I am looking for a way, even something that might be EOS, that will allow autonomous AP1200s to force a user to enter a user name and password (or even just password) before allowing a user network access. This is a hotel environment so even though the first client authenticates the process needs to be initiated again whenever a different laptop comes onto the network.
View 14 Repliesis it possible to set the dot1x guest-vlan on a Catalyst Switch via ACS 5.2 dynamicly. I want to make MAB with known Devices (FAT-Clients, Notebooks, Desktops, Printers) and unknown Devices.I will set the VLAN dynamicly with dot1x per ACS. For known FAT-Clients, Notebooks etc. it's running well.But for Printers it's more difficult because I have about 500 Printers in several IP-Segments on several Switches and I will not make to much Rules in ACS for Grouping, Mapping and Authority-Rules.My Idea is to set the Guest-VLAN on every Switch, read them with ACS and use this for my Printers.The Problem is that Guest-VLAN is set on more than 100 Switch and this guest-vlan is different on any Switch.Can I read the Geust-VLAN Value so that I can set this via ACS ?
View 4 Replies View RelatedFor some reason, i can't get the lobby "sponsors" to authentication to the Guest NAC server (2.0.2) using ACS 5.2 via Radius.I was able to figure out how to get the Guest NAC Radius Authentication for "Administrator" to work by adding custom Radius value IEFT-6 under...
Policy ElementsAuthorization & permissionsNetwork AccessAuthorization Profiles
I added a policy & under the Radius Attributes Tab... I manually entered an Attribute that looks like the following:
Dictionary Type: = RADIUS-IETFRadius Attribute: = Service-TypeAttribute Type: = EnumerationAttribute Value: = StaticValue = "Administrative"
I then created an Access Policy... I looked for a specific AD group - Result = "Name of Custom Policy Above"...
All of that is working just fine.... the NAC Guest Docs tell you the Radius server must return a value of IETF-6...
When it gets into the Sponsor section, it doesn't tell you the value your Radius server should return... so just for grins, instead of "Name of Custom Policy Above", I tried "Permit Access"... i tried the "Name of Custom Policy above"... Not sure what else to try to get this to work...
here is a like to the document i'm following: URL
Page 68 refers to the "Configuring Sponsor Authentication" for Radius.. it just tell you to add the Radius Server & change the authentication order.
I currently have two AP541N access points. Both are configured for internal access and one unit is configured with a Guest VAP. I want to configure the Guest VAP to redirect to an authentication page so that the user connecting has to log in to get internet access. I'm fairly certain the AP541N doesn't offer this out of the box. I know I can redirect, but what is needed to force a user to authenticate to gain internet access. I want to find out what additional hardware/software I will need in order to create Guest Services of this VAP.
View 1 Replies View RelatedCan use ACS 5.2 as Guest user authentication server?
View 3 Replies View RelatedI installed NGS 2.0.2 for wireless guest user management and authentication. I implement webauth via webauth page on wlc deployed.One Branch with a WLC5508 version 7.0 wireless anchor controller is working on the NGS.But now I integrate next branch with WLC4402 version 6.0.188 and the authentication of users at the new branch gets an error, wrong user/password.
I double checked configuration and user/password but I can't find any configuration error. Also stopping and starting of radius service and reboot of NGS still does not work. I tried to debug the radius via web interface and watched for the loggfile and there is still a reject.I also tried the freeradius command radiusd -X but I got an error when starting the radiusd -X.
1.) How can I figure out, if I will get the correct password from my WLC ? Are there any debug options to see more ? e.g. some cli commands, radiustest utilities or how to get the received password from the chap challenge of the debug ?
2.) I have appended a part from my radius loggfile. How can I find the detailed error in the radius log file? Is it correct that the password in the debug file is empty ? raiuds logg line "[radius-user-auth] expand: %{User-Password} -> "
Can we change the internal web authentication for guest network to use http instead of https?
