I have managed to simulate to Cisco ASA's on GNS3 - ASA1 and ASA2. ASA2 is configured as multiple mode to enable contexts while ASA2 has been configured as single mode.
On ASA2 I can assign an IP address to its gigabitethernet interfaces as normal, however I'm unable to assign an interface to the gigabitethernet interfaces on ASA1.
I have to use GNS3 for simulate ASA5540.but it does not work. I've installed latest GNS3(0.8.3.1 all in one) in Win7 32bit environment, and used IOS file is asa842-k8.bin.but i can't unpack it properly. it said "Couldn't find any ZIP header in asa842-k8.bin".
View 2 Replies View RelatedI'm using GNS3 in order to revise CCNA, the RIP part But I don't know why, i'v got a pbl with the routage table, especially with the metric which is wrong I don't understand wy the metric is always 1, because it should be 2 or 3 according to the network.
View 5 Replies View RelatedI am currently doing some research (for my employer) into creating multi-context sub-interfaces on a Transparent ASA 5550.
I have not been able to find any details on this subject which state it is or it is not possible. This will be used for Syslog logging.
I am trying simulate the next lab on GNS3 but the ping don't work between hosts on the same VLAN.
View 2 Replies View RelatedI am trying to connect my Ubuntu PC with gns3 router using loopback interface tap0, I am trying to configure the ip address of tap0 by using gns3 router as DHCP Server. But I am finding it difficult to do so.
View 2 Replies View RelatedI have been configuring the SG-300 28 from both web and cli interfaces.When doing a sh run I get Int gi2 before int Gi1? WTF?Also one of my vlans wasn't working on interfaces but was working through the assigned trunk port to my other switch.I deleted it and recreated it and it is now working. Why we have a failure and go to reconfigure a switch and have these same issues.
View 1 Replies View RelatedI'm having some trouble configuring porting between interfaces.Here is my situation.I have a Cisco 891 router. What I need is to create 3 interfaces with the next IPs:
1. Port FastEthernet 8 - 20.40.1.1 - with a modem connected directly to it - 20.40.1.2
2. Port GigabitEthernet 0 - 193.2.5.100 - connected to a switch - LAN
3. Ports FastEthernet 0 and 1 for two VOIP phones - 190.168.5.2 and 190.168.5.3 - will be switchported to VLAN 10 - 190.168.5.1
I can send ping from a PC (193.2.5.1) to the modem interface (20.40.1.1) but not to the modem itself (20.40.1.2).I played days with configurations and tried a lot of variation of ip routing and access-lists with no success.Basically I need to comunicate freely betwin all the devices.There are a lot of forums providing solutions to a same problems but they seems not working with the 891 router. Any way, assuming I have a factory resetted router? [code]
configuring my Cisco 2951 router. There are three routed interfaces that I need to configure: one for the internal LAN, the second for another private subnet that connects to a Data Centre and the third for the WAN connection. I have configured the Ge0/0 interface as the LAN interface with the internal network 10.17.0.0/24. I have also configured my WAN interface Ge0/1 for internet connectivity. Now, I need to configure the third interface Ge0/2 that will connect to the Data Centre. This will be a private point to point switched ethernet link. The Data Centre will host a secondary domain controlller. So, I want it to be on the same network as the internal LAN, i.e., 10.17.0.0/24. I want to be able to see all other devices that will be located at the Data Centre just like I would see all devices connected to the internal LAN.The problem I am facing is that Cisco 2951 does not allow me to configure two routed interfaces to be on the same subnet. Is there any way to work around this problem and configure both the internal LAN and the Data Centre private network to be on the same subnet.
View 6 Replies View RelatedAny one has succeeded in simulating ASA 8.2(not ASA 8.02) in GNS3 ?
I see some are very close in getting it running on GNS3...
[URL]
I have to test new Cisco ASA's IOS version 8.4 in my GNS3 LAB . do provide the link for downloading the same.I dont have direct download access from cisco.com.
View 1 Replies View RelatedI'm about to setup as ASA configuration with GNS3 ASA. how to best test the configuration once complete? I need something like a verification plan to ensure that the configuration would perform if in production.
View 1 Replies View RelatedSo I have to complete a lab using OPNET and I've attempted to complete it using the the step by step lab outline 3 times now, and each time, it fails to capture the Client_HTTP Page Response Time statistic on the 10-T lan based in africa. It's failing to capture it in all 3 scenarios, so something must be wrong in the configuration. As I've said, I've redone this lab 3 times, so something must be wrong in the manual.
View 3 Replies View Relatedconfiguring NAT on intranet firewall. here is the my topology:
DMZ Network - - - - - - - - - External Firewall - - - - - - - - - Internet
|
|
|
Internal Network - - - - - - - - - Internal Firewall
1) I can Ping the intneral host from external firewall, internet firewall and DMZ network
2) Both ASA's are running OS Version 9.0(1)
3) ACL used permit IP any any, on both (i.e inside and outside)
NAT configuration on Internal Firewall (Identity NAT)
object network MGMT-SRV-INSIDE subnet 10.10.10.0 255.255.255.192
object network MGMT-SRV-identity
subnet10.10.10.0 255.255.255.192
object network MGMT-SRV-INSIDE nat (Inside,Outside) static MGMT-SRV-identity
[code]....
In ASA 8.0,I have following queries related to redundant interfaces
a)While configuring redundant interface can the redundant interface again be divided into logical interface like red1.1 , red1.2 ?
b)Is Redundant interface supported in the Multiple context mode
Having upgraded to 8.3 from 8.2 I and read much about the differences , it seems that 8.3 deals with NAT in a much more managed method.However I am confused on how one would NAT a network object to multiple interfaces? i.e I know you can specficy a NAT adddress within the network object howeveer this only allows you to specific a single IP address.What if I want to talk accross multiple interfaces how would I specify this?
View 5 Replies View Relatedi have an ASA 5520 running ver 8.4(1). have attached my interface config below and need to do the following, NAT traffic coming on GigabitEthernet0/2.101 to GigabitEthernet0/1, i.e. packets with destination 10.21.110.25 will be forwarded to 10.11.21.25, will a nat (Production,Advocate_MPLS) static ... statement work ?
------------------------------------------------------------------------
interface GigabitEthernet0/1
description Production
nameif Production
security-level 100(code)
I have put 2 physicl interfaces (te0/8 & 9) on the ASA-5585 into a PO and am assigning ips/vlans to the sub-interfaces. I have 2 issues: - Why am I not able to ping the other sub-interface from the ASA itself? (I can ping the 1st one), Secondly, why the IPs are not visible in "sh int ip brief" ?Although I can see them in "sh ip" ..
/actNoFailover(config-if)# int po17.100
/actNoFailover(config-subif)# vlan 100
/actNoFailover(config-subif)# ip add
[Code]....
Do i need to create 2 objects for nating a server to 2 different interfaces?That is an inside server published in two different dmzsAutomatic migration to 8.3 creates 2 objects (one for each nat)Can I do the same with only one object? like this or I need an object for each nat?
object network server
host 192.168.128.10
nat (inside,dmz) static 172.24.1.10
nat (inside,dmzguests) static 10.10.0.10
Can ASA sub-interfaces run separate IP Sec VPN tunnels eg
There are 02 sub-interfaces of 01 physical interface of Cisco ASA5510 [ASA Version 8.2(5)] and I need to run 01 IP Sec VPN tunnel on each of these
We have an ASA 5510 firewall. There are 4 ports on it configured as 2 outside, one inside, and one DMZ. We have two cable modems attached to the outside ports. Our plan is to have the "inside" port directed to one outside port/cable modem, and the DMZ port directed to the other outside port/cable modem.
We have been able to get the "inside-to-outside" setup to work but not the "DMZ-to-outside" setup (at least at the same time).First off, is this possible? If so, what are we likely missing - some way to have a second default route for the DMZ?(My manager is the "Cisco person" here, not me, so I may not have enough info.
I have a pair of brand new 5520s I am in the middle of commission. After carving out all the DMZs etc I needed I realized that I really neede another physical NIC, not just another VLAN off a configured nic. [code]I am running 8.3(2). How can I turn these "Not used" interfaces into useable ones?
View 2 Replies View RelatedI configured ASA 5510 ...
Totally it had 5 ports..
How to provide communication between two different interfaces which had configured as same security level?
How many trunks will support ASA 5510 with base-license?
How to configure trunk to an interface with different VLNs( Router on a stick).
