Is it possible to encrypt password provided for the ldap-login-password attribute in the ASA configuration? Our auditor is not comfortable with the LDAP (AD) password appearing in clear text in the configuration
View 6 Repliesi have following problem. I configured on a Cisco ASA5510 VPN authentication with LDAP. It works fine but one thing doesnt works.If i configure on my Active Directory the user for "User must change Password at next login" the message for password change is coming (look screenshot AnyConnect1), but if the user want to change his password, the password will not accepted by the system(look screenshot AnyConnect2).In the Group Policies on my Active Directory i disabled all features(look screenshot Pic1)I tried all combination for the password, but nothing will accepted.i configured LDAP over SSL and in the Tunnel Group i enabled the password management with "NOtify User 2 days prior to password expiration".
View 3 Replies View RelatedI've gotten to the point where I can test against active directory and get in, also I can get AD groups from my server on the ASA. My problem, I can't connect in via my AnyConnect client on my Android. I immediately get a "log in failed" and I know I'm using the right username/pass. Doing a little troubleshooting, I have attached my AnyConnect debug log and the results of the "debug ldap 255" command on the ASA. Also, I've used ldp.exe to determine I can connect in with the username/password combo I'm using.Combing through the AnyConnect logs I see a few instances of "global error unexpected" but no Google searches have brought up anything useful.
View 7 Replies View RelatedWe have 5508 controller (redundant) & would like to configure Staff vlan to get authenticate with active directory.i am new to the controller device & want to configure controller with active directory (windows 2012).
5508 controller (Active & Standby) with 48 Access Point.(configuration Done) Guest Vlan (only for internet Access) controller based web authentication configured.
Staff Vlan ( inside & outside ). Need to configure with LDAP authentication?
I setup a password for my router configuration. But i forgot it.
View 1 Replies View RelatedRecently, I purchased a Cisco 871W Router with which to practice/study for my CCENT with. Since I have made the purchase, it has given me nothing but headaches.
I cannot access the router to configure it, as the previous owner has a password set on it to access enable mode, which he/she has forgotten.
Here is the message that I receive when I attempt to log in into the router, to access enable mode. [URL]
Apparently there is supposed to be a one-time username and password of "Cisco", but this is not the case.
I have tried to do a password recovery, following this post discussion thread: [URL]
Unfortunately, this has not worked, and I am sure that I am doing something incorrectly. I am connected to the router via console cable and have tried power cycling the router and entering the break sequence, power cycling again, and then holding the space bar down for 15 seconds. The preceding has produced no results to speak of. Following, I set my terminal emulator, Tera Term, to the baud rate of 1200, power cycled the router, and held down the space bar for 20 seconds. I then immediately set the baud rate back to 9600. Nothing occurred, once again.
Furthermore, I have followed the password recovery instructions set forth by Cisco. [URL]
Nothing has come of these methods, either, and I do not see how they would work, or even apply to my situation, as Cisco seems to imply they should, as I cannot get into enable mode, let alone privileged mode or conf t mode, as the guidelines require.
Here is some info for troubleshooting:
OS: Win 7 HP 64 bit
Terminal Emulator: Tera Term
Router is not currently connected to any sort of internet connection. Only the power cord and console cable are properly connected.
I'm at my brother's house and I'm trying to connect to hs wireless network. I know the password but whenever I try to enter it it gives me a message that says, "The network password needs to be 128bits or 256 bits depending on your network configuration. This can be entered as 8 to 63 characters or 64 hexadecimal characters." From other forums I've looked at it says that I need to get to the router settings page. It gives me an IP adress to paste into the web browser but it doesn't come up as anything. What the heck?
View 4 Replies View RelatedI am setting up a guest WLAN network on our existing 1242 AP's using a seperate VLAN. On most wireless devices which are on the company network/VLAN's, I have used WEP authentication with hex keys, and no broadcast. Obviously this cannot be the same for a guest internet connection.We want to have the VLAN/SSID in guest mode (which i have configured) for broadcasting, and then once someone selects the SSID on their laptop or smart phone, they are just prompted to authenticate with a standard alphanumeric password (example "guestwifi") instead of a 40 or 128 bit key.
