Cisco Firewall :: 515E With Software 8.0(4)28 Connects Inside And Outside Networks
Sep 9, 2011
A pix 515E with software 8.0(4)28 connects the inside and outside networks. There are some servers in "outside" that have addresses overlapping with the internal subnets (192.168.10.25 and 192.168.10.26), and those servers have a reverse route only to a specific subnet (172.16.5.0/24). [code) Now to the problem. 192.168.10.26 is an HTTP server. On the pages it has hyperlinks pointing to http://192.168.10.25, the browser tries to access that server and, surely, fails, as the target server is only available by sending requests to 172.19.100.1, with the packets being DNAT'ed.Is it possible to rewrite the packet's body, replacing all occurances of url... I know it's a kludge, but other options are even worse.ASA eith 8.4 software? IOS router?
I' d like to have some support for a very-basic PIX firewall configuration. I 'm dealing with PIX 515E. Inside hosts can ping inside interface , outside hosts outside interface and so on. Simply i cannot ping outside interface from inside hosts, Inside host-192.168.1.0
Outside - any host like google.com, or to check my isp link's dns ip. I have attached the pix configuration text file to test.
I have a PIX 515e running version 7.2(4).I have 2 interfaces - DMZ3 (sec lvl 50) and LAB (sec lvl 100) behind the pix. There is also the OUTSIDE interface (sec lvl 0) which connects to the internet.In DMZ3 I have a webserver - x.x.124.217/24 (host is NATed via static command to public IP)In LAB I have a server - x.x.1.203/24 (entire range is NATed via NAT/Global statements to public IP)The server in LAB needs to access a webserver in DMZ3. From the internet both of these hosts have public addresses that are NATed into the inside addresses. I can reach the webserver from the internet, but not from the LAB interface.I think I have to add a static command so that the LAB host can access the DMZ3 host without accessing the internet.
I have a PIX 515E V7.0.4 and I'm having trouble with http access between the inside interface and a DMZ zone I have. I have a web server setup in the DMZ with an web interface to upload/download files. I can connect to this interface from a workstation in the inside network but when I try to download a file it is incredibly slow. If I upload a file there are no speed issues. If I connect using an https connection then both upload and downloads are at speeds I would expect.
I have disabled http inspect but this didn't improve the speed connection.
Other http communications from inside to outside do not have any speed issues in either direction.
I have a PIX 515E that I want to use to as a border between my internet connection and my Cisco AIR1131AG. I have configured the PIX to have the outside interface as a dhcp client which gets its dynamic IP address from the cable modem. the AP is connected to the E1 inside interface. Now I could see the E1 interface from the arp table from the AP but I cannot ping it. From the firewall I don't see the ARP table from the firewall. and i cannot ping the AP. what is wrong with the configuration? side note, i am able to connect to the AIR1131AG from my laptop I was not able to retrieve an IP address.
FW1 - CONFIGURATION
interface Ethernet0 description uplink towards the techsavvy modem speed 100 nameif outside security-level 0 ip address dhcp setroute !interface Ethernet1 description >>> WIFI LAN ACCESS <<< nameif inside security-level 100 ip address 10.0.0.1 255.255.255.0
I just installed a new ASA 5505 for an office with three internal subnets. The three networks can each get online fine and ping eachother, but cannot browse to shares on the two internal networks other than their own. How do I configure the ASA to allow all traffic between these three inside networks?
I have easy vpn on my PIX 515e and working normally everywhere, except when my users go FRANCE, the vpn client connect, but, can't ping or access any inside network resources. when same user try any where here in EGYPT, it works normally.
About a week ago my laptop stopped connecting to the internet for no apparent reason as it had connected just fine the night before. It's a Toshiba and the wireless router I use is a belkin. Every other wireless device from my brother's laptop to my Ipod can connect to the internet just fine. Even the PC connected to the router via ethernet cable can get online. I've tried unplugging the modem, resetting my IP address, directly connecting with an ethernet cable to the router, and resetting my router. My internet browser, IE, used to freeze up but I had a friend look at and he only managed to have it unfreeze[CODE]
I have a simple isp topology built in GNS3, for testing (pppoe) dialers:cisco router(R1) connected to my pc network card, doing NAT translations for all the devices in the topology.I know how to configure NAT for spesific ip range, but i can't find out how to configure NAT for networks which are learned through ospf (or any other dynamic way).
I have an Pix 515E firewall with Pix724-33.bin IOS. I just want to know that does this IOS support SNMPV3 or I will have to upgarde it with some other version.
Ive got a problem with passing traffic through a Cisco 515e firewall.im trying to telnet to devices on the inside net, 172.16.x.x fom an outside net 10.x.x.x? ive configured a group called infrastructure and added the 10.x.x.x addresses.ive configured acl 101 inbound on the outside interface:
access-list 101 permit tcp object-group INFRASTRUCTURE any eq telnet
when i try and connect, using a packet capture I can see traffic from 10.4.4.34 to the inside device 172.x.x.x on the inside interface but i cant see the traffic leave the outside interface ive used the same group infrastructure group before to connect to VM machines on the 172.x.x.x net on RDP and this wrks ok. access-list 101 permit tcp object-group INFRASTRUCTURE object-group VMs eq 3389
I am trying to set the PIX firewall to transparent mode.After I set it to transparent firewall, I allowed all icmp, tcp, udp traffics.Currently, any devices in the inside network can get the ip automatically from DHCP server in the outside network but cannot ping to any servers in the outside network either access the internet.Do I need additional confiration on the firewall?
