Create VPN Between Static And Dynamic IP On Netgear FVS318?

Jun 10, 2011

is it possible to to create VPN between static IP and dynamic IP on netgear FVS318?

View 1 Replies


ADVERTISEMENT

Netgear FVS318 Firewall - VPN Not Starting?

Jul 27, 2011

I have Windows Server 2008 R2 set up to allow a vpn connection based on certificate verification. All traffic in my office get routed through a Netgear FVS318 Firewall in which I forwarded all the prerequisite ports to the Server. However, whenever I try to connect from outside the office Windows 7 reports that it either cannot establish a communication with the remote server or that the required Certificate is not installed. I verified the sslcert hash on the Server against the Certificate I installed at home and they match. I can ping both the dyndns and the IP of the office with no problems from home. Or does the firewall not allow vpn connections since it has the ability to host them itself.

View 2 Replies View Related

Linksys Wireless Router :: Connect WRT54GS To Netgear FVS318?

Feb 24, 2012

I would like to connect a WRT54GS to a Netgear FVS318 router to proivde wireless access to my network. My current setup has my DSL modem connected to the FVS318 to provide my network computer with wired internet access. Can I simply connect the WRT54GS to the FVS318 using the LAN port? I've read other threads that mentioned changing the WRT ip address to 192.168.0.150 and disabling DHCP. i've don'e both, but I still don't get wireless access. My wireless devices can connect, but they don't have internet access. I have some questions below:
 
1. In the WRT setup, what do I use for the Internet connection type? Since my Netgear has that information already, do I need to put anything here?
 
2. In Setup -> Advanced Routing, do I neet to change the operating mode to Router?
 
3. Any other configuration changes that I need to do?

View 3 Replies View Related

Cabling / Cards :: Unable To Manually Reset Netgear FVS318 Router

Dec 28, 2011

I have a Netgear ProSafe FVS318 wireless router whose login information I have lost. I have attempted to manually reset it using the reset button on the back, and return it to factory default settings (thus resetting the login information to admin/password).I have checked everywhere, including the documentation for the router itself. I have gotten multiple instructions on how to reset it (generally telling me to hold the button down for anywhere from 10 seconds to 30 seconds until the test light blinks or stays solid and then blinks or stays solid again, or telling me to hold down the button while turning it on). None of these methods have worked. The router still will not reset. It never reboots no matter how long I hold down the button, no matter when I release it, no matter what the orange "test" light is doing, and no matter if I begin with the router on or off. It will not reboot and I still cannot login.

The orange "test" light has behaved the same way each time; after 10 seconds, it turns solid, and then begins blinking before turning back off. After 20 seconds, it turns solid, and then turns off. It does this if I hold the reset button down for 10 seconds, regardless of whether or not I release the button after it first turns solid. If I continue to hold down the reset button, it continues this pattern indefinitely, for as long as the button is held. When I turn the router on, it turns solid before turning off, regardless of whether I am holding the rest button down. Its behavior never deviates from the observed patterns regardless of what I do. At no point has the router ever rebooted on its own.The default login should be admin/password, as this information is included on the bottom of the router, and in its documentation.

View 14 Replies View Related

Dynamic Vs Static IP's?

Jan 29, 2013

Okay so I currently have an ISP that offers the standard "2 Dynamic IP's" and I'm wondering how to utilize this? The tech guy said I need a HUB...but I'm not sure what kind and where to get one etc. Secondly, even if I am able to get this second IP going, will they be entirely separate IP addresses? I need the IP addresses to be completely separate and untraceable to the same source. Is this the case or can you somehow trace back the two dynamic IP's to the same source IP? Will I need two different static IP's if I want the two connections to be entirely separate, unrelated, and untraceable from each other?

View 4 Replies View Related

What If Change Dynamic IP To Static IP

Jan 8, 2011

I have 2 computer connected and both have dynamic IPIf I change one of my computer's IP from dynamic to static Will it be okay to another comp ? ( Can it still connected to Internet / LAN )

View 1 Replies View Related

Can Change From Dynamic Ip To Static

Jan 12, 2013

i need to change from dynamic IP to Static for work, Iv rang my provider talk talk and the only way i can do this is go to a buisness line and pay more a month is there anyway i can log into my router and change from dynamic to static myself? im not on about the IP thats starts 192.blah blah blah its the one where u go somewhere like whatsmyip.com mine is dynamic as it changes if router is reset, there is hiccup in internet or computer is off for the night etc...

View 2 Replies View Related

Wireless :: Change Dynamic WAN IP To Static?

