We have a small doubt with NX-OS version upgrade.
We are currently using version 5.2(1) on Nexus7000 C7010, We want to upgrade to 5.2.4 is it compatible or any issues with this version?
i have problem with device. The device Nexus7000 C7010 with System version: 4.2(1) is suddenly reload .this is cause from sh system reset-reason
CORE1-7010# sh system reset-reason
----- reset reason for Supervisor-module 6 (from Supervisor in slot 6) ---
1) At 493933 usecs after Thu Jul 19 08:47:07 2012
Reason: Reset triggered due to HA policy of Reset
Service: netstack hap reset
Version: 4.2(1)
when i see this problem related with this bug
CSCtd14544 g Details [URL]
I need to upgrade my core switches at one of our locations (two 7009s with dual sups) from 6.0.1 to 6.1.2. After looking through the release notes it appears that this will be a disruptive upgrade?how long should I expect for the disruption? Are we talking a 7009 boot cycle (10 - 15 minutes) or something longer?How many disruptions can I expect? I suspect 1 per chassis during the failover to the standby but I'd like to validate.Is there any compelling reason to upgrade the EPDL? From what I can see, again from the release notes, this is only necessary with F2 cards if I were to upgrade to Sup2s . I'm in a healthcare environment and this upgrade will be affecting one of our major campuses so the more info I can get to the managers the more accepting they will be for the disruptions.
View 3 Replies View RelatedI'm about to perform an upgrade on two Nexus 7010 switches per above. Can I directly upgrade or, do I need to go from version 4 to 5.x and then to 6??
SA7001# dir bootflash:
518 Jan 10 00:37:51 2008 TBM14107479_136878179.lic
15830 Jun 06 11:50:11 2013 dcnm-10.25.32.10-ckpnt.cfg
16384 Jan 09 23:25:25 2008 lost+found(code)
I'm planning to upgrade N5K from 5.1(3)N2(1b) to 5.2(1)N1(4)."sh install all impact kickstart bootflash:n5000-uk9-kickstart.5.2.1.N1.4.bin system bootflash:n5000-uk9.5.2.1.N1.4.bin"reports:
...
Compatibility check is done:
Module bootable Impact Install-type Reason
------ -------- -------------- ------------ ------
1 yes non-disruptive reset
...
Is the upgrade really non-disruptive?
We have two Cisco Nexus 5596UP switch.
We upgraded
n5000-uk9-kickstart.5.0.3.N2.1.bin (Fan speed %40) to
n5000-uk9-kickstart.5.1.3.N2.1a.bin (Fan Speed %60)
but 20% increased speed of the fans. What could be problem?
Software
BIOS: version 3.5.0
loader: version N/A
kickstart: version 5.1(3)N2(1a)
system: version 5.1(3)N2(1a)
[code]....
i need to do EPLD upgrade. on a couple of Nexus 7000 with only 1 10Gb card per Switch and 2 peer-link on this card. Can you tell me what's happening when the 10GB card on the vpc secondary role Switch will be EPLD upgraded.
View 6 Replies View RelatedI would like to perform nondisruptive upgrades on two Cisco Nexus 5010s that currently run NX-OS version 4.1(3)N2(1) to Release 5.1(3)N2(1a). Is this possible? Or, do I need to upgrade to Release 5.0(2)N1(1) first?
View 3 Replies View RelatedIs there any challenge to upgrade core switch 6500 series from Nexus 7009 which runs NxOS, because i have 3750X series switches connected at distribution and access layer in my network topology??
Is there any challenge if we place NxOS in core and IOS in distribution and Access layer??? how we are able to match sh run config in existing 6500 switch to Nexus 7009 NXOS?
We are facing issue of continous packet discards On nexus4001L link (int po2) to Nexus5020 switch. Nexus4001L is installed in IBM blade center server and we have FCOE enabled in this setup. [code]
View 2 Replies View RelatedI have been tasked to replace the existing Cat 6500 and 3750 switches by Nexus 7000 and Nexus 2000.I was told initially my boss plans to get 2 x Nexus 7000 and then eventually blow up to 4 x Nexus 7000s.For Nexus, is there a list of tasks / points that i need to consider for building the initial design?
Can i just link the Nexus 7000 like the following?
N7k-A ========= N7k-B
| |
lots of N2ks lots of N2ks
Struggle to find the SNMP MIBS of the Nexus 5000 FEX tranceivers.
