Cisco Switching/Routing :: C1811 - Isr Max Throughput When Not Running Ipsec Site Vpn?
Dec 12, 2012What is the c1811 isr max throughput when not running ipsec site vpn.
View 1 RepliesWhat is the c1811 isr max throughput when not running ipsec site vpn.
View 1 RepliesI am trying to set up a site to site ipsec connection. AT site A, I have Vlan's 652-10.55.216.0/24, Vlan653 -10.55.217.0/24, Vlan 654-10.55.217.0/24 and Vlan655-10.55.219.0/24 and at site B, Vlan650-10.55.214.0/24 and Vlan651-10.55.215.0/24.The problem is that I am unable to get any associations when i do a "sh crypto isakmp sa"/"sh crypto ipsec sa" on either router at each site.I am also unable to ping by pluging in a laptop into the site at each site. Laptop at site A is set to access vlan 655 and laptop at site B is set to acess vlan 651. I can ping all the devices from one end to the other.I have turned on debug crypto isakmp, debug crypto ipsec, debug crypto ipsec errors but dont get anything at all as output.I have attached the sh run for each router Cisco (1941/K9) and switch (Catalyst 3750) at each site.
View 4 Replies View RelatedI have an ASA 5525 and need to configure site to site ipsec vpn to 3 peers. I currently have an existing /28 public address from my ISP that is used by other services.Is there a way to use this existing ip range to configure IPSEC tunnels to 3 peers ?
View 10 Replies View RelatedThe scenario where a Site to Site VPN tunnel has been established between Site A and Site B. Lan on Site A can ping Lan on Site B. My problem is a Printer behind Site B needs to be accessed by using the WAN IP address of Site A. Also i could not ping the remote lan or printer from the router.
Below are my configure on the Cisco 877 in site A.
Building configuration...
Current configuration : 5425 bytes
!
! Last configuration change at 15:09:21 PCTime Fri Jun 15 2012 by admin01
!
version 12.4
no service pad
[code]....
What are the possibilities that exist for running a site to site vpn in our environment with the following infrastructure Cisco ASA 5520 - running on a multiple context mode
-Cisco 3750 switches
-Microsoft TMG
I believe these options are limited in terms of providing end point for VPN.Is there a VPN module that we can buy for 5520 to run IPSEC VPN?
I have a few questions:
1- Configure a Site to Site VPN between a pix506E running code 6.3 and a ASA5540 running code 8.4.2?
2- Should I expect any issues with the tunnel or ACL compatibility wise?
3- I had some issues between a ASA5505 running 8.4.2 and a Pix515E running 8.0.4 the tunnel would not go up.
I configurated Ipsec vpn at asa 5510. my inside ip 192.168.10.156my public ip: 85.x.x.xmy peer ip : 62.x.x.x
the project is that:
the remote site want the interesting traffic like that:
source ip 172.16.1.104 can access destination ip 10.0.154.27
My inside ip is 192.168.10.0/0 and i can not to change it 172.16.1.0/24 and i can not to add this ip at my network.
I have two Cisco routers - 2911 in HQ and RV180 in branch office. Because in HQ LAN network I have some development servers, to which guys from branch office need to have acces, I decided to setup VPN site-to-site between HQ and branch office. Everything went quite smoothly, on both devices I see, that ipsec connection is established. Unfortunately I am not able to ping resources from one network to other one and vice versa. Below is the configuration of 2911 router (I skipped som unimportant (imho) configuration directives) :
crypto isakmp policy 1
encr 3des
hash md5
[Code].....
With à customer we have à site to site VPN connection. In this tunnel there is one subnet routed with a 3des-sha encryption / hash. Now the want to add a new subnet in this tunnel, but with a AES-128 / MD5 encryption / hash. Is it correct if we make a new crypto map with a higher seq. number?
View 5 Replies View Relatedim drawing a blank trying to setup a site to site connection with a 5505 ASA using ipsec and isakmp.i have the pre shared key as well as the external address of the other end of the tunnel but do not remember what the commands are to setup the crypto map and isakmp.
View 7 Replies View RelatedWe have a scenario where the Cisco ASA 5505 will be one end of a site-to-site VPN. The same ASA 5505 also allows Client VPN connection. The question is around IP pooling. If I assign a pool of IP's (192.168.1.20 - 192.168.1.30) for Client VPN connections - do I need to be sure that those same IP's are not used on the other side of site-to-site VPN ?
There could be PC's/Servers running 192.168.1.0/24 on the other side of site-to-site VPN. Would this cause an address conflict ?
I have configured Ipsec vpn tunnel beetween two routers (from site A to site B) over untrusted internet connection by cisco 3825 routers and i can successfully access both of this routers. But now i need to access internet on site B router sitting on site A router. So that if i run traceroute from A site machine then the gateway by which internet passing through shows the ip of site B.
The Architecture of our both site routers :
Site A 10.1.11.0-----Router A 172.18.12.1-----VPN tunnel----Router B 172.18.12.2-----Site B 10.4.11.0
/////Create IKE policy
crypto isakmp policy 1
encr aes
authentication pre-share
group 2
[Code] .....
How can I NAT the same set of four hosts and give them access to two different networks across an IPSEC site-to-site VPN tunnel? I'm using an ASA5520 running 8.04.
I have four hosts say: 10.240.1.1-10.240.1.4
They need access to two different networks:
205.100.150.0
140.175.200.0
I woud like to NAT them as something like:
7.5.210.1
7.5.210.2
7.5.210.3
7.5.210.4
We have configured a site to site tunnel from our ASA to another organizations Cisco 3030. It appears to have just one way initiation. We can do a ping to a device on the remote site and it will ping just fine. however, when the tunnel needs to be initiated from the remote site, it will not work until we have initiated the tunnel and then everything works.
I continue to see Error processing payload: Payload ID: 1 errors on the ASDM logs.It appears that all the configuration is in place because we can in fact establish the IPSec tunnel unidirectional. And once established, traffic can flow bidirectional.
I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: [code]
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505. [code]
All these remote networks are at the Main Site Clavister Firewall.
I have a situation where the site-to-site tunnel is already established using PPTP IPSec VPN with non Cisco Gateways terminating the link on each end. These non Cisco Gateways do not support L2TP tunneling, and there is no plan to change them.Beyond the Gateways on both ends, we have a Cisco 4500 series switch. We need to forward the 802.1q tagged VLANs between the two sites. Is it possible to use 802.1Q tunneling in this case, going via a PPTP tunnel ?
Cisco's setup uses dot1q-tunnel over a L2protocol-tunnel to preserve the original client VLAN tagging, so does this mean that the only option we have is to setup a L2TP tunnel at the Cisco device endpoints, and have that tunnel go through the existing PPTP tunnel (established between the 2 non Cisco VPN Gateways) ?
recently we had some performance issues with C2811 which caused us to do some lab testing. For testing we used also C1812. The results were quite surprising for us, as the C1812 appeared to be more efficient than C2811. Below you can see the lab scenario and results.
1. Why C2811 is performing worse than C1812?
2. Is there any official Cisco reference stating what are the max VPN throughputs of certain platforms/models? (we consider migration to C2900 platform and would like to choose the right model)
[URL]
as presented on the small diag:
All routers had enabled onboard hw VPN modules and SEC/K9 IOS ver. Configuration was very simple and beside encryption there were also GRE tunnels configured and EIGRP process for routing between "remote LANs". Part of conf responsible for encryption:
crypto isakmp policy 10 encr aes 256 authentication pre-share group 5 lifetime 3600crypto isakmp key ......... address ......... no-xauth!crypto ipsec transform-set SHA-AES256 esp-aes 256 esp-sha-hmac
crypto map VPN 90 ipsec-isakmp set peer ......... set transform-set SHA-AES256 set pfs group5 match address .........
TEST RESULTS
Cisco 1812Cisco 2811iperf generated BW [bps]WAN if BW (max of 30s avgs) [bps]CPU usage (max of 5s avgs)WAN if BW (max of 30s avgs) [bps]CPU usage (max of 5s avgs)500k--540k5%1M1,1M3%1,2M8%2M2,1M4%2,3M14%5M5,4M10%5,7M34%10M10,6M20%11,5M65%15M15,8M28%17M96%16M--17,2M99%25M27M48%--35M38M64%--45M48,2M72%--53M60,8M88%--59M67M94%--61M72M97%--
My requirment is Clients from site A should access the Internet from site B (B will be providing internet to site A), So I have configured Ipsec vpn tunnel beetween two routers (from site A to site B) over untrusted internet connection by cisco 3825 routers and i can successfully access both of this routers.I have configured a client machine in site A and configured gateway of this client is 10.1.11.254 but dont have internet there.
View 2 Replies View RelatedI have a Cisco 2911 router and a Cisco RV 120W router and i would like to establish a VPN tunnel between theese two. I have defined the settings on the Cisco RV 120W router and i just want the Cisco 2911 to follow those. setting up a connection with Cisco IOS.
View 1 Replies View RelatedSite A has an ASA 5510 and a single internet connection.Site B has two internet connections (primary and backup). If Site B also has an ASA, I can configure Site A's ASA to deal with a failover at Site B (set peer 1.1.1.1 2.2.2.2). Does this work if Site B has an IOS router instead of an ASA? In other words will "set peer 1.1.1.1 2.2.2.2" on the ASA work when it's talking to IOS on the other end?
View 15 Replies View RelatedQuestion on ASA VPN tunnels. I have one ASA 5510 in our corporate office, I have two subnets in our corporate office that are configured in the ASA in a Object group. I have a site to site IPSEC tunnel already up and that has been working. I am trying to set up another site to site IPSEC tunnel to a different location that will need to be setup to access the same two subnets. I'm not sure if this can be setup or not, I think I had a problem with setting up two tunnels that were trying to connect to the same subnet but that was between the same two ASA's. Anyways the new tunnel to a new site is not coming up and I want to make sure it is not the subnet issue. The current working tunnel is between two ASA 5510's, the new tunnel we are trying to build is between the ASA and a Sonicwall firewall.
View 3 Replies View RelatedI am having issues getting my ASA 5540 at site A, to pass TFTP and SYSLOG from itself across the IPSEC tunnel to our SYSMON servers (Syslog and TFTP) that live at site B. I have followed the suggestions of other threads and I am still not getting anywhere. Here is a quick topology diagram.
View 6 Replies View RelatedCan i know cisco 2800 router can support how many site-to-site ipsec tunnel without vpn module?
View 2 Replies View RelatedI have cisco pix connected at the edge of my GPRS network. Inside is the GPRS core network and outside is the ISP.On cisco pix, i have site to site IPSec configured between my inside GPRS network and Blackberry servers. for blackberry services.Using the ASDM I can see the total number of packets in and out on this site to site IPSec, but if I want to measure the trand of the bandwidth utilisation over this IPSec, per sec, then how can I do this? I have PRTG traffic monitoring, through which I did try, several MIB (listed below) but still not able to find the correct way. how can I get the measurement for the IPSec from cisco pix?
View 1 Replies View RelatedI cannot get it to work : if interesting traffic comes ffrom the IPSO side, the box would not even try to set up the tunnel. and If it comes fomr the ASA side, the box attempts to do so but it with this strange message : AM_WAIT_MSG2
View 3 Replies View RelatedI recently faced an issue at work. Clients want to make ipsec site-to-site vpn redundant. I have 2-asa-5520 working in a stack. Is it possible to configure site-to-site vpn in a redundant mode, like first peer ip address is x.x.x.x and secondary is y.y.y.y (backup) ?