I have searched all over and tried multiple things in the CLI on AP1, but can't seem to get anywhere.
I am new with ASA devices I have a ASA 5505, the former IT manager does not remember the password of it. I am just wondering do I lose the configuration on it if I reset the password?if yes, how can I download the configuration before resetting the password. and how can I upload the downloaded configuration
View 2 Replies View RelatedI have a wireless setup with a linksys router hooked up. I mainly connect with my laptop but now I'm trying to test out a Dell Inspirion 3000 Windows XP. The Dell picks up the signal of my connection that is secure when I have the proxim router connected. When I go to put in my password I get this message : "The network password needs to be 40bits or 104bits depending on your network configuration. This can be entered as 5 or 13 ascii characters or 10 or 26 hexadecimal characters." Otherwise if I direction plug in the Ethernet cord it 'connects' but I can't do anything. I'm set up as a WPA Personal in security mode when I got into my linksys account.
View 2 Replies View RelatedRecently I came across a router (Cisco 3845, IOS 12.4) configured for TACACS, one local username and an enable password. Going through the configuration I noticed the router didn't have an enable secret password which I thought was strange. The TACACS config is below, comments regarding the TACACS config and the consequences of not having an enable secret or if there is a need for one.
aaa authentication login default group tacacs+ aaa authentication login no_tacacs enable aaa authorization exec default group tacacs+ aaa authorization commands 1 default group tacacs+ aaa authorization commands 15 default group tacacs+ aaa accounting exec default start-stop group tacacs+ aaa accounting commands 1 default start-stop group tacacs+ aaa accounting commands 15 default start-stop group tacacs+ aaa accounting network default start-stop group tacacs+
I'm moving from an 1801W to an SRP547.My adsl supplier (BT) has given me a username and password, and also a router IP address, a subnet and an gateway IP address. I have 13 fixed IP addresses. I don't speak cisco, so I'm using the built in interface to configure it.If i choose IPoA I can enter the IP settings. If I choose PPPoA I can enter the username and password.I do not see anyway I can enter both the IP settings and the username + password on the WAN configuration page.
View 9 Replies View RelatedRegion : Others
Model : TL-MR3420
Hardware Version : V2
Firmware Version : 2.1
ISP : PTCL
trying to connect to router configuration (after several factory resets) at 192.168.0.1 but each time screen displays invalid username / password,doesnot even display username / password window,using admin as username and password,just cannot log on to configuration setup
how to recover password and retrive configuration on Cisco switch 2950 and 3560.I know the way to press and hold the mode button and then plug in the power cord can reset the switch to factory default but it will reset everything to nothing. As such, it is not what I want and I want to keep the configuration file and able to use the configuration on the switch.
View 2 Replies View Relatedi am facing an issue while trying to configure LDAP integration on Cisco ASA firewall. The requirement is allow the remote access VPN to specific group defined on AD. When i checked the debug logs " debug ldap 255" , it shows that the authenication is sucessfull with the LDAP server , but the ldap attribute is not getting mapped and because of this reason , the tunnel-group default group policy of "NOACCESS" is getting applied ( vpn simultanous set to zero) that results zero connection.
I confirmed this by changing the value of NOACCESS from zero to one and found that the VPN is getting connected
The name of user account is testvendor that belongs to the group of Test-vendor.
The configuration and debug output is shown below.
SHOW RUN
ldap attribute-map ABC-VENDOR
map-name memberOf Group-Policy
[Code]....
i am trying to get ad authentication working on a WLC 2504, can I use the LDAP server configuration for authentication?
