Linksys Cable / Dsl :: Cannot Connect Htc Mozrt Via Wifi On Wag160n
Apr 20, 2011
I cannot connect my HTC Mozrt via wifi on WAG160N, all other devices work. I am using Firmware Version:V1.00.16.
My router settings in brief: Security Used : WPA 2mixed Radio Band : Standard Wide Chanel: 11 Standard Channel: 7 (2.442 ghz) All Advanced wireless settings page set to Auto ( apart from CTS Protection)
HTC have advised me that the phones channels are between 7-11 , i have tried those channels and i still get router connection unsucessfull, even with no protection on the wifi.
I have a feeling i have to set a IP to the device , but with the HTC Mozart I cannot do this. IOs there a way i can connect a device to the router with Auto IP adress? i have tried everything! from firmware updrades.. resetting it .. different channels..
I have my ipod touch and HTC Hero connected to the wrouter so inkow there isnt anything wrong with the router, even if it is years old!
View 2 Replies
ADVERTISEMENT
Feb 9, 2011
I replaced my old separate modem and router yesterday for a Linksys WAG160N. Basically , my next door neighbor is paying their ISP a fortune and hardly uses their internet at all. Ive offered for them to share mine (With both of us providing full consent , i'm not doing anything dodgy!) as i have a very big download quota and it would save them some money.
Now the 2 houses are separated by an alley but distance from the router to their computer is about 6m. Strangely , my WAG160N doesn't reach that far as my wireless network doesn't even appear when they in their house on their laptop!So after reading up on wireless bridges / wireless range extenders and all sorts of things i'm now very confused.
Im basically looking for the most cost effective way of extending the signal from my WAG160N , possibly through the use of a second router in my garage) to allow the neighbor to get a good signal. I cannot reposition my modem/router from its current location and also cannot connect a second router using an Ethernet cable , it must be done wireless. So , is there a way i can wireless connect my WAG160N to another wireless router in order to extend my signal for my neighbor to use? I was looking at the Netgear WN2000RPT and the WRT160N as someone else had previous success with using this as a repeater.
View 4 Replies
View Related
Mar 5, 2012
after few years without problem with wifi connection at my home, four month ago began wifi lost connection.
4 iphone with assigned ip address;
3 Portable PC (2 with dhcp and N band, 1 with assigned ip with G band)
Router is not too far from wifi equipment
the wifi is protected with WPA-PSK
Often during day, on pc and iphone we have lost connection, we can see in settting the SSID of my wifi lan, but if we try to connect recive message:Unable to connect to casa(casa is my ssid), on router the wifi led is green fix (not blinking) and only after a few minutes or many try wifi return aviable (for all equipments at the same time and the wifi led blinking)If I want quick connection, without attempt, i simply power off router and after power on, the wifi connection begin aviable!
1. changed SSID, very different from other SSID of my neighbors;
2. changed class of ip address (from 192.168.x.x. to 10.16.x.x);
3. wifi with no protection;
4. tried with & without mac address filter;
5. tried with only 1 wifi connection.
View 3 Replies
View Related
Mar 28, 2012
For a few weeks now, my router has been dropping WiFi connections, seemingly at random. When trying to watch BBC iPlayer is terrible, as it keeps dropping every 5 minutes.
Tonight my iPod Touch (iOS5) was connecting okay, while my son's iPod Touches (iOS3 and iOS4) would not. My MacBook Pro would not connect either.
The only to get things working again, is to turn the router off for a few minutes and turn it on again.
I have router wireless settings as follows:
Network Mode: mixed
Radio Band: Wide - 40MHz channel
Wide Channel: 9
Standard Channel: 7 - 2.442GHz
SSID: Disabled
Router Firmware Version:V2.00.20
My wired connection is running well:
Speed DownSpeed Up
15734.10 Kbps ( 15.4 Mbps )1012.05 Kbps ( 1 Mbps )
View 7 Replies
View Related
Nov 2, 2010
Ive bought recently WAG160n and Ive watched that I have problem with slow speed of WiFi. On LAN cable its ok. Internet provider gives my up 20Mb/sec. download and up to 1Mb/ses. upload. Ive visited
[code]....
I add, that my previous router: WAG200G on this same line gives me 14-16 Mb/sec. download on WiFi. Why upload speed is ok, but download not?
View 9 Replies
View Related
Mar 7, 2011
WAG160N
S/N: SSH00H406302
MAC: 001D7EB42921
Manufactured 04/2008
I can no longer access the internet, and the internet has been difficult to bring up for one to two weeks.Internet light does not come on. Under Status tab, interface is down, tried refresh and connect but nothing.The IP address can be pinged, 4 packets sent and 4 packets received. Tried resetting defaults and refreshing but no success.Bought this router in September 2008 to replace WAG54G which was constantly turning on and off every few seconds.
View 2 Replies
View Related
Aug 10, 2012
I have a WAG160N wireless router that I want to use to repeat a wireless signal that is delivered by our ISP who installed broadband in our cottage, not our house (long story, we live rurally, so I won’t get into it).
So I understand I can simply plug my Linksys to power and that will pick up the signal inside our house (which it does, and we get an excellent strength signal).I further understand that I have to configure the Linksys so it talks to the modem provided by the ISP and which is about 50 metres awayFrom the Cisco website and my own docs I know the first step is to search the IP address online [url].,..
View 3 Replies
View Related
Mar 25, 2011
I can find the network OK but whenever I put in the password it just refreshes and tells me I need a password. My son has just got the applemac for his communication studies and neither of us are very bright with computers let alone apple. They are completely different.
View 1 Replies
View Related
Oct 8, 2009
Model: Linksys WAG160N
Ammex - A
Firmware - 1.00.15
Even after 5 firmware updates I still cant always connect my Iphone with itunes with bonjour service.
View 9 Replies
View Related
Nov 28, 2012
I have a Wag 160n router which works fine with desktop pc connected by ethernet & wirelessly to laptop. My nokia phone finds the wi-fi signal but apple i-phone & ipad dont!
View 0 Replies
View Related
May 4, 2011
Connecting my TP Link 901ND repeater to my cisco WAG160N. Modem router is working well but repeater doesn't seem to be repeating the signal.
View 1 Replies
View Related
May 17, 2012
I'm using Linksys WAG160N - ADSL Modem/Router on one Desktop with Linksys WUSB Adapter. This connection is working fine.Recently I decided to add another Desktop wirelessly to share network, files and internet access. The second desktop is located in another room (approx. dist. is 30 Ft.)The second desktop detects the Modem but it fails to connect and it shows limited or no connectivity.
1. Allow Internet Access to both the desktops without loosing connectivity or without comporomising on speed.
2. Allow file/disk haring of desktop 2 with desktop 1.
View 1 Replies
View Related
Feb 24, 2012
I have a WAG160N wireless gateway . Yesterday when i tried to power it on after a couple of seconds the power led was solid green and the Ethernet leds were blinking with no Ethernet cable attached to the router . The ethernet leds would keep blinking for minutes . I tried to use a screwdriver to do a hardware reset ( with power on ) and i noticed that the power led would start blinking green/red for minutes . I tried to use another wired router which i have for backup and it could connect to the internet normally without a problem.
What the green / red blinking power led means ( power led is green and then changes to red and then it starts over ) ?
View 1 Replies
View Related
Mar 30, 2009
Is it possible to "tweak" the SNR on the WAG160n?
View 4 Replies
View Related
Dec 20, 2011
I've just been sent a new ADSL modem router by my new broadband supplier and plan on using it. However, my question is, can use my old wag160n to replace one of these, which im currently using to connect an old xbox to my wireless network, but also make use of the other lan ports on the wag (i.e. Connect more than one non wireless device to the wag and gain access to my wifi network?)
View 1 Replies
View Related
Jan 21, 2013
I've a 20Mbit/s connection with Telecom Italia provider.My line values follows:-- DSL Information ---DSL Driver Version: AnnexA version - A2pB023k.d21dDSL VPI/VCI: 8/35DSL Status: ShowtimeDSL Mode: ADSL2+DSL Channel:DSL Upstream Rate: 979 KbpsDSL Downstream Rate: 22105 Kbps Down upDSL Noise Margin: 12.0 dB 13.4 dBDSL Attenuation: 10.5 dB 4.3 dBDSL Transmit Power: 14.0 dBm 12.4 dBm?I have issues about connection stability : on HEAVY load download the PPP connection goes down. The sync signal stays up, but the PPP goes down!
In the log these lines corresponds:
Sun, 2013-01-20 23:29:29 - No response to 3 echo-requests
Sun, 2013-01-20 23:29:29 - Serial link appears to be disconnected.
Sun, 2013-01-20 23:29:29 - Enter: tdb_store.
Sun, 2013-01-20 23:29:29 - tdb_store: calling tdb_update.
Sun, 2013-01-20 23:29:29 - Enter: tdb_update.
[code]....
My ISP says that there are no troubles with the line and it can be an issue of the modem...
View 8 Replies
View Related
Jan 2, 2012
When I enable the debug with ?todo=debug shall I see more info in the logs ?How to stop the debugging ?How to print the logs ?What is the difference with debug and ppp_debug ?What is the effect of the sendlog command ? I didn't receive any email with a log !
View 3 Replies
View Related
Nov 20, 2011
When i connect my WAG160N V2 to DSL, i don't get link, but if i tried whit a friend´s modem i get link. I use the same cables and dsl split.
View 1 Replies
View Related
Aug 16, 2012
Struggling to enable Airplay using a WAG160N. Any settings I need on the router? Looking on forums, came across suggestion to disable WMM support. This seemed to work and i had Airplay but now I've lost it again.
View 1 Replies
View Related
Aug 30, 2012
I hard reset the router WAG160N and i can't access it on 192.168.1.1, i can connect to the wireless connection but it shows unindentified network, in properties gateway IP is absent. i also get 169.254.1.38 as IPv4.What could have happened to the modem, I can't use it at all at the moment?