View 1 Replies View Relatedcurrently I have a Cisco 2921 router and I have one active site-to-site VPN connection through the internet.my question is; how I can create another Ipsec site-to-site VPN connection ? I have to keep the 1st VPN connection active.
View 11 Replies View Relatedyou can configure a cisco 1905 router with vpn ipsec site-to-site in an aggressive mode? If so, any link to what I do? The VPN works well, but on site A, I had to configure a crypto map associating the IP address for site B (wich is dynamic), so if the connection on site B broken, I will have to configure another crypto map.
The scenario is:
Site A - ASA 5510 configured as a VPN concentrator and firewall for enterprise.
Site B - Cisco 1905 connected to Internet through a ADSL through a dynamic IP address and starting connection to Site A, bellow is the configuration:
crypto isakmp policy 10
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp key xxxxxxxxxxxx address W.X.Y.Z
[code]....
I have a very basic lab site to site vpn setup where I have a ASA 5505 running v7.2(4) on one side and a cisco 2811 on the other side.
What's my issue?
I can't seem to ping from cisco router to the 'inside' network of ASA (see config below) and can't seem to ping from ASA packets leaving the 'inside' interface to cisco router even w/ an ICMP ACL permit outside in. However I'm able to ping within ASA inside network & ping cisco 2811 side w/ packets leaving ASA 'outside' interface just fine.
example:
-------
ciscoasa# ping inside 10.20.20.1 (to cisco loopback1 from ASA inside)
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.20.20.1, timeout is 2 seconds:
[Code].....
I am experiencing slow throughput on a L2L IPsec tunnel that we have between one of our offices on the west coast (WC) US and another on the east coast (EC) US. The tunnel endpoint on the WC resides on a 5510 and a 5545x on the EC. The DIA circuit speed on the WC is 45 Mbps and 200 Mbps on the EC. The throughput of this IPsec tunnel is maxing out at approx. 4 – 5 Mbps. The utilization of the DIA circuits at both offices is under 5% when running various FTP test transfers. Both devices have low memory and CPU utilization.
We have a 2nd office on the EC (45 Mbps DIA) which I built a tunnel on a 5510 with the WC office and it is experiencing the same slow throughput. In covering all my bases we have a colocation facility on the WC and in building a tunnel between the 2 WC offices I WAS seeing close to full line rate speeds over the tunnel. Additionally, I built a tunnel between the 2 EC offices and I saw full line rate speeds. With the physical distance between the WC & EC offices I would expect some loss in throughput speeds but I would not expect it to drop as low as 4 – 5 Mbps. In thinking something may be up with the 5510 in our WC office we shipped a 5505 to the WC office and we built the same IPsec tunnels on it and it is experiencing the same.
In working with our support vendor to try and solve the WC <-> EC throughput issue they had me change the MTU, TCP mss, DF-bit, types of encryption/hash on the IPsec tunnel but nothing has resolved it. We are not showing fragmentation or PMTU issues on the tunnel. In contacting the ISP of our WC office they mentioned that they do not have any type or rate limiting in place. Our WC ISP had a CCIE review our configurations but nothing was found.
I've spent 2 days already trying to get 2 ASA 5505's to connect using an IPSec vpn tunnel. I cannot seem to figure out what im doing wrong, im using 192.168.97.0 and 192.168.100.0 as my internal networks that i'm trying to connect over a directly connected link on the outside interfaces with 50.1.1.1 and 50.1.1.2 as the addresses (all /24). I also tried with and currently without NAT enabled. Here are the configs for both ASA's, the vpn config was done by the ASDM, however i have also tried the command line apporach with no success. I have followed various guides to the letter online, starting from an empty config and from factory default. I have also tried the 8.4 IOS. [code]
View 2 Replies View RelatedI am setting up a IPSEC VPN tunnel between a Cisco 2921 and ASA 550x. [code]
View 6 Replies View RelatedI want a site to site vpn ipsec tunnel there wants to use two Cisco 880 routers that are connected to a modem / router is this possible?
View 12 Replies View Related