When i install my ASA5505 i get the following message? "This platform has a Base license.
Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Boot microcode : CNlite-MC-Boot-Cisco-1.2
SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.05
i2c_write_byte_w_suspend() error, slot = 0x0, device = 0x40, address = 26 byte
count = 1. Reason: I2C_UNPOPULATED_ERROR"
I recently acquired a used ASA 5505 and have encountered issues with getting the PoE output on Ports 6 & 7 working. Theese two PoE ports are behaving like all the other ports (100mbit, Vlan 1). Per the best I could Google, I made sure the all relevant ports are set to "auto" for duplex and link speed. Again, the ports do work for data - just not PoE. The LEDs light up ok.
I've tested four different working devices that can be powered off PoE with it, and all failed to power up using a straight-thru Ethernet cable connected to ports 6 & 7.
Ubiquiti PicoStation M2
MikroTik OmniTik
MikroTik RB450G
MikroTik RB433
What should I do to get PoE working? Is it a defective unit?
: Saved
: Written by enable_15 at 18:56:43.926 CDT Sun Jun 3 2012
!
ASA Version 8.4(4)
[Code].....
i'm trying to setup my 5505 for SSH but it seem doesn't work. console and HTTPS/ASDM are working.
my teraterm is just stuck with the user/password screen. also tried using putty but still failed.
ciscoasa# exit
Logoff
Username: admin
[Code].....
i have 2 internal server sitting in inside interface
inside network vlan 1 ip address 192.168.0.20, and 192.168.0.22
i going to map 192.168.0.20 to public ip routable address 203.117.124.180 and 192.168.0.22 to public ip routable address 203.117.124.181
the purpose is to make those 2 server 192.168.0.20, and .22 to be able to access remotely using public routable ip address,
however, after done the configuration i still not able to ping or access the public IP Address mention above. my both server are turn on and can access internally.both server are also able to access internet. See below partial configuration retrieve from Show Run.
nat-control
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
nat (Antlab) 1 0.0.0.0 0.0.0.0
[Code].....
I'm trying to get a new 5505 installed in our network to replace the 1841 that died over the past few days (memory issues). One of the big pieces of functionality that the old router gave us was the ability to open certain ports to the outside world to let clients see web sites we were working on for them or let employees RDP in to their work machines. I'm having trouble getting that working properly with the new device.
After a lot of trial and error, I finally got some ports working, but only for some IP addresses. In theory, Comcast (our ISP) is routing 13 IP addresses to our device (a.b.c.177 through 189). For historical reasons, the external IP of the device is .178. Only those NAT entries for .177, .178 and .179 are currently working. I've attached the configuration of the ASA, as well as the configuration of the old 1841. As far as I know, Comcast's equipment is doing its job, so I don't have a lot of reason to question that end of it. And it was working with the 1841 in place before its untimely demise.
One note - I am also having trouble getting the VPNs working, so they are a work in progress. That will account for some of the differences in the configs.
there is an issue with tracroute from ASA 5505 with 9.0(2) - here is the running configuration [code] with this running configuration - from the LAN tracerouet to public IP, it is working fine. but once I traceroute from the LAN 192.168.225.x to the corporate networks via the IPSec l2l tunnel - it does not show any hop at all - even the inside interface of the ASA does not show in the traceroute.
View 4 Replies View RelatedI am trying to set up a SLA statement on an ASA 5505 version 8.2(5). When I enter the command "sla monitor schedule 1 life forever start-time now" I get a message stating "%Entry not configured."
View 1 Replies View RelatedI have an ASA 5505 running 8.4(3) at home and I'm banging my head against the wall trying to get the PCTV working from my local ISP.Basically I open a web page for the service and I can stream all the basic TV channels to my PC screen.
I just simply cant get this working through the ASA.. I know absolutely nothing about voice/video in networking.
My setup regarding ASA configurations are as follows
interface Vlan1
description LAN
nameif LAN
security-level 100
ip address 10.0.0.1 255.255.255.0
igmp forward interface WAN
[code....
