco Switching/Routing :: Configure 3560 To Force Client To Get IP By DHCP Relay Server?
Jul 30, 2012How to configure cisco 3560 to force the client only can get ip by dhcp-relay server ?
The company i am working in has 5 vlans which have been set an lay-3 switch(3560), uses the dhcp-relay server .(in svi configuration: ip helper-address X.X.X.X) well , that works ok~
Now , I got my problem: I need to force the client only can get ip by dhcp-relay server, that means if anyone set static IP manunally , he can't really access to anywhere (to provent anyone set static IP with malignancy )
I know if a h3c router , how to set this configuration n svi configuration : dhcp relay security address-check enable )
the how to configure on a cisco 3560 ?
Cisco Switching/Routing :: Nexus 7010 / VSS - Does It Support Virtual Switching?
Apr 9, 2010Does the nexus 7010 support virtual switching yet? All of the posts I have found from about a year ago say that it is going to be supported, but there were no dates listed. I heard the same thing from Cisco a while back, but haven't followed up with it.If it is supported finally are there any configuration guides available for it?
View 7 Replies View RelatedCisco Switching/Routing :: Nexus 7010 - Inter-VLAN Routing On Multilayer VPC Environment
Feb 16, 2011you find attached my network architecture with 2 Nexus 7010 on core layer and 2 Nexus 5020 on distribution layer, each one with 1 N2148T fabric extender switch. PC-A1 and PC-A2 are connected to one N2148T, PC-B1 is connected to the other N2148T. Nexus-7000-1 is HSRP Active for all VLANs, Nexus-7000-2 is HSRP standby. PC-A1 and PC-A2 are connected to VLAN A, PC-B1 is connected to VLAN B. PC-A1 and PC-A2 have the same default gateway correspondent to IP HSRP on VLAN A. It happens that PC-A1 is able to ping PC-B1 while PC-A2 is unable to ping PC-B1. If I issue a traceroute from PC-A2 I see Nexus-7000-2’s physical IP address as the first hop even if Nexus-7000-2 is HSRP standby. After the first hop the traceroute is lost. If I shutdown Port-channel 20 on Nexus-5000-2, PC-A2 starts to ping PC-B1.I can’t understand what’s wrong in this architecture.
View 6 Replies View RelatedCisco Switching/Routing :: 7010 - How To Add Two Nexus 5K In DC
Feb 18, 2013This is regarding Nexus core switch 7010. We are already running two nexus 7K with ten Nexus 5k. Currently we are going to add two new Nexus 5k in our DC. In the 7K we already running two VDC's.
View 8 Replies View RelatedCisco Switching/Routing :: Nexus 7010 / 5510 - Run OSPF As Layer 3 Routing Protocol Between VPC Peer Links
Mar 25, 2012I have an environment where i have two nexus 7010 switches, along with 2 nexus 5510's. I need to run OSPF as a layer 3 routing protocol between the vpc peer links. I have 1 link being used as a keep alive link, and 3 other links being used as a VpC link.
1) Is it best to configure a separate Vpc VLAN i.e 1010
2) Is it best to configure a vrf context keep-alive
3) just have the management address as the peer ip's.
Cisco Switching/Routing :: Connecting Nexus 7010 VDC With VPC
Jan 29, 2013In our LAN network design, we have two Nexus 7010 switches on the core connected via vPC. Then LAN access switches are directly connected to the Core Nexus switches via regular port channels on the 3750's and vPC on Nexus. The core Nexus switches will be linked to an existing LAN network and the applications will be progressively migrated from the old to the new network.In this scenario, three VDCs are planned to be configured on the Nexus - One for the Interconnect (and WAN at a later stage), one for the LAN/local services and one for the building facilities/local services.
View 5 Replies View RelatedCisco Switching/Routing :: Upgrade Nexus 7010 From 4.2(4) To 6.1(1)
Jun 11, 2013I'm about to perform an upgrade on two Nexus 7010 switches per above. Can I directly upgrade or, do I need to go from version 4 to 5.x and then to 6??
