Cisco VPN :: Configuring VPN On A 870?
May 30, 2011if I can configure a VPN on a Cisco 870 - CISCO877 V06.I either want to confiugure this as a VPN server or for it to forward PPTP traffic to a server based with the network.
View 1 Replies
ADVERTISEMENT
Cisco :: Configuring Dynamic NAT?
Feb 23, 2011having some trouble with configuring dynamic NAT
View 15 Replies View RelatedCisco :: Pbl With GNS3 In Configuring RIP
Feb 19, 2013I'm using GNS3 in order to revise CCNA, the RIP part But I don't know why, i'v got a pbl with the routage table, especially with the metric which is wrong I don't understand wy the metric is always 1, because it should be 2 or 3 according to the network.
View 5 Replies View RelatedCisco WAN :: Configuring WRVS4400N For AT&T DSL?
Sep 13, 2011configure my Cisco WRVS4400N wireless router for AT&T dsl.
View 0 Replies View RelatedCisco Firewall :: Configuring NAT In 8.3 Using DMZ 2
Sep 26, 2011We have a requirement where we need to enable a dynamic NAT from DMZ-1 to Inside, I gave the command below, but for some reason it does not work.nat (DMZ-2,Inside) source dynamic any interface,NOTE: The access-list is permitting all the traffic from DMZ-1 and Inside (for test)
View 1 Replies View RelatedCisco WAN :: Configuring WAN And LAN IP In ASA 5505?
Apr 8, 2012configuring the Cisco ASA 5505 device to access my both WAN and LAN ip. LAN ip i need to configure it for web servers to face the internet.
View 11 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.3 Configuring 802.1x
Jan 17, 2012Trying to configure 802.1x with ACS 5.3, have some general doubts about how to make it, this is what I got for the moment:
ACS 5.3 = 192.168.240.28
AD = 192.168.251.97
Switch = 192.168.240.171
IOS device config Already configured and running Device Administration using Tacacs, mising with Radius aaa commands:
aaa group server tacacs+ TACACS_PLUS
server 192.168.240.28
!
aaa group server radius RADIUS_1x
[Code]......
Cisco 5508 WLC - Configuring DNS
Aug 22, 2011Does anyone know if it is possible to use an 5508 WLC running version 7.0.116.0 as a DNS box? Was not able to find anything in the config guide.
View 2 Replies View RelatedCisco WAN :: Configuring BGP With 2811
Nov 2, 2011I have BGP router 2811. Want to configure BGP on it with two ISPs. How can i configure it?
View 1 Replies View RelatedCisco :: Configuring GLBP On Router?
Mar 30, 2012We have 7200 router on which two links from different ISPs are terminated. Right now one link is primary and the second one is redundant.Now we have procured our own IPs and plan to run BGP with both the service provider. Can we configure GLBP on the router so that both the links can be simultaneously used and when one goes down the other takes the full load.
View 2 Replies View RelatedCisco :: Configuring 2960 For VoIP?
Mar 26, 2012We just purchased cisco 2960 for our VoIP needs and we are using polycom phones, and Phone and Computer will use same port. Since Polycom phones are capable working with CDP protocol and we are hoping to get another switch to expand VoIP network. I found easiest way of setting up each port is as following (from the cisco tutorial)
Switch#configure terminal
Switch(config)#mls qos
Switch(config)#interface fastethernet 0/1
Switch(config-if)#mls qos trust cos
Switch(config-if)#switchport voice vlan dot1p
Switch(config-if)#switchport voice vlan 10
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 20
Switch(config-if)#exit
My first question,when we are using switchport voice vlan dot1p ,I thought we instruct the switch port to use 802.1P priority tagging for voice traffic and to use the default native VLAN (VLAN 0) to carry all traffic.Do I still need to create a Vlan 20 for data and Vlan 10 for voice ?
Secondly,same tutorial adds these commands as well,Do you think for our set up, using those commands are feasible ?
Switch(config-if)#switchport priority extend trust
Switch(config-if)#priority-queue out
Switch(config-if)#spanning-tree portfast
Switch(config-if)#spanning-tree bpduguard enable
Switch(config-if)#exit
Thirdly,when we get another switch and do the same configuration for the second switch, can I use any port on Switch 1 as uplink without doing any configuration ?
Cisco :: Configuring Static Routing
Jul 30, 2012Configuring static routing, how can i get a ping to go through a diff. route depending which host pinged? I want to ping host B from host A. Host A is connected to router1, which is connected to 2 other routers, router2 and router3. On the other end, routers 2 & 3 meet router4. Like a diamond topology. So basically routers 2 & 3 lead to the same place, router4, which is connected to host B. I need to configure static routing so that when I ping host B from A, both ping request and ping reply go through router1, 2, 4, host B, and back. THEN the part I dont understand, doing it the other way around: When I ping host A from host B, how can I get both ping request and ping reply to go through router4, THEN THROUGH ROUTER 3, then router1, then A, and back again to host B?
View 3 Replies View RelatedCisco :: Configuring RADIUS Server For It?
Jan 25, 2012Does anyone have or know of a tried and true method of configuring a Windows Server 2008 box to provide authentication/accounting services for Cisco devices. I've read a few websites already and a lot of them seem to be geared toward VPN and some of the settings each site goes through are different.I've got NPS installed and a RADIUS client configured with the shared key. Right now I'm in the process of creating the Network Policy which only allows a Windows "admin" group to log in. Curious about the "Constraints" section where the NAS Port Type is selected and the "Settings" section where the service-type and vendor specific options are configured.
View 18 Replies View RelatedCisco :: Configuring All MEC Links On 6500 VSS
Jul 13, 2012I will be configuring all the MEC links on my 6500 VSS chassis tomorrow morning and one thing I am a bit confused about.According to the best practices guide they suggest you configure all etherchannels trunks to be in desirable mode. All the trunks are using LACP active - active right now but that's only to one chassis.Should I change all my MEC etherchannel trunks to desirable mode or just leave them active-active?
View 6 Replies View RelatedCisco :: Configuring ACLs For HSRP
Feb 13, 2013I'm screwing around with HSRP running between two L3 interfaces of routers. I placed an inbound and outbound ACL on the same interface on both of these routers specifying to "permit ip any host 224.0.0.2" Why am I only seeing counters ticking for the inbound ACL of both of these routers? Is it an order of operations thing?
View 3 Replies View RelatedConfiguring Cisco Aironet 3500?
Jan 5, 2013We are planning to implement Aironet 3500, Do we need to have controller to install it or can we install as standlone AP.
View 1 Replies View RelatedCisco WAN :: Configuring 861 NAT With Multiple Public IPs
Jan 20, 2012I've replaced my dead ASA5505 with a 861-K9.Our ISP provides a subnet of public address /29 (wan side) by example: 200.200.200.xxx /29,we have 3 servers (lan side) in the example 10.1.1.xxx /24 is the same case than Johnatan, the only difference are the public addresses. [URL], everything is ok when NAT via the FE4 public address, but when do the same with other public IPs doesn't work.
View 7 Replies View RelatedCisco Application :: Configuring IP SLA On 2900?
Jan 9, 2013I am having two sites, at one site the ISP is terminated on 2900 Router and at one site ISP is terminated on 3500 L3 Switch. Now need to configure the IP SLA on this. In the current setup I am having two 2900 routers at one location and 3500 L3 switches which by point to point link.
View 1 Replies View RelatedCisco VPN :: Configuring In 1721 Router?
Nov 19, 2012configuring VPN in my cisco 1721 router to connect in vpn client
I have the public IPs.
Cisco WAN :: Configuring EoMPLS In 7600?
Mar 20, 2012You can configure EoMPLS on a port of the WS-X6724SFP card found in a Cisco 7600 with Supervisor 720.
View 1 Replies View RelatedCisco WAN :: Configuring ASA5510 With 2811 ISR
May 26, 2012I have a 2811 ISR configured to provide the following services to my network: Internet access to LAN usersCisco Call Manager ExpressSite-to-stie VPN to 3rd party networksVPN server to provide VPN access to remote usersSecurity Zone configurationsStatic NAT configurations.Now I recently just got the ASA5510 device and I am not sure how to go about with the setup, whether to put the ASA in between the internet and the ISR (Internet - ASA - ISR - LAN), or put the ISR in between the internet and the ASA (Internet - ISR - ASA - LAN)? While i know I can move most of the config unto the ASA, i know that the CME cannot be moved, hence I would like to do the setup such that users on the network still have access to CME.
View 2 Replies View RelatedCisco VPN :: Configuring Anyconnect On ASA5510?
Dec 22, 2011I have a small issue with the AnyConnect client. Under Windows XP, I was able to accept and install the certificate from the firewall and get a vpn connection working. But under Windows 7, I have to accept the certificate everytime I conect. Is there a reason for that?
View 3 Replies View RelatedCisco VPN :: Configuring Anyconnect On A ASA5510
Feb 24, 2011I have a small issue with the AnyConnect client. Under Windows XP, I was able to accept and install the certificate from the firewall and get a vpn connection working. But under Windows 7, I have to accept the certificate everytime I conect. Is there a reason for that?
View 2 Replies View RelatedCisco WAN :: Configuring The 2600 New Router?
Mar 4, 2012i want to configure the router for internet access for hosts this is the my pub ip x.x.x.174 and mask 255.255.255.252 this is isp given subnetmask internal ip range is x.x.x.20-x.x.x.254
View 1 Replies View RelatedCisco Switches :: Configuring SG-300 28 From Both Web And CLI Interfaces?
