I am trying to clone my mac address for the dlink router, DIR-655. I go to 192.168.0.1 and do not know my password. I have tried admin and no password, but it doesnt work. User name is admin, so it must be something standard.
View 1 Replies
Region : Romania
Model : TL-WR720N
Hardware Version : V1
Firmware Version :
I have to clone my MAC address of the router to share my internet. To do that i have to visit htt://192.168.1.1 , but that address doesn't work for me..
We have an ADSL connection and use a D-Link DSL-320B modem. We have a D-Link DIR-120 router connected to this modem. This has worked perfectly fine up until today when we disconnected the router and connected a computer (call it A) directly to the modem because it was getting an unusable connection through the router for some reason. We later also performed a factory reset on the DIR-120 router.
Unfortunately, after the above steps the router did not receive any IP address (through DHCP) from the ADSL connection anymore. During my attempts to debug this I noticed that my laptop (call it B) didn't get any IP address either (when connected directly to the modem). I noticed the following syslog entries repeating over and over while trying to connect: [code]
At this point computer A could still get a connection just fine tho (when connected directly to the modem).
I then tried to change the MAC address of the router to an arbitrary one (a copy of computer B's MAC address but with the last digit increased by one). The router still did not get assigned any IP address. Finally I tried making the router clone the MAC address of a third computer (call it C). C has never been connected directly to the modem. Doing this worked. After cloning the MAC address of computer C the router is immediately assigned an IP address and the internet connection works as it did prior to all this.
Now, my question is, why would computer B and the original MAC address of the router not be able to get an IP address while two other computers worked just fine? Why would changing to an arbitrary MAC address not work while cloning the MAC address of another computer did? Could the router's MAC address have been blocked by the ISP for some reason (and what could cause this)?
but my situation seems more like a blacklisting of some MAC addresses rather then allowing just a single MAC address.
We can not get our PS3 to stay connected to the internet. We have Comcast and a Belkin router. We were told to clone Comcast's Mac Address to our router.
View 1 Replies View RelatedI would like to clone the MAC address of my ISP-supplied router to an ASA 5505 firewall to be used in router mode.
View 3 Replies View RelatedMy ISP requires MAC authentication on the router for internet access. They provide the router, and register that router to their access list.I'm not very happy with the router they provided, so I'm planning to buy a E1200 and clone my current router's MAC address. But when I checked the interface of this router, the mac cloning page has a button saying "Clone my PC's MAC". And in the FAQ page of E1200 it says that the router can automatically capture the MAC address of the PC. Which is not what I want to do.I want to manually input my older router's MAC address into this router to clone it.
View 1 Replies View RelatedI am going to replace my Netgear DGND3700v2 router with Linksys EA6500. I hope that the signal strength of this router will be better, particularly for 5GHz.The problem is that I have a cable connection to Internet and my line has MAC address of Netgear assigned by my ISP. I would like to clone this address to EA6500 to test the power of the signal, before making the final decision to replace Netgear.My question is how to do this in off-line mode. I cannot have Internet before cloning.I've been using Internet Explorer with various addresses - 192.168.0.1; 192.168.1.1; myrouter.local; even 192.168.2.1 and some others but couldn't get connected to EA6500. Of course, the original CD suppied with the router does not work, either.Is there any other way to get to router configuration panel to proceed with cloning the MAC address?
View 1 Replies View RelatedI'm running the 1522 as a bridge with v1.21 firmware. I have 2 devices wired to it. I have Wireless MAC cloning disabled (not checked). If I scan my network using a tool such as ipscanner (http:url.....) the devices attached to the bridge are being listed with the 1522's MAC address - not their own.
The connected devices should be showing up with their own MAC addresses. The 1522's address should only be displayed IF MAC cloning is enabled and IF the cloning mode is set to Auto - is my understanding of this feature incorrect or is my 1522 not performing as spec'd?