May 20, 2011

I need assistance regarding changing of DYNAMIC WAN IP to desired WAN IP to connect my e-mail server of my office, Problem is :i have a dynamic WAN IP at my home internet router , and my e-mail server at office only allows assigned WAN ips to connect , I want to connect from my home, i know the WAN ips which are allowed to connect my e-mail server and i want to change my dynamic wan ip virutally to desired WAN ip for incoming and outgoing traffic from my wireless router, What I need to do :I need to change my dynamic WAN IP to an static desired ip at my wireless router?

View 4 Replies View Related

Static Or Dynamic IP For Playing Online With PS3?

Feb 11, 2013

Static or Dynamic IP for playing online with the PS3? and there are two PS3's usually playing the same game at the same time in that said house.

View 15 Replies View Related

D-Link DIR-601 :: IP Settings Are Dynamic Not Static

Oct 2, 2010

I have the dir-601 as my main router. Its IP settings are dynamic, not static. My second router, the router I'd like to use as the access point is a Belkin Wireless G Mimo. My goal is to setup the Belkin as an access point downstairs away from the main router. I'd like to do this wirelessly. I'd like to phsycialy plug devices into the Belkin, while the Belkin receives access to the internet wirelessly from my main router, the dir-601.

Here's my issue. There's an easy option to use the Belkin as an access point. So I do this and set the Belkin router to an IP outside the DCHP range ( currently 192.168.0.100 - 192.168.0.199 ) to 192.168.0.250. My dir-601 will only recognize the Belkin access point while plugged in physically. I know this because when I did a ping test it only see's the Belkin when plugged into the dir-601 via ethernet cables. My ultimate goal is to simply set the dlink dir-601 to recognize the Belkin as an access point.

View 7 Replies View Related

Cisco VPN :: ASA 8.4(3) Dynamic VPN And Static Routes?

May 20, 2012

I am running an ASA with 8.4(3) and am trying to setup a dynamic VPN tunnel.  We are having a business reason to establish a VPN tunnel to customers who do not have nailed down IP addresses.  Now I found a number of documents that outline the steps involved.  It seems the basic steps were to Establish a regular tunnelAdd dynamic crypto mapAssign the dynamic crypto map to the tunnel created under step 1. While this sounds pretty straight forward and simple, while prepping for doing just this I hot a road block while thinking it through. In order for my ASA to put anything into the tunnel it has to have a route to the remote network pointing at my VPN peer at the  end of the tunnel.  How do I do this in a dynamic tunnel?  How do I add a dynamic route so the ASA knows which tunnel to stuff the traffic into?  How do I stop the traffic from just being send to the Internet?

View 1 Replies View Related

Cisco VPN :: 5505 - Dynamic IP ASA 8.3(2) To Static IP ASA?

Aug 22, 2011

Trying to connect a 5505 with a dynamic address on 8.3(2) to a static IP'd asa (5510 on  8.2(1) with a DefaultL2LGroup and dynamic maps already created. 
 
Inside networks:
Local (5505)   192.168.100.0 /24
Remote (5510)   10.100.1.0 /24 
 
Configuration on 5505
 
isakmp policy 20 authentication pre-share isakmp policy 20 encryption 3des isakmp policy 20 hash md5 isakmp policy 20 group 2 isakmp policy 20 lifetime 3600 isakmp enable outside access-list 100 extended permit ip 192.168.100.0 255.255.255.0 10.100.1.0 255.255.255.0nat (inside,any) 0 access-list 100tunnel-group DefaultL2LGroup ipsec-attributes   pre-shared-key *****crypto ipsec transform-set myset esp-3des esp-md5-hmac  crypto dynamic-map cisco 1 set transform-set myset crypto map dyn-map 20 ipsec-isakmp dynamic cisco crypto map dyn-map interface outside

View 1 Replies View Related

Cisco VPN :: ASA 5510 - Static To Dynamic Via 4G

Mar 17, 2013

My dynamic ASA is trying to use a Cradle point 4G connection to a head end ASA-5510.  The remote end with the Cradle point 4G is not even initiating the tunnel! I need another set of eyes.  it was initiating the tunnel last week but not completing the connection.  Now its not doing anything.  i am going backwards.  Below is my remote ASA config.
 
ASA5510(config)#  sh run
: Saved
ASA Version 8.2(2)
host name ASA5510
enable password 8Ry2YjIyt7RRXU24 encrypted
password 2KFQnbNIdI.2KYOU encrypted
names
[code]...
 
I have  a laptop directly attached to the inside interface.  The PC and ASA can ping each other. The test interface is the one I am trying to use. Does my default route need to point to 192.168.0.1?  Or is the remote peer correct?  I thought the remote peer was correct? The 4G modem is like a pass-thru device. If I connect my laptop to it I can get out to the internet.

