Cisco Switching/Routing :: 2960 - Manual Ip Binding In DHCP
Nov 27, 2011
WE HAVE cISCO 2960 SWITCHES. this switch acts as a dhcp server for the hosts connected to it. Provided mac based binding to the hosts, with enabled dhcp snooping and IP source guard per interface.' I have a problem with single host couldnt get an ip from dhcp as he binded based on mac: manualip. Here is my config: We have a VLAN99, 70 hosts connected should get an ip based on mac
switch(2960<config>interface vlan99
# ip address 10.10.14.2 255.255.255.0(code)
The above host amit (10.10.14.31 swhould get this ip bindded with mac) but hez not getting manual ip i.e 10.10.14.31, but if an ip excluded from the dhcp free, he can get that ip i.e automatic ip . every other host are getting the ips as binded in the pool manual ip. Checked with
**sh mac-address table dynamic vlan 99 ()
**clear ip dhcp binding * or 10.10.14.31
** clear ip dhcp snooping binding
*** clear ip dhcp conflict *
Tried to change pool names. All these troubleshoot couldn't make me success in providing amit an manual ip.
View 10 Replies
ADVERTISEMENT
Feb 8, 2013
I am trying to bind Mac address manually to IP in Cisco 881 router so that if user wants to change the IP address also they should get the same IP.
I have configured as below but it is not working.
ip dhcp pool Test
host 192.168.0.10 255.255.255.0
hardware-address xxxx.xxxx.xxxx.xxxx
this IP was excluded from dhcp range
ip dhcp excluded-address 192.168.0.10
View 11 Replies
View Related
Nov 8, 2011
I am looking for a way to bind between a switch interface (cat 3750X) and a DHCP server reply.The switch can operate as the DHCP server .a PC connected to interface Gi 1/0/1 will lways get IP address 10.0.0.1 because it is connected to interface Gi 1/0/1, a PC connected to interface Gi 1/0/5 will lways get IP address 10.0.0.5 because it is connected to interface Gi 1/0/5 and so on... (no matter the source MAC address who sends the DHCP request).
View 8 Replies
View Related
Sep 14, 2010
I've configured ip dhcp snooping on several vlans I want to monitor and the binding table doesn't seem to be building.eature DHCP is on, global ip dhcp snooping is enabled, VLAN snooping is enabled on the vlan's I want to monitor and my trusted interfaces are also configured. Alas no binding entries in the table! 7K is running 4.2(6).
View 1 Replies
View Related
Mar 5, 2012
Facing some DHCP issue. I got my laptop directly connected with Cisco 2960 switch. However it is not getting valid IP.
View 1 Replies
View Related
Oct 21, 2011
I did the DHCP configuration for my CISCO 2960 switch but the clients are still not able to get the IPs.see the configuration below.
(config)#ip dhcp database cisco.com
(config)#pool test
(config-if)#client client-id vlan 500
(config-if)#ip dhcp snooping trust
View 1 Replies
View Related
Jan 3, 2012
I want to implement port-based and MAC-based in these two switches: 2960 & 3560 (both of them have this IOS version: 12.2(55)SE1). And I haven't found a way to implement both of them at the same time. This is what I got:
ip dhcp use subscriber-id client-id
ip dhcp subscriber-id interface-name
ip dhcp excluded-address 192.168.0.0 192.168.0.2
ip dhcp excluded-address 192.168.0.251 192.168.0.255
[code]....
