confirm if the highest speed I can get over WiFi with WRT160N v3 is actually 270 Mbps (and not 300 Mbps as advertised), And there's one more thing - is it normal to have Signal: -51; Noise: -93, SNR: 43, Signal quality 53% if I am only 2 meters far from a router? TX power is set to 28.
I have a wrt160n v3. This is the 3rd one - both the first 2 were defective. I have spent approximately 8 hours troubleshooting the other 2 only to be told they're defective. So, I got a new one. Now, this one keeps cutting in and out. I want as my iPhone constantly switches from 3G to wifi on and over every minute. It really ticks me off! What can I do to fix this? This is a different issue than the original one (very slow) and 2nd (no signal). It's disappointing for a $90 router to do this. I also see the wireless icon on the router flash.
turning my wireless back on. Some how in attempting to create a shared file between my pc and my wife's Mac the wireless has been disabled. I have tried resetting the device several times following the instructions on line however I still can not get the wireless to re activate. I tried reverse directions from the posts on how to turn off the wireless but still no luck. I tried restoring the computer to a later date?
I'm having an issue getting my tv to start connecting again to the wireless router.Have tried pin setup (timed out & didn't connect...attempted at least 10 times in this fashion)Have tried entering the password (router seems to refuse the connection to the tv)About a month ago, I was in the Network Magic Map & it looked like one of the laptops had been cloned, so I removed it from the network.
I have a WRT160N v3 Linksys Router and it keeps disconnecting and then reconnecting. It only disconnects wirelessly. LAN still works fine.I have tried a lot of different methods to solve this issue, but none seem to work.I am very dissappointed in the quality of the product. It has done this every since it was bought. I personally would have sent it in for repairs, but others in my household would not have agreed to that.
Just tried to register my WRT160N V2 and when I tried firstly there is no option for the version 2 model and secondly it says my serial No is incorrect when I have tried it three times and have checked it thoroughly.
I have two PC's hardwired to this router that are working okay (although performance has been choppy lately). The past 4 days however, when I try to connect wirelessly I get connections that are repeatedly dropped. I am in the Settings section of my iPad 2 and it keeps rapidly switching between "connected" and "not connected". Firmware is up to date.
Desktop Xp 3 and connected printer, Comcast cable, WRT160N, wireless laptop w/ Xp 3. Printer is only parallel, and is connected to desktop. How to setup all and print wirelessly from laptop through WRT160N to printer on desktop?
I have a FIOS setup with their Router/modem providing DHCP and Wireless routing. The problem I have is that I have a mix of older equipment and newer equipment. The newer equipment is capable of supporting WPA2, the older is not. I would like the benefits of WPA2, but still would like to at times be able to use the older equipment.My solution was to use a WRT160N v2 router that I had as an access point and it also gives me switch capabilities for wired systems as the FIOS router in on a different floor than the Linksys router. Wired access works just fine and the wireless worked fine until just recently.Since both routers have the same default IP addresses I changed the Linksys to a different static IP and turned off DHCP. I left all of the other defaults the same. I set up the Linksys for WEP and created the key for security. Everything worked fine for the better part of a year, but recently I am having problems where some of the computers cannot find the network or find it then lose connection.
I am considering to purchase a Linksys Wireless router, but I just don't know which one to select.There are so many different types that seem to have very similar (if not equal) specs.If I just limit myself to the WRT120N, the WRT160N and the E1000, they all have 4 ethernet ports (10/100), and they all support 802.11 b/g/n for the wireless part.Obviously they all promise a blazing performance, and wireless coverage throughout the whole house, without (many) blind spots.But if their specs are the same, why are they different types?
I have a WRT 160N v2 router. There's 1 computer wired to it, that works fine. Then I have 2 laptops and a pc wireless to it. One laptop is a mac and that seems to be fine, another is a Compaq notebook that has trouble connecting and the pc has the same problem. The signal strength is very good to excellent so thats not the issue. What happens with the pc is, it will connect but at times its only for a few seconds then it disconnects. Sometimes restarting the computer fixes it for a while but it will eventually start having the problem again. It detects the wireless network just fine, and the router's firmware is up to date. I have a feeling that its the settings in the router but im not sure what to change.
