I'm trying to determine what switches in the Procurve lineup will do Inter-VLAN routing on the same switch. Assume a basic 1 switch network.
I've determined that Procurve "Layer 3 Lite" will do static routing but not dynamic routing. So I would assume their Layer 2 switches do absolutely no routing. However I have a 2520 in front of me that HP claims is Layer 2 only yet I can route between VLAN's on that switch.
we're running some HP ProCurve 2520's (24 port PoE for desktops/phones) and 2510's for our server racks. The CPU's are a bit weak from what we can tell and sometimes end up with issues on them. The specs on the EAS series look like a decent jump compared to the older HP's. However I've never worked with these ever.
My other option is to go back to Cisco. However to make it fit our budget, we have to dump gig switches for 10/100 + PoE. Which isn't really a major issue on the desktop switches. We'll naturally put gig versions on the server racks. I like our ProCurves, however they cause issues from time to time.
I've also considered going back to Adtran, however I haven't kept up with what they have to offer. I'm tempted to play it safe and go the Cisco route. We're using ASA5510's active/passive for routing/firewall (gig versions).
I have a situation where two of my CGS-2520-16S-8PC switches are not applying POE power to the copper ports, but showing power inline, two ports are showing power applied. Shutting down the port and re-enabling it will return the port to normal and the phone will connect.
I'm running cgs2520-lanbasek9-mz.122-58.EY2 after using 122-58-se1. Happening on both, but i have more switches running EY2 with no issues at the moment. Using DC power supply averaging around 53v.
We have two publicly routable gateways attached to our A5500 switch that are expecting untagged traffic.
We currently have VLAN 10 as the untagged VLAN for Gateway 1, and VLAN30 as a tagged vlan for Gateway 2. Since both gateways are requiring untagged traffic, I need to make sure all ingress traffic from Gateway 2 gets tagged as VLAN30, while all egress traffic gets untagged.
The tricky part is they must come over the same port so I can't just tag it that way. I get the feeling this will require some static routes or VLAN Interfaces on the switch, but I'm not sure where to start.
I have a HP Procurve 5406 connected to a Cisco 3560 on a temporary cat5e connection and I have Mitel IP phones needing to go on the Cisco switch.Ive configured the HP Procurve port to TAGGING both VLAN 10 (data) and VLAN 20 (Voice). NO is selected for default VLAN 1.The Cisco is configured on the port with switchport encap dot1q and switchport mode trunk.
Ive configured an IP for interface VLAN 10 and i cannot ping it from across the network. The interfaces are up and happy. I have tried changing the VTP status from transparent to server (VTP pruning is off) ive tried setting allowed vlans 10,20. Still not a think. The worse thing is that i have a working Cisco switch with the HP procurve that i checked the config on and its the same! The only difference is that the media type is SX over SFP in that case.
p.s not that im at this stage yet but i initially configure the FastE ports as trunks with native vlans because i was using non-cisco phones. On a spare port i convigured the voice vlan 20 and i say on the mitel phone that it was looking on vlan20! I didnt expect that, i thought the Voice VLAN ID was carried on CDP enabled devices only.
I am facing this trouble since i purchased this laptop i have a Dell vostro 2520 running on windows 8 pro X64, so the problem is that whenever i try to install drivers for Ethernet which i downloaded from the drivers and download section of this website it gives me an error "Realtek network controller was not found If in deep sleep mode please plug in the cable" now the thing is that it cannot be a problem in my windows as i was running on windows til few days ago, I got the same problem in windows 7 as well,
I have searched everywhere and i have tried almost every solution i got but to no avail the problem still persist and i cannot use LAN for Internet or file transfers,
P.S:- I looked for the adapter under the "control panel system and security system device manager Network adapters" But didn't found anything there saying Ethernet or something like that.
I am uploading the screenshots of the problem i am facing.
Unfortunately I do not remember the model and the switch is a couple of hours away without remote access.I have 4 vlans on a procurve switch.
VLAN1 - Network Devices (Server, printers, WAPs)
VLAN100 - Admin (Office workers)
VLAN200 - Teachers
VLAN300 - Students
There is a server doing DHCP. There are 4 ranges of IPs 1 for each VLAN.
The router is on Port 44. VLAN 1, 100, 200, 300 - Tagged
The Server is on Port 46. VLAN 1 - Untagged
The WAPs are on Ports 1, 11, 31 VLAN 1, 100, 200, 300 - Tagged
All other ports are on VLANs 100, 200 or 300 - Untagged
The WAPs all have VLANs 100, 200, 300. Each VLAN on a different SSID.
I have IP helper with the server IP on VLANs 100, 200, 300.
There are IPs from the different subnets on their respective VLANs in the switch.
The gateway for each subnet is on a different subinterface on the router.
The router is a linux box. (Untangle)
The WAPs are not able to talk to the server, therefore no computers on the wireless networks can get an IP.The server can only talk to the router if I change port 44 to untagged.What combination of tagged and untagged ports do I need to make everything talk?
Do I need to put the VLANs on the subinterfaces of the router?
I have 3 switches
Catalyst 2960
Catalyst 3750
Hp procurve 1410 24g
I want to link them using fiber as they are almost 50 meters apart. What connectors should I use and what fiber optic cable can be connected to those connectors.I have found these connectors and cables on internet will these work
GBM-7000-S85 - 1000Base-SX, multi-mode, 550m, 850nm GBIC transceiver
SC to SC Multimode Duplex High Speed Fiber Optic Ethernet Patch Cable 62.5/125
I have 2 procurve switches
2848
2650
Procurve stacking? Is that just a way too manage both switches together?
Or is it for combining both switches together?
Or is that called something else in procurve speak?
Or is that feature not actually available etc?
Next to learn how to breakup the 2848 into multiple switches.
I'm trying to configure Hp1810-24G and pfsense firewall with no success. I' would like to create two virtual lan on swich which share same internet connection. To simplifing I suppose
vlan 2 port 1-12
vlan 3 port 13-23
port 24 pfsense lan connection
What altready I do on pfsense I create vlan 2 called 1STVLAN VPID 2 and vlan 3 called 2NDVLAN VPID and assigned to them to LAN pfsense real port enabled and gived a static ip to them on HP procure I create two vlan with
vlan 2 port 1-12 untaged 13-23 Excluded 24 tagged
vlan 3 port 1-12 exluded 13-23 untagged 24 tagged
the problem is that I don't be able to speak with pfesense (ping failed on real lan ip and virtual lan ips) so I don't have also internet connection.The ethernet card i'm using are old (i have built the pfesense computer on spare parts that I have at home) so can be a driver issue?
I have configured stack with 2 sge2010p switches. I want to connect this stack to the HP procurve switch using port agregation (LAG) technique. I want to use one ge port on each sge switch.How to configure it? Will it work witch port agregation on procurve?
View 2 Replies View RelatedSo we recently moved our Comcast demarc to our new server room which resulted in moving the SMC modem from our old server room where it directly connects to the firewall - to a new room where it connects to a 2910 switch, LACP to our L3 switch, LACP to another 2910, then to Sonicwall.
Since the move our internet has been dropping off randomly for about 2-5 minutes then it will come back online. This happens anywhere from 10 to 50 times a day. Sometimes it happens a half hour apart, sometimes it is 15 minutes apart, sometimes it will go 8 hours without issue.
The modem has been replaced, the Comcast line has been "tested."
The modem remains online when we lose internet connectivity - I can connect to it using a laptop on it's lan port and ping out to google.com while an computer connected beyond the switch and sonicwall cannot connect.
I have run a constant ping from a home comptuer to the modem as well as to our sonicwall (both static addresses) and they both seem to go offline when we lose internet connectivity.
Since the issue started, I moved the Sonicwall so that it connects directly to the 2910 that the modem connects to, put it in a vlan with the modem so they only talk to each other and it still results in the same intermittent disconnects. I checked all the port statistics on both ports as well as the event logs, and trunk links and find nothing abnormal.
I take the switch out entirely and plug the modem directly into the firewall like it was prior to the whole move. Works fine.
Traffic is not an issue and the switch in question also connects all my production servers and iSCSI SAN together without issue.
I have:
-Procurve 1810-24G
-Procurve 2520-8-PoE
Router (with Internet Connection) is plugged into port 24 of the 1810.My asterisk server is plugged into Port 1 of the 1810.The 2520 is plugged into Port 2 of the 1810, and all of the VoIP phones are plugged into the 2520.Rest of the office computers are plugged into the remaining ports on the 1810.
After setting up the subnet and assigning an ip to the 1810, everything else just worked out of the box. I would imagine that I should segment and prioritize the network so that the VOIP traffic is isolated and is higher priority from everything else.
I tried playing around a bit, but the phones lost connectivity, so I just defaulted everything back for now.
What would the suggestions be for setting up the VLANS properly to do this?I would also need one of the office PC's (say the one plugged into port 13 of the 1810) to be able to access the asterisk server.Also, would it be more optimal to have the asterisk server on the PoE switch or the main switch?
My current switch layout at work is very basic and offers no redundancy. I'd like to at least setup redundant core switches, so that if any of my switches would to fail, it would result in a smaller number of systems affected.
Current Core Switch: HP Procurve 3500yl-48G (3500yl-24G as cold spare)
Internet Switch: 3com (forget model)
User distribution switches: 9 Planet 10/100 Layer 2 Managed switches, and 2 Dell Powerconnect 5448
Server switches: 5 Procurve 2810-24Gs (1 in each server rack)
In addition, we have 50+ site to site VPNs using different 192.168.x.x subnets across 2 different VPN concentrators, several routers, and a pair of MPLS's.My first step to improve speed and reliance was to reconnect the user switches. The old distribution switches were daisy chained, and all users 120 users were on a single 1GB port on the core switch, and if switch 2 of 11 failed, I'd have 10 switches knocked out of the network. I've since connected them directly to the core switch, and the users have noticed the improvement.
I'll try to get a diagram, but it's basically a large hub and spoke. Each and every switch is connected directly to the single core switch. All of the internet sources are connected directly to the 3com and are on separate VLANs which are then connected to the core via a trunk, which then handles the routing. Currently, I'm using less than half of the ports on the current core switch, so I should still have enough ports on the 24G to at least maintain the critical systems. Each server switch is trunked to the core, as is the internet switch, but the user network is not (but probably should be). Instead they are connected via simple untagged uplinks.
I absolutely cannot afford new equipment right now, so whatever I do will require reusing existing equipment. I'd very much like to increase the bandwidth from the server switches to the core if at all possible. Is there an easy way to configure and Active-Active setup that would improve bandwidth? Or would It be active-passive and require a 2 port LAG on the 48 port (for speed), and a 3rd port for the 24 port (for redundancy).
NOTE: With any luck, we'll be dropping our analog phone system and replacing it with VOIP sometime within the next year. So I should be getting some extra budget to replace the distribution switches with POE. Until then, I'll have to live with my crappy Planets.
Any good 24 port rack mountable Gigabit switch, that is managed. Is a HP ProCurve 1800-24G 24 port gigabit ethe switch J9028B decent ? Will i be happy ? I have currently a Dell 5224, that works, but it's getting old and for the life of me can't find rack ears AT ALL!! and i want it mounted so i can finish my rack installation.
budget is around 250-300$ 24 ports all gigabit and manage able for vlans etc etc.
I work as Network administrator in a building products plant at Poland. We had core switch HP Procurve 6200yl with 5 vlans, and 11 Aironet 1240AG Access points without controller. I have a problem with create 2 wi-fi VLANs on the Cisco AP's and linked it with HP switch.
VLANs on the switch:
1 - Default (for office sutff) - working great,
2 - Production (for production stuff) - working great,
3 - Inter (for Router's) - working great,
4 - WMS - i need configure it as wireless,
5 - WiFi with Radius - i need configure it as wireless.VLANS on the Access Points:
4 - WMS - for warehouse terminals - WPA2,
5 - WiFi for office stuff with Radius.
I'm easily able to get it running a single SSID (non-VLAN) network and confirm that I can use that network fine. However, I need to set up these 2 VLANs. I can connect to it via telnet if that'll let me program it faster.
I have a problem putting a Cisco 1141 AP in repeater mode with a AP HP Procurve.Root AP is a the Procurve, but when try to put the Cisco AP with same SSID, Authentication, etc, I receive this error:
%DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: NO Aironet Extension IE
I try disable the Aironet Extensions and always get the same error all time. It's possible connect both APs?
I am having difficulties implementing Mac-auth on selected ports between an HP ProCurve 2510 and Cisco ACS 5.3.The 802.1x works just fine, but for selected ports I need to implement port-access with MAC-based authentication instead of regular 802.1X (yeah, I know, but this line of ProCurve switches only support one auth-mechanism per port!).The switch successfully forwards interesting MAC-auth requests for authentication to the ACS with CHAP/MD5, but the ACS reports this:
Logged At:
April 16,2012 1:20:48.080 PM
RADIUS Status:
Authentication failed : 22056 Subject not found in the applicable identity store(s). NAS Failure:
Username:
002655886b3d MAC/IP Address:
00-26-55-88-6b-3d Network Device:
[code].....
The ACS is configured to use the Internal Hosts database, where the client computer is configured like this;MAC-address: 00-26-55-88-6B-3D
I wanted to know if I can somehow setup my network to use a proxy for all connected devices?
For example I can go into Firefox proxy settings and setup to browse using proxy. Is there any way to do this at the router or switch level to not have to configure every device individually I have a wndr3700 router and a HP procurve 1810g switch and am thinking of building a pfsense box.
We have a HP Procurve 5412zl switch as our default gateway for all our VLANs from there the traffic will be going to a Cisco ASA 5515 and then to a Cisco 3800 Router then to our ISP.
We have yet to purchase the ASA but my question is about my future configuration. I will have the router of last resort on the 5412zl setup to point to the ASA inside interface, how does that work with multiple VLANs? For instance the ASA inside interface would be 10.0.0.1 but traffic could come from another VLAN via the switch with a 192.168.1.x address. Would the ASA just pass it on to the router? Or would it conside this spoofing and drop the packet?
Lastely, if we have WCCP set for the ASA's inside interface, how would it handle the redirect for multiple VLANs ip addresses? Would I use GRE for the redirect to my web filter?
I have a very basic question about Cisco ASA 5505 IPsec Site to Site VPNs. I want to install a Cisco ASA 5505 at a Data Center, in a LAN subnet that utilizes publicly routable IP addresses. I would like to install a second Cisco ASA 5505 in a remote branch office as its peer.
Regardless of whether I use publicly routable IPs at the branch office in the "inside" network or non-routable IPs, how would the devices and servers at the Data Center know to route IP packets destined for the branch office back through the Cisco ASA instead of through the default gateway at the Data Center? I can see accomplishing this if every single device at the Data Center is configured with routing table entries, but that isn't feasible. It also isn't feasible to use the Cisco ASA 5505 as the default gateway for all of the devices as the Data Center, allowing it to decide where the traffic should go.
Is the solution to try to map branch office IPs to IP addresses within the Data Center's LAN subnet so that all of the traffic is on the same subnet?
I recently installed a very basic version of XP on my old laptop (Gateway MT3707).After hours of searching for the correct drivers, I found them, and installed them. After installing the correct drivers for wireless internet I was able to pull up the list and find my network on it.When double clicking on our wireless network it asks for a network key (also called WEP key or WPA key).Now we have a password for our network, but after an exhausting amount of tries that won't work. I not sure if that is what its looking for. In our apartment we run mac OSX, windows vista, etc., but usually the password for the network is satisfactory. I have never ran into this problem.I hate to be a noob, but I don't know where to go from here.
View 6 Replies View RelatedA month ago my ISP was routing half my subnet (129-254) over DSL. I just moved and routing no longer works without NAT. The issue is probably with the new DSL 'modem,' a zhone 1611-A1, but I am not sure how it should be configured.The 1611 is connected to a WRT610N, which works in NAT mode with the following settings:[code] With the previous settings, networking doesn't work from a workstation, though I can traceroute from the 610. I would like all workstations on the "LAN" to have fully addressable internet addresses like the previous configuration.There is an admin interface on the 1611, but the cursory settings I've tried don't work and I'm not a routing expert. The ISP is kindly routing my network, but they don't provide much support.
View 11 Replies View RelatedHaving some serious problems on the networking front here at home. I have 3 PC's and 2 Xbox's that run constantly. Our Internet bandwidth is Insight's 50.0 which is 50Mb download speed 5Mb upload speed. The problem we're having is this. Ever since we upgraded from dual 20Mb lines on a Cisco RV042 to a 50Mb on a DIR-655 we've been having latency issues. I have everything turned off in the router. It's basically there to give out IP numbers and thats it. All security is handled from the PC's themselves. Bandwidth tests are fine, I sustain download speeds above 7MB/s using download managers. But pings are terrible. Xbox live is terrible, PC online gaming is terrible. Pingtest.com is terrible. Only when behind routers. I've tried it behind 3 seperate routers. The DIR-655, the Belkin f5d8236 that insight provided me, and the cisco rv042 originally used for dual wan routing. all of which are met with serious failure.
If I plug directly in to the modem pings are fine. Add a router and pings go to shit.
I have 3 LAN connections. I m using 3 modems and 3 switches to connect all the pcs in LAN.but now i want 1 pc as a server which have connected all the 3 lan network with it.so that everyone can share its file to server and even all clients. Should i have to create VPN or homenetwork to connect with server? and i must have to install microsoft windows server in server pc?