With this configuration I can use port-based, but not MAC based. If I remove the first two lines and change the last line for this one:
address 192.168.0.7 client-id 0112.ae1d.af58.60
Then, the computer with that MAC address got the correct IP, but then the port-based doesn't work. Also, I got this line in the interface what I want to use MAC-based:
ip dhcp server use subscriber-id client-id
View 3 Replies
View Related
Apr 17, 2012
I have a new catalyst 2960,and i want to enable DHCP SNOOPING,but,it doesn't work,the server is stilling offert addresses IP and it's not connected in a trusted port,the schema is very simple:1 switch catalyst 2960 PST-S,1 server dhcp and 1 pc client,the PC and the server are in VLAN 10,DHCP SNOOPING is enabled in all ports and no port is trusted,but the client get addresse IP after retyping ipconfig /release and ipconfig /renew in dos commande.the configuration and the version of the switch are in the file attached.I tested the same configuration in a catalyst C3560-24PS and DHCP SNOOPING work normally,i tested in other catalyst 2960-PST-S,but the same probléme:DHCP SNOOPING without effect,the commands typed is:
-ip dhcp snnoping
-ip dhcp snooping vlan 10
View 5 Replies
View Related
Nov 1, 2012
I am having 2960 switch and one port is configured with a VLAN and connected with an unmanageable switch and further one more unmanageable switch was connected to the primary unmanageable switch…
The topology will be 2960 switch -> unmanageable Switch -> unmanageable -> PC connected
The issue I am facing most of the PC are getting IP addresses through DHCP server and very few 5 or 6 PC’s out are not getting the IP from DHCP server.If I switch of the switch and switch on the issue is resolved for those and it will raise for some other PC’s.
View 2 Replies
View Related
Feb 10, 2013
I need to buy a cheap Cisco switch with DHCP server.Can you confirm that 2960-24-S, 2960-24TC-S and 2960-48TC-S be a DHCP server?
View 3 Replies
View Related
Feb 11, 2012
With out using any server, will DHCP be configured in cisco 2950/2960 switch?I man cisco it self should work as a dhcp server also.
View 10 Replies
View Related
Jun 12, 2013
I Have a problem I'm trying to configure automatically my switch over ther DHCP when I start the switch it request an IP from the DHCP from here everythings is fine but it does nothing more,indeed I put on my dhcp the option 66 and 67 which is an adress of my TFTP server and a file to download and the switch seems not to understand theses options , I tried my dhcp with a cisco airport and everythings works fine the File from the TFTP is automatically downloaded into the airport...There is an option to add or am I missing something in order to make it work with my switch ?
My switch : Catalyst 2960IOS VER : 12.2(55)SE5
View 7 Replies
View Related
May 7, 2013
I have a problem with DHCP. I have two 2960 connected with a port channel on ports 47 and 48 as trunk with native vlan 10. I only have this one vlan. In port 1 of sw 1, I have a C800 as DHCP server.
I have an AP autonomous with single ssid on vlan 10. When I connect the AP to sw1, I receive dhcp with no problems.When I connect the AP to sw 2, I’m not getting IP by DHCP.I have DHCP snooping working on vlan 10 on both devices.
The ports where I connect the AP are access ports on vlan 10 config as trusted.The trunk ports are also configured as trusted.The port 1 of ws 1 that goes to the C800 is also configured as trusted.
figure out why I’m not getting IP by DHCP when I connect the AP to the SW 2.The only I notice is that when I connect the AP to sw 2, I get on SW 1 the message of packet drop by option 82, but even after configuring ip dhcp snooping information option allow-untrusted on both switches, the problem persists.
View 5 Replies
View Related
Jun 24, 2012
I need to configure a Cisco 2960 switch as a DHCP server. The current IP address will be on a different seed than the DHCP addresses. i.e.
Switch IP = 10.1.2.3, GW = 10.1.2.1, Subnet = 255.255.255.0
DHCP addresses would be 192.168.1.1 - 200, GW=???? (10.1.2.3?) and subnet would be 255.255.255.0
View 1 Replies
View Related
Jan 28, 2013
I am going to creat VLANs very 1st time therefore for test purpose I have following simple scnerio.I have created 2 VLANs , VLAN2 and VLAN3 on Cisco Catalyst 2960 series switch. Ports 1-12 is assigned to VLAN2 and Ports 13-24 are assiged to VLAN3. Now I have configured DHCP on Microsoft Server 2003 defining 2 scopes with following configurations.
Scope 1 for VLAN 2--- Range is 172.16.0.17 to 172.16.0.30 with subnet mask=255.255.255.240 . Server IP address 172.16.0.17
( Note: Address 172.16.0.17 is excluded from dhcp server Scope 1 and give to the MS server itself)
Scope 2 for VLAN 3----Range is 172.16.0.33 to 172.16.0.46 with subnet mask=255.255.255.240 .
Now in Cisco 2960 series switches, under Vlan 2 and Vlan 3, I have following configurations...
interface Vlan2
ip address 172.16.0.30 255.255.255.240
ip helper-address 172.16.0.17
interface Vlan3
ip address 172.16.0.46 255.255.255.240
ip helper-address 172.16.0.17
Now the problem is when i connect a client computer to any port from 1-12, It gets correct IP address from Scope 1 but when I connect a computer to any port from 13-24, it does not get the ip address.
Further I want to do inter VLAN comunication as well for that purpose i Have an ISR 2900 series router. What further configuration i will have to do on router for inter vlan communication.
View 3 Replies
View Related
Sep 3, 2012
We have a DHCP SERVER implemented in a cisco router 2610.This router is connected to a switch cisco 2960 configured as DHCP SNOOPING. At the switch appear the next log message: [code] The ip address: 10.100.200.1 belongs to DHCP SERVER configured at router cisco 2610. What to do so these log messages does not appear any more? Do I need to do some configuration changes at some switch or router?
View 11 Replies
View Related
Nov 15, 2012
Does the 2960 switches with LAN-Lite support DHCP Server Port-Based Address Allocation?
View 1 Replies
View Related
Nov 13, 2010
I have cisco 800 router, router configure as DHCP server, i want to bind user MAC ID with IP and block only Internet Access.
View 6 Replies
View Related
May 16, 2012
Router 1941 is installed with additional 4 Gig-interfaces card; we have 4 ADSL Router with 4 MB connections. I need to connect all the ADSL connection to the router 4 port and combine them into 16 MB, is there any way to combine 4 Gig interfaces?
View 4 Replies
View Related
Sep 30, 2011
Can the DHCP server on an ASA be configured with static bindings like IOS routers can?
View 2 Replies
View Related
Dec 16, 2010
I am using a 1811W and CCP for configuration. I am trying to assign client names to devices on the LAN so that when a network scanner is used, the client name is displayed. I have attached part of the running config after a binding has been done. My assumption is that the scanner should now show 192.168.1.109 as name <Supermicro>, but the name is blank. Is this configured correctly for what I am trying to acheive?
View 3 Replies
View Related
May 10, 2013
I configured an DHCP server on cisco 3750 switch . Wher in w3750 gets connected to plain l2 switch 2960 on floor and machine gets connected to 2960 port. [code] Below is the description of problem:
-> The Cisco 3750 switch is the DHCP server. VLAN 108 is named as internet vlan.
-> Ports in Cisco 2960 switch has been configured with "switchport access vlan 108".
-> There were no problems at all and everything had been working smoothly.
-> 3 days back, users started complaining that they couldn't access the internet. Up on troubleshooting the issue, I found out that there was an issue with the DHCP server as the computer couldn't get any IP address at all. After setting static IP address, the internet started working again.
If I bind IP to MAc address reservation on core 3750 switch for some time of moment it works but after that machine gets unreachable .I restarted the 3750 switch and also all the 2960 switches over the weekend, however, the issue still hasn't been resolved yet. I did issue the command "clear ip dhcp conflict *", clear ip dhcp binding * but no joy at all.
View 2 Replies
View Related
Sep 23, 2012
I have a customer with a 3750x4 stack. We rebooted the stack over the weekend and the master did not come back up. Upon investigation it was discovered that tghe master was set for Manual Boot. I tried issuing the "no boot manual" command in Global Config mode but it did not change the variable according to a show boot command. According to Cisco documentation, the "no boot manual" command only works on standalone devices. Any way to change the variable while the switch is a member of a stack?
View 1 Replies
View Related
May 8, 2013
Are there issues with the auto upgrade feature for 3750X stacks, either historically or currently?
Some people prefer to upgrade switch stacks manually by disconnectiong the stack cables and uprading code on each switch.
I've done the manual procedure in the past and have not tried the auto upgrade (I have the procedure for the auto upgrade).