I recently switched routers to the DIR-615 and I'm trying to troubleshoot why one of our laptops keeps losing the IP address and gets a self-assigned IP address. I see the following messages in the log, I am wondering if the reason codes are listed and explained somewhere? I tried searching the manual but could not find any information.
View 9 Replies View RelatedI am sure this has been asked before, but how do you put in your own computer name into the MAC filtering?
View 2 Replies View RelatedI have 5 static public IP addresses assigned by my ISP. I like to use one of these static public IP addresses to access one of my PCs in my office from the outside. So I like to configure something like:65.11.22.44 <-> 192.168.1.100.This translation is good for all protocols and all ports. Where I can configure this on the DIR655?
View 2 Replies View RelatedI need a new ip address form my provider.I now that thy work with the mac address,How van i cahnge that in my dlink 655
View 5 Replies View RelatedI have a device(internet radio) that seems to require an address format of 192.168.xxx.xxx. The router does not do this range and I cannot set it to that range ( the first three xxx). If I try the router defaults back to 192.168.x.xxx. Any way to over come this so I can connect the radio (which works fine wired as the ISP can supply a 192.168.xxx.xxx IP address).
View 6 Replies View RelatedI have a D-Link DWL 520+ on my motherboard I can't get the wireless adapter to gain the IP address. I have tried to reboot and uninstall and reinstall, and repair. I have tried the hardware manager and several drivers from around the world (all being the same). Again the adapter can see the internet and connect with my router but it will not pickup the IP address. How do I get the wireless adapter to see the IP address?
View 1 Replies View RelatedI have set up DHCP reservations to assigned IP addresses based on MAC address. I have to block my kids access at times, and when I do this they simply change their IP address and they circumvent the blocking.Other than punishing the kids (which hasn't worked - and they need computers and Internet for homework), is there anyway to lock a computer to MAC address to IP address so if they change it they won't get network/internet access?I also tried to set up network filtering and I put in all the PCs and devices I wanted to provide access for, including the router, but when I save changes I can no longer access the internet or the router. I have to do factory reset to get back into router config.Also, I'm on 1.30WW. I know 1.34 exists, which I tried on a previous router which died and was replaced by RMA; but this didn't solve any problems.
View 6 Replies View RelatedRegion : Poland
Model : TL-MR3040
Hardware Version : V1
Firmware Version : recent
ISP :
I have a tplink mr-3040 modem to use as repeater for my travels in hotels and after 2 monts I was not able to make it to work any time.Whenever I try with WEP, WPA or OPEN - like today - it's always the same problem: I can see repeated network with strong signal, but when I want to connect using laptop or phone connection stop on level of "getting IP address" and never end with final time-out.
I cant really find anything about MAC address filtering in the tabs of the router administrator page.
View 7 Replies View RelatedRecently upgraded to 1.33NA. I keep getting this message when changing certain settings (such as enabling a guest zone). It's essentially locking me out of changing the system!As far as I know - the DIR-655 DOESN'T have WDS - this was removed a number of firmware revisions ago. I cannot find a setting for this anywhere. There are a few mentions of this on this forum and the web, but nothing concrete as to why it's happening or a valid solution.[url]...
View 6 Replies View RelatedI have a home desktop, home laptop, and work laptop that I use. I have Ultra VNC setup on my work laptop that allows me to remote into that machine when I am traveling for work. I have always been able to use the external IP address (not private) to login into the machine with no problem. This week, for some reason, I can no longer do that. When I started doing some discovery, I noticed that when I have all 3 machines booted up at home that the exact same external IP address is assigned to all 3 machines. The internal IP addresses are all different as they should be.Shouldn't each machine have a seperate external IP address assigned as well? Or is this working the way it should? I didn't change any setting on my router or DSL model. But I think the conflict that VNC is having on my work laptop is that it has the exact same IP as the destination computer and it fails. I can remote in if I use the private IP address (192.168.x.x) just fine.