I have two computers on hard line and two laptops. All computers on the line work fine and flawlessly. But when I try to connect the laptops to the computer, they say there's a problem with the certificate. Both detect the connection, and with strong enough signal strength. I've tried WPA and WEP encryption methods, and disabling encryption methods. All had no change. I believe the problem lies with this Wi-Fi Protected Setup stuff, which I have no clue as to what the hell it's supposed to do. I've tried disabling it by turning it to manual, which all computers then lose internet connection entirely. Browsing the FAQ's, I havn't found a solution. I've been working on this thing for a solid 7 and a half hours straight, and phone support is trying to make me configure static IPs, which proved extremely inconvenient in the past.
I just bought a Linksys WRT160N router. I pop the installation disk in my mac book pro and walk thru the installation procedure successfully.But I can't connect wirelessly from my MacBook Pro (running mac os x 10.5).It sees the router and I did type in the password correctly (i copy from the text file generated by the installation procedure), but I keep getting 'coonnection timeout'.
My Linksys WRT160N wireless router stopped working all of the sudden. When I connect to the internet wirelessly my laptops say I have full signal but "No Internet Access." None of the 4 wired ports on the back of the WRT160N router give me wired internet. The only way I can get internet is to connect the wire to my internet modem
I selected: Static IP Static IP:192.168.0.100 Subnet: 255.255.255.252 Gateway:192.168.0.1 DNS: 18.104.22.168
I am a Malaysian, using Streamyx here, I search some articles shows that the ISP given is 22.214.171.124 or 126.96.36.199. Am I right in the setup? Why I am still unable to online though successful to connect after the setup configuration?
I have" a WRT160N but I guess we had a power outage while I was on vacation and now I can't connect to my old network I set up.I see the Linksys internet connection and I can connect but its not the password protected one I set up. When I go to "manage connection" I can see the old "house" connection but can't connect
A few months ago, I purchase, installed and configured a WRT 160N V3. And I couldn't be happier. I now would like to go back and change the passphrase that a user needs to enter when they connecting to my router. Currently it uses the default value. And I would like to make it a bit more friendly. I found a number of postings dealing with setting retrieving or changing the Admin password.
But I was not able to find anything on changing the “passphrase”. There probably are a number of postings on the subject, and I simply overlooked them.
I just figured out how to bridge my modem, it was working perfectly. I was walked through by my ISP. So I KNOW it's correct.When I go to set up PPPoE with my WRT160N V2 router, I seeUsername:Password:Service Name (optional)(unchecked) Connect on Deman: Max Idle Time(checked) Keep Alive: Redial Period 30 secondsI KNOW my user and pass are correct but i still have no internet when I bridge my router and put in the info.My modem has DHCP turned off so i turned it off on my router too...nothing.Basically what all settings do I need to change in the ROUTER ALONE to make this work when setting up a PPPoEbtw setup is
I have a Router WRT160N and need to connect an Access Point using a wireless bridge (i.e. cannot use cable between router and AP). Which Linksys Access Point model is recommended to use with this router?(No I dont want to use another WRT160N with DD-WRT!)
While trying to add my kindle fire (unsuccessfully) I lost all internet connections, now my laptop won't connect. I reset the router and and can see my wi-fi account but when I try to use on my PC and laptop it won't recognize it.
I am attempting to block Facebook on a WRT160N firmware v3.0.00. I have a successful policy that blocks edit.com for instance and attempted to add url... I don't want to add keyword blocking as multiple news articles are in regards to Facebook. We simply do not want the Facebook website allowed. I tested the other policies on a network-wide setting, applying it to all IPs successfully, added Facebook to them and it goes right around the block. My guess is that Facebook is most likely designed to make it purposely difficult to block.
I went through the recent articles in search, but they primarily dealt with incorrect application of the policy (spec'ing MAC, or IPs), which isn't the case here. Eventually I will apply the policies to specific Macs, but I want them to work first.
I have a WRT 160n I want to use as an access point. The cable company has provided the main router so I want to use the 160 as the access point. I have a switch attached to the router and have the 160 attached to the switch. I can ping and access the 160, however there signal strength has not changed and is still extremely low. I know that the strength on the router is very good when I plug it in to the cable modem.