View 3 Replies View Related

Cisco VPN :: L2L VPN Between ASAs 8.4(1) Dynamic To Static?

Feb 8, 2011

I've deployed L2L VPN between ASA's dynamic to static in a hub and spoke format.Everything works great if you are on a spoke ASA and you need to go to the hub but you can not go from the hub to spoke.
 
I'm using ASA code version 8.4(1) ... Below is what I have so far...
 
HUB
 
crypto ipsec ikev1 transform-set ts-dyna esp-aes-256 esp-sha-hmac crypto dynamic-map dm-dyna 65000 set ikev1 transform-set ts-dynacrypto dynamic-map dm-dyna 65000 set reverse-routecrypto map cr-vpn 65000 ipsec-isakmp dynamic dm-dynacrypto map cr-vpn interface outside
crypto ikev1 policy 10 authentication pre-share encryption aes hash sha group 2 lifetime 86400
tunnel-group DefaultL2LGroup ipsec-attributes ikev1 pre-shared-key *****

[code].....
 
Is there any way to apply a crypto map on the Hub side to encrypt the traffic to the spokes?

View 4 Replies View Related

Error - Wrong Static Or Dynamic IP Address?

Mar 23, 2012

Do not have internet connectivity, despite all the lights lit on calbe modem and the ASUS WL520GU router and only the internet and ethernet lights are lit on the Linksys 2102.Despite numerous reboots, no change and even bypassing the router and connecting directly to ATA still no conectivity.When I open a browser, it reverts to the Asus error page, "reason for failed connection: You have set the wrong dynamic or static IP address, though nothing was changed.Funny thing again, a direct internet connection to the ATA did nothing.A google search only just shows lots of unasnered posts on this issue, or only the usual 'please reboot'.

View 9 Replies View Related

Do Internet Cafes Use Static Or Dynamic IP Address

Jun 29, 2012

do internet cafes use static ip or dynamic ip address. Also what would be the benefit if they used a static ip address.

View 1 Replies View Related

Cisco WAN :: Dynamic And Static NAT On 2811 / IOS 15.1 Do Not Work

Mar 17, 2011

I faced up with a strange configuration issue at my 2811 router running IOS C2800NM-ADVIPSERVICESK9-M, Version 15.1(3)T. The configured Dynamic and Static NAT do not work (users can't go out to Internet and can't reach internal services via external IPs).The configuration seems to be very simple (one internal and one external interface, one address for dynamic NAT pool, and only few static translations -- see attached file).

View 8 Replies View Related

Cisco Firewall :: Dynamic PAT And Static NAT ASA 5515

Mar 23, 2013

Recently we migrated our network to ASA 5515, since we had configured nat pool overload on our existing router the users are able to translated their ip's outside. Right now my issue was when I use the existing NAT configured to our router into firewall, it seems that the translation was not successful actually I used Dynamic NAT. When I use the Dynamic PAT(Hide) all users are able to translated to the said public IP's. I know that PAT is Port address translation but when I use static nat for specific server. The Static NAT was not able to translated. Any conflict whit PAT to Static NAT?

View 3 Replies View Related

Cisco Firewall :: ASA 8.4 NAT Static And Dynamic With Same Public IP

Nov 8, 2011

in ASA 8.4, I need to use to static nat an internal IP with a public IP and use the same public IP to dynamic nat another internal IP:
 
-nat (inside,outside) source static IP1_PRIVATE IP_PUBLIC
-nat (inside,outside) source dynamic IP2_PRIVATE IP_PUBLIC
 
All outgoing connection from IP1_PRIVATE and IP2_PRIVATE should be natted to IP_PUBLIC and all incoming connection to IP_PUBLIC should be forwarded to IP1_PRIVATE: is it correct ?

View 3 Replies View Related

Cisco Routers :: Dynamic Ip And Static Dns For RV215W

Mar 7, 2013

I just switched from a Linksys Router to the RV215W, I was able to put custom dns servers for my wan, ie. opendns, but now in cisco, I'm missing this feature.
 
Does any one know how to set-up a workarround with DHCP from my ISP and access custum dns servers..
 
When are we gonna have this feature implemented in the WAN secction.

View 1 Replies View Related

Cisco VPN :: Dynamic From SA520 To ASA5510 With Static IP

Sep 7, 2011

Is it possible to configure a Site to Site VPN from a SA520 with Dynamic IP (DSL) to a Cisco ASA5510 with static IP? I need to make sure about because i am trying to sell this solution to a customer with two branch offices with DSL connection and a Main Office with Metroethernet.
 