I can get the PCTV working if i bypass the ASA. I can for example get the PCTV working on PC2 if I simply change the port Ethernet0/2 to access vlan 10. So theres just simply something that I havent configured on the ASA or the ASA doesnt support something?I took a capture from my PC2 just as I opened the browser and connected to the PCTV url (opens our local channe 1 right away)Only thing I can see in the capture at that point is:
- V2 Membership report / Join group 232.1.3.1
- Right after a remote host from the ISP networks starts sending the stream with the destination port udp/2000 with the destination address of 232.1.3.1
what I could check in my configuration? Or is there something that I have simply configured wrong already on the partial configuration shown above?
I have a base 5505 and would like to get AnyConnect working. To do that, would I have to first purchase either an essentials or premium license and then purchase the AnyConnect Mobile license?
View 1 Replies View RelatedI configured a VPN on my ASA5505 and it seems to be working just fine if I connect with my i Pad or iPhone. But if I use the Cisco VPN Client, I can authenticate but can't get to any other the server that I can access just fine from my i Pad.
I can RDP from my i Pad to servers but I can't RDP from my laptop to the same servers.
I have setup a ASA and everything but ipsec seems to be working. I was able to use the clientless ssl but I need ipsec working. I'm at a loss. config is a little sloppy and i will be cleaning it up but would like to get this working first.
Cisco Systems VPN Client Version 5.0.07.0290
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
[Code].....
I was installing a IIS server to our client and created access - rules for http server and port translations. After that i noticed i lost local lan access trough vpn. Anyconnect and ipsec vpn. No other changes made to asa than those access-rules and nat changes. I'm trying to find out what is wrong, vpn connects okay, i can ping ASA but nothing else on inside network (for example dns server). Dns is not either working. When i ping local server, i can see in log.
View 8 Replies View RelatedHow I can actively monitor the interfaces and overall status of 2 x ASA 5500s in an Active/Standby configuration?
I can setup monitoring of the interfaces on the Active member but I'm not sure how to manage the Standby member?
We were having a discussion of ios firewall vs. asa for smaller clients(less than 50). On using ios firewall(zbf or cbac)and an asa 5505/5510. One of the arguments brought up on using ios firewall on the router is that a router will do an ip sla failover. I have configured a number of isr's for this and i know it works good.
View 1 Replies View RelatedI have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?
View 1 Replies View Relatedsetting up an ASA 5505 to be used as a firewall between a BT internet router(BTNet service) and a Cisco 3560 Lan switch. BT have presented me with a cisco 3800 series router with the following details:
Network Address Network Mask BTnet NTE Router LAN Address
There are 2 Gigethernet ports on the back of the router port Ge0/0 is connected to the BT NTE and the status light is flashing green. Int ge0/1 is connected into port int e0/1 of the ASA but i am unable to get any connection.
I'd like to see some REAL LIFE comparisons of ASA firewall throughput (a bit like this one for ISR G2 Routers - [URL].
The reason I ask is that I recently upgraded a firewall from an ASA5505 to an ASA5520 on a small network where the only outside connectivity was a single 10meg Internet circuit with an IPSEC VPN (not landed on the firewall but on a router) to another site.
When I swapped out the firewall the users noticed a big improvement. The firewall is not doing anything out of the ordinary - no IPS or VPN, just standard state full inspection.
I was logged into our ASA 5505 via ASDM-IDM Launcher (everything was working) and when I tried to update a change later on today it was unable to send the request. I tried to ping the device and the request timed out. The internet is still working, the VPN connections are still up. But I cannot connect into it anymore.
View 4 Replies View RelatedWe're trying to get a new ASA 5505 put in place on our network after the untimely demise of our 1841 router. One of the functions of the router that we need to get back up and running is a pair of VPNs to employees that we have working from offsite. These are site-to-site VPNs.
They worked with the 1841 in place, so I know that the other end works. I'm just having trouble configuring the ASA to match. I've been through the wizard in ASDM a couple of times, but have yet to have any luck getting it to connect.
Attached are config files for the 1841 (with both VPNs) and the 5505 (with only 1 VPN in place). What I may be missing in order to get this working?
One note - I am having some trouble with my NAT configurations (another post pending), but I think they are close enough that I hope it's not interfering with the VPNs.