View 3 Replies View RelatedI have a strange situation on my guest wireless LAN.The guest WLAN is configured as an SSID "GUEST" on Cisco 1142 lightweight APs, with WiSM controller and WLC software version 7.0.230.0.
For simple Internet access using this SSID, we have a web policy, which causes a web page to be displayed when the user opens his/her browser, and on this web page, the user must click on an "Accept" button in order to accept the terms and conditions of use. Once the user accepts, the browser will then go to the web site which the user wishes to open. When using this mode of access, everything is fine.
However, there is also a pre-authentication ACL, which allows certain types of VPN traffic to reach the Internet without the user being required to accept terms and conditions. The ACL allows ESP, IKE (UDP/500), IKE over UDP (UDP/4500), DNS, HTTPS/SSL (TCP/443), DHCP client and server (UDP/67,68).The pre-auth ACL actually works as intended; and the ACL traffic is NOT allowed when the ACL is removed. This is exactly as it should be.
However, when using, for example, a VPN client such as the Cisco VPN client, or the Cisco AnyConnect client, via this guest SSID without user acceptance, the WLAN regularly and predictably stops passing traffic. This is 100% repeatable and predictable; it happens every 300 seconds, or possibly slightly longer. I have only used my PC clock to time it so the timing isn't all that accurate but I'm sure it's within a few seconds.
Given that the problem happens at the same time interval and is constant, I guessed there must be some configuration item which needs to be altered, but I've looked extensively at the controller GUI (we actually use WCS here) and I can't see anything that looks even remotely related to this.
E2000 has the guest account feature. Not sure if all guests shares the same login credentials. I would like to have guests account use seperate logins. Is this feature available? Another thing, I read the manual and it is indicated that only up to 10 maximum guest acccounts is allowed. I am looking for more than 10 - kinda like a hotspot software.
I've been looking everywhere. I've seen hotspot system, ddwrt, chillspot, etc. But it's complicated as firmware needed to be flashed.
I have successfully set up a guest network on my EA4500. Guest laptop associates with guest SSID just fine. Then via IE, it gets prompted for the guest password, which is entered and accepted just fine. At this point guest laptop is on the network.
BUT... at some point the guest laptop will need to reauthenticate (I don't know what the timeout is, but maybe one or two days?). Anyway, it's at this point that IE presents the guest network login page. But now after typing in the password, "enter" or clicking on the button does nothing. It looks like the guest web page doesn't get loaded properly or completely, so the reauthentication can't complete, therefore can't get to the internet. So, while in this state, I've also tried Firefox and Chrome, and same thing, no action when trying to submit the guest password. Tried rebooting guest laptop, and still same problem. Only thing I've found so far that works is to reboot the router. So I'm guessing there's a problem with the guest/web server on the router?? It's a real pain to have to reboot the router every day or two, when I've had other Linksys routers run for months without having to touch them.
I was running CCC 2.1.38 when I first noticed the problem. Since then I've downgraded to Classic 2.0.37, but it seems I still have the same problem. Again, I can connect & authenticate just fine initially, but when reprompted after some period of time, it doesn't work.
I've tried contacting Cisco support, but it looks like I'm at 91 days since purchase and thus outside of my 90-day complimentary support, so they happily provided me with the premium support options just to have the honor of talking with them. Guess I shouldn't have spent so much time trying to figure this out myself.
What's the least expensive way to enable Guest Network authentication in a network with WLC 4404 controllers and no WCS? Management would like guests to register with a valid email address and enter a 'password du jour' to keep unauthenticated users from chewing up bandwith with automatic connections.
View 4 Replies View RelatedAny problems with the guest network on the ea4500 with the cloud firmware? I am losing guest clients after about 24 hours and the re-authentication fails. you enter the guest password and nothing happens until you reboot the router.
View 2 Replies View RelatedIs it possible to allow certain websites to bypass the web authentication pages, so that they do not need to authenticate to get to our own website, but do have to if they wish to go anywhere else?Looking at a 5508 model at the moment
View 4 Replies View RelatedI want to prevent guest from doing peer - peer communication on my Guest (5508) controllers. Is this a feature on the WLC or only by applying an ACL on the router interface?
View 2 Replies View RelatedI need a guest password for 192.168.33.1
View 2 Replies View RelatedWe presently have a guest wireless solution in place using 4400/5508 WLC controllers authenticating guests via a NAC Guest server. This has functioned well for the last year or so, but now our security team has requested that we begin logging guest activity. I already have RADIUS accounting set up on the WLAN configuration pointing to the NGS,I have added the NGS to the syslog set up on the controller (I have tried various syslog levels) but I am not receiving any guest activity info in the reports on the NGS. Any way for getting this data?
View 2 Replies View RelatedWe currently tunnel guests to a 4402 that sits behind our firewall and it's been working well for a few years but I am aware that the 4402 is now EoL so I am exploring alternatives:
We also have several 5508s deployed and I'm wondering if - in any new guest access config - I can allocate one of its free h/w ports to connect to the firewall, even though the 5508 is configured to use LAG.
To put it another way can I configure a new port to a seperate VLAN and not be part of the the LAG'd ports or are you tied to having all ports acting as a group if LAG is switched on?
WLC - 7.2.110.0
ISE - 1.1.1
I'm new to ISE. I want to set up a very basic method for BYOD users to access our wireless network. I've set up an SSID for external Web Auth, where users get redirected to the ISE Guest Portal: [URL]
At that screen, users can enter their Active Directory credentials and login. Although the authentcation shows as successful under Operations -> Authentications, the user is redirected to the device registration page. On that page they see the message "We are unable to determine access privileges in order to access the network. Please contact your administrator." Their device MAC is listed, and they can enter a description but the "Register" button is greyed out.
I'm getting overwhelmed with the amount of documentation available as well as the new terminology. I'm familiar with using Windows RADIUS servers, but ISE is very foreign to me now. Is there any documentation to understand how access requests are processed?
how can i set up a guest access?
View 1 Replies View RelatedAlrighty, a little misdirected here. been reading docs for a little while and experimenting around maybe someone can point me in the right direction, How to you create a Guest Network in IOS Zone Firewall. For some reason Cisco, while using the term DMZ, applies differently on their routers than it does on their ASA's. I know how to do this on ASA's all day long however on the router it is a little different story.
View 5 Replies View RelatedIs it possible to provide wireless guest access over the WAN from another office via the WLC. I have WLC 5508 in a central office and have other remote offices that have one Access Point in each office that are autonomous; I will be converting these to LWAPP. Is it possible to route guest traffic back to the WLC then forward this traffic out to the internet? How would I route this traffic out as well? install a secondary WLC in the DMZ and use anchor points. I only have one WLC
View 7 Replies View RelatedI installed a WLAN with a WLC 2504 and 1140 APs. My network is configured the following way. 10.10.X.X/8. Port 1 on my WLC has the following interfaces management with the ip address 10.10.X.5 and the virtual interface. I have one secure SSID on the management interface. DHCP is done on my Sonicwall firewall. I was advised to create a second interface called AP-Manager and i have the following questions:
1. Do i create a new port or do I create the AP-Manager interface on the same port as my other interfaces?
2. Once i create the new interface of AP-Manager, will my APs migrate over to this interface?
3. Do i need to create the AP-Manager interface or leave all my AP's on the management interface?
4. Second do I need to create a services interface and if yes, on port 1?
I also need to create a guest network that would have the ip scheme of 172.16.X.X and have the guest authicated by level 3 web authication.
1. Do i create my guest interface on port1 or create a new port?
2. DO i need to point my DNS of the interface to the virtual interface.
I'm having problems settting up a Guest NAC server to authenticate administrative users against a ACS 5.x server. In the ACS RADIUS Authentication log, I can see the user authentication is successful.In the AAA Diagnostics log, I can see the following warning:An Access-Request MUST contain either a NAS-IP-Address or a NAS-Identifier or both; Continue processing.
View 2 Replies View RelatedIt's my intention optimize our business WiFi network.Actually we don't have a "Guest" access.Probably WAP321 should be the best solution for us.We will need 3 WAP321 to cover offices area.I have different questions/doubts about Captive Portal functionality.using 3 different WAP321 everyone has the "captive portal" feature, or you can configure only one of the three the feature of "captive portal"?if is possible to configure only one of three the feature of "captive portal", the others WAP321 trusting the authentication?what is the ip address released from the "Captive Portal"?all Guest user have the same username and password?
View 1 Replies View RelatedI am trying to setup a Wireless Network on my WLC that is totaly independent of our internal LAN. Port1 is designated at the .14.0 network and Port2 is the .18.0 network. The 14 network (Port1) will be the guest and 18 network (Port2) the internal wireless.
The issue i am having is nothing is routing to Port1. I have the Guest Wireless set to get DHCP from the WLC and i can get an address but i cant get internet access. I tried configuring a Network Route but it will only let me set the service port as the Gateway and not the IP for Port1.
I am running software version 5.1.151.0 and using this guide as it is the only one i can find. [URL]
Here is a screen shot of my Interface config.
Managed to guest LWA working with ISE for wireless guest portal access? I have Cisco 4400 WLCs running latest 7.0 code and ISE 1.1.2.All guest portal examples seem to be CWA which only works on 7.2 code.Am I without hope getting this working on 7.0 code?
View 3 Replies View Related, I have a requirement by a customer that they will want to monitor the guest wireless access. Currently, we are proposing a Cisco Wireless Controller 5508 together with APs and the setup would be a dedicated VLAN for guest. I am wondering if Cisco ISE together with Cisco MSE would be sufficient?
Stuff to monitor and log are:
1. Guest username (I guess this would be self sponsored)
2. Company name
3. Websites accessed
4. Time, date and duration.
5. Logs are to be kept for 3 months at least.
I recently bought a Cisco SRP527W and I'm trying to setup a second wireless network for guests.
I created a "guest" VLAN and I assigned the "guest" SSID which I have created.
I created a "guest" DHCP server and assigned it to the "guest" VLAN.
The "guest" SSID is set to broadcast and has WPA2 Personal (TKIP+AES) authentication. These are exactly the same settings I have for the "non-guest" WiFi.
However, I can't get my clients to connect to the network. The "guest" WiFi is visible and clients are prompted to enter the password but after that they end up with an APIPA address. When I move the "guest" SSID to VLAN1 (along with all the other networks) then it works absolutely fine.
I was just wondering if I'm simply missing something in the configuration ..
The device is running the latest firmware (1.01.24 (003) September 7, 2011)
DHCP server has DNS Proxy setting enabled and WAN Interface configured as "Default Route" (have basically replicated the same settings as VLAN1)
I am primarely enquiring whether the setup I have explained below is actually possible, and if so then how I can set this up. I know it isn't the easiest configuration and I need to set this up without purchasing any more equipment if at all possible.I have a Cisco SG 300-28 setup with three VLAN's. [code] Default Gateway is 192.168.10.1 (Netgear Router)I have a Wireless network setup (Netgear WMS and 2 WAP's) configured with the TWO VLAN's (1 and 3). These go into ports on the Cisco SG 300-28 which are tagged on both VLAN's. The Business wireless worked fine but the guest network didn't reout out to the internet.After some troubleshooting I realised the reason the guest wasn't working was because there was no route back from the internet to the router.
The router I have isn't really ideal, it is a Netgear DGN2200, but I managed to create a static route to 192.168.30.1 with a metric of 2, with 192,168,10.254 being the hop. Success, the connection worked, the only problem is that now my guest network can see my business network because the business network is using the static route on my router to route back over to the guest network (due to the limitations of this device I can't do anything about that)Guest network can connect to Business VLAN via switch. I am assuming this is because the router is on the Business VLAN and the default gateway is the router. As they are on the same network the Guest network can inevetably see the business server and network.The Business network can get back to the Guest network via the router using my static route I created. The static route is really basic and I can't create a firewall rule on the router to prevent the Business network speaking to guest network because it only has a LAN - WAN firewall and this connection is LAN - LAN.
What I need is...to somehow stop any traffic from the 192.168.30.0 network routing to anything on the 192.168.10.0 network, appart from the router on 192.168.10.1.Is this possible? I have this setup on a number of different site, the only difference is I have a CIsco Security Router on these with the VLAN's configured so I don't have this problem. Because I have a rather limited Netgear DGN2200 I am unable to setup the VLAN's correctly and as such I need to see if I can do this on the switch in any way.
Strange issue that our support staff is seeing on our guest WLAN. I have 2 wlans, 1 is production and authenticates our Domain controllers, this is working fine. The other is a wlan that has restricted access internally, I allow http, https and VPN access out only.
It appears that on the guest wlan, after random amount of time an established VPN connection using Cisco VPN client disconnects. Wireless connectivity doesnt appear to go down, just the vpn connection.
On this guest wlan, I have configured QOS bronze and I read a link where this may be affecting the UDP conversation between VPN client and end point.
We have a 2106 that was configured by a former employee. No one left in the company is qualified to configure it. The wireless guest access used to work fine. We'd configure a guest user account. They would connect to the guest wireless, open a web browser and login. For some reason now there is no prompt for login. People can connect to it and get an IP address, but that's it. No login prompt or anything else from there.User Login Policies was set to 0 and I put it to 8. That didn't do anything. Under Web Auth > Web Login Page it's set to Internal (Default).
View 5 Replies View RelatedI'm looking to implement guest WiFi access with web authentication on one of our 5508 WLC (currently deployed within a sandbox environment), but looking for some assistance. The WLC currently has a single connection from port 1 to the 'Test Site 2' switch. This is a dot1q trunk. On the WLC, the interface (for port 1) is configured as follows: [code] Currently, I have one WLAN configured with the profile name 'Guest Test 1', it's enabled and broadcasting the SSID. Security is L3 only with web authentication configured. The WLAN is configured to use the interface names "guest_wifi".
The issue is that when a client connects to the WLAN, it receives an IP address okay (10.99.254.x address), but doesn't seem to be able to contact the WLC to get the web authentication page. Eventually, the WLC terminates the connection due to an authentication failure.does it sound like I'm taking the correct approach here? The idea is that clients connect to the guest WLAN, which puts them on VLAN 99 and routes traffic through to the ASA and then onto the internet.
I have a 2504 WLC with a 1042 AP and I have it placed on my edge Cisco 3750 switch. I have the management interface of the WLC set on my WAN IP 71.x.x.x subnet range, and I have the WLC doing DHCP duties with a DHCP scope of 192.168.X.0. I have my DNS servers set on external DNS servers out on the Internet.I have two Cisco 3845 Routers on my edge network - one for each ISP with BGP protocol.
Since my native VLAN is 71.x.x.x, I added a sub interface on my main core router and gave it a 192.168.x.1 255.255.255.0 address for the gateway. Also, I added ip prefix-list iBGP seq 10 permit 192.168.x.0/24 le 32 to my main core router. On my secondary ISP router I added ip prefix-list iBGP seq 10 permit 192.168.X.0/24 le 32, and ip prefix-list OUT seq 10 permit 192.168.x.0/24 statements.
I added VLAN 10 to my edge switch and gave it IP 192.168.x.2 255.255.255.0, and the switchports that my core router and my WLC are connected to the edge switch, are in trunk mode with encapsulation dot1q 10. The switchport on my edge switch that the AP is connected to is in switchport access mode.
I can connect to the wifi with a 192.168.x.x IP address on my laptop, but I cannot get any Internet access. Is it possible to have the DHCP scope be in a different subnet than my WAN IP subnet, and allow guests to get to the external Internet only? Do I need to put the WLC somewhere internal on my network i.e. the DMZ and then tunnel the traffic out to the Internet with no Internal network access?