I know that using a a pre-share-key on the defaultl2lgroup of the ASA, the ASA will accept any site to site VPN. I have tried this with the ASA 5505  instead of the SA500 for the branch office, but the ASA5505 is too expensive for my customer.

View 2 Replies View Related

Cisco Firewall :: 8.4(2) Static NAT Versus Dynamic NAT

Oct 5, 2011

we are running 8.4(2) on the asa with the below configuration we basically have a static for .7 on .25 and a nat for .7 for port direction with manual nat that takes precedense over auto nat within the object group am I correct that I dontneed the dynamic statement and that its redundant?

-object network obj-10.X.0.25-02host 10.X.0.25
-object network obj-10.X.0.25nat (any,INSIDE) static X.X.X.7 dns
-object network obj-10.X.0.25-01nat (INSIDE,OUTSIDE) static X.X.X.7 service tcp smtp smtp
-object network obj-10.X.0.25-02nat (INSIDE,OUTSIDE) dynamic X.X.X.7

View 1 Replies View Related

Cisco Switching/Routing :: 2560 Create Dynamic VLAN For Specific Group Of Users

Feb 6, 2012

We have Cisco Cat4503 series L3 Switch and Cisco L2 2560 Series Switches, some of the users want to have a dynamic VLAN membership, and connecting with the network as mobile users,
 
can it possible and create dynamic VLAN for specific group of users.

View 6 Replies View Related

Change Cisco Wireless From A Dynamic To Static Settings?

Jun 28, 2012

How do I change my cisco wireless from a dynamic setting to a static settings.

View 1 Replies View Related

Linksys Cable / DSL :: WAG160N - Static IP Translating To Dynamic?

Jun 9, 2012

I have a wireless printer set up with a static IP from below the DHCP restricted range but whenever the printer goes into powersave when awakening I lose connection and ping shows the static IP address being translated to one already allocated in the DHCP range. I can get around this by rebooting the router but its a pain to do this everytime we need to print.
 
192.168.1.52 is this Laptop 
SungStar:/home/john # ifconfig wlan0wlan0     Link encap:Ethernet  HWaddr 00:1F:3C:1C:E3:2F            inet addr:192.168.1.52  Bcast:192.168.1.255  Mask:255.255.255.0          inet6 addr: fe80::21f:3cff:fe1c:e32f/64 Scope:Linkjohn@SungStar:~> ping -c 5 192.168.1.10PING 192.168.1.10 (192.168.1.10) 56(84) bytes of data.From 192.168.1.52 icmp_seq=2 Destination Host UnreachableFrom 192.168.1.52 icmp_seq=3 Destination Host UnreachableFrom 192.168.1.52 icmp_seq=4 Destination Host UnreachableFrom 192.168.1.52 icmp_seq=5 Destination Host Unreachable

View 8 Replies View Related

Cisco VPN :: IPSEC VPN From SRP521 Dynamic IP To ASA5505 Static IP

Jun 18, 2012

I'm having problems configuring an IPSEC VPN between an SRP521 with a dynamic IP and a ASA5505 with a static IP. Static to Static is fine between these devices and I can configure that without problems.  Dynamic to Static however.

View 1 Replies View Related

Cisco Routers :: Combine Dynamic And Static NAT On A SR520?

Feb 3, 2012

I'm trying to combine dynamic and static NAT on a SR520. My dynamic NAT is specified with:ip nat inside source list 1 interface Dialer0 overload access-list 1 permit 192.168.0.0 0.0.7.255 In addition to this I want to perform static NAT for a couple of selected internal hosts. I can do this:ip nat inside source static 192.168.1.5 10.85.10.2 which works fine but means that the source address 192.168.1.5 is translated to 10.85.10.2 for all destination IPs. What I want is for the above static translation only to occur for a particular destination subnet.To accomplish this I have tried:
 
ip nat inside source static 192.168.1.5 10.85.10.2 route-map toOtherSite
route-map toOtherSite permit 10
match ip address 150
access-list 150 permit ip 192.168.1.0 0.0.0.255 192.168.10.0 0.0.0.255
 
But this does not appear to work. Instead it seems to render the host 192.168.1.5 unable to progress through the NAT, whether the destination subnet is 192.168.10.0/24 or not, and I can't work out what I'm doing wrong.

View 2 Replies View Related

Cisco WAN :: 6509 Tunnel From Dynamic IP To Static With Authentication

Jan 16, 2011

I am looking for an option to do the following. [code] Cisco 6509 with SUP2 with MSFC2 full mem
 
I would like the cleanest most stable option to allow this to work and still be secure with authentication. I know on the home side, I can just specify the remote ip and add a password. Not sure what can be done on the DC side to allow this to work properly.

