I know with a ASA5510-SEC-BUN-K9, you can increase eth0/0 and eth0/1 to gigabit with the right IOS. Is the same possible with the CSC version of the ASA?
Exact pn is ASA5510-CSC10-K9. I believe I only have the base license for the ASA, but the security plus for the CSC.
We have an ASA 5510 firewall. There are 4 ports on it configured as 2 outside, one inside, and one DMZ. We have two cable modems attached to the outside ports. Our plan is to have the "inside" port directed to one outside port/cable modem, and the DMZ port directed to the other outside port/cable modem.
We have been able to get the "inside-to-outside" setup to work but not the "DMZ-to-outside" setup (at least at the same time).First off, is this possible? If so, what are we likely missing - some way to have a second default route for the DMZ?(My manager is the "Cisco person" here, not me, so I may not have enough info.
We have ASA FW 5010 in our organization and we have 4 DMZ's under the DMZ interface on ASA and all DMZ's are created on sub interfaces and assigned different VLANS on each DMZ's.
View 7 Replies View RelatedI am trying to determine if this is possible or not. I have tried several configurations and I can only get half of it to work.
LAN (10.1.1.0/24) =====> <===== OUTSIDE (T-1)
ASA5510
DMZ (10.1.10.0/29) ====> <===== BACKUP (DSL LINE)
The Cisco ASA5510 currently is configured with the following interfaces: inside, outside backup, and dmz.The backup interface routes to the internet via a DSL modem, it normally is not active.The outside interface routes to the internet via a T-1 line.The inside interface is our local LAN and the DMZ has our email server on it.I am wondering if there is a way to configure the ASA5510 so all internet traffic from the inside LAN goes only through the DSL modem and all the DMZ traffic only goes through the T-1 line. No inside traffic (inbound or outbound) should go through the T-1. No DMZ traffic (inbound or outbound) should go through the DSL line.
I can get the LAN to use the DSL line with no problem, but the DMZ to T-1 side causes reverse-path errors.I am not looking for redundancy or failover protection.
I have an ASA5510 running 8.2 code and I have over 200 static nats from the outside to the inside interface and that is how I expose our systems to the Internet. If this inside interface fails we also have a bypass interface that also terminates on the internal network but I am not sure how the nats will behave given they are statically mapped to the inside.
View 1 Replies View RelatedI am using Cisco ASA5510 Firewall in my network. Upgraded the Memory and Flash to 1GB and 512MB.But the 5 interfaces ports are 10mbps.Can it possible to upgrade the module of Interfaceses from 10mb to 1gb?
View 2 Replies View RelatedI am trying to configure two inside interfaces without NAT. I am not using nat-control and I have added exemptions for the two networks. I can communicate between the two networks and to the Internet just fine.I would like to verify that NAT is disabled between the two interfaces. I also need to make sure that the Interface IP (specifically for the traffic from inside-test to the inside network) is not added to packets between the two networks. I would like to be able to verify this as well. In other words I need to have the Source IP address from the originating connection on the inside-test network passed along through to the Inside network device without being replaced by the Interface's IP address. This is a test config for a production environment that will be using a load balancer. The config I have may be working in this regard and the load balancer may be replacing this IP address (that is what I am trying to test), but I am not certain.So far I have the following NAT related running-config command (in regards to these two interfaces):
access-list NAT_Exempt extended permit ip 192.168.12.0 255.255.255.0 interface insideaccess-list NAT_Exempt extended permit ip 192.168.3.0 255.255.255.0 interface Inside-testaccess-list NAT_Exempt extended permit ip 192.168.12.0 255.255.255.0 192.168.3.0 255.255.255.0access-list NAT_Exempt_2 extended permit ip 192.168.12.0 255.255.255.0 interface insideaccess-list NAT_Exempt_2 extended permit ip 192.168.3.0 255.255.255.0 interface Inside-testaccess-list NAT_Exempt_2 extended permit ip 192.168.3.0 255.255.255.0 192.168.12.0 255.255.255.0
nat (inside) 0 access-list NAT_Exempt_2nat (inside) 1 0.0.0.0 0.0.0.0nat (Inside-test) 0 access-list NAT_Exemptnat (Inside-test) 1 0.0.0.0 0.0.0.0
global (outside) 1 interfaceglobal (Inside-test) 1 interface
I've been trying to figure this one out for quite a while. I currently have 2 inside interfaces (data, phone) and I am moving to 3 inside interfaces (servers, workstations, phones). I have not been able to get any traffic between the interfaces. With the current setup it was not a major problem. With the new setup it will be a major problem.
Below is a sanitized version of the config.
ASA Version 8.2(1)
!
hostname BOB
[Code].....
Today I run into a problem with enabling ICMP traffice between two inside interfaces on ASA5510 (version 8.2). I tried to ping from 192.168.1.2 to 192.168.2.2 Failed. But I can visit outside websites or ping from any of the two addresses above to 8.8.8.8 So I checked the configuration shown as follow
<omitted>
interface ethernet0/1
nameif inside
[Code]....
We have a Cisco 7206 VXR Router with NPE-G2. As everybody aware that, It has got 3 x Gigabit Ethernet Ports on this. We would like to add Two more Copper Gigabit Ethernet Interfaces. The Configurator does not show any options to add that...
Now we have a doubt that, Does this 7206 VXR support how many Copper Gigabit Ethernet Interface ?. There is no clear answer available in the Data Sheets.
On a 3750 switch, is it possible to configure jumbo frames only on certain interfaces and leave the other ones as they are?
View 9 Replies View RelatedI currently have a site to site VPN running connecting a branch office and the Main office using a ASA5510 and ASA 5505. currently PC's at the branch can access the network in the main office using interface 0/1, but we have added another ip range using interface 0/2 and I can't seem to route the traffic to both interfaces. I currently have 0/1 as inside 192.168.10.1 which works, and have added 0/2 as Inside2 192.168.20.1. I know I am forgetting something, any commands to route incoming VPN traffic so PC's at the branch office can connect to both IP ranges?
View 14 Replies View RelatedASA 5510 have two model Bun-K9 and Sec-Bun-K9 from the datasheet find out difference Port related and Redundancy. My questions is : Have any major difference for Security service between two model ?
View 3 Replies View RelatedI have an Ethernet Loopback Plug (4 Pairs) made and trying to test the Gigabit Interface on a 3845 Router with a fail result. The interface will show up/up only if I set the interface to 100M/Full Duplex when I plug-in the Ethernet Loopback Plug (4 Pairs). I don't see this Gigabit Interface @ 3845 router has any option to set it to internal or external loopback.
View 2 Replies View RelatedI'm running an Optiplex 330 with the Broadcom NetXtreme 57xx Gigabit ethernet card.
The computer is running Windows 7, 64bit, but there do not appear to be any drivers for that OS.I tried selecting Vista 64bit, but there were no drivers. The Vista 32bit doesn't work.
Then I went to Broadcom and found these drivers: [URL] the W764bit drivers didn't change the fact i'm still on a 100Mbit card (as seen on Local Area Connection Status screen and the Device manager)
I am able to ping from Switch to firewall inside ip and user desktop ip but unable to ping from user desktop to FW Inside ip.. config is below for both switch and FW Cisco ASA5510....
TechCore-SW#ping 172.22.15.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.22.15.10, timeout is 2 seconds:
[Code].....
I have two ASA5510's set up in failover, and the secondary keeps crashing after doing the interface checks when bringing failover up. This only happens if I try to upgrade the image on the secondary to anything newer than 8.4.1 (I've tried with 8.4.1-11 and 8.4.2). The primary one run just fine with new images.
I don't have the exact error right now, as I need to do a screen capture from console. It's just a huge crash dump.Are there anything I might have missed during the upgrade? Should I cold-boot both the firewalls in the correct order?
In ASA 8.0,I have following queries related to redundant interfaces
a)While configuring redundant interface can the redundant interface again be divided into logical interface like red1.1 , red1.2 ?
b)Is Redundant interface supported in the Multiple context mode
Having upgraded to 8.3 from 8.2 I and read much about the differences , it seems that 8.3 deals with NAT in a much more managed method.However I am confused on how one would NAT a network object to multiple interfaces? i.e I know you can specficy a NAT adddress within the network object howeveer this only allows you to specific a single IP address.What if I want to talk accross multiple interfaces how would I specify this?
View 5 Replies View Relatedi have an ASA 5520 running ver 8.4(1). have attached my interface config below and need to do the following, NAT traffic coming on GigabitEthernet0/2.101 to GigabitEthernet0/1, i.e. packets with destination 10.21.110.25 will be forwarded to 10.11.21.25, will a nat (Production,Advocate_MPLS) static ... statement work ?
------------------------------------------------------------------------
interface GigabitEthernet0/1
description Production
nameif Production
security-level 100(code)
I have put 2 physicl interfaces (te0/8 & 9) on the ASA-5585 into a PO and am assigning ips/vlans to the sub-interfaces. I have 2 issues: - Why am I not able to ping the other sub-interface from the ASA itself? (I can ping the 1st one), Secondly, why the IPs are not visible in "sh int ip brief" ?Although I can see them in "sh ip" ..
