Cisco Firewall :: ASA 5520 No Address Available For SVC Connection
Oct 7, 2012
We recently replaced our Cisco 5510 with a 5520. I had the SSL Client VPN working on the 5510, I cannot get it working on the 5520. The IOS version is 8.2(5) and the ASDM version is 6.4.I run through the SSL Client wizard and get everything set up. When I try to get to my outside interface Internet Explorer just comes up with an error. When I try to connect through the Cisco AnyConnect client on my Android it used to come up with a "No address available for SVC connection". After deleting an address pool not even related to my SSL VPN profile I cannot get that far. I just get a "login failed". Even after I create a user with level 15 privilege and assign to my vpn group policy.I still get the "No address available for SVC connection" when I try to connect to the default profile, which doesn't really go anywhere.
We have a Cisco ASA 5520 and in order to conserve public IP addresses and configuration (possibly) can we use the same public IP address for a static NAT with two different interfaces? Here is an example of what I'm refering too where 10.10.10.10 would be the same public IP address.
I am trying to correctly configure our ASA 5520 and our Mitel Border Gateway in our DMZ. In the documentation for the Mitel border gateway it wants me to set up 2 external IP's on my ASA one to allow 443 traffice into the MBG, and another for 443 traffic that needs to be forwarded to port 4443 for the MGB in the DMZ. My problem is I don't know how to do this. the MBG only has one IP, and I need to have 2 different URL's mapped to two different external IP's both externally using port 443, and one of them forwarding to 4443 on the DMZ interface.
I have a handheld device that will be used for inventory outside of our office. It has 3g capabilities. Is there anyway I can permit traffic from this device from the outside world coming into my network? I need to open a couple of ports so it can hit the server. But I have no intention to open these ports up to the entire world. I use an ASA 5520 with a managed router from our provider. I looked around on the Cisco site and the only information I found was for permitting and denying traffic from devices that are within the network.
I am trying to connect two overlaping IP address sites ( see attached diagram). Site A LAN address will dynamic NAT to 10.1.1.0/24 at ASA5520.All the users from site A need to get services from site B ( DHCP, DNS, Mailbox,Print Servers, AD loggin etc). All the connections will be initiating from site A to B.
1-will all these services will run over NATed address.( dynamic) or I have to change to static NAT?
2- Any sample config for ASA 5520 for this type of network?
Got an ASA5520 running V8.2(3) and we want to upgrade our internet bandwidth. Our ISP says OK but we need to install different physical circuit, upgrade CPE router, etc.
Then they say, btw your globally allocated IPs will change - this is a problem as we have Site-to-Site VPN Tunnels, IPSEC RA, etc.
ISP are proposing to give us a 3 month period whereby old & new IP blocks will be routed to our ASA (by means of secondary IP address on their Cisco CPE).
Multiple IPs on the same physical i/f on the ASA require sub-interfaces/IP Addresses/VLAN ids on my "outside" i/f.
Is this going to horiibly break Site-to-Site VPN Tunnesl, IPSEC remote access ?
Will VLANs work at all with IPSEC on the "oustide" i/f at all ?
I have a problem with the connections to the remote webservice passing through ASA 5520 firewall. Connections are usually interrupted in perod of half an hour in every few days.
This ASA 5520 firewall is only one firewall in a path to the remote webservice.
During the interruption I find the logs:
UTC: %ASA--4-419002: Duplicate TCP SYN from dmz1:x.x.x.x/.... to outside:y.y.y.y/p with different initial sequence number
Teardown TCP connection 28309406 for outside:y.y.y.y/p to dmz1:x.x.x.x/.... duration 0:00:30 bytes 0 SYN Timeout
How I could find root cause? Could it be solution implemetation of TCP State Bypass?
I am not able to access the device via SSH .After connecting to teh console I have found that allowed SSh session are fully utilized with show resource usage command and the output is [code]
So I used show ssh session command to see who is using the sessions but in the output it has showed only one session and the output was [code]
I was wondering why it shows only one session above instead of showing all the 5 sessions which are utilized as confirmed by show resource usge command.We are usning some internal tool for ssh monitoring on device which is poling the device after a fixed interval for port 22 reachabilty .I dont think these tools are making any issue as this is secondary firewall and we are not facing any reachabilty issue for primary firewall.also we are using 10 min for idle ssh timeout.
