I would like to know if I have only using IKEV2 to connect site to site VPN with Cisco 5505 device to connect few site. Which encryption method is better to choose with faster and stable IPsec encryption proposal,AES256, AES192, AES, 3DES, DES ?? which one is the best in IKEV2 site to site VPN tunnel?
View 4 Replies
I need to check and possibly change which Network address is allowed down a tunnel and check our Phase 2 IPSEC proposal. How would I do this on a VPN3000?
View 3 Replies View Relatedhow IPSEC VPN works but i hit a stumbling block understanding symmetric encryption keys.Here is my understanding about the process
1.Peers will negotiate plocies
2.Authenticate using pre-shared or certificates
3.Exchange DH Public Keys
4.Using Public keys encrypt symmetric key and exchange the same key which will be useful for communication
5.maintain sessions
But when we are configuring we will define encryption keys in isakmp phase and ipsec transform set ,i thought we will use the same encryption key for both management and data communication in fact i thought management phase is to give us a securely exchanged encryption key for the data tunnel.But we can use 2 different encryption keys in 2 phase i am bit confused.
I have 2 Cisco 2811 routers that are installed in different locations. I set up a tunnel connection between the two routers.
[code]...
To configure the GRE tunnel over IPSEC with OSFT via Encryption module from Cisco Router 3845, I have few queries:
1. Does the router 3845 support hot swap for encryption module?
2. Does the router require to be rebooted after plug in encryption module?
3. Any samples configuration for GRE tunnel over IPSEC?
How to reconcile what I've observed on our routers on a tunnel interface. The maximum amount of data I can get across the tunnel is 1339 bytes, which seems just a little bit too small. Background: we have two 3845 routers with IOS 12.4(3a) advanced ip services. I have tunnel interfaces on both routers, interface configs are below.
crypto ipsec transform-set MY_TSET esp-3des esp-sha-hmac comp-lzs crypto ipsec profile MY_VTIset transform-set MY_TSET
[ Code]..
When I test the mtu of the source destination interfaces I get 1500 bytes, as you would expect from an Ethernet connection to a service providers MPLS network. See output below:
Router1#ping ip 10.252.0.18 df-bit size 1500
[Code]...
When I test the mtu of the tunnels I get 1339 bytes, see the output below.
router1#ping ip 10.1.40.133 df-bit size 1340
Type escape sequence to abort.Sending 5, 1340-byte ICMP Echos to 10.1.40.133, timeout is 2 seconds:Packet sent with the DF bit setM.M.MSuccess rate is 0 percent (0/5)
[Code]...
That comes to a total of 1420, which is 80 bytes short of the mtu of the source/destination interface of the tunnel.
I've been troubleshooting this issue and was hoping to get some more feed back and maybe point out an error if I'm not seeing it. I recently setup a remote access VPN on Cisco ASA 5505. Everything appeared to work at first and the IPsec client connect. However if you look at the packets being encrypted an decrypted on the Client side only the encrypted counter is incrementing and the decrypted stays at 0. The opposite is true on the ASA side the decrypted continures to increment and the encrypted stays at zero. My first thought was maybe a mis configured NAT 0 statement or not defining the correct Split tunnel ACL but I have verified that. The asa version 8.2(5), I'll also list a packet-tracer I did from an inside host to VPN IP. [code]
View 1 Replies View RelatedWe have a situation where we need to encrypt the traffic on a Layer 2 V LAN. We have a Cisco Switch on each side but the fiber it runs over is leased and encryption (AES256 minimum) is required on a leased line. We have 2 ASA5505s that we could use on each side. Not sure what would be the best setup for this scenario (Site to Site). Or is there something better than using 2 ASAs on each side?
View 14 Replies View RelatedIs it possible to remove the high encryption (k9) from an Asa and make it into k8 model?
View 1 Replies View RelatedWe have Cisco ASA 5505 and an internal user (behind NAT) needs to connect via VPN to an external company. I just cannot get this to work. I have enabled IPsec Pass Through from ASDM Configuration --> Firewall --> Service Policy Rules --> Edit Service Policy Rule --> Rule Actions --> tapped IPsec Pass Through I have tried to find some info from the log but all i get is this message: IP = [remote gateway ip] Invalid Packet Detected!"I cant find anything that is blocked from the log.
View 2 Replies View RelatedASA 5520 running 8.0.4
ASDM v.6.1
Need assistance understanding how in ASDM/Configuration/Site-to-Site VPN/Connection Profiles/ "Any Entry" I can specify that I only want to offer an IKE Proposal of pre-share-aes-256-sha?
The IKE Proposal field has a number of possible options including: pre-share-aes-256-md5, pre-share-3des-md5, pre-share-aes-256-sha, pre-share-aes-192-sha, pre-share-3des-md5, pre-share-aes-sha and pre-share-3des-sha.
I am able to pick a specific IPSec Proposal w/o issue but when I attempt to do the same for the IKE Proposal, and click OK the choice does not "stick" but rather returns to the entire list as defined above.
On an ASA 5505 with the proper licenses running version 8.3, which would you consider the more resource intensive for the ASA, IPSec VPN or an SSL VPN with a portal?
The connections through the firewall would be the same so I am curious how adding the different types of VPN will affect the CPU and overall ability of the ASA to function.
I am trying to replace a 1751 IPSec VPN that connects a single LAN behind the 1751 to ~45 remote networks behind a single peer. There are a small number of workstations (~50) and low throughput (< 1MBps) across this VPN, the biggest trouble is the number of remote networks needed.
I have tried to connect an ASA5505 Security Plus in place of the 1751 and am able to get Phase 1 and Phase 2 up, except I don't get all of my ipsec sa's and can only pass traffic to some of the remote networks. Does the 25 IPSec limit apply to multiple sa's one one peer, I've only ever seen it spoken of as a 25 peer limit?
I have setup a ASA and everything but ipsec seems to be working. I was able to use the clientless ssl but I need ipsec working. I'm at a loss. config is a little sloppy and i will be cleaning it up but would like to get this working first.
Cisco Systems VPN Client Version 5.0.07.0290
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
[Code].....
I have Cisco ASA 5505 and i want to create vpn remote access ...l
so i created and connected to the vpn ...my problem is to reach my Local connection of 192.168.1.0 /24 i put the WAN Connection in the FA0/0 and put my LOCAL AREA CONNECITON into FA0/1 .. so how i can route or translate my connection , and using cisco ASDM 6.1 in GUI ,,,
I am trying to configure a Cisco ASA 5505 for Remote Clients.I am using ASDM interface and used the startup and ipsec wizards for my configuration but im hitting a stumbling block.For the last 2 days i have tried a number of configuration changes in attempt to make this work but failed, so i have done a factory reset and gone through the wizards again, so i have a clean configuration. Currently i have a Static Public IP Address 81.137.x.x and i am using a Netgear ADSL router, which is forwarding VPN traffic (UDP 500) to 192.168.171.35 (the wan port on the ASA 5505).The Cisco ASA has a default address of 192.168.1.1 I am using Cisco Client 5.0.06.0160.I have configured the client to use Group Authentication with the same credentials as setup through the wizard and im using Transparent Tunneling IPSec over UDP.I have attached 2 documents running_config.txt - which is shows the current ASA configuration Log-View.txt - showing error messages displayed in the real-time log viewer when i try to connect from the remote client.Im not sure whether i need to do any additional configurations for my setup other than simply run the wizards.
View 3 Replies View RelatedI am trying to configure an IPSEC vpn on an ASA5505 I setup an SSL vpn and it works fine, I can browse to the https: address log in and connnect to servers However when I try to setup the ipsec client access vpn it will not connect and I am getting the errors below I used the wizard for the initial configuration Looks like the inital IKE is being blocked or dropped?
%ASA-7-710005: UDP request discarded from my external IP/35781 to external:ASA-external/500
%ASA-7-710005: UDP request discarded from my external IP/35781 to external:ASA-external/137
I´m getting a dynamic public IP from my provider and what I´m trying to do is to establish a remote vpn tunnnel using IPSec which I achieve but every time the sessions resets or the ASA 5505 resets I get a new public IP and I need to put the new IP on the remote client so I can establish the vpn... How can I establish an ipsec vpn using DNS? For this scenario the remote vpn client is a vpn phone but it could be for any vpn client.
Private IP Public IP Private IP
PBX ---- (LAN) ---- ASA 5505 ---( Internet ) --- Remote Site ( Router ) --- (LAN) -- VPN Phone
I have a site to site IPSec tunnel setup and operational but periodically the remote site goes down, because of a somewhat reliable internet connection. The only way to get the tunnel to re-establish is to go to the remote site and simply issue a ping from a workstation on the remote network. We were having this same issue with a Cisco PIX 506E but decided to upgrade the hardware and see if that resolve the issue. It ran for well over a year and our assumtions was that the issue was resolved. I was looking in the direction of the security-association lifetime but if we power cycle the unit, I would expect that it would kill the SA but even after power cycling, the VPN does not come up automatically.
View 1 Replies View RelatedGot some issues when setting up IPSEC/VPN on the asa 5505. I want to connect from the ipad with the built in IPSec client..Get errors when i run the debug crypto isakmp
View 1 Replies View RelatedI configured an IPSec VPN tunnel between two ASA 5505 firewalls. I would like to make sure that the IPSec tunnel (hence the security association) is permanent and do not drop due to idle condition.
View 2 Replies View RelatedI just made a VPN on my ASA 5505 at home, I can connect successfully to it, but I can't contact anything in the network, nothing respond to ping or to anything else (include the ASA inside IP).
View 3 Replies View RelatedI have two sites with identical asa 5505's and each has the dual wan/ISP links and are set for failover using sla monitor tracking. I would like to create a vpn between these two sites that stays active regardless of which ISP link is online. Do I simply make two crytpo map statements10 and a 20 inside each of the asa's to each of the other ASA's STATIC PUBLIC IP's? [code]
View 6 Replies View RelatedI have a Site to Site IPSEC VPN Tunnel created with ASDM wizard.
Cisco ASA-5505
Peer A: x.x.x.x
Lan A: 192.168.0.0 255.255.255.0
Fortinet FortiGate-50b
Peer B: y.y.y.y
Lan B: 192.168.23.0 255.255.255.0
I start traffic from LAN B with a ping (or telnet it doesn't matter) that receive no reply but tunnel goes up fine.
"show isakmp sa" seems ok (says "State : MM_ACTIVE")
"show ipsec sa" seems ok but all #pkts are zero
try ftp, telnet from LAN B to LAN A systems but no one work. "show ipsec sa" all #pkts are zero As soon as I generate traffic from LAN A to LAN B these works (with tunnel already up) also traffic from LAN B to LAN A works.Obviously if I end VPN and start tunnel making traffic from LAN A all work fine bidirectionally, LAN A reach LAN B and LAN B reach LAN A.No msg logged in either two appliance.
Seems a very strange problem because seems not related to Phase1 or Phase2 already established.Traffic (routing ?) start works only after at least one packet goes from LAN A to LAN B.No msg logged in either two appliance.Problems begun in ASA version 8.0(4) ASDM version 6.1(3) and remain/continue after upgrade to ASA Version 8.4(1) ASDM version 6.4(1).
I'm trying to connect two ASA 5505s for a IPSec L2L VPN. They can connect, but not pass traffic from the AnyConnect subnet. I've added the config from ASA-2, with the LAN subnet of 192.168.138.0 and a subnet of 192.168.238.0 for AnyConnect client.
I'm trying to get the AnyConnect Clients access to the 192.168.137.0 LAN behind ASA-1 at 1.1.1.1. Having both 192.168.238.0 and 192.168.138.0 both access 192.168.137.0 is acceptable.
There's probably a lot of cruft in this config, as I've been reading all over forums and docs without much success.
:
ASA Version 8.2(1)
!
hostname asa-wal
names
name 192.168.238.0 anyconnect-vpn
!
interface Vlan1
nameif inside
[code]....
Having a problem getting an ipsec tunnel to work between 2 asa 5505. This in one of the two configs.
Result of the command: "show run"
: Saved:ASA Version 8.3(2) !hostname 20Pullmandomain-name skeincenable password IKxxneNMTRgDw/Xd encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 172.16.1.70 255.255.255.0 !interface Vlan2nameif outsidesecurity-level 0ip [Code]...
A customer has a 5505. According to the datasheet the limit of IPSEC sessions is 25 and the limit of anyconnect sessions is 25. Does that mean I can have 25 IPSEC tunnels and 25 Anyconnect tunnels at the same time? The customer needs at least 50 concurrent tunnels on his ASA. Am I understanding it correctly?
I was thinking the customer could pay for the anyconnect essentials license and connect his anyconnect clients to the ASA. Is that a good option to get the 50 concurrent clients connected?
I'm having trouble setting up a second IPSec VPN tunnel on my Cisco ASA 5505 to another office. I was able to setup the first one with no problem through the ASDM, but have not been able to get the second one up.The IPSec tunnel is connecting to a WRVS4400N router at the other office. I tried debugging crypto isakmp, and crypto ipsec, but I'm getting nothing. Below is the config. Does something look wrong on my end? I also attached a screenshot of the parameters setup on the remote router.
View 7 Replies View RelatedGot some issues when setting up IPSEC/VPN on the asa 5505. I want to connect from the ipad with the built in IPSec client..Get these errors when i run the debug crypto isakmp.
View 6 Replies View RelatedI have 2 ipsec tunnel active on ASA5505 (secplus license).I would like to activate sslvpn also. Is it possible or there are issues in keeping active both services?
View 3 Replies View RelatedI have difficulties with configuring Remote IPSec VPN with Cisco ASA 5505 and Windows 7 native VPN client. My client PC gets VPN pool IP address, and can access remote network behind ASA, but then I lose my internet connectivity. I have read that this should be an issue with split tunneling, but I did as it is told here and no luck.On Windows VPN Client settings, if I uncheck "use default gateway on remote network" I have internet connectivity (since client is using local gateway), but then, I cannot ping remote network.In log, I see this warnings of this type:Teardown TCP connection 256 for outside:192.168.150.1/49562 to outside:213.199.181.90/80 duration 0:00:00 bytes 0 Flow is a loopback (cisco)I have attached my configuration file (without split-tunneling configuration I tried). If you need additional logs I'll send them right away.
View 4 Replies View RelatedWe currently have 2 different ASA 5505 connect to our ASA5510. We want to VPN connect the 2 5505's to each other while still mantaining connection to our 5520. I have attached pdf of what we have. What we want is to connect traffic between the two 5505's so that devices in either location can talk to each other while still mantainig connection to the 5510.
View 13 Replies View RelatedI want to configurate cisco ipsec vpn client at asa 5505. At my asa the software version is 8.4. Any link or some material to config ipsec vpn client at asa 5505 version 8.4.
View 1 Replies View Related