Here's the configuration:
PIX Version 7.0(1) firewall transparent names ! interface Ethernet0 [Code]....
I have a PIX 515 Ewhich does authentication for SSH via RADIUS protocol and fails over to the local database if radius server goes offline. But when the radius server comes back online, authentication still takes place through LOCAL and not the radius server. Following are the commands:
\I just configure my PIX 515E with version 7.0(4) and having problems to get traffic out on eth0 (if name outside). There is no problems between different VLAN ,all VLANs are configure on eth1. It is also possible to accass services on VLAN 10 (DMZ) from outside. The only thing I see in syslog is "Built Outbound" and "Teardown".
I have a Pix 515E running PixOS version 8.0.4 with two interfaces, inside and outside.On the inside interface, I have a Redhat Enterprise Linux 5.4 64 bits machine as an NFS server version 4 (NFSv4).On the outside interface, I have three (3) Redhat Enterprise Linux 5.4 64 bits as NFS clients.I am looking for the exact UDP and TCP ports to be added to the ACL in order to accomplish
I need ot upgrade a Cisco PIX 515 E to A Cisco ASA (not sure what type and modle yet!). the PIX currently has about 80 lines of ACLs and no VPNs. So only inside and outside interfaces and 80 lines of ACLs to be transferred over to the ASA.I was wondering if the ACLs can be transferred over to ASA as is?is there anything that I need ot watch for?
I have an issue in the Cisco PIx 515e series. The IOS is 6.1(2).I have set sepecific access-list to allow incoming traffic to inside interface. But still the TCP 3-way handshaking is dropped here. [code]
We just switched over from a T1 line to 50/4 Mbps cable Internet. The speed was fine with the T1, but when we switched over to cable, the download speeds didn't increase. I'm getting 2-3 Mbps up and still only 1.5 Mbps down. I inherited this network a few years ago, so I didn't configure the Pix initially but I have been managing it and can't find a setting limiting the bandwidth for the liffe of me. I know it's not the Internet because when I connect a computer straight to the modem, the speed is great. As soon as I put it through the Pix though, it slows way down.
I'm trying to use port redirection to allow outside access to a internal web server. As far as I can see, everything is configured properly. The Open Port Checker tool from yougotsingle.com says that the port (80) is open. However when I goto access it the connection times out. The external address is static from my ISP, and I will call it xxx.xxx.xxx.xxx. The server is at 10.1.1.20, and is functioning properly over the LAN.
I have Cisco PIX 515E for my Lab and can't recover the password. It is not connected to the network. I have configured server, address, gateway from the monitor mode and tftp not seeing my laptop. best way to reset or recover password.
I've been struggling to get ASDM (PDM) installed and running on my PIX 515e. The PIX IOS version is 7.2.4(30) The ASDM version I've copied to flash is 524.
I've followed the Cisco documentation verbatim, however I still cannot connect via the Java ASDM client or via http. When I try to connect via http, my PIX shows the following error: "tcp access denied by acl from..." I do not this this is a security (ACL) issue as I've tested after opening everything up and still no luck.
Here's my running config (w/ the relevant statements prepended with ">>>"):
I have the following Pix 515E Firewall, that has been working good for a few years. But suddenly, the Pix stop booting up. The only thing that is happening is the power and network traffic led flashes and the active led is off. So my question is that is this symptom a hardware or software problem and is it fixable with either new parts; or is my firewall dead. I suspect that it is a hardware problem since the active led doesn't light up. I cann't even enter the ROM Moniter mode.
I am facing high CPU util on my pix 515 E which is in failover mode.During peak hours the util is see rising to 60% where as in off peak hours it is normally12%.
During normal operation the average utilisation was observed to be 30% but suddenly from 2/3 days it is constantly 60% doule the value as earlier. Have gone through the logs and traffic but not able to tarce anything particular
below is the o/p of some command taken for analysis
IOS version 8.0(4) sh cpu usage CPU utilization for 5 seconds = 51%; 1 minute: 61%; 5 minutes: 58% sh cpu usage
I need to create a DMZ zone in my network. One server need to be put in DMZ. I have a PIX 515E 6.3.3. It has free port to create DMZ.
1) Put a new switch for DMZ zone 2) Connect it to the DMZ port 3) Create a NAT for inside to DMZ with same IP as inside 4) Create ACL for permiting traffic to DMZ and apply it to outside interface 5) Create ACl for permitting traffic from DMZ to inside 6) Routing for DMZ in PIX
I was wondering if I picked up a used (End of Life) pix-515e, would would I need to do to be able to upgrade it to that latest version of IOS made for that product? Is it still possible to even get access to that version? Will cisco allow downloads for that devices IOS?
I´ve a problem with my "old" PIX515e device. I wanted to flash this device to a new firmware level but forgot to disable the "lost enable" password before. So I started to make the firmware upgrade on my device, ended up with "flashfs" is busy and I should start the enabled modus and "copy flash tftp" to activate the new flash version. Unfortunalty I cannot do this because I´ve lost my password. When I´m trying to boot this device up now, it will end with a error message...
Unable to locate boot image configuration Booting first image in flash No bootable image in flash. Please download an image from a network server in the monitor mode Failed to find an image to boot
As mentioned, when I will load a new flash image over monitor mode, i cannot activate that image because of flashfs is busy.The password reset bin files will not work too. I tried that too but this one will recongnize no active installed flash.Is there any way to reanimate my PIX515e? In newer devices there are possibilites to work with changing config register but I´ve found nothing about that for a PIX515e.