View 1 Replies View RelatedI am on a University campus and they have provided the following to connect to the internet along with DNS server addresses:
IP Address: 192.168.25.24
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.254.1
When I connect my computer, it gives an error that the IP address and subnet mismatch, but it still connects to the internet just fine. However, if I try to put these settings into the DIR-655 along with my computer's MAC address, it gives me the error "WAN gateway IP address 192.168.25.24 must be within the WAN subnet" and requires I change it.
I've recently noticed an issue with the D600. A few days ago, I could not get any IP address from the router (wireless connection) on one of my laptops. I checked the router and it did something never done before: It restarted automatically (orange lights). Everything seemed to work fine but now when one of my device connects to the network (ps3, iPhone, laptops...) no IP address is given by the router so everything is on limited connectivity which is really annoying. I have to turn it off/on to make it work. It happens most of the time.
Note that I already returned the router a couple a year ago or so (I cant recall what was the issue), so I have to say that the quality of this device is far behind my expectations.
I have an AS-external route being redistributed into OSPF from a static route on one of my routers. I recently changed the static route from a /24 to a /26 and all of a sudden the link ID of the segment in the OSPF database went from the network address to the broadcast address: Code:
View 5 Replies View RelatedI brought this TP-Link wireless router months ago, and I decided to use it this time. Upon connecting the cables, all the lights are OK, however, during the installation, my pc cannot find the router. I read that supposedly the IP addresses of my PC and the router should be the same. But, even if i change the IP address (to 192.168.1.xxx), the computer still can't find it. Pinging it results to a timed-out request.
Windows IP Configuration
Host Name microsof-dhj0uv
Primary DNS Suffix
Node type
[Code].....
I installed the 2.06NA on my DIR-655 router and now I'm having problems adding mac addresses to the network filter. The message is "Invalid MAC address". Of course, it doesn't tell me which entry is invalid and I have a number of them. After further checking.. I noticed that one of the MAC addresses is indeed invalid and when I remove it I still get the error message?
View 1 Replies View RelatedI have an Avaya IP Phone for work. This has been tested at work and works as expected. After the IP Phone boots it's able to obtain an IP address from work. At home when I plug the IP phone into my DIR-655 router, it's unable to obtain an IP address. Other network devices are able to obtain an IP address, for example any computer or laptop. Also my wireless works with no issues expect for the IP phone. I've already done some searching and found other users with the same issue but I haven't been able to find a solution other than setting a static IP address. I'm curious why this relatively new router won't work with an IP phone. I've played with some of the router settings but it didn't make a difference. Any work around to get the DHCP to work? I'm running the latest firmware for my router: 1.35A Hardware Versions: A4.
View 9 Replies View RelatedI am unable to reserve an IP for my iPad, i.e. add my ipad to the "DHCP RESERVATIONS LIST". I get a pop-up saying "The MAC Address entered is invalid." The address starts with "D8". My understanding is most start w/ "00". The router says my firmware is up-to-date (3.01).
View 11 Replies View RelatedI updated my firmware to the latest update a and then restored My personnel setting and now I can not access my ftp, I checked my IP address to make sure it didn't change , setting looks like did before update I went from firmware 121 to 135, was there new setting that I have to change to get it to work. I get no log in screen I get Windows cannot access this folder. Make sure you typed the file name correctly and that you have permission to access the folder?
Details:A connection with the server could not be established
I had no problem running both 2.4 and 5.0 Bandwidth. With WiFi password and without. It does it's job. The 2.4Ghz Range Plus works. I have set up the router on the 2nd floor at the highest it can go. And everyone get's full bars all over the house. I even get 4-5 bars outside in my car on my phone.