View 1 Replies View RelatedI have cisco ASA 5505 with security plus, i configured remote VPN with ASA for LDAP authentication which works as i want. Now i have a requierment that some users needs to get access via remote VPN but they are not part OUR SERVER Active directory, Is that a possibility that users have an access of remote VPN while not creating an account in AD and perfrom local authentication via firewall for them?
View 1 Replies View RelatedI have some problems integrating WLC 4400 with AD using ldap. The the WLC LDAP Server and W LAN for Web Authentication are configured according to [URL].
when I connect to SSID the laptop is given the ip address, then I can see the web-page with lo gin and password - it seems to be OK, but when I enter lo gin and pass it tells me, that it's incorrect.
The attributes of the LDAP server:
Server Address *.*.*.*
Port Number 389
User Base DN ou=ORG,dc=domain,dc=local
User Attribute userPrincipalName
User Object Type Person
the test user is located in AD folder ORG, but this folder also contains a lot of sub trees
There are some questions:
1) Is it obligatory to use value "Authenticated" in the Simple Bind option or it can be Anonymous?
2) Is the Controller capable for searching the users located in User Base DN sub trees?
Here is some debug from the controller:
667: LDAP_CLIENT: UID Search (base=.....
669: LDAP_CLIENT: ldap_search_ext_s returns 0 85
669: LDAP_CLIENT: Returned 1 msgs including 0 references
[Code]....
I am planning to implement SSL-VPN (Any Connect) on an ASR 1002 router running IOS-XE Software Version 15.1(3)S2. I need to use LDAP for user authentication, and need to understand what are RADIUS/ TACACS requirements to use LDAP. Do I need to use Cisco ACS or can I use something like Microsoft IAS or Free Radius?
View 6 Replies View RelatedI'm trying to get my LMS 4.2.3 to do LDAP authentication up against our Windows 2008 R2 Domain.url...
As far as I can see It all has to do with LMS not being able to get a functional connection to the AD that allows for LDAP query's: [code] How does this LDAP thingie work? The documentation states that I must supply a specific user to the Usersroot, since I'm on a 2008 domain, but where do I provide the password for this account, so LMS can log in and do its LDAP queries?
Is LDAP web authentication supported on the AIR-WLC2006-K9? There is a place to add LDAP servers in there but I can't seem to get the web authentication piece of it to work. I saw some idications on forum posts online that made me think that it wasn't supported but I never found a definitive cisco answer. I have it set up and working great on a 5508 wireless controller.
View 1 Replies View Relatedprovide me Step by Step procedure for integrating LDAP with ACS 5.2 .
View 1 Replies View RelatedI am having a problem getting an ASA running 8.3 to authenticate an SSL VPN directly against an LDAP on Windows Server 2003. I have changed the read access on the Active Directory to allow Annonymous to read it. I think I am missing something on the ASA config. I have the Server Group specified with the address of the correct server but nothing else really configured.
View 1 Replies View Relatedknow about Domino LDAP ? I would like to integrate this LDAP with Cisco ISE.I try to bind this LDAP but it does not show me anything in "Naming Context". So I cannot choose group to map into ISE.I test this on WLC. It is success to do but cannot make the same thing with Cisco ISE.Is this LDAP supports with Cisco ISE 1.1.1 ?
View 3 Replies View RelatedI have seen that the current WLC software release, 7.0.116.0, does not support secure LDAP using TLS. Are there any plans to incorporate this feature? (I've read that it was supported in previous releases to version 4.2). Is it in the roadmap of the product?
View 1 Replies View RelatedWe are attempting to use LDAP for web authentication on a WLC 4402.
[URL]
You are able to connect to the SSID and it reidrects you to the login page as it should. When you enter your username and password you get a message that "the username and password combination you have entered is invalid." Based on the following log it looks like the LDAP bind is the issue.
*LDAP DB Task 1: Dec 19 11:19:26.584: %AAA-3-LDAP_CONNECT_SERVER_FAILED: ldap_db.c:1038 Could not connect to LDAP server 1, reason: 1005 (LDAP bind failed).