Dec 8, 2012I have been configuring the SG-300 28 from both web and cli interfaces.When doing a sh run I get Int gi2 before int Gi1? WTF?Also one of my vlans wasn't working on interfaces but was working through the assigned trunk port to my other switch.I deleted it and recreated it and it is now working. Why we have a failure and go to reconfigure a switch and have these same issues.
View 1 Replies View RelatedCisco AAA/Identity/Nac :: Configuring 802.1x With ACS 4.2 (RADIUS)?
Mar 25, 2013I am trying to configure AAA authentication and authorization with Cisco 3725 (IOS 12.4(17)) for 802.1x and ACS 4.2 with VLAN assignment to my Windows XP client. (trying to assign VLAN 100 in my scenario).When user connects to the Router, it passes the authentication process (EAP-MD5). In my debug i see that Router recieves the Radius Attributes BUT does not apply anything!My running config:
Building configuration...
Current configuration : 1736 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[code]......
As a result the vlan-switch data based does not change.
Cisco WAN :: Configuring 851 With PPPoE And DHCP
Aug 29, 2011Trying to find a way to configure my 851 for home use. My internet provider use PPPoE with PAP and althrough I found many configuration options they all are incomplete...or i cant find the logic behind those commands. First of all I need to say what I need:
1. Configurate my int Fa4 (WAN) with pppoe so when i insert my ISP cable in it it will negotiate and take IP.
2. Configurate DHCP on LAN (Fa0-3) so that when I insert my PC it will take a fake IP.
Here is the place where i found some conf examples: [URL] and I have some questions:
1. MTU - Should I use the 1492 value or the "pppoe-client ppp-max-payload 1500"?
2. ip route 10.10.25.2 255.255.255.255 dialer 0 - How can i set an IP route when my connexion informations only come after i connect? (Because is PPPoE)?
3. I cant configurate the DHCP because I dont know the default route, I dont know the DNS, and i dont know the default gateway because I dont know them due to PPPoE !
Cisco Infrastructure :: Configuring BGP On WS-3750G-12S-E?
Mar 24, 2013I have WS-3750G-12S-E with me and would like to configure BGP on the same. whether it is advisable to configure BGP on 3750G or not.
View 10 Replies View RelatedCisco WAN :: Configuring Two VLANs On 871 Router
Apr 23, 2013I use the cisco 871 router as a firewall to my home-office. I have configured two vlans for each seperate port. That is, FE0 configured as VLAN 10 ----> connected to Layer 2 Switch, FE1 configured as VLAN 20 ----> connected to another Cisco Layer 2 Switch,FE2 not in use, FE3 not in use and FE4 is connected to WAN.I got 100Mbps speed from the ISP, but I can see that I only get 50mbps even connected to VLAN 10 or VLAN 20.Does configuring two VLANs on Cisco 871 router divides the bandwidth (to Internet) into half?
View 35 Replies View RelatedCisco WAN :: Configuring Remote Access On 881?
Dec 10, 2012I'm configuring remote access on my cisco 881. Protocol PPTP was chosen.I've configured PPTP VPN access on my router, but there's an issue with accessing my LAN. I can access my Internet connection and open web sites, but I'm not able to access my local resources.I can only Ping my router's interfaces (192.168.2.10, 79.104.14.62) and Internet resources. For example, I can not ping switch, directly attached to the router, with address of 192.168.2.2 and other hosts on LAN.
View 1 Replies View RelatedCisco :: Configuring E-mail Notification In LMS 4.0
Nov 21, 2011I want to configure E-mail fault notification in LMS 4.0. So Where i will configure E-mail settings like username, password, mail server IP address in LMS. We are using e-mail service hosted in gmail. Through this mail service ca we able to use email notification.?
View 3 Replies View RelatedCisco WAN :: Configuring Two T-1s On VWIC2-2MFT-T1/E1
Aug 7, 2011I'm going to be swapping out a WIC-1DSU-T1-V2 for a new VWIC2-2MFT-T1/E1, going from one to two T-1s. This is on a 2800 router running 12.4(23)
configuration examples for the two T-1 setup ?
commands to verify the installation (show me the two T-1s are successfully bonded and communicating as one logical entity) ?
Cisco Wireless :: Configuring WDS With 1242 APs
Dec 26, 2011I'm using two cisco 1242 AG access points to configure WDS feature. I've named the accesspoints as AP1(acts as WDS) and AP2. Since I've only two accesspoints, I've configured the AP1 to act both as a WDS and as a regular accesspoints.Further I'm using the local radius server within the AP1 to authenticate both clients and infrastructure accesspoints. And both APs are connected to a router (which act as a dhcp server) via a unmanageble switch and both accesspoints are getting registered with WDS.But the issue is when I tried to connect to the configured SSID, it promts me a "authentication window" but after entering the configured username and password, i'm not getting authenticated by the AP.
I've attached the configurations of both APs to for your reference and I've used the following cisco document as a guideline to crate the WDS. [code]