Cisco Switches :: SG300 Is Dropping Packets?

Apr 10, 2012

We have a customer who we sent to Cisco to replace some aging Dell switches. They purchased 5 SG300-52’s for 2 different networks. Their production LAN has 2 “live” switches and 1 spare. The 2nd, a development LAN has 1 switch and 1 spare. Their primary production SG300-52 has GE1-8 VLAN’d off as VLAN2 for public IPs. The untrusted (WAN) interfaces of 2 x ASA-5510’s, 1 x ASA-5505, and 2 x RV082 v2’s are connected to GE2-6. GE1 is the uplink to the co-location center’s Cisco switches. GE7 & 8 are spare ports. Each SG and device port is hard coded for 100/Full.
 
One of the ASA-5510’s and the ASA-5505 maintain a site-to-site VPN (the development LAN used to be in a different facility hence the VPN). Recently the developers have stated the performance is horrible. I noticed ping traffic loss from PCs on the dev side to servers on the production side in the order of 20-30%. I assumed it was a VPN issue so I opened a ticket with Enterprise TAC (all the ASAs and the SGs have either SmartNet or extended support contracts). TAC determined the problem happened even if you ping from inside the ASA to the untrusted side of the other ASA thus eliminating the VPN as the culprit.
 
The 2nd ASA-5510 has the AIP module and was not even live until this weekend. Turning it up and giving it a basic config returned the same results. #ping x.x.x.x repeat 100 will drop 20-40 packets. I have no security enabled on the SGs and even tried using the spare SG300-52 this weekend in place of their primary with the same result. I’m to the point of returning one of the Dell switches to production, but this cannot be a good sign. I’m also a bit frustrated that I’ve yet to figure out how to get Cisco Enterprise to speak with Cisco Small Business on this. The customer has over $10k invested in Cisco equipment and Cisco isn’t jumping in to figure this out.
 
The latest rep wants a packet capture from the SG300’s VLAN2 but there are no PCs there to do this with and the manual doesn’t even talk about doing this. How we can do this as well as get the 2 divisions working together to fix this? BTW, the RV082’s exhibit the SAME exact problem. I can ping from ANY device on VLAN2 to any other device and drop packets. Copying a simple 1MB file over the VPN can take minutes where it should take 1 second. I can reproduce this for 24/7.

View 8 Replies


ADVERTISEMENT

Cisco Switching/Routing :: 3750X Switches Dropping Packets On Uplink Interface?

May 9, 2013

We have a remote site that is using 3750X switches as layer 2 switches back to our home site.  The uplink port is showing dropped packets but the utilization on the link is never about 10%.  We have a 100Mb circuit to this site.  Our speed tests and iperf tests are not showing any issues that we can see.  However the port is still droping packets.  It is not dropping at a high rate but they are dropping.          
  
switch#sh platform port-asic stats drop gi1/1/4
  Interface Gi1/1/4 TxQueue Drop Statistics    Queue 0      Weight 0 Frames 0      Weight 1 Frames 0      Weight 2 Frames 0    Queue 1      Weight 0 Frames 52876      Weight 1 Frames 2      Weight 2 Frames 0    Queue 2      Weight 0 Frames 0      Weight 1 Frames 0      Weight 2 Frames 0    Queue 3      Weight 0 Frames 0      Weight 1 Frames 0      Weight 2 Frames 1330874    Queue 4      Weight 0 Frames 0      Weight 1 Frames 0      Weight 2 Frames 0    Queue 5      Weight 0 Frames 0      Weight 1 Frames 0      Weight 2 Frames 0    Queue 6      Weight 0 Frames 0      Weight 1 Frames 0      Weight 2 Frames 0    Queue 7      Weight 0 Frames 0      Weight 1 Frames 0      Weight 2 Frames 0switch#
         
Is there a way to capture these dropped packets to see what they are?  We do have VOIP phones at the site and are using Qos.

View 5 Replies View Related

Cisco Switches :: SG300-28 GUI Different Than Online SG300-48 Simulator

Aug 29, 2011

These are our first switches and seems like GUI is lot different than the online. Out intervlan routing is o not working. I am absolutely sure that I setup the switch in L3 mode since it allows me to create mutiple interfaces. I am hoping that this GUI issue is related to interVLAN routing.
 
Below is the blog I started for InterVlan issue [URL]
 
This is the link for online simulator and what I see in its IP tab. I know this switch is not SG300. [URL]
 
This is what I see on our switch.
 
Our switch version
switchd64684#show version                                                                                                                                              
SW version    1.1.0.73 ( date  19-Jun-2011 time  18:10:49 )
Boot version    1.0.0.4 ( date  08-Apr-2010 time  16:37:57 )
HW version    V01

View 1 Replies View Related

Cisco Switches :: SG300-28P And SG300-52 Web Managing - Fans

May 26, 2011

1) I have a Cisco SG300-28P. I plan to add a SG300-52. Would it be possible to manage the new switch through the SG300-28P web browser ?

2) There are 2 fans in the POE model SG300-28P. How many fans are they in the non POE switch SG300-52 ?

View 2 Replies View Related

Cisco Switching/Routing :: SG300 - Session Starts With Two SYN ACK Packets?

Apr 20, 2012

I am having trouble with my Cisco SG300 switch big time. I have two servers with IP addresses 10.17.0.11 and 10.17.0.29 sitting on the same switch which is a Cisco SG300. I initiate a file transfer from 10.17.0.11 to 10.17.0.29. I could see lots of Dup Acks and retransmissions which means something is wrong in the connection. Further, I could see the session initiation a bit bizarre. I could see two SYN packets sent from 10.17.0.11 to 10.17.0.29 and also two SYN ACK packets returned by 10.17.0.29. The switch forms part of a network but since both the servers are sitting on the same switch I suppose the rest of the network doesn't come into play when one server talks to the other.
 
See also the number of Dup Acks and retransmissions. The two switch ports connecting the servers have speed and duplex set to auto negotiate, flow control is enabled. What could cause this sort of problem?Could it be any setting on the switch or the servers' NICs?Or could it be a bad switch that causes this?

View 4 Replies View Related

Cisco Switches :: SG300-28 Uplink To Another SG300-28?

Feb 8, 2012

Can I connect a single Cat5e cable between two SG300-28 and link them?  If so what must I configure?

View 1 Replies View Related

Cisco Switches :: Difference Between SG300-28P And SG300-52

Jul 25, 2012

I have SG300-28P that I am using as layer-3 switch. Recently I ran in to SG300-52 switch and even though loading same firmware doesn't give me option to do layer-3 switching. For SG-300 I see options in GUI to create vlan interfaces under IP information section, while SG300-52 has IP information option only under the management section.let me know if these are 2 different hardware types and L3 is not possible on SG300-52. If its possible to enable L3 switching on SG300-52?

View 2 Replies View Related

Cisco WAN :: 3945e Udp Packets Are Dropping

Dec 13, 2012

I have a NAT setup. Some of my udp packets are dropping. How to find more about the NAT to find whether it missed anything or not. the router is 3945e. [code]

View 3 Replies View Related

Cisco VPN :: VPN To Juniper ISG 1000 Dropping Packets

Aug 1, 2012

I have ASA 5510 with 8.4 connected to ISG 1000, when traffic is passing the VPN tunnel is working fine, when the traffic stops, ASA will drop the packet but the VPN tunnel on ISG still up .When new traffic started from ISG side, it will drop, as the tunnel is not up on ASA side.

View 2 Replies View Related

Cisco Firewall :: ASA5505 Dropping Packets

Apr 30, 2013

I am  having an issue where the ASA is dropping packets on the vlan  interfaces. I have it as a dedicated router/firewall for a 100mb connection .
 
Vlan1 is the internal networkVlan2 is the network to cable modem
 
Eth 0/1 is connected to a 2960G switch with hard coded 100mb Full  Duplex at each end, this is the inside interface. Eth 0/0 is the  connection to the cable modem, this is the outside interface, set at  auto at both ends.
 
Im getting on the vlans eg. 51253 packets dropped however network  traffic isnt impacted and everything runs fine, as well as 46532 switch  ingress policy drops.
 
Example;
 
ciscoasa# sh int vlan1Interface Vlan1 "inside", is up, line protocol is up Hardware is EtherSVI, BW 100 Mbps, DLY 100 usec MAC address 70ca.9b36.ab80, MTU 1500 IP address 10.x.x.x, subnet mask 255.255.255.0 Traffic Statistics for "inside": 43250588

[Code]......

View 1 Replies View Related

Cisco WAN :: 800 Router Dropping SMTP Packets

May 29, 2012

We have a cisco 800 series router between the internal network and the WAN. the problem is we are unable to receive some of our mail due to dropped packets by our router. the conversation between the two servers stops at the point were our server responds with the command 250 2.1.5 user@mydomain.com | 354 Start mail input; end with . i was able to trace the packet, using Packet Export, on the internal interface but not on the external interface. Also i have noticed that the external interface has about 160,000 unknown protocol drops while the internal interface has 0.

Is there anyway to find out way the external interface is dropping the packets.

View 4 Replies View Related

Cisco Firewall :: ASA 8.2.4(4) Seems To Be Dropping Valid TCP SYN Packets?

Feb 28, 2012

We have a setup with a MS-TMG - ASA (8.2.4(4) in routing mode) - (internal) Router - FWSM - Router - Exchange with NLB.  We have now the problem that IMAPS is not really working through this setup. It works from internal (without ASA and TMG inbetween), but not reliably through the internet. There is a rule on the ASA which permits the ports from the TMG to the Exchange NLB address.We opened a case with Microsoft and they told us that not all tcp-syn packets are received by the Exchange server which were sent by the TMG.Thus I sniffed on the ASA with a packet capture and indeed, a lot of syn packets were on the interface to the TMG, but not anymore on the interface to the internal router.This ASA also filters all other internet<->company traffic, so there's a lot of stuff running.
 
Maybe it's dropped in the ASP, or is the capture maybe not valid?Here the show asp drop:

ASA01-Internet# sh asp drop
Frame drop:  Invalid TCP Length (invalid-tcp-hdr-length)                                  1  Reverse-path verify failed (rpf-violated)                                  319  Flow is denied by configured rule (acl-drop)                            477077  First TCP packet not SYN (tcp-not-syn)                                   10212  TCP data send after FIN (tcp-data-past-fin)                                 41  TCP failed 3 way handshake (tcp-3whs-failed)                               824  TCP RST/FIN out of order (tcp-rstfin-ooo)                                 1419  TCP SEQ in SYN/SYNACK invalid (tcp-seq-syn-diff)                             6  TCP SYNACK on established conn (tcp-synack-ooo)                              1  TCP packet SEQ past window (tcp-seq-past-win)                              821  TCP invalid ACK

[code]....

View 9 Replies View Related

Cisco Routers :: RV082 Dropping Packets?

Feb 14, 2013

It appears we might have an issue with our RV082 (v4.2.1.02) dropping packets during the teardown of many TCP conversations.  I have attached two packet captures of what I believe is the same conversation.  One is from outside the router (Wireshark using an Ethernet Tap) and the other is from the client inside the router (SLES11SP2 running TCPDump).  These are both very small captures 9 packets and 18 packets and I'm hoping it will identify the problem.
 
It appears that the RV082 is prematurely closing the natted port used to communicate with the host outside the network.  The host sends a FIN, ACK packet, to which the client responds with an ACK,  However, when the client then sends his FIN,ACK sequence, it never makes it outside the router.  The client sends a total of 9 FIN,ACKs trying to contact the outside server, but none of those appear to make it through the router.
 
Is the router slamming the door prematurely?  (I've been fighting with this problem for 3 weeks now!)
 
Inside Capture:
----------------------
No.     Time                       Source                Destination           Protocol Length Info
1 2013-02-13 19:32:37.827942 192.168.1.45          38.113.116.214        TCP      76     35975 > http [SYN] Seq=0 Win=14600 Len=0 MSS=1460 SACK_PERM=1 TSval=635644783 TSecr=0 WS=128

[Code].....

View 19 Replies View Related

Cisco VPN :: Srp527 VPN Tunnel Dropping Packets Intermittently

Dec 12, 2012

We have a Cisco ASA and recently purchased a cisco small business srp527 router.  It is connected to our ADSL2 connection and is working fine.  I have configured the device with an ipsec tunnel using an ike profile and the tunnel is created successfully with packets traversing the tunnel.  However packets are being dropped intermittently, with no cause.  The link is currently not being utilised, there is no load on the network however when I ping Google and any address subject to the rules of the tunnel i notice that a single packet is dropped every now and then.

View 0 Replies View Related

Cisco WAN :: 1811- MTU 1500 - Router Dropping Certain Packets

Dec 15, 2011

I seem to be having an issue where certain very packets are being dropped/lost by my office router. The reproducible situation is, when I attempt a DNS zone transfer from my linux bind DNS server (A.A.A.A) to any server on my network behind NAT (Y.Y.Y.Y) the first packet (Seq 1) of the response is lost. The client making the query asks for first packet (Seq 1) to be resent, and the DNS server attempts to resend it repeatedly, but those are lost too.

View 10 Replies View Related

Cisco Switching/Routing :: Why C2960 Is Dropping Packets

Dec 26, 2012

We have a customer who uses about 20 x c2960's switches for access layer and 2 x c3560e for distribution layer. C2960's uses C2960-LANLITEK9-M , Version 12.2(58)SE1. Everything was working fine. Now we got information, that sometimes there are problems with connectivity. Customer tries to reach internet.
 
SW11#sh int fa0/18       
FastEthernet0/18 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is e8ba.806a.4412 (bia e8ba.806a.4412)

[Code].....

View 7 Replies View Related

Cisco WAN :: Dropping Scavenger Packets On ASR 9000 During Congestion

Aug 6, 2012

I am trying to find a solution using modular QOS when there is congestion in circuit we drop packets with WRED which are marked with a DSCP value of say AF21. I can drop those traffic completely in case of congestion.  I was thinking to allocate 100% bandiwth to rest of the traffic.

View 1 Replies View Related

Cisco Firewall :: 871 - Default Class Map Is Dropping All Packets

Aug 21, 2012

I have a Cisco 871 router that used to have Access list based security. now I am trying the ZBFW for the first time.  I thought I had a pretty good program until I found all my traffic was getting dropped. This is my first stab at ZBFWs and I am a bit confused esp with the default class part.
 
The router is for my house and thus also has to have priority for gaming. I will add the gaming and voice QOS once I get it working,
 
Guest VLAN has access to 2 IP's in Data for printing. Cisco871#sh run

Building configuration...
  
Current configuration : 8005 bytes
!
version 12.4
no service pad

[Code].....

View 1 Replies View Related

D-Link DIR-655 :: Dropping Packets While Gaming On Computer

Mar 27, 2012

I bought a DIR-655 a less than a year ago on amazon, and it was working great up until about 4 weeks ago. Ive noticed that it has been dropping alot of packets while I am gaming on my computer. I would run about 95-98 ping usually and now it jitters every 5-10 mins or so from 95-98 to up to 500. It is really troublesome during games and I dont know what to do. Ive tried disabling QoS and still nothing. I run on wireless G and N with auto 20/40 mhz. Standard WPA(personal) and it was running absolutely great until now. I know its the wireless because I have hardwired it into my laptop, both from the router and just the modem itself with no problems whatsoever. I dont know what to do about it.

View 3 Replies View Related

Cisco Firewall :: ASA5540 Dropping Packets On Large FTP Transfer

May 23, 2011

I am attempting to FTP to a remote site through a IPSEC tunnel.When I am transfering large files the ASA5540 is showing syslog errors stating "connection timeout".  What I think is happening is after about 1 hour the firewall is closing the connection control port for the FTP session and neither end is notified so eventually the transfer is stopped.What do I need to modify in the FW to accommodate these larger files?

View 1 Replies View Related

Cisco Application :: ACE Module A2(3.5) Is Dropping Packets And Closing Connection

Jul 26, 2012

I have a ACE module A2(3.5) installed, I am having a connectivity problem between two servers in my network. I have captured some traffic on different points in my network and from capture it seems like the problem is with this ACE module or somehow it is closing the connection.

View 6 Replies View Related

Cisco Firewall :: 5510 Inspect SIP Dropping Request Message Packets

Mar 17, 2011

I have 2 ASA 5510 firewalls at 2 different sites. Both running on version 8.0.4. Users are using an Instant Messaging type of application provided by a local telco here which is able to send and receive SMS using SIP (from the packet capture that I've done).
 
When users use the IM in site A, they are able to send and receive text messages via the IM from behind the firewall. However, when the users are in site B, users are able to send out text messages but not able to receive them.
 
I noticed that when I remove "inspect sip" from site-B's global policy map, users from site-B can successfully receive text messages. I have confirmed that it is the firewall that drops the packets as I have captured the inside and outside interfaces of site-B's ASA and I can see the incoming sip "request: MESSAGE" packet on the outside interface but I do not see the packet exiting the inside interface.
 
I have cross check both firewall configurations, and I do not see anything suspicious commands relating to sip that might cause this issue. Is there any command to troubleshoot why the sip inspection is dropping the sip packets on site-B?

View 15 Replies View Related

Linksys Wireless Router :: E3000 Dropping Packets On Any Channel But 1

Jul 24, 2012

My E3000 has about 60% packet loss if the channel selected is anything other than 1.  I can't enable 5GHz or even 40mhz 2.4GHz channels without dropping 60% packets.

View 9 Replies View Related

Cisco Switching/Routing :: 3750v2 DHCP Snooping Not Working Dropping Packets

Jan 9, 2013

I recently installed DHCP snooping on a 3750v2 switch (Version 12.2(55)SE4) and configured the uplink(Po2) as a trusted port. The problem is that clients cannot receive an IP address. When I disable DHCP snooping it is working properly. DHCP snooping is configured correctly but I don't have an idea how to resolve it. [code]I tested the solution on the same kind of hardware switch and firmware and it worked out fine. What is causing the clients not to receive an IP address from the DHCP server?

View 10 Replies View Related

Cisco WAN :: 3750 And 4507 / 1Gbps Link / Sweep Ping Dropping Packets?

Dec 29, 2010

We are testing a new 1Gbps WAN circuit between 2 sites. We have cisco 3750 and 4507 on each end. Every time we run extended ping sweep ranging from 36 to 18024 bytes the packets are being dropped randomly once the size goes above 1500 bytes. Our ISP claims Demark to Demark test are clean and they don't want to acknowledge the problem, they blame our switches. To prove the problem is not on our end we've put different switches at each end, still facing the same issue. Ping success rate is around 98 to 99 percent.

View 11 Replies View Related

Linksys Wireless Router :: WRT120n Dropping Incoming Fragmented IP Packets?

Oct 13, 2011

I am trying to use my WRT120n as access device  for an IP Centrex service using SIP protocol. My SIP phone is located right behind the router.My problem is sometimes the router is dropping incoming calls because signalling packets are fragmented at IP level. So I cannot receive those calls.Is there a way to enable the router to accept these packets?

View 9 Replies View Related

Cisco Switches :: Replacing 3COM 4500 Switches With SG300-52?

Nov 21, 2011

I'm replacing 2 3COM 4500 Swithes with the SG300-52 Cisco switch. We have 3 VLANs, 10, 20, 100. The switch is set for Layer 3 and I have setup DHCP relay. what settings i should set on the Cisco for the following setups:
 
3COM Setup
#
interface GigabitEthernet1/0/1

[Code].....

View 2 Replies View Related

Cisco Switches :: SG300 Switches Have Poor Performance In Layer 3?

Jan 1, 2013

We have several of the SG300 Serices switches. We use them to route VLAN traffic to Remote Offices, Internet Connections, and WiFi Access Points.In one remote office we have a SG300-10 setup to route the HQ Network and the remote Office Subnet. The SG300 is Connected to HQ via Fiber and has multiple Tagged VLANs on it. If I do speed tests over the Fiber Link on the Incoming Tagged Netwotk I get Decent performance, 80Mbs. If I switch to a networtk that is not priginating from HQ, and have the SG300-10 route packet, I get dismal performance. 15-20Mbs.
 
I Fireded up a New SG300-28P FW v1.2.7.76. Added a the HQ VLAN 101 and new VLAN 1025 . Mapped some Tagged and untagged ports for each.  Switch was connected to HQ Network as untagged VLAN 101.  I put a laptop on an Untagged VLAN 101 port. Ran some tests, cam back with 750-850Mbs. Great.  Put the same laptop on a Tagged 101 Port, Configured the NIC for Tagged VLAN 101, Same test, same Speeds, 750-850Mbs.I then  Configured laptop for Tagged VLAN 1025. Connected to tagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!
 
I then  Configured laptop for Untagged VLAN 1025. Connected to unagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!It was only the Laptop and the Connection to the HQ net on the SG300-28P. Why is the performance of this unit soooooo poor when it needs to route?Other Switches have FW v1.0.0.27 or FW v1.1.2.0. They have Similar speed issues. All Configured for Layer 3.

View 10 Replies View Related

Cisco Switches :: SG300 Switches Can Be Used With Microsoft NLB In Multicast Mode

Dec 18, 2011

does the SG300 switches can be used with Microsoft NLB in Multicast mode?I know on traditional Catalyst switches you can statically "map" IP's to mac's and then to multiple ports but this doesn't seem to work correctly on the SG switches - it gives an error about the mac not being not Unicast?

View 2 Replies View Related

Cisco Switches :: VLAN Management Via SNMP On SG300-10 Switches

Aug 7, 2011

Any snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.

View 8 Replies View Related

Cisco Switches :: Multiple VLANS And SG300-28P Switches Setup?

Aug 20, 2012

I'm going to have several SG300-28P switches to setup.  I'll need to create multiple vlans for data, voice, and wireless traffic.  I have the following questions in setting up this configuration:
 
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice 
 
1) For managing the switches via IP, will LAN1 be the default management network?  Should I create a seperate VLAN for managing the switches?
 
2) For uplinking the switches together, I plan to trunk a port to connect the switches together.  What's the configuration on the trunk port to forward all vlans from one switch to another?
 
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC.  The phone supports tagging for the PC and the VoIP traffic.  For example on port 10, would VLAN 100 and 300 be set to tagged?

View 3 Replies View Related

Cisco Switches :: SG300-52 Multiple Lags Between Switches?

Jan 19, 2012

I'm having alot of trouble trying to connect more that one LAG between two SG300-52 switches.Basically i have configured both switches with the same vlans. For 2 of the vlans i would like to connect them together between the two switches using LAG. Switch1 has Vlan 5 (ports 1-12) & Vlan 10 (Ports 25-36) with LAG configured on ports 1-2 and ports 25-26. I have setup the second switch identical to the first. But when i connect the LAG's there is no connectivty. If i disconnect one LAG the other starts working.Can you only have i interconnect LAG between switches?

View 1 Replies View Related

Cisco Switches :: How To Configure Two Links Between Switches SG300

Apr 22, 2012

I have two SG300 serie switches and two Gigabit connection between them. How do I configured these two links to work toghether like a one 2 Gigabit channel?

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved