Region : Romania
Model : TL-WR720N
Hardware Version : V1
Firmware Version :
I have to clone my MAC address of the router to share my internet. To do that i have to visit htt://192.168.1.1 , but that address doesn't work for me..
Region : Bangladesh
Model : TL-WR720N
Hardware Version : V1
Firmware Version :
ISP : Is pros
After i bought the router it was working perfectly. But after using 1 week it freezes now and then. Happens around 10-30 times a day. The one or two led lights stops flashing and no device can connect to the router or asses internet. Another issue is that sometimes i cant connect any device through wifi (tried with android phone and ipod) and and but works perfectly on my pc. If i restart my router is works perfectly but after 1 min-3 hours sames problem happens either router freezes or cant connect though wifi
Region : UnitedStates
Model : TL-WR720N
Hardware Version : V1
Firmware Version :
ISP :
Just bought a new TP-Link TL-WR720N router. Hooked it up and got internet access just fine. However, when I go to [URL] or http://192.198.0.1 to try and login to setup the router, I just get the standard message:
Username or Password is incorrect. Please refer to the troubleshooting below:
Is the "Caps Lock" enabled on your keyboard? The username and password must be lowercase, please ensure that the "Caps Lock" LED is disabled on your keyboard and try again.Forgot your username or password? Please reset the device to the factory default settings if you have forgotten your username or password. The default username and password are both set as "admin". Note: The settings will be restored to factory default after the resetting.How to restore the device to the factory default settings? Firstly locate the reset button on the rear panel of the unit, whilst the device is powered on press and hold the reset button for more than 5 seconds, the device will then reboot and restore itself to the factory default settings. I am using a Cat 5e ethernet cable, I don't have NOD32 or any other antivirus or firewall blocking access, I even changed the settings and disabled IPv6 via ethernet since that was also suggested in the FAQ, but I still don't get a login screen.
I reset the router, rebooted my computer, unplugged the modem/router, reset everything again, double checked the IP address and pinged the router with excellent results, but nothing makes it so the login screen appears.I then hooked up the router to a PC running Windows XP with Internet Explorer 8 and the login screen works fine like you would expect. Went in, adjusted settings, everything works ok. This router is very new, it should support Windows 7 and Internet Explorer 9, shouldn't it? I don't want to have to keep old computers around just to login and change settings on my router.There must be some default setting in Windows 7 or in IE9 that causes this issue with the TL-WR720N router. I've tried everything that seems to cause the same issue on other routers, both TP-Link and other brands, and none of those seem to be what's causing this. TP-Link might want to address this ASAP and fix whatever causes it, otherwise this router is not going to do very well in the marketplace if setting it up with Windows 7 PCs with IE9 is a problem. It should work with default settings, same as it seems to with Windows XP and IE8.
I am trying to clone my mac address for the dlink router, DIR-655. I go to 192.168.0.1 and do not know my password. I have tried admin and no password, but it doesnt work. User name is admin, so it must be something standard.
View 1 Replies View RelatedMy ISP requires MAC authentication on the router for internet access. They provide the router, and register that router to their access list.I'm not very happy with the router they provided, so I'm planning to buy a E1200 and clone my current router's MAC address. But when I checked the interface of this router, the mac cloning page has a button saying "Clone my PC's MAC". And in the FAQ page of E1200 it says that the router can automatically capture the MAC address of the PC. Which is not what I want to do.I want to manually input my older router's MAC address into this router to clone it.
View 1 Replies View RelatedWe have an ADSL connection and use a D-Link DSL-320B modem. We have a D-Link DIR-120 router connected to this modem. This has worked perfectly fine up until today when we disconnected the router and connected a computer (call it A) directly to the modem because it was getting an unusable connection through the router for some reason. We later also performed a factory reset on the DIR-120 router.
Unfortunately, after the above steps the router did not receive any IP address (through DHCP) from the ADSL connection anymore. During my attempts to debug this I noticed that my laptop (call it B) didn't get any IP address either (when connected directly to the modem). I noticed the following syslog entries repeating over and over while trying to connect: [code]
At this point computer A could still get a connection just fine tho (when connected directly to the modem).
I then tried to change the MAC address of the router to an arbitrary one (a copy of computer B's MAC address but with the last digit increased by one). The router still did not get assigned any IP address. Finally I tried making the router clone the MAC address of a third computer (call it C). C has never been connected directly to the modem. Doing this worked. After cloning the MAC address of computer C the router is immediately assigned an IP address and the internet connection works as it did prior to all this.
Now, my question is, why would computer B and the original MAC address of the router not be able to get an IP address while two other computers worked just fine? Why would changing to an arbitrary MAC address not work while cloning the MAC address of another computer did? Could the router's MAC address have been blocked by the ISP for some reason (and what could cause this)?
but my situation seems more like a blacklisting of some MAC addresses rather then allowing just a single MAC address.
I am going to replace my Netgear DGND3700v2 router with Linksys EA6500. I hope that the signal strength of this router will be better, particularly for 5GHz.The problem is that I have a cable connection to Internet and my line has MAC address of Netgear assigned by my ISP. I would like to clone this address to EA6500 to test the power of the signal, before making the final decision to replace Netgear.My question is how to do this in off-line mode. I cannot have Internet before cloning.I've been using Internet Explorer with various addresses - 192.168.0.1; 192.168.1.1; myrouter.local; even 192.168.2.1 and some others but couldn't get connected to EA6500. Of course, the original CD suppied with the router does not work, either.Is there any other way to get to router configuration panel to proceed with cloning the MAC address?
View 1 Replies View RelatedRegion : UnitedKingdom
Model : TL-WR740N
Hardware Version : V4.23
Firmware Version : TL-WR740N_V4_130104
ISP :
not getting advertised 150Mbps speed , only getting 72Mbps installed the latest firmware TL-WR740N_V4_130104 and the performance is so bad that i cant even use skype anymore , the main reason to buy this router was to move from 54Mbps to 150Mbps but not sure what is wrong , how to achieve that 150Mbps speed
We can not get our PS3 to stay connected to the internet. We have Comcast and a Belkin router. We were told to clone Comcast's Mac Address to our router.
View 1 Replies View RelatedI'm running the 1522 as a bridge with v1.21 firmware. I have 2 devices wired to it. I have Wireless MAC cloning disabled (not checked). If I scan my network using a tool such as ipscanner (http:url.....) the devices attached to the bridge are being listed with the 1522's MAC address - not their own.
The connected devices should be showing up with their own MAC addresses. The 1522's address should only be displayed IF MAC cloning is enabled and IF the cloning mode is set to Auto - is my understanding of this feature incorrect or is my 1522 not performing as spec'd?
I would like to clone the MAC address of my ISP-supplied router to an ASA 5505 firewall to be used in router mode.
View 3 Replies View RelatedRegion : India
Model : TL-WR740N
Hardware Version : Not Clear
ISP : BSNL BB
I have a BSNL BB connection. When I use the connection directly, without adding TP Link router, all the websites open flawlessly. Once when I connect the wireless router, certain websites for example Yahoomail, pepperfry.com, yepme.com don't open at all. These are just examples, but I'm unable to access many sites which is a bit annoying. But sites such as gmail, youtube, facebook open clean, there are no issues. I didn't make any configuration changes too. I tried it more than three or four times, but there is a restricted access only.
-Region : Others
-Model : TL-WR740N
I am using TP-Link TL-WR740N as mentioned.Now I have a problem. In side my LAN I have four different PCs listening as Telnet Server at port 23. I want to create a telnet session over Internet with one of my PCs at a time.How should I do this? I mean what IP and Port number I should use to connect to my desired PC since all of my PCs are showing same public IP and that is of my router's IP.
Region : Australia
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP :
I am posting this in the wrong place but thats only because I cant find the forum for the TL-WR642G ver 3.6 device.Basically I am unable to see any QOS configuration and I wanted to know if this is available to this model ?I know the ver 4.0 firmware update states that QOS is added but can I update a 3.6 device using a ver 4.0 firmware ?
Region : India
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version : 3.16.3 Build 130104 Rel.55864n
I have upgraded to the openwrt firmware in my router. I am having some problem to use it because I dont have the GUI access. Anyway I want to revert back to my original firmware. I cant use the internet through my router. How to revert back to the original firmware
Region : Others
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
I bought today new TP-Link TL-WR740N and I connected it with my cable modem as it is in manual instructed. There is problem with outgoing signal from router. It is about 1/10 from it should be (it is around 2Mbps from 20 Mbps). Same speeds are going out from router through LAN port and WiFI signal.
Region : USA
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
Region : UnitedStates
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version : 3.16.5 Build 130322 Rel.59120n
ISP :
Even before I did the latest firmware flash I couldn't select short GI under Advanced Wireless - it was simply greyed out even though WMM was enabled above it. Now after a factory reset and recreating all my settings I still can't select it.
Region : Others
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP :
How can u acces to the setup TP-Link WR740N router who is WDS with other router ???
I make changes like this , WDS with TP link (IP 192.168.0.1) with adsl wifi modem who is main ip 192.168.178.1 it`s working but ,my ip from TP-Link modem is not working (192.168.0.1),only the addrees from mu first router is working 192.168.178.1
How to enter in my TP-Link modem, or i can`t , only factory reset
Region : Others
Model : TL-WR740N
Hardware Version : Not Clear
How can u acces to the setup TP-Link WR740N router who is WDS with other router? I make changes like this , WDS with TP link (IP 192.168.0.1) with adsl wifi modem who is main ip 192.168.178.1 it`s working but ,my ip from TP-Link modem is not working (192.168.0.1),only the addrees from mu first router is working 192.168.178.1.How to enter in my TP-Link modem, or i can`t , only factory reset
Region : Others
Model : TL-WR740N
Hardware Version :
Firmware Version : 120320
ISP : connect communication
HOW CAN I BLOCK USER FROM MY ROUTER WHO USES WIRELESS WITHOUT CHANGING PASS BECAUSE I WANT HIM TO KNOW PASSWORD BUT HE COULD NOT CONNECT
Region : Sweden
Model : TL-WR740N
Hardware Version : V4.20.0
I have a TL-WR740N. If router is on and I turn on my laptop it will not automatically connect to the router. I must turn off the router and then turn on again to get connection to the Laptop. I think I have missed something in configuration of the Laptop.
Region : Argentina
Model : TL-WR740N
Hardware Version : V1
my tp link router not working due to firmware or any other problem i dont know.when i powered my device 4 number port light is blinking without inserting cable and admin penal not opening i also try 192.168.0.1 or tplinklogin.net
Model : TL-WR741ND
Hardware Version : V1
Firmware Version :
ISP : EOLO
give me procedure for connecting WiFi to iPhone.The phone recognizes the router, but will not connect.No numbers, i.e. 192.168.1.1, etc are loaded No DNS loaded?
Region : Others
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 120320 Rel.51047n
ISP : Blic.net (Banja Luka, Bosnia)
I'm having issues with PPPoE connection. On a daily level, my connection breaks 1-5 times. In the past, it was related to signal problems, but ISP Tech. team fixed this some 10 days ago. Now, whenever I call them they say connection was broken on user request and ask me if I'm running services like torrents.
I don't run torrents and all I have is standard windows update services, nod 32, as well as steam client.
Here's router log from today when last error occured (I "blanked" some user-specific data like my username or MAC address).
773/31/2013 17:04PPPINFOrcvd [proto=0x8057] xxxxxxxxxxxxxxxxxxxxxxxx
783/31/2013 17:04PPPINFOsent [LCP ProtRej]
793/31/2013 17:04PPPWARNINGPPPoE link down
[Code].....
The 740N I got is pretty old now so I have another router and I want to use 740N as a bridge to extend my main router's wireless service. The main router has Mac Filtering enabled and I've entered the 740N's Mac address into the main router. I have switched off 740N's DHCP, changed it's IP etc. I can connect to 740N but 740N is not connecting to the main router. I've tried the same thing at my office where the main router is a 8961ND and I successfully bridged and connected the 740N but it's not working at my home.
View 5 Replies View RelatedI have a weird problem. I bought recently a new router, and when I try to connect to the settings on it on http://198.168.0.1 it sometimes works, mostly doesn't. When I ping other devices which are connected it, it's the same; sometimes get a response, mostly I don't. The router model is: TP-LINK 150Mbps Wireless N Router TL-WR740N, The thing which it's connected to is entitled "ADSL2+ Ethernet bridge router" That aforementioned thing is suppoused to be a modem. But, when I try to connect to its settings from http://10.0.0.138 , I'm able to, and other who are connected to the network give response to a ping.
View 4 Replies View RelatedRegion : Canada
Model : TL-WR700N
Hardware Version : V1
Firmware Version : latest
ISP : various
What would seem to be an ideal way to share a hotel wifi signal with other devices, would be:
Laptop signs into hotel/resort wifi and completes sign-in page. Share wifi signal with TP router via an ethernet cable. TP router acts as hotspot for connection by other devices. This is the method this Apple based article suggests:
[URL]
I have tried this with Windows 7 using a bridge between the laptop wifi and lan adapters. But I must be doing something wrong.
The other option is to use ICS, but not sure then if the hotel's system would see additional devices. (we are limited to 4 where we stay, but exceed that when family visits!)
Region : Hungary
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP : T-Home
I bought a TP-Link TL-WR740R Router, the setup went smoothly, I could connect to the internet and set up WiFi connection. But after a few hours, I accidentally unplugged the Ethernet cable from the router, and since then, I can't seem to make the router work. (I obviously plugged it back in.) Setup says I have a problem with the WAN connection.I tried rebooting, resting, reconfiguring, cloning the MAC address.The router is sending packages, but receiving none. How could this happen just by unplugging the cable for a second?
I have TL-WR740N router. ISP should provide me up to 100Mb/s internet speed. Actual measurements shows me about 80 Mb/s. The problem is when I enable 3389 port in Port Triggering my internet speed drops to 2,5 Mb/s. When I disable port triggering, speed become normal again.
View 3 Replies View RelatedRegion : UnitedStates
Model : TL-WR700N
Hardware Version : V1
Firmware Version :
ISP :
My TL-WR700N does its job to provide wired internet to my desktop computer from another wireless router via client mode. However, when it is connected, the other wireless clients connected to the primary router lose their connections. To restore those connections, the WR700N must be powered down and the primary router must be restarted.
Region : UnitedStates
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.1
ISP : T2
I have a problem with my tp-link router. I dont have an internet access of the router, updated firmware... When i connect to router by laptop the internet works fine, but when i connect to router by phone i have an internet access only 5 second and than i lost it, but still connected. I don't know what is the problem here, maybe phone?
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V3
Firmware Version : not sure
ISP : Talk Talk
My network is like this: ISP TalkTalk---ADSL modem-----TP-LINK TL-WR740N---Windows XP computer. I have configured the device by running the CD but it says failed to verify.Then I tried to refers to Quick Installation Guide (Manual) , there have offer a address 192.168.1.1 to go to web based quick setup wizard. But this site is not available.Other Wi-Fi devices are catching its signals even they are getting connected to it after enter the set up password and username but internet access has not been made so far.
Region : Hongkong
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP : PCCW
Just bought the router in Hong Kong to connect to my Mac. Typed in [URL] and everything is in Chinese with no link that I can see to change it to English. Is it possible to change the language?