View 3 Replies View Related

Cisco Security :: ASA 5505 8.41 Dynamic NAT / Static Configuration

Apr 17, 2011

I'm having some issues configuring NAT statements on my ASA5505 which has recently been upgraded to 8.41.
 
I have a single dynamic IP on the outside interface of the ASA and would like all internal hosts to NAT/PAT to it. In addition, I would like to have several ports 'forwarded' to internal hosts, one of which is TCP/4343. With the current configuration all hosts are NATing to the external interface properly but the service running on TCP/4343 is not accessible from the outside. See command output below:
 
"sh run object" output:
object network DrJones host 10.81.220.90object network LAN-10.81.220.0 subnet 10.81.220.0 255.255.255.0
"sh run nat" output:
object network DrJones nat (inside,outside) static interface service tcp 4343 4343object network LAN-10.81.220.0 nat (inside,outside) dynamic interface
"sh run access-list" output:
access-list inside_access_in extended permit ip 10.81.220.0 255.255.255.0 anyaccess-list outside_access_in extended permit icmp any any echo-replyaccess-list outside_access_in extended permit tcp any interface outside eq 4343

View 6 Replies View Related

Cisco Firewall :: ASA5510 Dynamic Routing And Static NAT

Dec 10, 2011

I have a ASA5510 with 2 internal interfaces (inside1 and inside2 same security level) configured with OSPF for dynamic routing with 2 routers to corporate subnets. I have a server in a private subnet that needs to be accessed from Internet. So static pat is used in ASA with the command
 
static (inside1, outside) tcp interface www 192.168.1.1 www netmask 255.255.255.255
 
As OSPF is in use, the subnet 192.168.1.0/24 may be reachable from interface inside2. When I tried to configure the static command for inside2,
 
static (inside2, outside) tcp interface www 192.168.1.1 www netmask 255.255.255.255.the error message came out "WARNING: mapped-address conflict with existing static...". Is this just a warning, or this is not possible in ASA.

View 2 Replies View Related

Cisco LAN :: 1841 - Configure Dynamic / Static Nat With Route-Maps

Aug 4, 2009

Basically I have an internet router (1841ISR) with 1 internal (LAN) connection and 2 internet connections. What I want to do is route specific traffic for 3 of my internally hosted services (smtp, https, etc) through one internet connection (fa0/0) and then route all other traffic through the unmanaged/dynamic IP ADSL connection (Dialer 0).

View 9 Replies View Related

Netgear 600 Wouldn't Find Dynamic IP?

Nov 6, 2012

I have Charter Cable and I'm using a netgear n600 dual band router. I set this up at my previous place and am trying to set it up again. I'm not able to get a dynamic ip address from the router. Everything I try to set up the static IP it gives me the message: "to avoid a conflict with your internet service provider your router's ip address has been updated to..." with a different IP address. When I update the static IP, it changes the IP again

View 7 Replies View Related

Cisco WAN :: Simple Static NAT Overlapping Dynamic Internal Range On 5505?

May 21, 2011

I wanted to move to the cisco arena, and having a bugger of a time figuring out simple nat/pat rules combined with access lists. I've been reading Richard Deal's Cisco ASA configuration book, googling the heck out of this simple problem and can't see what I'm missing.
 
I have an ASA 5505 unlimited security plus license running 8.2(3) and a simple network, 192.168.0.x internal, 192.168.3.x dmz (not even touching that yet!) and outside I have a /29 subnet of addresses, 25 is the gateway, and 26-30 are my addresses.
 
I have simple dynamic nat set up on the .26 address to nat to 192.168.0.x. All I'm trying to do is port forward a simple tcp port I set for my linux server (192.168.0.2) on the inside, for arguement's sake, it's 2222 (it's not really). My outside vlan 50 is X.X.X.226 255.255.255.248 , can I make a static nat (inside,outside) x.x.x.226 192.168.0.2 netmask 255.255.255.255 ?
 
I tried using (inside,outside) x.x.x.230 192.168.0.2 netmask 255.255.255.255 and that didn't work either. Is it not possible to use two external addresses to hit the entire /24 range AND a single server?
 
My access rule for this nat is permit tcp any 192.168.0.2 eq 2222 (where I'm using 2222 for my ssh port). then I apply that access list to the access group interface "outside".
 
I thought the outside interface would do a proxy arp (since I do not have the sysopt noproxyarp command) for my 227,228,229, and 230 addresses where .226 is my internal nat for all my internal machines i.e. 192.168.0.1 -> x.x.x.226 . I had this working like a charm before with my fortinet, so I know I have systems listening.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved