I have seen that the current WLC software release, 7.0.116.0, does not support secure LDAP using TLS. Are there any plans to incorporate this feature? (I've read that it was supported in previous releases to version 4.2). Is it in the roadmap of the product?
View 1 Replies
I am setting up an LDAP identity store over ldaps in ACS 5.1. I specify that the connection uses secure authentication and provide the Root CA certificate. When I hit "Test Bind to Server", I get this error message in a popup window: "Connection test bind Failed :server certificate not found"Is this saying that ACS can't find the CA certificate uploaded, or does it mean the actual certificate presented by my LDAPS server during the bind test?
View 2 Replies View RelatedI am working on project with Secure ACS 5.2. I am trying to determine the proper External Database to use. LDAP or direct to AD?
Additionally, the Domain that I am connecting to has Multiple sub domains. All of the users are currently in the Sub domains, but will be moving to root domain later. How should I configure the connection, do I need to connec to each sub domain or can I just connect to the root?
I'm trying to configure an ASA to communicate with an AD environment that is only using LDAP Secure (LDAPS). I've configured authentication to ASA's with LDAP lots of times, though never with LDAPS.
Presumably there is a procedure to install a certificate in the same way as an RSA sig in VPN.
After trying for several hours to configure ldap attribute to cisco attribute mapping, I found that special characters are not supported by ldap attribute-map at least on 8.4
Here is the problematic configuration:
ldap attribute-map ldap_memberof_map
map-name memberOf Group-Policy
map-value memberOf
[Code].....
I have two WLC5508 controllers configured with multiple SSIDs and a VLAN associated to each of them. Now I am deploying a pilot for Web-Authentication and everything seems to be fine except for the LDAP authentication part. I have done all the steps for enabling anonymous bind on Active Directory (AD) and the configuration on the controller is properly in place. I know the configuration is working fine because I have isolated the problem to some sort of routing or communication problem:
Controller Interfaces:
Management Interface - Vlan 1, (X.X.148.99)
Student Interface - Vlan 2 (X.X.132.99)
Mobile Devices interface - Vlan 28
Web authentication interface - Vlan 31
AD is on Vlan 2 (Student Interface range)Each interface has its own IP in a different IP range.
If there is an IP address configured on the Vlan2 interface, LDAP wont work. If there isnt an IP address on the Vlan 2 Interface LDAP works!So you may think I just should not configure an IP for that particular Vlan, but if do this, the controller wont allow to associate any WLAN to that particular Vlan interface and unfortunately I am using it.
I think the Controller uses the Management interface to send traffic to the LDAP server and it gets confused of getting a reply from a device which belongs to the Vlan 2 Interface IP range (AD is on Vlan 2).
I know the controller is a Layer 2 device, so I am not sure why it should need an IP address to be configured for each interface, I read it is used just for roaming purposes but it seems to be somehow related to LDAP communication process as well.
The strange thing is that I can access the management interface IP from the Vlan 2 range and there is not problem at all.
PD: Controller 5508, Software version: 7.0.230.0
We are using WLC-5508 in our corporate. For authenication we have implemented ACS with LDAP configured as external user database. We can able to get authenicated for Web based authenication. When it is configured for EAP-FAST, authenitication is not happening.
View 3 Replies View RelatedFrom what I've read, it doesn't seem possible to use Web Authentication and obtain encryption unless using a Radius server.
I have a client asking for web auth, encryption, and ldap connection to their AD servers.
I'm having a problem with a WLC 5508 and a LDAP on windows server 2008, I already config everything on the WLC, but when a user try to authenticate I have this debug result:
*aaaQueueReader: Jul 15 19:27:07.384: 00:1b:77:7b:19:aa Returning AAA Error 'No Server' (-7) for mobile 00:1b:77:7b:19:aa
*aaaQueueReader: Jul 15 19:27:07.385: AuthorizationResponse: 0x3c9ceac4
*aaaQueueReader: Jul 15 19:27:07.385: structureSize................................32
*aaaQueueReader: Jul 15 19:27:07.385: resultCode...................................-7
[code]....
I am having problems with my WLC to connect in my LDAP (ActiveDirectory). I have 3 interfaces in the controller:
- Management (vlan709): 10.41.200.253
- lan (vlan 1): 190.1.1.123
- guest (vlan 708): 10.41.222.253
My LDAP server is: 190.1.1.22
The controller could ping the LDAP Server. And LDAP Server ping WLC too. When the controller try to connect in the LDAP server, return this on debug:
ldap_db.c:1038 Could not connect to LDAP server 1, reason: 1005 (LDAP bind failed).