/actNoFailover(config-if)# int po17.100
/actNoFailover(config-subif)# vlan 100
/actNoFailover(config-subif)# ip add
[Code]....
Do i need to create 2 objects for nating a server to 2 different interfaces?That is an inside server published in two different dmzsAutomatic migration to 8.3 creates 2 objects (one for each nat)Can I do the same with only one object? like this or I need an object for each nat?
object network server
host 192.168.128.10
nat (inside,dmz) static 172.24.1.10
nat (inside,dmzguests) static 10.10.0.10
Can ASA sub-interfaces run separate IP Sec VPN tunnels eg
There are 02 sub-interfaces of 01 physical interface of Cisco ASA5510 [ASA Version 8.2(5)] and I need to run 01 IP Sec VPN tunnel on each of these
i have a ASA5510 in the office, that already configured 3 context, namely, admin, user, server.in the server context, the last running config was not saved, and there was a power trip last friday night. 1 of the sub interface was affected, and i need to recreate that interface.I am getting the below error, it only allow me to do changes those pre-defined interface.how to I create extra sub interface?
View 3 Replies View RelatedI have a ASA5510 and I have a question about the speed the ports can handle, here is one port:
-interface Ethernet0/2
- speed 100
-shutdown
- no nameif
-no security-level
-no ip address
it's ethernet and not fastethernet so I figure it will only go to 10Mbps, but at the same time I can hard code the speed to 100.
i have cisco ASA 5510 Firewall using in my network, i have planning to upgrade the Flash memory from 256 mb to 512 mb and the RAM from 256 mb to 1GB.
View 1 Replies View RelatedI have a pair of brand new 5520s I am in the middle of commission. After carving out all the DMZs etc I needed I realized that I really neede another physical NIC, not just another VLAN off a configured nic. [code]I am running 8.3(2). How can I turn these "Not used" interfaces into useable ones?
View 2 Replies View RelatedI configured ASA 5510 ...
Totally it had 5 ports..
How to provide communication between two different interfaces which had configured as same security level?
How many trunks will support ASA 5510 with base-license?
How to configure trunk to an interface with different VLNs( Router on a stick).
I have a problem on allowing ssh traffic between 2 different INTERNAL interfaces. Both the interfaces have the same security level (100).What I have to do is to allow a ssh command from 172.16.0.2 to 172.17.1.200. The firewall is configured but I am experiencing issues on the NAT.The error I get is as follows:#%ASA-5-305013: Asymmetric NAT rules matched for forward and reverse
View 3 Replies View RelatedWe have an ASA 5520 which is in multiple context mode. We are trying to pass traffic from the outside interface to the dmz interface. We have a /27 public ip range. We need a small amount of those addresses to be in the DMZ for SIP servers specifically. The rest of the addresses are NAT'd to the inside interface.So i created the outside interface GigabitEthernet0/0 with 1.2.3.192/28 Inside Interface GigabitEthernet0/2 with 192.168.20.0/24 DMZ interface on GigabitEthernet0/2.1 with 1.2.3.208/29 So all i want to do is route traffic that comes in the outside interface and out to the DMZ interface for the 1.2.3.208/29 subnet. I set the gateway address as 1.2.3.214 which is the DMZ interface address on the ASA.
View 20 Replies View RelatedOur ASA 5520 firewall is running 8.0(4) IOS.I have an internal L2L VPN terminating on my firewall (from an internal remote site) on ENG interface.With the default "sysopt connection permit-vpn" command enabled, VPN traffic is allowed to bypass the ENG interface acl.The security level on the ENG interface is set at 50.The security level on the destination interface PRODUCTION is set at 40.Inbound VPN traffic bypasses ENG interface acl and since higher-to-lower security level allows VPN traffic to flow freely from ENG to PRODUCTION, it seems the only place to check/filter VPN traffic is an ACL placed on the PRODCTTION interface and set at INBOUND (outbound VPN traffic).
View 4 Replies View RelatedWe are using Cisco ASA 5580 (8.2) firewall. When i try to ping from inside lan to firewall DMZ interface IP it is not pingable and but from inside users i am able to ping firewall inside interface IP address.
I think we can't ping to other interfaces of ASA by default. But can we allow the single IP address who can ping all the interfaces of firewall?
We are not doing any natting in firewall, for that we used the Load Balancer.
I am using an ASA5550 for a complex secure network that has at least six "outside" networks. Each "outside" network is assigned to a specific port each set at level "0". I also have a DMZ, set to level "50". I am having difficulty with passing traffic from a host in the DMZ to all but one of the "outside" networks. Is there a limit to the number of "outside" interfaces? I will provide a redacted config file as soon as possible.
View 3 Replies View Related