View 3 Replies
View Related
Feb 21, 2011
Two years ago I bought a WAG160N for modem (ADSL) and router functionality. I consider to buy a pure router (E3000 or E4200) to connect to the WAG160N and use that one purely as the modem. How and what should I configure/disable on my WAG160N?
View 3 Replies
View Related
Dec 22, 2008
Why can I not register a WAG160N router with Linksys? Is this because these devices are not sold in the US?
View 4 Replies
View Related
Jun 16, 2012
Some years ago i have buyed a WAG160N i haven't never used, because once i plug it power, it start to reboot and reboot in a loop...Is there something to do with it or should i put it in the trash ? Firmware using is probably Ver.1.00.15?
View 6 Replies
View Related
Feb 4, 2011
I have a WAG160 setup to use the one fo the LAN ports as a WAN connection. The issue is every now and again the internet connection drops and it seems it is unable to communicate with the DNS server that is providing the internet connection.
View 9 Replies
View Related
Jan 25, 2011
Any hardware that can re-boot a DSL router such as the WAG 160N when the router no longer passes traffic ? Today, while the DSL line and the Internet appeared to be working, I could not log in to the router from a LAN machine and I had to power it off and on again by hand.We have a number of surveillance cams on the LAN and this must not happen, that the cams cannot be accessed, in particular if nobody is on site for a few days.Unfortunately, the WAG 160N does not have a daily re-boot option. What can one do except for installing a timer that switches the power to the router off and and on again ?
View 5 Replies
View Related
Nov 30, 2011
I'v just changed my internet provider. That new one uses Annex b, my wag160n is purposed to annex a. Thats what i'v done. Turn on bridge mode turn off dhcp, set PPPoE with my login and password. And here is my problem. I cant connect by wifi with more then 1 device. I can only connect with my laptop when i'm trying to connect on my xbox it says it cannot get ip adress from router. What shoudl i change ?
View 6 Replies
View Related
Apr 19, 2013
i trried te update the firmware of my WAG160N. I had to choose between two versions. I tried both. But both versions give the message that is the wrong version and the installations stops.
View 9 Replies
View Related
May 24, 2011
I purchased a new WAG160N router a few months ago and recently I have been having major problems with connectivity.The problem is that it resets itself at seemingly random times. I see it happening. The red power light starts flashing red and then the other lights slowly turn green as it re-establishes connection to the internet.
This is becoming extremley frustrating as I do online gaming with my XBOX 360.I use wired connections using ethernet cables. One to my laptop. And one to my XBOX 360.I have contacted my ISP who have done line checks and I have had an engineer look at my line and all is good. I have also replaced all cables to/from the router including phone cords and ethernet cords. EVERYTHING is new.I recall one incident in which my internet was down and I just couldnt get connection AT ALL. I rang my ISP and they got me to log into my modem settings. The settings were all altered for some reason and I have no idea why. When they told me to enter the details in the settings the internet worked immediatley.
View 3 Replies
View Related
Dec 11, 2010
I have a wag160n and would like to disable the wireless and use as a wired ASDL modem. I can't see any obvious settings I'm the setup or buttons on the unit but was wondering if I were to set the DHCP to disable if
View 4 Replies
View Related
Jan 7, 2012
My Linksys WAG160N has worked fine for 2 years however all of a sudden when I power it up it's start normal but after 4 seconds all ethernet lights blink one time and all start from the beginning, it's like it reboot every four seconds.It happens so quick I can't even get to the Internet/Network Settings in WIndows Control Panel.I have tried accessing router setup and installing firmware and both have failed - it can not find the network address.If I try to reset with the reset button on the rear (30sec reset), it stops rebooting and the power LED starts to blink red/green and the ethernet LED of the port where my cable is connected starts to blink alsoI have set IP address manually on my computer as per the Cisco support pages (192.168.1.1), still no response from ping.I have also tried to reinstall firmware using TFTP but it also fails because it can not find the network address.
View 9 Replies
View Related
Mar 24, 2011
I need to replace a failing AG241v2 and I am going to use a WAG160N.I problem is I notice there are two versions of WAG160N, v1 has a RJ45 port for the DSL and v2 a RJ11 port.AG241v2 has a RJ45 so the cable I was using was a Ethernet cable.Now this cable doesn't fit, of course it is bigger, I tried with a RJ11 cable but DSL light doesn't show up, it looks like it is not receiving any signal.Is there any adaptor or any cable to use WAG160Nv2 or should I replace it with a WAG160v1?
I found in several web stores when they talk about WAG160Nv1 they use the code WAG160N-E1 and for the WAG160N-v2 they use the code WAG160N-EW. Can they make it more difficult??
View 1 Replies
View Related
Apr 15, 2012
I am trying to lower the transmission power on my WAG160N. I thought it should be an option in my advanced wireless settings of the web based setup page, however there is only transmission rate, n transmission rate and cts protection mode.
View 1 Replies
View Related
Jun 27, 2011
I buy WAG160n wireless-n adsl2+modem router with wire it works but it not connect without wire and i cant connect internet through my pc.
View 1 Replies
View Related