If I can get one running, the other has a nearly identical set up, so I should be able to get the second pretty easily.
Trying to set up a asa 5505 in transparent firewall mode. I cannot set the management ip address:
ciscoasa> enable
Password:
ciscoasa# config term
[Code].....
I have been working with ASA 5510,20,40,80 but not with 5505 this vlan and its interfaces are quite confusing.Just want to know how it works and its connectivity to Cisco Switch.Do i have to put the interface of the switch in the same vlan as i am creating the interface vlan in firewall ?Now the switch port connecting to this Eth1 interface should also be in the same vlan ? i.e vlan3 ?? or it will be in trunk ? The default configuration shows the eth0 with no access vlan and interface eth1 with access vlan 2... does it mean the eth0 is in vlan1 ? (Nativ Vlan ) ???
View 4 Replies View RelatedI have a cisco asa 5505 firewall. Is it possible to block secure websites in it like [URL]? I have already tried regular expression filtering but it filters only http traffic.
View 4 Replies View RelatedI am trying to configure our ASA 5505 so that our users can access our ftp site using [URL] while inside the firewall. Our ftp site is setup so that you can reach it by either browsing to the above url or by browsing to ftp://99.23.119.78 but we are unable to access our ftp site from either route while inside the firewall. We can access our ftp site using the internal ip address of 192.168.1.3.
Here is our current confguration:
Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasaenable password qVQaNBP31RadYDLM encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0 !interface Vlan2nameif ATTsecurity-level 0pppoe client vpdn group ATTip address pppoe setroute !interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!ftp mode passiveobject-group service DM_INLINE_TCP_1 tcpport-object eq ftpport-object eq ftp-dataport-object eq wwwaccess-list ATT_access_in extended permit tcp any host 99.23.119.78 object-group DM_INLINE_TCP_1 access-list ATT_access_in extended permit tcp any interface ATT eq ftp access-list ATT_access_in extended permit tcp any interface ATT eq ftp-data access-list ATT_access_in extended permit tcp any interface ATT eq www access-list 100 extended permit tcp any interface ATT eq ftp
[code]....
New to the ASA 5505 8.4 software version, but here is what I'm trying to do:
-Single static public IP: 16.2.3.4
-Need to PAT several ports to three separate servers behind firewall
-One server houses email, pptp server, ftp server and web services: 10.1.20.91
-One server houses drac management (port 445): 10.1.20.92
-One server is the IP phone server using a range of ports: 10.1.20.156
Basically, need to PAT the ports associated with each server to the respective servers behind the ASA 5505. Is anything missing from this config? Do I need to include a global policy for PPTP and SMTP? [code]
I'm integrating a Cisco ASA5505 with a Websense proxy. I have a configuration setup where we have four routers which are used for Internet access. There are two VLAN's - Guest and Private. What I would like to achieve is making the use of available bandwidth by load distribution via GLBP, and filtering users web traffic. Two routers will be used for a GLBP group in one VLAN, and the other two routers will be used for GLBP in another VLAN.The users are connected to a Cisco 2960 switch and are in their respective VLAN's. I'm planning a 802.1q trunk to a Cisco ASA from the 2960 switch, carrying both VLAN's.What I would like to know is if there is a CSC module (or similar) which has Websense installed on it, and if it is possible to setup the ASA5505 in transparent mode to filter the traffic in this way? Hopefully this would allow multiple users to take advantage of the additional bandwidth, and not be restricted by using a traditional proxy setup which where all web traffic would be originating from a single MAC address.
View 1 Replies View RelatedI have an issue with my firewall,each time i configured a trunk port in the firewall and connect a sw 2960S with a trunk port also, all the interfaces in the Firewall go down ( virutal intertaces, inside, outside , dmz) , also another switch 3750 that is connected to another port in the firewall( access port only) it start to a new negotiation of spanning tree.What could be causing this problem? the firewall didnt sedn bdpdu i think the IOS of the firewall its a 8.2
View 3 Replies View Relatedwe are planning on connecting a new aquired company to ours soon?We will connect the remote site to the HQ via a D3. I've been told we will need to have a firewall between them and us for a time. I was thinking of terminating the D3 connection at the remote site of 80 users. Can I use the asr as a firewall as well, to protect the HQ from the Remote site - or should I use a seperate appliance?I was thinking of a asa5505 but, am concerned with bandwidth limitations of the box?
View 1 Replies View RelatedI want to configure an ASA 5505 in transparent mode (7.x). Somehow, I got it to work.. but i need some kind of step by step description. I just want to connect it with outside on a route .. inside in my LAN. Its working now with one ASA. But in the Web Interface the Interfaces inside and outside are down.. but its working.
View 5 Replies View RelatedWhen I upgrade the ios on switches, I just create int vlan1 assign it an ip and subnet, then tftp to my pc that is plugged into the switchport using the download-sw command.
I am not sure how to do this on the asa. Do I just plug my pc into port 0 which the documentation says is mapped to vlan 1 with and ip of 192.168.1.1? I tried this by making my pc's ip 192.168.1.2 but am unable to ping the asa. Do I have to change the security level or anything?
I’ve been using a Cisco ASA 5505 Security Plus bundle for two years now without any problems. My previous Internet Service Provider was routing the external IP I was leasing directly through to my internal network without NAT which my ASA 5505 was working well with. Thus, I had configured my 5505 to provide NAT to my inside network which includes two subnets one for my workstations and internal "private" resources and a DMZ to provide access to my webserver, email server and two domain name servers; but restrict access to my internal; resources. i recently changed my ISP to Verizon FiOS (which is providing me with 25 Mb bandwidth at a fraction of the cost of my old T1) which is set up to provide 5 Static externally facing IP numbers for my email, webserver and name servers;. The problem is the Verizon router doesn’t support my use of the ASA Appliance (at least not the way it is currently configured. Verizon recommend I purchase a business class router and use it in place of the one they provided with my installation. With this in mind, I bought a Cisco RVS4000. I have configured it to use the primary external IP number and have internet access; however, the new router is providing NAT addressing which the ASA is in conflict with (they are both using the same NAT IP range). I'm assuming the ASA 5505 is expecting to have access to the external IP addressed (since that is what it was getting before) and NOT NAT address. How to configure the new router to either provide access to the five static external “real world” IP to my Cisco ASA Firewall. However, I just need to get my ASA 5505 back in the loop and would prefer to do this rather than go back to the Verizon router combined with a low end firewall. So, my questions are: Does the ASA 5505 expect real world External IP numbers? Or can it work with NAT addresses being fed to it from the router? And, if so, how do I configure the access rules and other items which are currently mapping to external numbers?
View 27 Replies View RelatedI am configuring a Cisco ASA 5505 firewall.In the office there is 1 x SBS 2008 server and 5 x PCs, all sat behind a Netgear DGN1000 ADSL router.We want to implement a ASA 5505 for added security.I have configured the internal interface of the Cisco ASA 5505 to be 192.168.0.1 - this is connected to local switch. The client PCs use 192.168.0.1 as their default gateway.I have configured the external ASA 5505 interface to be x.x.x.217. [code]Change the current router status from Router/Firewall/Modem to Modem only (Bridge mode). The ASA 5505 has its outside interface connected into one of the LAN ports of the netgear. The lan port has an IP of 192.168.0.254.
View 3 Replies View Relatedwhen i am booting ASA firewall i am getting the following error.
<0>Kernel panic - not syncing: Attempted to kill init! and it stops and will not work. check below the whole log file
how can i solve this issue?
Log file:
Evaluating BIOS Options ...Launch BIOS Extension to setup ROMMON
Cisco Systems ROMMON Version (1.0(12)11) #4: Thu May 1 14:50:05 PDT 2008
Platform ASA5505
Use BREAK or ESC to interrupt boot.Use SPACE to begin boot immediately.
Launching BootLoader...Boot configuration file contains 1 entry.
[Code]...
Over the course of the past three days, our ASA 5505 firewall has shut down twice. I looked through the Field Notices and it looks like this was a problem identified several years ago that was resolved for units built after June 1, 2007. The serial number on our unit is not in the "effected" range.
View 1 Replies View Related