TP-Link Dual-Band Wireless :: WDR3500 Tip To Increase Speed To Expected And Reasonable Value
Oct 30, 2012
Region : UnitedStates
Model : TL-WDR3500
Set this up last night and it went very easy with the excellent instructions. Transfer rate from computer A to computer B (wired) of a 1 gb file was 12 mb/s and that was from SATA 3 to SATA 3 discs. Using a gigabyte router those values were 55.5 mb/s. Even though this router is only 10/100 that speed is unacceptable. Is there a tip to increase that speed to an expected and reasonable value?Also, the router just quit for no apparent reason and needed a reboot. What are common causes that I might look into to see why this happened.
View 4 Replies
ADVERTISEMENT
Nov 4, 2012
Model : TL-WDR3500
Hardware Version : Not Clear
Firmware Version :
ISP :
As we say, I followed all the directions but I am unable to setup the ftp server on this router. I even disabled Norton's firewall but am unable to access the server via WAN.
View 4 Replies
View Related
May 13, 2013
Region : Others
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
wdr3500 problem with usb external hard drive when I try to transfer files from computer to usb on the router it'll work for small files like MP3. But files like MKV where they can be 1-2gb will cause a disconnect and fail to transfer the file. The whole drive would disconnect and windows will give an I/O error.
View 8 Replies
View Related
Nov 6, 2012
Region : Denmark
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : Arrownet
I purchased a WDR4300 yesterday and have set it up. The internet is running smoothly although the transfer speed is rather slow. When transferring from my computer to my Seagate GoFlex Home i get about 6 - 8 mbps with Wireless N. The router is set to only use Wireless-N and my laptop has the latest drivers. I have also tried other computers in the house and the speed is the same. The GoFlex Home is connected to the router via a LAN cable. Prior to updating i used a Linksys WRT54GL and managed speeds of about 3 or 4 mbps over its G only connection. As for transfers between 2 computes the rate is about 1 - 3 mbps
As for distance the Wireless router is only about 1.5 meters from the laptop (across the room) with nothing in between them to cause interference. I have also checked what channels my neighbors use (using inSSIDer) and picked 13 as there is only 1 other person nearby on that channel and they are quite far away.
View 5 Replies
View Related
Feb 10, 2013
Region : Russia
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP : VIMPELCOM
I have portable hard disk connected to one of the TL-WDR3600 router usb ports (another one has printer connected to it)
Write speed is about 3Mbytes/sec maximum.Real disk write speed is about 35-38Mbytes/sec - if I connect it to one of the PC USB ports (both router and PC ports are USB 2.0)Why write speed via router is so low?
My PC is connected to router via cable and is running Windows 7 32bit Ultimate SP1, hard disk partition is 465Gb NTFS single volume.I'm measuring speed simply by coping 1.4Gb file through Windows Explorer to \tplinklogin.net (following USB storage access instructions from router control panel) in first case and directly to hard disk - in second case.
View 1 Replies
View Related
Apr 28, 2013
Region : Others
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.31 Build 130319 Rel.57876n
ISP : Antel
I have a WDR4300 which works perfect with all devices in my house, but in my personal notebook (samsung 530U4B) wireless transfer speed is very slow in 2.4 GHz mode. 5.0 ghz works fine. I've tried everything, but I can not get good performance. at this moment I have to use a 741nd working with my wdr4300 in wds mode to use 2.4 ghz band properly.
View 6 Replies
View Related
Nov 8, 2012
Region : Romania
Model : TL-WDR4300
Hardware Version : V1
my Wi-fi card is an Intel Centrino 130N. When I connect to the Internet directly, the speeds I get are: DL: 11 MBs and UL: 9 MBs. (I know the difference between MB and Mbits). Although, when I'm connected through wireless, I get: DL: 3.4 MBs and UL: 4.7 MBs.how do I get my DL speed to be higher than the UL speed in wireless mode ? I read somewhere I have to disable QoS and WMM, but I simply can't find that option in the router's settings. even if I am in the same room as my router, when I check the status of the wireless connection, the maximum speed is 72 mbps. Should that be 130 mbps, as I run it in N mode, not G? How to improve that ? I have Win 7 and all the latest drivers and everything.
View 3 Replies
View Related
Apr 14, 2013
When you have both a dual band router, and a dual band adapter, does that give you a theoretical peak of 600mbps on the Adapter? or does it only connect on one frequency at a time from the adapter?
EG Dlink DWA-160 with an E4200.