We are able to test the following configuration with ldp.exe successfully,
Server: ***.***.***.***
Port Number: 389
Bind Username: CiscoBYOT
[Code].....
I have 2 SSIDs on WLCs.I would like to have 1 SSID point to the acs radius using LDAP store and the 2nd SSID point to the acs radius using the host identity store for mac filtering.both scenarios are working, but not together.if I adjust the rule order I can get one SSID, but then the other fails. [code] It seems to me that there should be a simple process to make this happens. I thought if the rule is not matched it would move on to the next rule etc.I might be able to live with first checking ldap and if that fails move on to the local host db, but that seems ineficient. url...
View 3 Replies View RelatedDoes loadbalancing ldap services in ACE? Both port 389 and 636.
View 4 Replies View RelatedI'm trying to setup WLC for LDAP to authenticate the users. I have all the components required according to cisco's document. WLC4402, LAP1142N, 2008 AD serving as LDAP.
I'm configuring according to the document and also trying same settings from other users on this forum who (seems to) have got the WLC-LDAP up and working. My problem is that I'm receiving the below debug message on the controller and there is nothing on the internet on this error:
*LDAP DB Task 1: Apr 28 10:05:35.903: LDAP server 1 changed state to IDLE*emWeb: Apr 28 10:09:21.046: aaaLdapServerStateSet [1] changed state to 'DISABLED'.*emWeb: Apr 28 10:09:21.046: aaaLdapServerStateSet [1] changed state to 'ENABLED'.*LDAP DB Task 1: Apr 28 10:09:21.052: ldapTask [1] received msg 'CLOSE' (4) in state 'IDLE' (1)*LDAP DB Task 1: Apr 28 10:09:21.055: ldapClose [1] called lcapi_close (rc = 1008 - Invalid client handle)*LDAP DB Task 1: Apr 28 10:09:21.055: LDAP server 1 changed state to IDLE
I'm getting this error regardless of the authentication type, any username and attributes. So it makes me think WLC is not even trying to bind to LDAP. If the error was invalid credentials or something mismatch or something, it gives me some information to base my troubelshooting but I just can't find information on this (rc = 1008 - Invalid client handle) message.
I need to integrate a 2504 WLC with a windows 2003 LDAP server for extented authentication, is there any guides available for this ?
View 1 Replies View RelatedWLC 4404 LDAP Bind Fails
View 12 Replies View RelatedI have an CS-ACS appliance with 5.2.0.0.26.3 version. There is not any direct solution for connect ldap client to server. I have 3 servers that have only ldap and for authentication I can not use radius or Tacacs+. I need a solution for this problem. How can LDAP Client connect to ACS when it has only ldap protocol?
View 1 Replies View RelatedPreviously, I was able to configure our Easy VPN Server with local authentication.But now, I am trying to use LDAP authentication to match with our policies.
My router is a Cisco1941/K9.
Current configuration : 5128 bytes!! Last configuration change at 13:25:16 UTC Tue Aug 28 2012 by admin! NVRAM config last updated at 05:03:14 UTC Mon Aug 27 2012 by admin! NVRAM config last updated at 05:03:14 UTC Mon Aug 27 2012 by adminversion 15.2service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Router!boot-start-markerboot-end-marker!!!aaa new-model!!aaa group server ldap ASIA-LDAPserver server1.domain.net!aaa authentication login ciscocp_vpn_xauth_ml_1 localaaa authentication login ASIA-LDAP-AUTHE group ldap group ASIA-LDAPaaa authorization network VPN_Cisco localaaa authorization network ASIA-LDAP-AUTHO group ldap group ASIA-LDAP!!!!!aaa session-id common!!no ipv6 cef!!!!!ip domain name domain.netip cef!multilink bundle-name authenticated!crypto pki token default removal timeout 0!crypto pki trustpoint
[code]....