The only issue I have with this thing is a damn new netbook I got for Christmas with a Mac Address starting with 0C-EE-E6-XX-XX-XX. The Router finds the Mac Address invalid. In which I can come to understand cause seeing a Mac Address starting like that is completely new to me. Every Mac Address I have, started with 00 except the netbook. So now, I spent days trying to find firmware updates, patches, anything! I even attempted to spoof the Mac Address on the netbook but Microsoft has a bug on Windows 7. (I have the Starter Edition that came with the netbook)
Windows 7 Mac Spoofing works with WIRED Connection. But it does not work with WIRELESS Connection. I used 3rd Party Tools: SMAC and etc... I attempted Registry Edits, I changed even the value key to the "Orginal Mac Address" and it just wont change [New Strings/Network Address Edits included]. I have been banging my head about this for a week now. The Internets has many answers but they did not work. So Spoofing the Mac Address is out of the question. Until Microsoft fixes this bug.
Anyway: Did D-Link release any sort of beta update/driver/firmware or anything to resolve this at all? Is there a modded firmware to force the Router to take this stupid paradox of a Mac Address?
Currently: I have the Router's WiFi Password-ed with Default Factory Settings
{Hardware Version: B1
Firmware Version: 2.02NA}.
I am having issues with wireless connections with my laptop but I can connect with my phones and iPod, however wired connections work perfectly.
The moment I attempt a wireless connection I receive continuous error messages saying that there is an ip-address conflict with another system on the network and i lose all internet access.I have already tried adding a dhcp reservation?
I cannot access my router through IP address or dlinkap. I am trying to connect a bridge for the living room in my house.When I do an IPCONFIG my default gateway as weird characters in front of the actual IP fb23:ff23 etc.
View 4 Replies View Relatedis there any way to interact with wan port like LAN?i have connected a rocket m5 as a bridge to my Dir-615 wan port but i cant see the AirOS login page (rocket m5 configuration page) nor brige's ip address on my LAN...is there any way to interact with the ip address that connected to wan port?
View 1 Replies View RelatedI've been using the Dir-655 for 2 or 3 years with my old Xbox 360 and an external G wireless adapter. Everything was working perfectly until I got the dreaded Red Rings Of Death the other day. I replaced the Xbox with a new Slim version with built in N capable network adapter.
After more than 10 hours of trying a variety of "fixes" I found from MS and in this forum, I am still at square 1.
Hardware Version : A3
Firmware Version : 1.32NA (this is listed as Live compatible by Microsoft)
802.11 Mode : Tried N only, G only and mixed 802.11n and 802.11g
Enable Auto Channel Scan : Checked
Transmission Rate : Best (automatic)
Channel Width : Auto 20/40
Visibility Status : Visible
Security Mode : WPA-Personal Also tried WEP
WPA Mode : Auto (WPA or WPA2) Also tried WEP
Cipher Type : TKOP and AES
I tried assigning an IP manually from the Xbox. But, no matter what I do, the router will not accept it. It is especially frustrating that the Xbox is visible to the unit. It simply will not assign an IP to it under any circumstance.
If you read the sales hype promoting the Dir-655, you will see a lot of nonsense about it being great for gaming. Given that, you'd think a simple solution would have been found and posted for this issue by now. Surely, end users shouldn't be trying 100 different possible "fixes", none of which work, at this late stage of the firmware upgrades. If I sound a tad fed up, it's because I am. After the expense of the new Xbox, it appears I now have to junk my router too.
Here is the status screen taken when it was in mixed mode. Changing it to 'G Only' didn't make any difference:
I have a fixed external ip address.I have port forwarding setup for accessing a NAS inside my LAN, lets say port 12345.Now when I use my laptop outside my own LAN, e.g. 99.99.99.99:12345 resolves nicely to my NAS. But when I use the same 99.99.99.99:12345 inside my LAN, it does not resolve. Instead, it gives me a 'server takes too long to answer' error
I have also setup a virtual host to an ip cam inside my network. That one resolves just fine. I tried enabling remote management on the DIR-655 and also that works fine using 99.99.99.99:8888.When I replace the external ip address with the internal ip address of my NAS, thus bypassing port forwarding, it obviously also works ok.
Why the forwarded ports are not accessible when I use my own external fixed IP address? Does the DIR-655 treat it different than other external IP addresses?