View 1 Replies
View Related
Apr 2, 2013
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP : Centurylink
I'm using a WDR3600 router, and I'm having difficulty with getting internet access on the 5 GHz band. Right now the router is broadcasting in both 2.4 and 5 GHz as two separate APs. The 2.4 GHz band works perfectly fine, but when I connect to the 5 GHz band my device is not assigned an IP address and cannot connect to the internet (or even the router configuration page). Unfortunately, I don't have another device capable of accessing the 5 GHz band, so I can't check to see if the computer is at fault, but both the computer and the router have worked together with no problems before, and this computer has done fine in accessing other 5 GHz bands.
View 1 Replies
View Related
Feb 14, 2013
Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : Comcast
I just upgraded my DLink DIR655 to WDR4300. My VOIP service has worked for the last 5 years. But with WDR4300, I'm frequently experiencing dropped calls. The call will be cut off every 20 seconds or so. This is really a deal-killer.
View 7 Replies
View Related
Feb 19, 2012
i am going to purchase a Simultaneous Dual Band Router with Gigabit Lan. Can anybody tell me whats the transfer speed it got on Concurrent Dual Band 900(450+450) , 750(300+450) and 600(300+300). I am going to use it for hard drive that can network attached or may be just external hard drive via USB interface.
View 2 Replies
View Related
Dec 31, 2012
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23
ISP : Comcast
I have no problems connecting on a 5 GHz band or wired to the router. However any device connecting on 2.4 Ghz gets barely any bandwidth and drops after running for a short time. I have test numerous devices and have the same issue. What was odd is a device on 5GHz that worked fine had the same issue when connecting on 2.4 GHz which seems to say it is only that band. I have an old router that works fine on 2.4 GHz on channel 1 with all the security settings I used on the 4300.
View 14 Replies
View Related
Feb 18, 2013
Region : Netherlands
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 130129
ISP :
I've this dualband wireless router since a week.Now I found out, NFS is working very slow (actually NFS is not working at all).I have a Mede8er and a synology NAS server connected to the TP-LINK WDR3600 router.I have movie directories shared on the NAS using NFS.when I go to the NFS locations in my mede8er it takes very long before I can see the NFS mapping.When I connect the Mede8er straight to the Synology NAS server (Cross Cable connection) NFS is working as it should be.So the TP-LINK WDR3600 cannot handle the NFS protocol?
View 2 Replies
View Related
Mar 29, 2013
Region : UnitedStates
Model : TL-WDR4900
Hardware Version : Not Clear
Firmware Version :
ISP : Comcast
The internet connection works really well on the 2.4GHz connection and when wired. But when Im connected through the 5GHz network, I get no internet.
View 2 Replies
View Related
Nov 15, 2012
Region : Iraq
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : Newroz Telecom
Can I replace firmawre TP-Link WDR4300 to DD-WRT to use it?, either my TP-link already has VPN,NAT,QOS,..etc like as DD-WRT so does need to replace firmware for better?
Does TP-Link WDR4300 support with DD-wrt? Is it working clearly without any problem?
View 1 Replies
View Related
Jan 6, 2013
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : latest
ISP : Clear
Get GMT throws an error. I set known good public NTP servers, still get error. Also power cycling or rebooting the router seems to drop manual time settings, as well. I am using WDR4300 as a wireless access point, does that matter? Maybe I don't need time in access mode? It is connected to the Internet and is providing internet access to clients.
View 1 Replies
View Related
Mar 28, 2013
Region : Venezuela
Model : TL-WDR4300
Hardware Version : Not Clear
Firmware Version :
ISP :
I have an issue with my TL-WDR4300 (regular, internet sharing use, no Open WRT or similar things). It was working well, until one day that my devices only receive the 2.4 GHz signal (no 5 GHz) and then I try to connect to 2.4 GHz and it asks for a password. I put my regular password and it doesn't work. Then I tried to bring it to factory default settings, I push the reset button for 8 seconds as the manual points and then same thing. What could I do?
View 2 Replies
View Related
Mar 30, 2013
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version :
ISP : I have an external HDD that I regularly use in any computer I have access.It's an HDD enclosure 2.5" 3.0 USB, with a 750GB WD HDD inside. I use it in computers with all versions of USB, even in my TV. It doens't require an external power source, and just have 01 input/output, which is a USB port.After plugging it in the router (running with the last available firmware from TP-LINK - 3.13.27 Build 121207), I entered the setup screen of the router, and under USB Settings, pressed RESCAN, but the HDD wasn't recognized.What happens is that when I plug it in the router, the LED in it starts blinking (in normal usage, the LED becomes red for a couple of seconds, and then becomes steadly blue, when it gets connected into a equipment). It is probably a matter of power, as if the router wasn't providing enough power to it when it's plugged.Afterwards, I've made the following tests:
1) Used this External HDD in 3 different equipments (a notebook, a netbook and a TV), with different versions of USB ports. It was recognized and read normally in all of them.
2) I tested a pendrive with the router. After RESCAN, it was shown normally in Storage Sharing page.
3) I have downgraded the firmware to 120509 version, plugged the HDD in the router, and once again, it was an unsuccessful try.
What I can conclude from those tests is that:
1) My External HDD is working normally;
2) The router's USB port is working properly;
3) So, if both are working, it can only be a matter of compatibility between them.
View 2 Replies
View Related
Jan 14, 2013
Region : UnitedKingdom
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : plusnet
How do I get the full 450 Mbps out of my router on the status it saying 300Mbps
View 5 Replies
View Related
Nov 21, 2012
Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
Region : Others
I have Enable WDS Bridging and run Survey which detect the other SSID to be joined with the correct MAC address.I had filled the password of my second THOMSON v 585 V7 with the correct Auth Type both routers broadcast on channel 11.But my TP-Link 2543ND cannot made it work.I also disable DHCP and changed my LAN ip to 192.168.1.2 and can access it over my lan.
View 1 Replies
View Related
Mar 5, 2013
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
The router is working and when I plug in an external drive to usb I can see in the admin tool. It is setup to share without a password. I am using a PC with Vista on it...so I go to RUN and enter [URL] but I get the following message:'Windows cannot access [URL]
View 2 Replies
View Related
Apr 3, 2013
Region : Netherlands
Model : TL-WDR4900
Hardware Version : V1
Firmware Version : 121211
ISP :
after changing from a Thomson router with wifi to the TP-link WDR-4900 I find that the wifi is very unstable. The 2.4GHz is operating on the same channel as my previous router (channel 8 - which is the lest busy channel around my house), and none of my neighbours have wifi on the 5GHz band. Almost all devices in my home regularly have to reconnect to the wifi, both on the 2.4GHz as on the 5GHz (tested with more than 8 devices). Almost every 15 minutes I see a "wifi channel disconnected" message, 10 seconds later followed by a "wifi connected" message. the Wifianalyser app on my tablet confirms that the wifi signal drops once in a while to zero. I use the latest stable frmware (I read that there is beta firmware but I don't like to loose warranty). The stability seems to unrelated to the amount of traffic on the wifi network.
Will this be fixed in the next firmware of the TP-WDR-4900 ?
View 7 Replies
View Related
Feb 11, 2013
Region : Netherlands
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 121225
ISP : Online
Recently I replaced my Linksys WRT54G for a TP-Link WDR4300. But unfortunately this did not result in an increased speed.On both the 5GHz and 2.4GHz speed is limited to roughly 2.5-3 MByte/s, which is OK for watching movies etc. but I could reach those speeds with the 802.11g router as well!
I'm using the WDR4300 as access point, so I disabled DHCP server and NAT functionality, left the WAN port empty. And I set fixed IP in the subnet range of my modem/router. (horrible Speedtouch device). All works fine and stable, but too slow.
In the wireless settings I tried the 20 and 40MHz bandwith, disabled WMM, tried to lower the transmission power, tried to set a fixed channel. But all those changes do not have a significant influence on the transfer speed. (both on 2.4 and 5GHz) I'm the only 5GHz access point in my neighborhood, so interference cannot be a problem.
The clients indicate a link speed of 300mbps very close to the router, and this drops to indication of 54mbps further away, but effective link speed remains fairly constant (and stable!) (I find it strange that indicated link speed already drops at 3 meters with clear line of sight to the router)
I did the tests with fixed IPs on two laptops and no devices connected on the LAN ports, to rule out problems caused by the modem/router or other clients.The tests were done using a Lenovo x220 and Asus Zenbook, both with Intel dual band 802.11n wifi interfaces. The Lenovo reaches 22MByte/s via the Cisco access point at my work (with less signal as at home).
View 6 Replies
View Related
Dec 6, 2012
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : Not Clear
Firmware Version :
ISP : Verizon DSL
My DSL connection comes into our house in the basement and the DSL modem came with a router included. I bought the WDR4300 for the higher speed wireless connections and the gigabit ports. I really don't need the "router" functionality. I would like to put the WDR4300 on the second floor to give (hopefully) the broadest wireless range. However, I would like all my PCs (including those wirelessly connected) to be on the same sub-net. Is there a way to configure the WDR4300 so it acts like a switch rather than a router?
View 1 Replies
View Related
Apr 26, 2013
Region : Australia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I'm having difficullty configuring a USB hard drive to my WDR3600
The WRD3600 is acting as a switch with my netgear cable modem router as the DHCP server. The DHCP server on the WRD3600 is turned off. the WRD3600 is accessible on my home network and I can connect to attached wifi and Ethernet devices.
when I attach my WD USB hard drive, I can see the device on the WDR3600 web GUI USB settings page. The WD hard drive service status is started and enabled. when I click on the open the disk link, nothing happens. When I try to access the 192.168.x.x/volume1 address, I get a page that says the username or password is incorrect.
When I disconnect the WDR3600 from the rest of my network and turn the DHCP server back on and connect directly to the router, i am able to access the connected usb hard drive.
is it possible to have the WDR3600 acting as a switch with DHCP server off and still access usb devices connected to it?
View 5 Replies
View Related
Feb 27, 2013
Region : Brazil
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
I want to change the antennas on my wdr3600 to increase the range of the signal because my walls are too thick. I can not find TP link brand Dual Band Antennas, so I search ebay and found this:
[url]....
Any dual band RP-SMA antenna is compatible with the WDR3600? or do I need to search for something in particular?
View 1 Replies
View Related
Dec 26, 2012
Region : Others
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I got a new TP-Link TL-WDR4300, connected it to my online pure sine wave UPS like I did with my previous routers with no problem.After about 24 hours, router crashes - no access to web interface, no internet (wired or wireless), must reboot to get it to work again.Router was replaced, same problem with new router.The firmware is the latest one and is customized for Israel because of 5GHz limitations.I was told by the representative in Israel that I should try to connect it to another AC outlet instead of the UPS.
View 7 Replies
View Related
Nov 7, 2012
Region : Denmark
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : Waoo, fiber
i just bought a WDR4300. tried the quick start, then tried to manually set it up like my old Router. but i cant connect to the internet. when i check the status. it often says that WAN is unplugged, no cable. But when i use same cabels and settings on my old router it works fin.
View 2 Replies
View Related
Feb 14, 2013
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : charter, its smarter.
so i have a sb6141 cable modem that is mine and not a lease. it works like a champ when hard wired to my desktop. i just got my hands on a new shiny tp-link wdr4300 yesterday and after messing with it for the better part of 2 hours, something seems to be amiss with the communication between the two. everything will be humming along fine and all of a sudden i get the dreaded PAGE CANNOT BE DISPLAYED. sure as the world i look at the modem and all the lights are off and its resetting itself. and honestly this continues until i pull the power and plug it back up. i think maybe one time in the middle of the night i actually saw it reset itself and then come back online.
View 1 Replies
View Related
Feb 6, 2013
Region : UnitedKingdom
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : v1
ISP : plusnet
I have a WR2543ND router and everyday it drops the wireless connection . all the lights on the router stay on and im still connected to the router but it looses the internet connection . the windows trouble shooter says that it cannot connect to the dns server , I have to reset the router and my computer to get it working again . I Have updated the firmware but still the same
View 10 Replies
View Related
Feb 25, 2013
Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : fullrate.dk
My ISP has provided me a router: Zyxel P-2601HN which has an ideal WLAN transfer rate of 150 mbps. I live in a concrete 2 story house so signals are weak at best on the other floor - therefore, I Have bought the TL-WDR4300 as an extension for the latter floor. I have connected the routers from LAN to LAN and the Zyxel has 192.168.1.1 on LAN and the TL-WDR4300 had 192.168.0.1 as out set. I have changed this to 192.168.1.2 and all the setup (disabled DHCP + other) seems to work alright. BUT i can not log into the TL-WDR4300 !! Not with http://192.168.1.2 and not with [URL]. What I can do to get into the setup of TL-WDR4300. I know I can alays backup the setting and reset the router and load the setting again, make alterations, saving .....but it kind of drastic !Can the two radios SSID names (2,4 MHz and 5 MHz) be the same name as the SSID name on the Zyxel P-2601HN ? What are the implications ?
View 3 Replies
View Related
Jan 6, 2013
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23
ISP : time warner
This is frustrating I owned the router for about 2 weeks. my 2.4ghz is out. Basically I connect to the router on 2.4 can get into the tp-link admin webpage for the router but no internet at all. if I switch to 5 ghz everything works great, or if i use direct connect wire everything is great. I tried disabling NAT but that shut down all my internet connections across all links and manually switching to channel 1 did nothing at all i also tried channel 7. Ideas why only 2.4 ghz is affected out of the blue all of a sudden?
View 12 Replies
View Related
Apr 22, 2013
Region : Australia
Model : TL-WDR4900
Hardware Version : Not Clear
If wdr 7500 will have english firmware ? I bought the router in china and now back home in Australia its all in chinese?
View 6 Replies
View Related