I have a problem on allowing ssh traffic between 2 different INTERNAL interfaces. Both the interfaces have the same security level (100).What I have to do is to allow a ssh command from 172.16.0.2 to 172.17.1.200. The firewall is configured but I am experiencing issues on the NAT.The error I get is as follows:#%ASA-5-305013: Asymmetric NAT rules matched for forward and reverse
View 3 Replies View RelatedWe have ASA FW 5010 in our organization and we have 4 DMZ's under the DMZ interface on ASA and all DMZ's are created on sub interfaces and assigned different VLANS on each DMZ's.
View 7 Replies View RelatedWe have an ASA 5520 which is in multiple context mode. We are trying to pass traffic from the outside interface to the dmz interface. We have a /27 public ip range. We need a small amount of those addresses to be in the DMZ for SIP servers specifically. The rest of the addresses are NAT'd to the inside interface.So i created the outside interface GigabitEthernet0/0 with 1.2.3.192/28 Inside Interface GigabitEthernet0/2 with 192.168.20.0/24 DMZ interface on GigabitEthernet0/2.1 with 1.2.3.208/29 So all i want to do is route traffic that comes in the outside interface and out to the DMZ interface for the 1.2.3.208/29 subnet. I set the gateway address as 1.2.3.214 which is the DMZ interface address on the ASA.
View 20 Replies View RelatedOur ASA 5520 firewall is running 8.0(4) IOS.I have an internal L2L VPN terminating on my firewall (from an internal remote site) on ENG interface.With the default "sysopt connection permit-vpn" command enabled, VPN traffic is allowed to bypass the ENG interface acl.The security level on the ENG interface is set at 50.The security level on the destination interface PRODUCTION is set at 40.Inbound VPN traffic bypasses ENG interface acl and since higher-to-lower security level allows VPN traffic to flow freely from ENG to PRODUCTION, it seems the only place to check/filter VPN traffic is an ACL placed on the PRODCTTION interface and set at INBOUND (outbound VPN traffic).
View 4 Replies View RelatedWe are using Cisco ASA 5580 (8.2) firewall. When i try to ping from inside lan to firewall DMZ interface IP it is not pingable and but from inside users i am able to ping firewall inside interface IP address.
I think we can't ping to other interfaces of ASA by default. But can we allow the single IP address who can ping all the interfaces of firewall?
We are not doing any natting in firewall, for that we used the Load Balancer.
I am using an ASA5550 for a complex secure network that has at least six "outside" networks. Each "outside" network is assigned to a specific port each set at level "0". I also have a DMZ, set to level "50". I am having difficulty with passing traffic from a host in the DMZ to all but one of the "outside" networks. Is there a limit to the number of "outside" interfaces? I will provide a redacted config file as soon as possible.
View 3 Replies View RelatedGot new ASA5550, code 8.2.2 in flash, can't configure "nameif" or "ip address" on the interfaces: [code] These are all the options that I get! Another weird thing I noticed is "<system>" string in "show ver" top line: [code]
View 2 Replies View RelatedI have a Cisco ASA 5520 running 8.2.2 with the VPN Plus license. I am wondering what is the max number of sub-interfaces you can have on a physical interface. I know on the 5505 it was 20 sub-interfaces if you were running the Security Plus license. What is the magic number for the 5520. I have hit 20 sub-interfaces on gi0/1 interface and now I am starting to run into problems with sub-interface #21.
View 1 Replies View RelatedI have a cisco ASA 5520 that i'm configuring.From the actual Firewall (with is a linux server), we have the outside interface eth0 with has a public IP and other sub-interfaces (eth0.1; eth0.2,...) with others publics IPs.I'd like to know how I can configure it in an ASA
View 7 Replies View RelatedI am working on translating configuration from a firewall named Joe box to ASA 5515. On Joe box, it has 5 continuous public IP addresses (xx.xx.xx.73 -77/29), first one as interface IP and others as alias, on the Internet-facing interface. I need to configure ASA 5515 in the same way, however it seems not simple.
- The way to configure sub interfaces on 5515 is by configuring V LAN.
- The interface can hold xx.xx.xx.73/29 without a problem.
- The first sub interface can have IP address xx.xx.xx.74 however with different mask(/16), as it doesn’t allow /29.
- The second sub interface doesn’t allow to enter IP xx.xx.xx.75, saying "Failed to apply IP address to interface GigabitEthernet0.x, as the network overlaps with interface GigabitEthernet0. Two interfaces cannot be in the same sub net."