SA7001# dir bootflash:
518 Jan 10 00:37:51 2008 TBM14107479_136878179.lic
15830 Jun 06 11:50:11 2013 dcnm-10.25.32.10-ckpnt.cfg
16384 Jan 09 23:25:25 2008 lost+found(code)
Cisco Switching/Routing :: Logging In Nexus 7010 6.x?
Sep 19, 2012We recently replaced our core switch from a non-cisco vendor with a Nexus 7010. With our old core switch, I had the ability to log changes to the ARP table. So if there was a dhcp conflict or a vMotion event, it would show up in the "show log" output. I've not found a way to do that with the Nexus switch - or at least no way to view the log. I have the command: logging level arp 6
View 8 Replies View RelatedCisco Switching/Routing :: 6509 - Configure Multiple Dhcp Pools On Switch For Multiple VLANs
Mar 9, 2010Is it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 Replies View RelatedCisco Switching/Routing :: Nexus 7010 Dual Sup ISSU
Aug 7, 2012I have to upgrade a Nexus 7010 with dual Sup engines from 4.2(4) to 5.2 and am hoping it could be an ISSU. We are fine with an outage window.To upgrade from 4.2(4) to 5.2(5) I'll have to do a multi hop upgrade from 4.2(4) - 4.2(6) - 5.2(5) and each hop would take 40-60 minutes.do I spend 40-60 minutes for each hop, or just do a disruptive upgrade straight from 4.2(4) to 5.2(5)? Like I said, we are fine with an outage window.
View 2 Replies View RelatedCisco Switching/Routing :: Does Nexus 7010 Supports NAT64
May 1, 2012Does Cisco Nexus 7010 supports NAT64; the image that I am using is :-
Software
BIOS: version 3.22.0
kickstart: version 5.2(4)
system: version 5.2(4)
BIOS compile time: 02/20/10
kickstart image file is: bootflash:///n7000-s1-kickstart.5.2.4.bin
kickstart compile time: 12/25/2020 12:00:00 [03/08/2012 03:58:13]
system image file is: bootflash:///n7000-s1-dk9.5.2.4.bin
Cisco Switching/Routing :: Nexus 7010 Module Failure?
Apr 11, 2012I'm currently getting a Nexus hardware failure at present.
switch %MODULE-2-MOD_DIAG_FAIL: Module 8 reported failure due to DEVICE POST/DIAG FAILURE in device 48
Cisco Switching/Routing :: Surges In Nexus 7010 Latency
Dec 2, 2011I just deployed a nexus 7010 switch at a server farm. after deployment, it was notices that there are surges in latency across the network. The default gateway was then moved to the nexus, with this pinging from an host on the same subnet there is intermitent burst is latency
NEXUS>>>>>Server
Ping of about 80ms and sometimes even times out.
To me, this is strange.
NX-OS Version is 5-02a
Cisco Switching/Routing :: Creating VPC On Single Nexus 7010?
Jan 6, 2013I'm looking to see if it is possible to run a vPC between to vDC's on a single 7010? We have a Production setup that runs dual 7010's with vPC's between the chassis but in our lab we only have a single 7010 with a 32 port 10gig module. I was thinking that maybe we could create 4 vDC's on the 7010 and run a vPC between the vDC's.
View 2 Replies View RelatedCisco Switching/Routing :: Nexus 7010 NX-OS 5.2 Netflow FPS Information
May 22, 2012How to get a summary of netflow statistics on NX-OS? On IOS you could do sh ip cache flow which would show what I need? Can't find a similar command on the Nexus Platform.
View 4 Replies View RelatedCisco Switching/Routing :: Nexus 7010 Install New Supervisor
Sep 20, 2012We will install a new Supervisor Engine in our Nexus 7010.One Supervisor Engine is already installed an 1Year old.So the Problem is that both Supervisor Engines may have different NX-OS version.Could this lead to a problem?Does the installed Supervisor Engine "udate" the newer Supervisor engine?
