Cisco Switching/Routing :: Unable To Upgrade Nexus 5596UP NX-OS Fan
Jul 1, 2012
We have two Cisco Nexus 5596UP switch.
We upgraded
n5000-uk9-kickstart.5.0.3.N2.1.bin (Fan speed %40) to
n5000-uk9-kickstart.5.1.3.N2.1a.bin (Fan Speed %60)
but 20% increased speed of the fans. What could be problem?
Software
BIOS: version 3.5.0
loader: version N/A
kickstart: version 5.1(3)N2(1a)
system: version 5.1(3)N2(1a)
[code]....
View 1 Replies
ADVERTISEMENT
Jun 10, 2013
I have two Nexus 5596UP that will be connected together via VPC-Peerlink. From there I want to connect both 5596UP's to a 6509-VSS via VPC.The Nexus 5596UP's will be essentially layer 2 switches, all routing will be done the 6509-VSS's.
View 2 Replies
View Related
Jan 23, 2013
When I read Nexus 5K install guide , I found the follow :The Cisco Nexus 5596UP switch has the following features: # •48 fixed 1- and 10-Gigabit Ethernet server connection ports on the back of the switch AND The 48 fixed ports support 8-, 4-, 2-, or 1-Gbps Fibre Channel transceivers and 1- or 10-Gigabit Ethernet transceivers. Does these is a conflict ?The 48 fixed port on this switch support only 1- and 10-Gigabit Ethernet or 8-, 4-, 2-, or 1-Gbps Fibre Channel and 1- or 10-Gigabit simultaneously ?
View 2 Replies
View Related
May 6, 2013
We have two Nexus switches in our network, one of them is Nexus5020 other Nexus5596UP. System image is identical on both switches 5.2(1)N1(4). When we try to setup VPC between these switches we see that all configured vlans on VPC peer link between Nexus switches are blocked by spanning tree protocol with message "Bridge Assurance Inconsistent, VPC Peer-link Inconsistent". We still can't solve this problem.
Topology:
NEXUS_5020---Peer_link(Po2)---NEXUS_5596UP
/
/
Member_link (Po100) Member_link (Po100)
/
/
SERVER
Configuration:
NEXUS_5020:
speed 1000
interface Vlan2000
no shutdown
description VPC_keepalive_link
vrf member VPC_kepalive
ip address 10.55.55.2/30
View 2 Replies
View Related
May 11, 2013
I'm trying to get the VFC up in B22-FEX blade in Dell which is connecting to Nexus 5596UP.
The message I get is
# sh int vfc1033
vfc1033 is down (Error Disabled - VLAN L2 down on Eth interface)
Bound interface is port-channel3
Hardware is Ethernet
Port WWN is 24:08:00:2a:6a:0d:db:3f
Admin port mode is F, trunk mode is on
[code]....
View 3 Replies
View Related
Feb 19, 2012
I would like to make a design with 4 Nexus 5596UP. 2 of them equipped with Layer 3 Expansion Module so they can serve as core layer and the other 2 Nexus used as Layer 2 for aggregation server layer.The 2 Nexus in the core layer will run HSRP and will peer with ISP via BGP for Internet connection The 2 Nexus in the aggregation layer will be configured as layer 2 device and have FEX and switches connected to them.What I am ensure of is how the vpc and port-channel configuration should look like between the 4 nexus. What I was thinking is to run vpc between the 2 Nexus in the aggregation layer and between the 2 Nexus in the core layer. Than I was thinking of connecting each Nexus in the aggragtion layer to both Nexus in the core layer using port-channel and vice-versa.
View 3 Replies
View Related
Jul 24, 2012
1. We would like to pre-provision a 2248TP FEX on my 5596UP (NEXUS 5596 running 5.1(3)N2(1a)). Problem is that I can't choose this FEX model. I have the choice of a 2248T or a 2248TP-E, but no 2248TP. [code]
2. on pair of NEXUS 5596 running 5.1(3)N2(1a) with a Layer-3 module installed in both.When doing Enhanced vPC - connecting all FEXs dual-homed to both 5596 - how many FEXs can I have in total ?
View 1 Replies
View Related
Feb 3, 2013
I need to upgrade my core switches at one of our locations (two 7009s with dual sups) from 6.0.1 to 6.1.2. After looking through the release notes it appears that this will be a disruptive upgrade?how long should I expect for the disruption? Are we talking a 7009 boot cycle (10 - 15 minutes) or something longer?How many disruptions can I expect? I suspect 1 per chassis during the failover to the standby but I'd like to validate.Is there any compelling reason to upgrade the EPDL? From what I can see, again from the release notes, this is only necessary with F2 cards if I were to upgrade to Sup2s . I'm in a healthcare environment and this upgrade will be affecting one of our major campuses so the more info I can get to the managers the more accepting they will be for the disruptions.
View 3 Replies
View Related
Mar 17, 2013
We have a small doubt with NX-OS version upgrade.
We are currently using version 5.2(1) on Nexus7000 C7010, We want to upgrade to 5.2.4 is it compatible or any issues with this version?
View 1 Replies
View Related
Jun 11, 2013
I'm about to perform an upgrade on two Nexus 7010 switches per above. Can I directly upgrade or, do I need to go from version 4 to 5.x and then to 6??
SA7001# dir bootflash:
518 Jan 10 00:37:51 2008 TBM14107479_136878179.lic
15830 Jun 06 11:50:11 2013 dcnm-10.25.32.10-ckpnt.cfg
16384 Jan 09 23:25:25 2008 lost+found(code)
View 3 Replies
View Related
May 15, 2013
I'm planning to upgrade N5K from 5.1(3)N2(1b) to 5.2(1)N1(4)."sh install all impact kickstart bootflash:n5000-uk9-kickstart.5.2.1.N1.4.bin system bootflash:n5000-uk9.5.2.1.N1.4.bin"reports:
...
Compatibility check is done:
Module bootable Impact Install-type Reason
------ -------- -------------- ------------ ------
1 yes non-disruptive reset
...
Is the upgrade really non-disruptive?
View 1 Replies
View Related
Jan 3, 2012
i need to do EPLD upgrade. on a couple of Nexus 7000 with only 1 10Gb card per Switch and 2 peer-link on this card. Can you tell me what's happening when the 10GB card on the vpc secondary role Switch will be EPLD upgraded.
View 6 Replies
View Related
Jun 26, 2012
I would like to perform nondisruptive upgrades on two Cisco Nexus 5010s that currently run NX-OS version 4.1(3)N2(1) to Release 5.1(3)N2(1a). Is this possible? Or, do I need to upgrade to Release 5.0(2)N1(1) first?
View 3 Replies
View Related
Jun 11, 2012
The Nexus 5548 is running 5.1.3.N2.1a and has the L3 daughter card (N55-D160L3)I have the EIGRP feature enabled. By the way, when doing a 'sh feature' four EIGRP features show up like this: [code] To create the L3 SVI, I go into config mode and attempt to type 'interface vlan 10'. but this doesn't work. These are the only options under the keyword 'interface':
- ethernet
- loopback
- mgmt
- port-channel
I must be missing something simple but can't seem to see what that is. What do I need to do in order to create an L3 SVI on this 5548?
View 1 Replies
View Related
May 1, 2013
Interestingly enough I've seen about 3-4 posts with the exact same problem and yet not a single one is ever answered.. The task is simple:
"username USER password 5 SOMEPASS role network-admin"
It consistently outputs: "String failed to match token pattern at '^' marker." - always the carat is at the first character in whatever password I input. I've ensured passwords I input meet the conditions of "password strength-check" and I have also disabled this feature and repeated with numerous passwords to no effect.
View 7 Replies
View Related
Jun 23, 2012
I am not able to create more than 256 VLAN in Cisco Nexus 5010 switch. While creating I am getting "No VLAN resources available for VLAN creation" Details below -
Switch model - 5010
Software : NX OS 4.0 (1a)
Error Message:
Nexus_5010(config)# vlan 417
ERROR: No VLAN resource available for VLAN creation.
View 5 Replies
View Related
Jul 10, 2012
Yesterday I configured the 7010 Nexus switch. I created a VDC and allocated few ports and configured VLAN for testing. After enabling feature interface-vlan i was allowed to configured L3 interface for the vlan. I assigned ip address and connected few server to check the reachability but it says Destination Host Unreachable.
NX OS Ver : n7000-s1-dk9.5.2.4.bin
Configuration of the VDC below.
feature telnet
feature udld
feature interface-vlan
feature lacp
[Code]....
View 2 Replies
View Related
Jan 28, 2013
Is there any challenge to upgrade core switch 6500 series from Nexus 7009 which runs NxOS, because i have 3750X series switches connected at distribution and access layer in my network topology??
Is there any challenge if we place NxOS in core and IOS in distribution and Access layer??? how we are able to match sh run config in existing 6500 switch to Nexus 7009 NXOS?
View 9 Replies
View Related
Aug 26, 2012
I just tried to upgrade my Cisco 2600XM router from 12.3-6 IOS to 12.4-25d IOS, but I was unable to start the router with this new IOS.
flash:c2600-ipbase-mz.123-6.bin (old IOS)
flash:/c2600-ipbasek9-mz.124-25d.bin (new IOS)
=================================================================
Output sh flash
=================================================================
System flash directory:
[Code].....
View 2 Replies
View Related
Feb 23, 2011
We are facing issue of continous packet discards On nexus4001L link (int po2) to Nexus5020 switch. Nexus4001L is installed in IBM blade center server and we have FCOE enabled in this setup. [code]
View 2 Replies
View Related
Mar 15, 2013
I have been tasked to replace the existing Cat 6500 and 3750 switches by Nexus 7000 and Nexus 2000.I was told initially my boss plans to get 2 x Nexus 7000 and then eventually blow up to 4 x Nexus 7000s.For Nexus, is there a list of tasks / points that i need to consider for building the initial design?
Can i just link the Nexus 7000 like the following?
N7k-A ========= N7k-B
| |
lots of N2ks lots of N2ks
View 12 Replies
View Related
Dec 22, 2011
Struggle to find the SNMP MIBS of the Nexus 5000 FEX tranceivers.
View 3 Replies
View Related
Nov 13, 2012
we are planning a Nexus datacenter project with this layout:Our experiences with Nexus switches are not so large until now and the manuals are very extensive.Both N5K´s should be connected directly with all 4 N2K switches. I did not find a layout like this in the manuals. Only a design,where only 2 N2K are connected to one N5K, with this fex config:Now I´m not sure if it is right to make a config like this with the same slots and fex´s or with different slots and fex´s.
View 1 Replies
View Related
Apr 9, 2010
Does the nexus 7010 support virtual switching yet? All of the posts I have found from about a year ago say that it is going to be supported, but there were no dates listed. I heard the same thing from Cisco a while back, but haven't followed up with it.If it is supported finally are there any configuration guides available for it?
View 7 Replies
View Related
Oct 8, 2012
Lucien is a customer support engineer at the Cisco Technical Assistance Center. He currently works in the data center switching team supporting customers on the Cisco Nexus 5000 and 2000. He was previously a technical leader within the network management team. Lucien holds a bachelor's degree in general engineering and a master's degree in computer science from Ecole des Mines d'Ales. He also holds the following certifications: CCIE #19945 in Routing and Switching, CCDP, DCNIS, and VCP #66183
View 1 Replies
View Related
Jan 10, 2012
Can nexus 5010 supports inter v lan routing , as there is no core switch and router available in current network.
View 2 Replies
View Related
May 16, 2013
We have our Nexus as our default gateway (101.1) and the default VLAN1 is setup with two subnets 101.X and 102.X. The DHCP server is using a superscope setup to accomodate the overflow of devices requesting IPs on 101, so when 101 is consumed persons are able to obtain a 102.X IP address. The setup is basic on superscope. The issue is some times the routing to the firewall with a 102.X is not always 100%. Somedays all goes well and the 102 subnet is routed out to the firewall and its a good day. However, such as today a 102.X address is not routing as it did 24 hours ago. I am perplexed as to why this is behaving unpredicatable. Here is running-config for VLAN1 to show the 102 as secondary address to VLAN1.
View 2 Replies
View Related
Feb 16, 2011
you find attached my network architecture with 2 Nexus 7010 on core layer and 2 Nexus 5020 on distribution layer, each one with 1 N2148T fabric extender switch. PC-A1 and PC-A2 are connected to one N2148T, PC-B1 is connected to the other N2148T. Nexus-7000-1 is HSRP Active for all VLANs, Nexus-7000-2 is HSRP standby. PC-A1 and PC-A2 are connected to VLAN A, PC-B1 is connected to VLAN B. PC-A1 and PC-A2 have the same default gateway correspondent to IP HSRP on VLAN A. It happens that PC-A1 is able to ping PC-B1 while PC-A2 is unable to ping PC-B1. If I issue a traceroute from PC-A2 I see Nexus-7000-2’s physical IP address as the first hop even if Nexus-7000-2 is HSRP standby. After the first hop the traceroute is lost. If I shutdown Port-channel 20 on Nexus-5000-2, PC-A2 starts to ping PC-B1.I can’t understand what’s wrong in this architecture.
View 6 Replies
View Related
Mar 25, 2012
I have an environment where i have two nexus 7010 switches, along with 2 nexus 5510's. I need to run OSPF as a layer 3 routing protocol between the vpc peer links. I have 1 link being used as a keep alive link, and 3 other links being used as a VpC link.
1) Is it best to configure a separate Vpc VLAN i.e 1010
2) Is it best to configure a vrf context keep-alive
3) just have the management address as the peer ip's.
View 2 Replies
View Related
Feb 6, 2012
I have a pair of 5548P switches with the L3 daughter cards installed. Using the base license as I just need RIP routing. I have the two switches setup and have the RIP routing feature enabled. When I "turn on" routing using RIP I do not get any routes from my existing L3 switch (3750). I probably don't have routing setup correctly. With the 3750 IOS, I just turned on RIP with the router rip command and added a couple of network statements. On the nexus I have run router rip {instance} and left it at that. I am not getting any routes from my 3750. The 5548s are using the management ports and are connected to my existing network with L2 trunks. Does any know of a setup guide for RIP? I have used the Nexus 7000 RIP guide but still can't get it to work.
View 2 Replies
View Related
Jul 2, 2012
I''ve trying to bring up ports on a N7K-M108X2-12L card using X2-10GB-SR modules.
All ports are in a VDC and configured to accept the M1 card:
vdc_id vdc_name state mac type lc
------ -------- ----- ---------- --------- ------
2 cam-cor-csw-sfy-01 active 64:a0:e7:43:f0:c2 Ethernet m1 f1 m1xl
[Code]....
View 3 Replies
View Related
Feb 18, 2013
This is regarding Nexus core switch 7010. We are already running two nexus 7K with ten Nexus 5k. Currently we are going to add two new Nexus 5k in our DC. In the 7K we already running two VDC's.
View 8 Replies
View Related
Jun 8, 2013
The fans 1 & 2 in Module 1 on the Nexus5K are still experiencing the very high RPM and speed issue.
I have replaced the fan from another operational Nexus5K, and the fans are fine in the other Nexus. The replacement fans also have the same issues, so it is not a fan hardware issue.
There are no threshold alarms. the only log entry that is related to this is as follows:
%NOHMS-2-NOHMS_ENV_ERR_FAN_SPEED: System minor alarm in fan tray 1: fan speed is out of range on fan 1. 7950 to 12500 rpm expected. I have provided the output for both the fan detail and the temperature.
N5K-01# sh environment fan detail
Fan: --------------------------------------------------- Module Fan Airflow Speed(%) Speed(RPM) Direction --------------------------------------------------- 1 1
[Code].....
View 4 Replies
View Related