I configured multiple vlan on my Cisco ASA5520. Everything work perfectly except RDP (3389) connections. The connections are established but but after a period of inactivity, the user is disconnected from server (black screen). The same problem happens with other type of connections (client/server), exemple : Oracle, file sharing. Before installing the ASA, computers and servers were in the same vlan and it worked well.
There's a notion of inter vlan timeout connection ?
I have a Cisco ASA 5520 that I'd like to be able to connect directly to our gigabit fiber connection (we're currently connected through a media converter that's causing problems). I've found the following:Cisco ASA 5500 Series 4 Port Gigabit Ethernet Security Services Module [URL]. I only need a single fiber connection, as opposed to the 4 copper + 4 fiber.
We are working with an ASA 5520 and it seems there is an issue with some email messages sent throught it. When there are many recipients in the emails the email messages are not sent, and I have revised the server an the only thing I see is connecting dropped. When I went to see ASA log and see this log report: ESMTP Classification: Dropped connection for ESMTP Request from 'interface': servername/portnumber to outside: IP address/25; matched Class 2: cmd RCPT count gt 100 tcp flow from interface:servername/portnumber to outside: IP address/25 terminated by inspection engine, reason - inspector disconnected, dropped packet. So I think there should be an inspection of ESMTP packets and if they detect an email message sent to over 100 addresses, then the packet is dropped, am I right? if so, what should I do to let those email messages be sent?
I have a Cisco ASA 5520 that we was working properly. I tried to create a VPN IPSEC to test but when I finished the wizard I lost the conection between the inside interface and outside. I use other interface for DMZ and other for printers network but this adapters are working properly. I have reviewed the NAT's and the ACL's but I don't see the problem?
I have delete the VPN IPSEC but it's still not working and I have the network down
Does the ASA treat an object-group with a network-object containing a range of IP addresses as a netmask? For example, I can apply this configuration without the ASA throwing any errors though the configuration calls for a 'net mask':
object-group network test network-object 192.168.0.0 192.168.63.255 ? network-object-group mode commands/options: A.B.C.D Enter an IPv4 network mask sh run ob id test object-group network test network-object 192.168.0.0 192.168.63.255
I found that in the documentation it requires a netmask as oppose to a range. Is this a bug in the code? I am running code version 8.0(5)23 on a 5520. If this is not a bug how does the ASA treat this type of configuration when applied to an access list? When I ran a quick packet trace and denied access from that range it looks like the ASA doesn't read that configuration properly.
I have a server in a DMZ behind the ASA, connections to this server work sometimes and then fail others, so I dont think i'm looking at an ACL or NAT problem here.The syslogs report a SYN Timeout,I have taken a trace on the ASA, it seems that a SYN-ACK does come from the destination server within the 30sec timeout, but its not passed through the ASA back to the source ? there is one odd thing, what seems to be an out of sequence ACK from the destination which arrives before the SYN-ACK at the ASA, i'm wondering if this might be the problem ? This only occurs on the connections which fail, the connections that work, the destination responds quickly to the initial SYN, and the 3way handshake completes.
Syslogs :
Oct 18 19:17:32 nzlsudfedsi001-pri Oct 18 2011 19:17:32 NZLSUDFEDSI001 : %ASA-6-302013: Built outbound TCP connection 42327212 for IIP-ARCHIVE-PROD:172.24.32.31/21 (172.24.32.31/21) to BPO-TRANSIT:x.x.x.x/59392 (x.x.x.x/59392) Oct 18 19:18:02 nzlsudfedsi001-pri Oct 18 2011 19:18:02 NZLSUDFEDSI001 : %ASA-6-302014: Teardown TCP connection 42327212 for IIP-ARCHIVE-PROD:172.24.32.31/21 to BPO-TRANSIT:x.x.x.x/59392 duration 0:00:30 bytes 0 SYN Timeout
Ive got a virtualised firewall running 3 security contexts in routed mode. What am experiencing is that i cannot connect to an OUTSIDE host through the security contexts. From the firewall itself i cannot ping the directly attached host on the OUTSIDE interface but i can ping the directly attached host on the INSIDE interface. When i reload the firewall box, the first ping to the OUTSIDE host would be successful but subsequent pings fail and thus total connectivity is lost.
