Cisco Routers :: SF300 24p Vlan Tagging Being Stripped?
Feb 13, 2012
I have a sf300 with (2) vlans (1) ] vlan for data and vlan (100) is my voice vlan I have Vlan (100) tagged traffic, and my VoIP pbx as an access port only to vlan (100) all other ports are trunk ports with vlan (100) tagged and vlan (1) untagged traffic. I get no outbound audio on calls I can call out hear them fine they cant hear me. I am wondering if my tagged traffic leaving the phone is being striped and if so were. I have CDP turned off.
View 1 Replies
ADVERTISEMENT
Apr 29, 2013
getting a SF300 to properly route IP between 2 VLANs. I've watched the demo video and performed everything it showed, but I get the most bizarre half-way results. I haven't done anything on Cisco routers in about 15 years, so I'm a little rusty.
We have an office LAN with a cable modem/router for Internet access where the modem/router has IP address 192.168.1.1. We have the usual 24 bit prefix net mask. The SF 300 is connected to this network on port 1.
I have configured port 1 to VLAN 1, interface in Access mode, assigned a static IP address of 192.168.1.36, which is a free address on our office LAN. I have configured port 2 to VLAN 2, interface in Access mode, assigned a static IP address of 192.168.3.1 I put a static route in the modem/router, pointing 192.168.3.0/24 to 192.168.1.36.
I have a PC on 192.168.3.10 attached to port 2.
The SF300 can ping 192.168.3.1, but not 192.168.3.10. 192.168.3.10 can ping 192.168.3.1. It can also ping 192.168.1.1, and can pull up an HTTP router admin page from 192.168.1.1. 192.168.3.1 can be pinged from anywhere on 192.168.1.x, but 192.168.3.10 cannot be pinged from 192.168.1.x. Finally, 192.168.3.10 cannot ping any other addresses on 192.168.1.x except 192.168.1.1, and cannot reach the Internet.
Here's my configuration:
switch6d919d#show runconfig-file-headerswitch6d919dv1.3.0.59 / R750_NIK_1_3_647_260CLI v1.0set system mode router
file SSD indicator encrypted@ssd-control-startssd configssd file passphrase control
[Code].....
View 3 Replies
View Related
May 12, 2011
We are trying to config vlan 10 for data and vlan 20 for voice on the same port - port 1 of swtich SF300-24P to run both data and voice on different vlans.Do I have to add vlan 10 as an untagged vlan to port 1 and add vlan 20 as an tagged vlan to port 1?If I do not want to assign the native vlan 1 to port 1, how can I remove it ? The GUI page - assign VLAN to port does not allow to remove it.Aslo, what mode shall I set up on port 1? General, trunk or access ?
View 18 Replies
View Related
Jul 29, 2012
Unfortunately I do not remember the model and the switch is a couple of hours away without remote access.I have 4 vlans on a procurve switch.
VLAN1 - Network Devices (Server, printers, WAPs)
VLAN100 - Admin (Office workers)
VLAN200 - Teachers
VLAN300 - Students
There is a server doing DHCP. There are 4 ranges of IPs 1 for each VLAN.
The router is on Port 44. VLAN 1, 100, 200, 300 - Tagged
The Server is on Port 46. VLAN 1 - Untagged
The WAPs are on Ports 1, 11, 31 VLAN 1, 100, 200, 300 - Tagged
All other ports are on VLANs 100, 200 or 300 - Untagged
The WAPs all have VLANs 100, 200, 300. Each VLAN on a different SSID.
I have IP helper with the server IP on VLANs 100, 200, 300.
There are IPs from the different subnets on their respective VLANs in the switch.
The gateway for each subnet is on a different subinterface on the router.
The router is a linux box. (Untangle)
The WAPs are not able to talk to the server, therefore no computers on the wireless networks can get an IP.The server can only talk to the router if I change port 44 to untagged.What combination of tagged and untagged ports do I need to make everything talk?
Do I need to put the VLANs on the subinterfaces of the router?
View 1 Replies
View Related
May 18, 2011
I need some assistance in setting up VLAN's (802.1Q) accross two switchs, I want the same 2 vlan's on both switchs, how do i configure them to be connected and pass both vlan's traffic.VLANs from firewall are tagged at 3 and 8.Single port out from the firewall.The first switch is simple enough, port is connect at port 52 and configured from both vlan's then the individual ports are either on one or the other. The question is how do i connect the second switch so that it can also do both vlans. Assume I connect switch1 at port 51 to switch 2 port 52. Do I configure both ports to be on the same VLAN's. or do i setup LAG's.
View 3 Replies
View Related
Aug 19, 2011
I am currently tasked with setting up a network, pretty much from scratch, that requires some fairly hefty VLAN deployment. My hardware on hand (already existed so can't can't change anything easily) 5x ESW-540-48 Switches, 1x3750g switch, 1x2811 router. I don't believe the router should be required as the 3750 is capable of intervlan routing. [code]
Now at one point I actually had the VLAN's *working* in that I could specify an IP address and could ping to and from it! However DHCP wasn't passing despite numerous attempts with DHCP relay and IP-Helper configurations.Also I was having issues with VLAN 1 as the native VLAN, the ESW switches don't allow you to do much with them, as they 'weren't created by the user'. So tried switching that out to VLAN11 also but with very little success there (I had to change the native vlan on all trunks to VLAN 11)All the 10.x.x.x addresses need to be able to communicate with each other.All the ESW switches need to be able to handle their respective VLAN's as well as VLAN 1 (for Printers and wireless access points distributed around the building).
View 16 Replies
View Related
Nov 23, 2011
We are having one HP core switch and VLAN is configured on it. Four Nortel BES1010(24port) switches will be connected to this HP switch. We need to configure the VLAN tagging in the Nortel switches in order to make deices connected to nortel switches can communicate with devices in the VLAN.
View 3 Replies
View Related
Sep 28, 2012
I'm Confused from the fact that Vlan tagging is done at access port and trunk port always gets tagged packets (untill its case of native vlan).But I still believe in other fact which says tagging happen only when a frame hit the trunk port which means trunk port gets untagged frame and tagging is not possible at access port.
Would like to know where actually this tagging happens ?
and also which command we can use to encapsulate 802.1q protocol to access port ? The way we do at trunk port is #switchport trunk encapsulation dot1q Is the above command applicable for access mode also?
View 6 Replies
View Related
Jun 13, 2013
We are trying to replace the CSS between our firewall and DMZ with a BigIP. Among it's other functions, it will act as the router between the firewall and the DMZ. To make this work, I need to assign vlan tags values for the vlans I create on the BigIP box and these must match the tags on the cisco switches (3550's) How do I find this information on the switch?
View 2 Replies
View Related
Oct 25, 2012
we have a base license ASA 5510, and been trying to get ICMP working to check that we're routing and not hitting any NAT translation. We have a VLAN280 setup to ISP for VPN link to remote site and another VLAN281 for internet access for internal users.
Users can browse internet from (name _inside interface e0/1 access port) which is fine. When I do a ping to remote office through the VPN I get a response pinging from VLAN280 name VPN_Link. When I do a ping from name inside interface I don't get a response both are security level 100 with same-security-traffic permit inter-interface configured.
Config:
!
interface Ethernet0/0
speed 100
no nameif
[Code]....
View 11 Replies
View Related
Feb 14, 2012
I rencently bought the E4200v1 router, to be wired together with my WRT610nv2 to form gigabit network for different floor network.However with the recent installation of fiber to home network offered by my local ISP, I would need router that capable for performing vlan tagging (500 for internet & 600 for IPTV).Would like to know if Cisco have any development plan to enable the VLAN option for:-
1. E4200
2. WRT610nv2
At the moment, I'm still stuck with the provider "home-made" router which lacks of Gigabit & dual band wireless.
View 9 Replies
View Related
Oct 30, 2011
Having an issue getting my DMZ vlan working. Running my ASA5505 and i have configured e0/2 for DMZ w/ VLAN ID 3. Connected to my 2716 on port2.Inside e0/1 w/ VLAN ID 1. Connected to my 2716 on port1.
I am trying to get my DMZ Vlan to ports3&4 (LAG1) but when i assign the LAG group to PVID 3 i lose connectivity on VLAN1. I want to send both VLANs to that host because the teamed adaptor is used for Hyper-v Network Switch.
View 17 Replies
View Related
Jul 5, 2012
I have a 2960 switch connected to another. The I need to verify that vlan0010 on one switch is forwarding tagged traffic between the other switch it is hooked up to through the Gi0/1 port. How do I verify this? I have a server that's multihomed (Broadcom) on the other side an it is supposed to be on this vlan with one of it's network interfaces. We had a pwer outage and now it cannot communicate on this vlan. However, everything else on the vlan can reach all the other nodes accept this server in the front of my building. All the devices in the same room are linked to the same switch which has one port (fa0/17) on vlan0010 and can ping eachother just fine. The server is hooked to port 24 on my server room switch and Gigabit port one goes to a fiber converter all the way to the back. It then gets converted from fiber to cat5e again and links into the switch (2960) in the backroom.
View 5 Replies
View Related
Mar 18, 2012
I'm a little stuck with a 4400 7.0.220.0 + RAP 1550 + MAP 1260 Ethernet bridging issue. I'm using the VLAN tagging functionality and I'm finding that periodically a VLAN that I've tagged on the MAP will deregister from the backhaul and stop passing traffic. If I go into the Mesh tab on the MAP, select the wired interface, remove the VLAN from the list of tagged VLAN IDs and then add it right back to the list, its starts passing traffic again
View 2 Replies
View Related
Dec 13, 2012
We have a problem with CDP packets on sent by our Cisco 6509's. Unlike our other Cisco switches (4948G, 5020, etc.), the 6509 tags administrative traffic on the native vlan. As a result the CDP packets are sent with an 802.1Q header with a tag of 1. The other switches send the CDP packets untagged on the native vlan. This causes problems because we have non-Cisco devices in our lab that also receive and send CDP, but they do not process the packets that are tagged by the 6509. They see the packets from the 4948 and 5020 just fine.
How can I disable the administrative native vlan tagging on the 6509? Here is the current setup:
nwkdev-6509-1#show vlan dot1q tag native
dot1q native vlan tagging is disabled globally
nwkdev-6509-1#show interfaces gigabitEthernet 1/9/1 switchport
[Code].....
View 13 Replies
View Related
Jan 14, 2013
I've been experimenting with the 'vlan dot1q tag native' command on a switch and it seems as though tagging the native vlan breaks vty access to my access point.With the 'vlan dot1q tag native' commnand applied, I lose management connectivity to the AP with 'no vlan dot1q tag native' applied, connectivity is restored. Why is this? Is it safe to say that one can access the AP via vty lines using ONLY untagged packets?
SWITCH
Model: WS-C3560G-24PS
Code: c3560-advipservicesk9-mz.122-46.SE
--Abbreviated CONF
vlan dot1q tag native
[code]....
View 14 Replies
View Related
Oct 17, 2012
In my network I got 3 SF300 24 p switches. I managed vlan 10 for data and it is also a native vlan and vlan 20 for voice ,1st switch is the core switch and im having a problem in connecting them ?
View 7 Replies
View Related
Jan 2, 2013
my new Cisco SF300-48. I want to create 2 vlan (vlan 1 & vlan 2). The switch is set at layer 2. example : vlan 1 (port 1, 2, 3) , vlan 2 (port 4, 5, 6) vlan 1 can communicate each other (port 1, 2, 3) and vlan 2 can communicate each other (port 4, 5, 6)But vlan 1 cannot communicate with vlan 2.
View 4 Replies
View Related
Apr 22, 2011
I had made a DHCP server that had many scope:
1- scope: 192.168.1.208/28
2- scope: 192.168.1.224/28
3- scope: 192.168.16.0/24
[Code]....
How to condig SF300-24 to vlan 2 vlan 3 can get IP address from DHCP server in VLan 4?
View 14 Replies
View Related
Jan 2, 2012
I have a SF300 24 P and Iam trying to configure a voice vlan this is what I have done so far and it doesnt work.
1. create vlan 30 for voice traffic and enable it
2. Telephony OUI add my mac address for allworx phones
3. Port to VLAN add 30 has tagged, port to vlan 1 untagged
4. Vlan to port I try to add 30 and get this error (Port e15 is candidate in voice Vlan 30 and cant be configured as static member in the vlan.
5. Under Discovery LLDP, LLDP MED port Setting Enable MED status, then all other options to yes
In my LLDP neighbor information all my phones are there and says under port ID 0 ( my phones support LLDP and CDP)
View 1 Replies
View Related
Oct 22, 2012
I have a Cisco SF300-24P deployed at a customer prem running only a couple VLAN's - 1 customer related and 1 for management. Recently the customer inquired about changing his connection to Q-in-Q. I have changed the interface type to customer but then it selects vlan 4095 as the vlan associated to that port. How do I change that vlan or by default is that the only vlan I can use? Currently the customer is using vlan 904 and would like to continue to use that vlan in the Q-in-Q config.
View 1 Replies
View Related
Dec 12, 2012
I bought a sf300 48 and made 4 vlans.
How can I restrict the mac address of device can be connect each vlan ? I just want allow the macs for vlan, dont need join the pc to a vlan.
View 8 Replies
View Related
Oct 12, 2011
I got question about Cisco SF300-24P- is it possible to have management vlan in other vlan than in default vlan?I have default vlan 10 and voice vlan 20, I need to reach switch through voice vlan so I need to set up, interface vlan 20 with ip address. I ask these, because in gui, under Management Interface, IPv4 interface,under Management VLAN, I can only choose vlan 10, which is my default vlan, I dont have option to set ,up, in this case, vlan 20 as management vlan.
View 2 Replies
View Related
Sep 9, 2012
I have a SF 300-24 24-Port 10/100 Managed Switch and I am trying to set some VLANs. The image below shows how I want it to be setup:Since the remote site goes through the Internet, making port 20 an 802.1Q trunk over the two VLANs will give WAN connectivity to VPN/E-mail.I've tried all sort of settings [ see attachments] but can't get it work.
View 5 Replies
View Related
Oct 20, 2012
i have a small network with Polycom phones connected to the sf300 switch and have the pc's daisy chained via the second switch port on each phone. i have the pc traffic running on the default vlan 1 and the voice traffic running on the voice vlan 100. can i do bandwidth management on a vlan/port basis or is that not necessary. i want to ensure that the voice traffic is never impacted by the pc traffic on the same cable.
View 2 Replies
View Related
Feb 12, 2012
I have a sf300 with (2) vlans (1) ] vlan for data and vlan (100) is my voice vlan I have Vlan (100) tagged traffic, and my VoIP pbx as an access port only to vlan (100) all other ports are trunk ports with vlan (100) tagged and vlan (1) untagged traffic. I get no outbound audio on calls I can call out hear them fine they cant hear me. I am wondering if my tagged traffic leaving the phone is being striped and if so were. I have CDP turned off.
View 1 Replies
View Related
Apr 17, 2013
i have a asa5505 and sf300-48,in the sf300 have ip defult-gateway 192.168.1.93 and have internet in vlan2 but vlan 3 not work. ping from "vlan3" to "vlan2" its ok.
View 5 Replies
View Related
Feb 26, 2013
Region : Malaysia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : Maxis
I bought the TL-WDR4300 almost 6 months ago using it on my TM Streamyx broadband service, it worked perfectly and this is indeed a very good product very reasonably priced too Kudos to TP-Link. The thing is shortly after purchasing it, I moved to Maxis Home Fibre Internet (more bandwidth). Following the ISP change the router has since went back into the box and had been there for 5 months now. This is because without the VLAN tagging feature or a Maxis mode, it is currently incompatible with Maxis Home Fibre Internet and will stay that way.I understand this is by no mean TP-Link's fault but I and many other WDR4300 owners on Maxis, if TP-Link could look into ENABLING VLAN TAGGING FEATURE/MAXIS MODE on this device. This I am sure would work with TP-Link sales as there are not many routers out there with this feature set and price range that could work with Maxis Home Fibre Internet.
View 1 Replies
View Related
Mar 16, 2011
difference between mirrored strips vs stripped mirrors
View 2 Replies
View Related
Oct 6, 2011
now we have 2 switches: SF300-24..on one SF300-24 we config it at layer 3 mode with VLAN configuration same as following [code] And we use port 26 on 2 switches SF300-24 is trunk mode then we connect both SF300-24 switches.But on SF300-24 layer 2 cann't inderstand VLAN from Sf300-24 layer 3..How to config VLAN on 2 switches SF300-24 Layer 3 and SF300-24 layer 2?
View 2 Replies
View Related
Jan 12, 2013
How do I submit an RFE (Request For Enhancement) to the Cisco SBR team to encourage them to implement the missing support for VLAN to VLAN firewall rules that was available in the RVS4000 (See [URL]) and that was supposedly added to a beta release of the RV220W firmware (See [URL])?
View 1 Replies
View Related
Jan 20, 2011
I have a Netgear GSM7248R switch with 5 different Vlans including th management Vlan. Each of the vlans are connected to my layer 3 switch for routing. I want to access the management vlan form any of my Vlans so my layer two switch can be detected by my snmp manager.
View 3 Replies
View Related
Aug 22, 2012
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies
View Related