*LDAP DB Task 1: Oct 29 15:11:16.924: %AAA-3-LDAP_CONNECT_SERVER_FAILED:
*LDAP DB Task 1: Oct 29 15:10:52.932: ldapInitAndBind [1] called lcapi_init (rc = 0 - Success)
*LDAP DB Task 1: Oct 29 15:10:54.932: ldapInitAndBind [1] configured Method Authenticated lcapi_bind (rc = 1005 - LDAP bind failed)
*LDAP DB Task 1: Oct 29 15:10:54.932: ldapClose [1] called lcapi_close (rc = 0 - Success)
*LDAP DB Task 1: Oct 29 15:10:54.933: LDAP server 1 changed state to IDLE
*LDAP DB Task 1: Oct 29 15:10:54.933: LDAP server 1 changed state to RETRY
*LDAP DB Task 1: Oct 29 15:10:54.933: LDAP_OPT_REFERRALS = -1
I am deploying Redundant WLC 5508 with 4 VLANs and 4 SSIDs Match to it, Everything works Fine, now i need to do the below:
1. I need All Wireless Users need to authenticated with Existing Active Directory/LDAP
2. I will Create Guest Accounts in my AD , and pass to Guests, Then Guest should only Access Internet except Corporate Resources
2. How can i secure my Voice VLAN for Wireless Phones. I want only WIreless Phones to Connect to Voice VLAN.No internet Access on Voice VLan
We have 5508 controller (redundant) & would like to configure Staff vlan to get authenticate with active directory.i am new to the controller device & want to configure controller with active directory (windows 2012).
5508 controller (Active & Standby) with 48 Access Point.(configuration Done) Guest Vlan (only for internet Access) controller based web authentication configured.
Staff Vlan ( inside & outside ). Need to configure with LDAP authentication?
I using IOS c2950-i6k2l2q4-mz.121-22.EA14.bin but no support command "ip http secure-server" and I not connect switch by CNA. How I fix ? Or IOS C2950 support ip http secure-server and ssh ver2 ?
View 1 Replies View RelatedHow many newtork devices can Cisco Secure ACSv4.1 support is there any limit on the same? How to get the Specs of Cisco Secure ACSv4.1 on the above grounds...
View 2 Replies View RelatedI am running into an issue with disabling the web-auth secure web on an 5508 anchor WLC running 7.2.110. After the WLC rebooted, the guest authentication portal didn't show up...I could see the IE tab showed Web Auth Redirect though...Changed again the web-auth secure web to enable and rebooted the WLC fixed the issue.
View 4 Replies View RelatedI have a requirement to set up a guest SSID for contractor so that they can use the internet while in the office.
Security say that all traffic on this SSID should be isolated and directed straight to the firewall, with no chance of contamination into the company network infrastructure.
With the 5508, my understanding is using the setting up a guest account functionality built in will achieve this, but all traffic would end up at the wireless controller. How do I then put a direct forward for all traffic to the firewall which will only affect the guest traffic?
I got a problem when I use WLC 5508 connect to LDAP for authentication, but no luck there, it's a simple config, but not easy to work on my job, I got the following messgae. [code]
View 9 Replies View RelatedAs we know that WLC (i.e. 5508) does not support MAB (MAC Auth Bypass) and it supports CWA in 7.2.x. CWA is a result of successfull MAB. So how CWA work for wireless? So it means WLC support MAB?
View 5 Replies View RelatedI have a new deployment of 44 3502i AP's in 3 buildings at one of my campus'.The 5508 wlc is running latest 7.0.116.0 code.I have some users who take their work with them as they go from location to location on this campus.They need to be able to smoothly switch from AP to AP without having to reauthenticate each time the next AP takes over in the handoff.On the ssid in question we run 802.1x back to 1 auth server; there is no failover auth server.All APs are in one AP Group.My thought is to add all 44 of the APs to one HREAP Group.
View 4 Replies View RelatedWe are moving forward with a mobility project which requires our network to authenticate/authorize based on certificates.
WLAN_1 has 802.1x enabled passing the cert through to the MS CA which authorizes the cred, which in turn passes the AD creds of the user to the MS RADIUS server for authenticate/authorization.
Hardware: WLC 5508 running 7.2.110.0 3600 APs ACS 5.2 not used for AAA
1. As we turn up additional SSIDs, we need Mobile SSID to accept ONLY the Mobile Cert, our Internet SSID to only accept the Internal Cert and our GUEST SSID to deny ANY Cert issued by our CA.I know ISE makes this much easier, but I dont have it and need this to work as best we can until next fiscal cycle..
How Cisco Identity Service Engine (ISE) can work with WLAN controller 5508 to do the Local Web Authentication, on behalf tje guest profile is create using Cisco ISE guest management?
As i check Cisco ISE caveat wireless only support on LWA, and LWA not supported on Authorization's VLAN assignment.
what i need to concern abou the ISE authentication and authorization policy on behalf on Wireless LWA with use of ISE guest management case?
I'm running version 7.2.111.3 on my WLC 5508 and I try to figure out how I can set PEAP towards my configurerd Radius servers. On my Local EAP profile I can specify PEAP, but how is it default configurerd when you just specify the radius servers on the "WLANs > Edit Test > security > AAA servers tab ?
The MS radius logs tell me that it is EAP and not PEAP, so the questions is does the WLC support Microsoft: Protected EAP ???
Dot1x_NW_MsgTask_0: Oct 10 11:02:27.279: 24:77:03:07:75:28 AAA EAP Packet created request = 0x1bd4647c.. !!!! -> should be AAA PEAP ?
*Dot1x_NW_MsgTask_0: Oct 10 11:02:27.279: 24:77:03:07:75:28 Sending EAP Attribute (code=2, length=35, id=2) for mobile 24:77:03:07:75:28*Dot1x_NW_MsgTask_0: Oct 10 11:02:27.280: 24:77:03:07:75:28 [BE-req] Radius EAP/Local WLAN 3.
I have a customert that needs to support 200 laptops over 16 classrooms with scalability to 400 laptops. I have a heatmap design to cover this with 22 1042 access points. Does any one know what features the 5508 has over the 2504? By reviewing the data sheets, the biggest feature difference is better support for mobility, which not a need for this deployment as they just wheel a cart of laptops into a classroom and fire them up. Also, does the 2504 support LAG across the four gig interfaces?
View 1 Replies View Relatedis there a support of 1+1 mode (HA mode) at 5508 Controller? If yes Is there a HA bundle or do we have to order two identical 5508 controller ?
View 6 Replies View RelatedI am trying to follow the Fips guide for the WLC5508 and it wants to encrypt the connection to the Radius, either with PSK key wrap or IPsec. I have the options for Ipsec only as the Windoes NPS does not support Key wrap from what a previous user confirmed for me here on the board.. But then found another post that states that the 5508 does not support IPsec?
View 5 Replies View RelatedWhen setting up my e1000 router for a secure domain it automatically opened a non secure one that my neighbors are using. How can I cancel it?
View 2 Replies View Relatedi am facing an issue while trying to configure LDAP integration on Cisco ASA firewall. The requirement is allow the remote access VPN to specific group defined on AD. When i checked the debug logs " debug ldap 255" , it shows that the authenication is sucessfull with the LDAP server , but the ldap attribute is not getting mapped and because of this reason , the tunnel-group default group policy of "NOACCESS" is getting applied ( vpn simultanous set to zero) that results zero connection.
I confirmed this by changing the value of NOACCESS from zero to one and found that the VPN is getting connected
The name of user account is testvendor that belongs to the group of Test-vendor.
The configuration and debug output is shown below.
SHOW RUN
ldap attribute-map ABC-VENDOR
map-name memberOf Group-Policy
[Code]....
Is it possible to encrypt password provided for the ldap-login-password attribute in the ASA configuration? Our auditor is not comfortable with the LDAP (AD) password appearing in clear text in the configuration
View 6 Replies View Relatedi am trying to get ad authentication working on a WLC 2504, can I use the LDAP server configuration for authentication?
View 1 Replies View RelatedI have cisco ASA 5505 with security plus, i configured remote VPN with ASA for LDAP authentication which works as i want. Now i have a requierment that some users needs to get access via remote VPN but they are not part OUR SERVER Active directory, Is that a possibility that users have an access of remote VPN while not creating an account in AD and perfrom local authentication via firewall for them?
View 1 Replies View RelatedI have some problems integrating WLC 4400 with AD using ldap. The the WLC LDAP Server and W LAN for Web Authentication are configured according to [URL].
when I connect to SSID the laptop is given the ip address, then I can see the web-page with lo gin and password - it seems to be OK, but when I enter lo gin and pass it tells me, that it's incorrect.
The attributes of the LDAP server:
Server Address *.*.*.*
Port Number 389
User Base DN ou=ORG,dc=domain,dc=local
User Attribute userPrincipalName
User Object Type Person
the test user is located in AD folder ORG, but this folder also contains a lot of sub trees
There are some questions:
1) Is it obligatory to use value "Authenticated" in the Simple Bind option or it can be Anonymous?
2) Is the Controller capable for searching the users located in User Base DN sub trees?
Here is some debug from the controller:
667: LDAP_CLIENT: UID Search (base=.....
669: LDAP_CLIENT: ldap_search_ext_s returns 0 85
669: LDAP_CLIENT: Returned 1 msgs including 0 references
[Code]....
I am planning to implement SSL-VPN (Any Connect) on an ASR 1002 router running IOS-XE Software Version 15.1(3)S2. I need to use LDAP for user authentication, and need to understand what are RADIUS/ TACACS requirements to use LDAP. Do I need to use Cisco ACS or can I use something like Microsoft IAS or Free Radius?
View 6 Replies View RelatedI'm trying to get my LMS 4.2.3 to do LDAP authentication up against our Windows 2008 R2 Domain.url...
As far as I can see It all has to do with LMS not being able to get a functional connection to the AD that allows for LDAP query's: [code] How does this LDAP thingie work? The documentation states that I must supply a specific user to the Usersroot, since I'm on a 2008 domain, but where do I provide the password for this account, so LMS can log in and do its LDAP queries?