I even tried upgrading to ASA version 8.4(1) but still the same.
We have ASA 5520 firewall.For broadband Internet access, we have T1 Router(edge router provided by ISP) which provides public IP's 198.24.210.224 / 29. We have usable public IP's 198.24.210.226 - 198.24.210.230 with default gateway 198.24.210.225. We assigned 198.24.210.230 255.255.255.0 to the outside interface.
If we connect the ASA 5520 outside interface directly to T1 router, can all packets with destination addresses 198.24.210.224/29 reach the outside interface without using other device like another router or switches?I just assume that only packets with destination address 198.24.210.230(outside interface ip) can reach the outside interface from the edge router.Is it wrong assumption? If it is correct, then is there any way to route all packets with destination address 198.24.210.224/29 to the outside interface?
I am using a pptp server running on windows 2008 server and I have configured my ASA 5520 to let the PPTP traffic to pass throught.
The solution works quite well but exactly every 120 minutes the connection drops and people have to reconnect. Is there any setting to change? In the PPTP server I haven't found any setting to change.
Currently in our environment we have have two buildings with an ASA 5520 in each and a core stack of 3750's in each building. I am currently working on a network segmentation project and am thinking of adding another stack of 3750's in each building to add more redundancy to our network. This will allow our access layer switches to have a trunk to each stack and prevent an outage if one of the links or stacks were to go down.
My question is how I would set this up on the ASA end of things while using a common subnet and HSRP on the 3750's. I understand how to use HSRP and STP on the switches to achieve this on the 3750 end of things. I saw you can do etherchannel on the ASA with 8.4 but how does that work in a failover situation?
I have a client that has an ASA 5520 that has two internet connections, FIOS and Comcast. The ASA is configured to failover from the FIOS to the Comcast if the FIOS fails. This works perfectly fine. However, I was wondering if VPN and other inbound traffic will come into the secondary connection when it is active. I think VPN will work inbound when the FIOS connection fails, but I am not sure about the other inbound connections.
We're currently PATing everything from a particular subnet to the IP of an outside interface using our ASA5585 (dynamic PAT). We're experiencing pool exhaustion and therefore need to expand the global IP range. Any way of cutting over to the new range without dropping existing connections? For clarity, the current interface address is x.x.x.37/22 and the new PAT pool is x.x.x.114-6/22.
Using Cisco ASA5510 Security Plus (Post May 2010) with 8.2(1)
I was trying to limit the number of internet IP Address that can initiate Remote Access VPN connection to the firewall. I have plan to only allow internet IP Address from few ISPs for control.
However, blocking AHP, ESP, ISAKMP, NON500-ISAKMP, and IPSec Over TCP Port Assigned in the firewall outside interface doesn't work. But it works by putting the ACL in the router before the firewall. It seems that the firewall have a "hidden" process VPN first before user entered ACL (or explicit rule), similar to Checkpoint FW's implied rule. How to get around it?
I have an iPAD. It connects to my ASA5520 via IPSEC. When it connects it gets an IP address from the ASA but it does not get any of the other stuff. Specifically the DNS suffix. How to correct it?
We were using ASA-5520-K9 with ASA-SSM-AIP-20-K9 but recently found some hardware problem in our running ASA. Now cisco want to replace with ASA-5520-K8.
i have a site to site vpn stablished, the vpn works fine (while is up), i have a cisco asa 5520 and the other end of the vpn is a jupiter device that for technical reasons needs to send a continuos ping and when it does not receive a reponse back it brings down the vpn tunnel and reestablish it again. while the vpn is up traffic flows perfectly but because i m unable to repond to the ping the vpn is brought down as reestablished by the jupiter device. the jupiter device pings the encryption domain which is an ip that is natted to the real ip in the inside network. this is my configuration of the vpn:
AAA.AAA.AAA.AAA is the ASA public ip in the outside BBB.BBB.BBB.BBB is the jupiter device ip (part of the object group IP_LIST) CCC.CCC.CCC.CCC is the nat ip on the ASA 10.21.0.164 is the real address in the inside(code)
I guess I'll start with the easy stuff, Cisco ASA 5520 ver 8.2, ASDM ver 6.2, IPSec L2L tunnel with overlapping private IPs.
I have about a dozen L2L connections on our 5520 but never had to do one with overlapping IPs. I have two that I have to build and one definitely overlaps our inside locals, and the other is requesting that we NAT our inside locals to a 10.x.x.x.
I've searched the board and found several good posts including document 112049, but I just don't seem to be able to get my head around how to translate one inside address to another. It would seem like is would be as easy as doing an (inside,inside) static NAT, but most everything has the solution as a policy NAT or doing an (inside, outside) but in the less secure address space place the name of an ACL. I have ordered that brick of a book on ASAs from Cisco Press, but need to get something going and I'm not having much luck getting this thing up and running.
Perhaps my basic understanding of NAT rules is wrong. I thought that when using NAT the command speaks to the interfaces and the direction of travel, (inside,outside). I also thought that the IP adresses used must be valid on the interface refferenced, so any refference to "inside" would have to be an address on the "inside interface of the FW and likewise for the "outside" interface. Finally, to be sure I'm not calling a duck a goose my understanding is that the following are correct; "inside local" = my private, "inside global= my peer, "outside local"= their private, "outside global"= their peer.
So if I'm translating say a 192.x.x.x on my inside local and wanted to present them a 10.x.x.x, wouldn't I need an (inside,outside)? And even though I'm translating my private IP into a different private IP, the translated IP must be on the "outside" interface because that is the interface that I want to present the new private IP on?
So for the scenario I suggested at the top where I need to translate my private 192.x.x.x into a 10.x.x.x and present that 10.x.x.x to the other side, I need something like NAT Static (inside,outside) 10.x.x.x 192.x.x.x?
I've been tasked with retiring a VPN Concentrator 3000 and replacing it with an ASA 5520. I'm trying to get a handle on how to set up the NATs and ACLs, since most of my experience is remote access VPNs, not site-to-site. Plus I've not configured a VPN 3000 in about 6 years so I'm having to re-learn a lot of the interface.
The VPN 3000 has a feature called LAN-to-LAN NAT rules that basically allow you to NAT an address on your internal network to an address on the "local" network for the LAN-to-LAN connection so it can then go through the tunnel to the remote side. The config looks something like this in the VPN 3000: [code]
Which looks to me like a "Static Policy NAT" in ASDM. So I set one of those up, that should be translating 172.16.3.151 on the inside interface to 192.168.200.151 on the inside interface (yes, the same interface) which should then (logically) be picked up as "interesting traffic" by the crypto-map and sent across the VPN tunnel. However, that doesn't seem to be the case - both the "packet trace" in the ASDM and traceroute from the source workstation show the packets getting to the inside interface, and then passed right out the outside interface to the internet router (which then drops the packets as they're a private IP).
what else do I need to do to make the crypto-map pick up the NATted traffic?
We are using Any connect vpn client (v2.5.3055) to an ASA 5520 (v8.4) in a development environment. We use our corporate Radius server to authenticate users. We have certain users which need have the same IP address every time they lo gin. As it is configured now, the IP addresses are assigned sequentially from the pool. Is there a way to allow certain users to get the same IP address each time they log on?
I have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
I am having some challenges on my DMZ network.My servers and Cisco Switches in the DMZ are picking the mac address of the Firewall(Cisco ASA).I have put some static arp entries on the Firewall and switches but the servers and users on the DMZ are still receiving the mac address of the Firewall.How can i stop the Firewall from changing the mac addresses of the devices on the network.My ASA is a 5520 and i have 2960Switches.
I'm visiting family and my laptop will not connect to their wireless. I plugged it in and it connected, but wireless will not. I've tried to renew my ip but it tells me media is disconnected. How do I connect the media? I'm in the device mgr now, looking at network adapters. have yellow !! on Microsoft ISATAP Adapter #5. I opened it and there is no "value" for Network address. I've got Acer Aspire 5520, w/SP2, 2.00GB, 32-bit,AMD Turion 64 X2 1.80 GHz. Windows Vista Home Premium. message rec'd is "No operation can be performed on wireless network connection while it has its media disconnected."