View 4 Replies View RelatedMy laptop (Win 7 x64) can currently access all the shares on the XP computers in my home network but,although I can see it, I cannot access the laptop from my main xp computer. I haven't tried to access it from the other xp computers downstairs. I have read the guide on this site as well as 3 or 4 other threads on this subject but am unable to resolve the issue. Completing the network setup so that I can look into my laptop from this main xp computer. My laptop has a wireless internet connection but I also have it plugged into my wired home network for sharing. I will provide other details as needed. I suspect that some essential services for file sharing may not be running on the laptop, but I'm not sure.
View 19 Replies View RelatedI have been looking at ways of networking my printer in my office. The problem being that my printer does not have any kind of inbuilt networking capacity.So I thought I could connect it via USB to my router as it has a USB port on it.The router is an Orange Bright Box - In the specs for the router it says that the USB port is for file sharing, mentions nothing of connecting a printer to it
View 2 Replies View RelatedTrying to network between a Windows 7 computer and a Windows XP computer is possibly the hardest thing I have ever done.I have googled for hours and hours and none of the solutions seem to be working.I will try to explain what I have already done. Although I have done loads and I am sure I am missing some things.I have a Windows 7 laptop and for this exercise I shall call it WIN7. I have a Windows XP computer and for this exercise I shall call it WINXP.Both computers are in the same network which I have called SAMNETWORK. I have enabled permission to Everyone in folder sharing settings on WIN7. I have turned on Sharing and I have made myself discoverable with no password set on Network and Sharing Advanced Settings. Both user accounts on the XP and 7 machines are the same and both passwords are the same. I have turned all firewalls off. The WINXP computer has sharing enabled.
I have done a lot more things including installing LLTP (sp.?) and changing registry entries like Lsa/anonymous something like that (can't remember the actual directory) but I have changed registry entries as I have read elsewhere on the web and I have changed the network from home to work but that did nothing etc. etc. But everything that everyone suggests is just not working and I have been looking for about 4 hours now so you can imagine I have tried everything I have found!Anyway, my 7 laptop can see WINXP but when I click on it, it states that Windows cannot access \WINXP. The WINXP computer can see shared folders from WIN7 but it also states that it is not accessible. However, I did once get the WINXP computer to access the WIN7 shared folders. However, that doesn't even work now. I need the WIN7 to access the WINXP files. [code]
Running Windows XP Im a bit Dizzy as i can't seem to workout what's going wrong or what im doing wrong lol!!!8 Pc's on the network, all can view files etc.apart from one Pc Lets just call this "Bob1"It keeps asking for user name and password, now there's no user name or password on the giving pc, file and sharing is open and all the right ports giving. what i can't understand is that the reaming 7 pc's on the network has the same setup and files permissions, on the same subnet and can ping each other to my knowledge.So just to prove myself wrong i made a password for the pc that was asking for one on the network and this still did not work.so to cut the story short 7 pc's can search each other fine but on "Bob1" keeping asking for user name and password.
View 3 Replies View RelatedI am having trouble with setting up connection between pc using windows 7 and a laptop using windows xp. Do I have to setup a separate network on my laptop?
View 1 Replies View RelatedI am trying to use the existing rg-6 in a building for internet but am not sure how far a coax can go and still get a good signal strength?
View 1 Replies View RelatedI am trying to add an XP computer to our (already) Win7 computer.Now...I have connected the xp computer to the external modem that gived the 7 it's signal by way of ethernet cable). I went through changing and matching up the workgroup names, and.....turned on "Network Discovery" on the 7 end....after everything is said and done...I DO get the internet signal to the xp, but knock out the 7, altogether.
View 4 Replies View Relatednetworking error which seems to make no sense to me, i have computer 1 (tower computer) computer 2 (laptop computer 3 (tower computer1 & 2 have networked happily together for 4-5 years, sharing files and printers both ways. 3 was connected and happily joined the network but only with 2. 1 can see files on both 2 & 3, have now disconnected 3, have reset and rebooted router and both computers are up to date with software patches, i can not work out why 2 (or 3 before it was disconnected) can see 1 on the workgroup but can not access 1 in any way. i can, however, copy a shortcut from 1 through metwork places into 2 and access those files from 2. but network wizard or manual setting can not get full sharing.
View 6 Replies View Related