View 3 Replies View Relatedwe are planning a Nexus datacenter project with this layout:Our experiences with Nexus switches are not so large until now and the manuals are very extensive.Both N5K´s should be connected directly with all 4 N2K switches. I did not find a layout like this in the manuals. Only a design,where only 2 N2K are connected to one N5K, with this fex config:Now I´m not sure if it is right to make a config like this with the same slots and fex´s or with different slots and fex´s.
View 1 Replies View RelatedDoes the nexus 7010 support virtual switching yet? All of the posts I have found from about a year ago say that it is going to be supported, but there were no dates listed. I heard the same thing from Cisco a while back, but haven't followed up with it.If it is supported finally are there any configuration guides available for it?
View 7 Replies View RelatedLucien is a customer support engineer at the Cisco Technical Assistance Center. He currently works in the data center switching team supporting customers on the Cisco Nexus 5000 and 2000. He was previously a technical leader within the network management team. Lucien holds a bachelor's degree in general engineering and a master's degree in computer science from Ecole des Mines d'Ales. He also holds the following certifications: CCIE #19945 in Routing and Switching, CCDP, DCNIS, and VCP #66183
View 1 Replies View RelatedCan nexus 5010 supports inter v lan routing , as there is no core switch and router available in current network.
View 2 Replies View RelatedWe have our Nexus as our default gateway (101.1) and the default VLAN1 is setup with two subnets 101.X and 102.X. The DHCP server is using a superscope setup to accomodate the overflow of devices requesting IPs on 101, so when 101 is consumed persons are able to obtain a 102.X IP address. The setup is basic on superscope. The issue is some times the routing to the firewall with a 102.X is not always 100%. Somedays all goes well and the 102 subnet is routed out to the firewall and its a good day. However, such as today a 102.X address is not routing as it did 24 hours ago. I am perplexed as to why this is behaving unpredicatable. Here is running-config for VLAN1 to show the 102 as secondary address to VLAN1.
View 2 Replies View Relatedyou find attached my network architecture with 2 Nexus 7010 on core layer and 2 Nexus 5020 on distribution layer, each one with 1 N2148T fabric extender switch. PC-A1 and PC-A2 are connected to one N2148T, PC-B1 is connected to the other N2148T. Nexus-7000-1 is HSRP Active for all VLANs, Nexus-7000-2 is HSRP standby. PC-A1 and PC-A2 are connected to VLAN A, PC-B1 is connected to VLAN B. PC-A1 and PC-A2 have the same default gateway correspondent to IP HSRP on VLAN A. It happens that PC-A1 is able to ping PC-B1 while PC-A2 is unable to ping PC-B1. If I issue a traceroute from PC-A2 I see Nexus-7000-2’s physical IP address as the first hop even if Nexus-7000-2 is HSRP standby. After the first hop the traceroute is lost. If I shutdown Port-channel 20 on Nexus-5000-2, PC-A2 starts to ping PC-B1.I can’t understand what’s wrong in this architecture.
View 6 Replies View RelatedI have an environment where i have two nexus 7010 switches, along with 2 nexus 5510's. I need to run OSPF as a layer 3 routing protocol between the vpc peer links. I have 1 link being used as a keep alive link, and 3 other links being used as a VpC link.
1) Is it best to configure a separate Vpc VLAN i.e 1010
2) Is it best to configure a vrf context keep-alive
3) just have the management address as the peer ip's.
I have a pair of 5548P switches with the L3 daughter cards installed. Using the base license as I just need RIP routing. I have the two switches setup and have the RIP routing feature enabled. When I "turn on" routing using RIP I do not get any routes from my existing L3 switch (3750). I probably don't have routing setup correctly. With the 3750 IOS, I just turned on RIP with the router rip command and added a couple of network statements. On the nexus I have run router rip {instance} and left it at that. I am not getting any routes from my 3750. The 5548s are using the management ports and are connected to my existing network with L2 trunks. Does any know of a setup guide for RIP? I have used the Nexus 7000 RIP guide but still can't get it to work.
View 2 Replies View RelatedI''ve trying to bring up ports on a N7K-M108X2-12L card using X2-10GB-SR modules.
All ports are in a VDC and configured to accept the M1 card:
vdc_id vdc_name state mac type lc
------ -------- ----- ---------- --------- ------
2 cam-cor-csw-sfy-01 active 64:a0:e7:43:f0:c2 Ethernet m1 f1 m1xl
[Code]....