View 3 Replies View RelatedCisco Switching/Routing :: Vrf With Hsrp In Nexus 7010 Version 6.0
Nov 24, 2012i have a big problem because i configure a vlans with vrf and HSRP but, when i do "show hsrp brief", dont show this interfaces and, i can ping virtual IP. it seems hsrp dont work.
SWSERVSCAMILO_N7010_A#
interface Vlan405
description smsc-fwatlas1
no shutdown
[Code] ....
Cisco Switching/Routing :: Management Interface On Nexus 7010?
Apr 28, 2013We have a couple of Nexus 7010's split into Core and Distribution VDCs. MGMT0 interfaces on each of the Nexus VDC's (including the Admin VDC) are configured with different IP address, but on the same subnet i.e 10.10.10.1/24 for admin, 10.10.10.2/24 for Core and 10.10.10.3/24 for Distribution. The MGMT 0 physical port on each Nexus is connected to a physical gig port on a 3750 X switch, and the 3750X has uplinks back to the Nexus configured for vPC.
When i ssh to the VDC MGMT0 IPs from the 3750X, i can access each of these VDCs without any problems. But if i enable routing on each of these links(OSPF) and advertise it to the WAN, i cannot see these routes advertised and also cannot see any of these routes in the local routing table.Just wondering if i have to enable these links on a VLAN and then advertise it to the WAN..But if this the case, VLANs cannot be created on the Admin(default VDC).
Cisco Switching/Routing :: Nexus 7010 And Connection With EIGRP
Mar 20, 2012We have, for nearly 4 years, used EIGRP on our 6513 to make use of two unequal links to our branch offices. This worked because we could use the variance command and cause EIGRP to insert two routes into the table, one from each carrier. Thus it was we could balance the load to each one with a ratio similar to the ratio of the bandwidth of Link A to Link B.
We just purchased 2 Nexus 7010's to replace our single 6513 core.After much consternation we have found from our Ciscio SE that the Nexus 6.0.2 software rendition of EIGRP does not support variance.
Why would Cisco take their own propriatary protocol and then gut it by removing features? I'm quite ready to send these Nexus boxes back in favor of a newer 6500 series. MEC doesn't work like it is supposed to and the show-tech runs for over 24 hours without ever finishing (and this we can repeat on both boxes, multiple times).
We've opened a tac case but I just wondered for any work around for the 'variance' command?
Cisco Switching/Routing :: Nexus 7010 Radius Authentication
Jan 19, 2013I am facing issue with nexus 7010 login authentication by radius server. I have two nexus 7010, one of them is working perfectly. Other taking long time to authenticate. If i use local database to login it works perfectly. It works fine also if i login from console using radius for authentication.
View 1 Replies View RelatedCisco Switching/Routing :: Nexus 7010 - How To Block SSH Access On SVI Interfaces
Jun 4, 2012I use Nexus 7010 as our layer 3 router.I have ssh feature turned on so I can manage it from the management interface. I just found out that users can use putty to ssh to the local SVI interface of the NEXUS. Although they still need username and password to login but we dont want them even able to bring up the welcome screen.Example, user's IP is : 172.16.25.100 , they can ssh to 172.16.25.1 which is the NX SVI interface.
View 1 Replies View RelatedCisco Switching/Routing :: Jumbo Frames Dropped On Nexus 7010?
Jul 5, 2012I believe i've enable jumbo frames on our Nexus 7010, one in each data-centre.
system jumbomtu 9216. Also on the interfaces mtu 9216. And can see MTU 9216 bytes, BW 20000000 Kbit, DLY 10 usec on the port-channel between them. Though when i ping between vlans at each site with large packets i get 30% drops and if i set the DF bit in IP header to yes - 100% loss.
8798 bytes from 10.200.12.2: icmp_seq=19 ttl=254 time=8.024 ms --- 10.200.12.2 ping statistics ---20 packets transmitted, 14 packets received, 30.00% packet loss