This is regarding Nexus core switch 7010. We are already running two nexus 7K with ten Nexus 5k. Currently we are going to add two new Nexus 5k in our DC. In the 7K we already running two VDC's.
View 8 Replies View RelatedThe fans 1 & 2 in Module 1 on the Nexus5K are still experiencing the very high RPM and speed issue.
I have replaced the fan from another operational Nexus5K, and the fans are fine in the other Nexus. The replacement fans also have the same issues, so it is not a fan hardware issue.
There are no threshold alarms. the only log entry that is related to this is as follows:
%NOHMS-2-NOHMS_ENV_ERR_FAN_SPEED: System minor alarm in fan tray 1: fan speed is out of range on fan 1. 7950 to 12500 rpm expected. I have provided the output for both the fan detail and the temperature.
N5K-01# sh environment fan detail
Fan: --------------------------------------------------- Module Fan Airflow Speed(%) Speed(RPM) Direction --------------------------------------------------- 1 1
[Code].....
I was reading a QoS walkthrough earlier to try to solve my problem and I noticed that in IOS, you can specify "match vlan" in a class map. This is not available in NX-OS. I'm not doing any routing on the 5K so I cannot match on ACL, and port where traffic is received is a trunk sharing other types of traffic I'd like to classify elsewise.
How can I match traffic on a per-VLAN basis?
How to configure a nexus 5K?
View 3 Replies View RelatedJust upgraded Nexus 7k from 5.2.1 to 5.2.7 (just system and kickstart image and NOT epld image). but after upgrading the one of the fex(n2k) dont seem to come online (this nexus 7k has two n2k and one of them came online and working fine)
[code]....
I have a couple of Nexus 5ks that I want to put QOS on for the servers running behind it but also have voice running across it. Voice doesn't play well with jumbo frames so I'd like to put QOS only on the voice vlan.
View 1 Replies View RelatedI am working in my lab and I was adding a new L2/3 vlan
vlan 555
name test
int vlan 555
ip address 1.1.1.1/24
no shut
I have also ensured that this vlan is added to the port channel going to my Nexus5K's. I added the vlan to the 5K's and also ensured that vlan 555 is traversing the peer link. all is good there. I have also placed a device on a interface on the 2k as a access switchport on vlan 555
Here is my problem, the L3 interface will NOT come up on the 7K
LAB-DSW01# sh ip int brie
IP Interface Status for VRF "default"(1)
Interface IP Address Interface Status
Vlan555 1.1.1.1 protocol-down/link-down/admin-up
I have gone throug just about everything I can think of and I am still unable to get this L3 interface to come up. I have other L3 interfaces on this device that are configured exactly the sameway without any issue at all. All the existing interfaces are working properly, it's jut this new interface that I am trying to add.
I am running version 6.0.1 on the 7K and 5.2.1.N1.4 on the 5K.
I am trying to upgrade IOS on my Nexus7018 from version 5.12 to 5.13. I have managed on all my three out of four Nexus succesfully but one of them is keep coming with this error,
""""N1K-7018-1# install all kickstart bootflash:n7000-s1-kickstart.5.1.3.bin system bootflash:n7000-s1-kickstart.5.1.3.bin
Another install procedure may be in progress. Please try later.
how to find out which other install is running or stop any install procedure.?
Any good link that explains the NX-OS upgrade path? I am trying to go from 5.0(2a) to 5.2x.
View 1 Replies View RelatedIts required that all ports on nexus 7k should be user configurable as either 1G/10G/FcoE. Which module do i need in this case ?
View 0 Replies View RelatedWe are thinking of following classic design, would Nexus 5K can have 2 seperate connections to each VDC? Nexus 7K w/ different VDC (Internal / DMZ ) Can Nexus 5K have a VPC connection to Nexus 7K to Internal VDC as well as DMZ VDC, and seperate traffic?
View 3 Replies View RelatedI currenty have a Nexus 5010 connected to a core 3750X switch stack in a VPC trunk using 2 1Gbps links. I want to move this link to 2 10Gbps links without losing connectivity. So I want remove a 1G link and move it to 10G and then once that's up move the other 1G link to 10G hopefully without losing connectivity. So the question is, can I have a 1G and 10G link between the Nexus and 3750s in the same virtual port channel without causing problems?
View 3 Replies View Related