View 18 Replies
View Related
Oct 12, 2012
I have a Buffalo WHR-G300N router & I am having probs with assigning a static address to a nas device.I have set up the static ip address i want to use in the nas When I look at the dhcp leases in the router, the device shows up as having an automatic assignment with a different ip address to the one set in the nas.If I manually assign the ip address which I want to use, or, if I edit the automatically assigned entry, the old one stays as an automatic assignment. This means that I then have 2 ip addresses for 1 mac address.When I try to access the nas, with only the automatically assigned address present in the router settings, I can still access it using the ip address I have manually assigned to the nas, even though the manual ip does not show in the router.How can I delete the automatically assigned dhcp lease & just keep my static one??
View 2 Replies
View Related
Feb 7, 2012
I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies
View Related
Feb 11, 2013
I have a 24 port 2960-S that is not communicating with a 2960-LST that it is directly connected to over fiber. The link is up on the LST but will not come up on the -S. What command should I use to bring up this link? I have tried no shut from the (Config-if)# prompt.
View 3 Replies
View Related
Mar 21, 2011
There are list of ips and corresponding mac address in ARP list and Binding setting page of the routers in our company.
I would like to know what it is meant for. This was done by our network admin. I would like to learn about it.
View 2 Replies
View Related
Mar 26, 2013
E4200v2, firmware 2.1.39.145204
Router says "Invalid IP address" when I try to make a manual IP address reservation of the IP address range.
Example: local network 192.168.1.0/24, where .1 is a router, .2 is a reservation, .20-.50 is a range for DHCP.
Before upgrade I didn't have this problem.
View 6 Replies
View Related
Nov 11, 2012
I have some DHCP trouble since I subnetted my network with a 2921. My clinets are in 172.16.2.0/23 and DHCP servers are in 172.16.5.0/24.Sometimes, randomly I guess, I get NACK from my DHCP server, and if I look into DHCP logs I got something like this:
15,11/09/12,09:52:27,NACK,172.16.3.172,switchE51D12.host.com,A0CF5BE51D12,,0,6,,,,,,,,
15,11/09/12,09:52:28,NACK,172.16.3.172,switchE51D12.host.com,A0CF5BE51D12,,0,6,,,,,,,,
15,11/09/12,09:52:29,NACK,172.16.3.172,switchE51D12.host.com,A0CF5BE51D12,,0,6,,,,,,,,
[code]....
View 6 Replies
View Related
Apr 3, 2012
Have a client wanting to hand out public ip addresses to all clients from a PFSense Firewall terminating the internet connection.
How do I allow the Cisco Switches currently in place, configured with private ip addresses in the 10.10.x.x ranges and Vlans, where the main 3550 layer 3 has defined dhcp scopes for each vlan, to relay dhcp requests from all vlans to the PFSense firewall?
I assume I would take off the currently defined dhcp scopes for the vlans and configure each vlan/switch with the ip helper address and specify the PFSense firewall and that Nat would have to be disabled onthe firewall?
View 1 Replies
View Related
Jan 17, 2013
My management has tasked me to give them a high level overview of the different switching we can choose for our new building.
This is what I know so far.4 Closets, each closet has 450 ports,One MDF room that is will contain one UCS Chassis and a Nimble iSCSI SAN.
I am working on the spreadsheet and it looks like this (Not totally filled):
2960s3560x3750x45064510Approx cost (Each, 48PORT, POE+, 10G uplink, Dual PS, IP BASE)
6K7K8K45K75KMax Capacity192432432192384Backplane speed206464520520ProLeast ExpensiveStackable to 9Stackable to 9ProDual PSDual PSDual PSDual PSDual PSProLayer 3 opt
Layer 3 optDual SupsDual SupsConExpensiveExpensiveConNo Dual PSConLayer 2 OnlyCannot stack more than 4
For the MDF I would like to use 2 Nexus 5548's with FEX's, and the layer 3 daughter board. For the IDF's I was thinking of two 4010's.
View 12 Replies
View Related
Nov 21, 2012
I am using a 3750 as a default gateway for multiple Vlans on a few 2960 switches. The trunk lines are configured and working and I have assigned ip addresses to each of the Vlan interfaces on the 3750. My issue is that I can only ping the ip address on the Vlan interface of the 3750 if I have a working computer plugged directly into the Vlan on the 3750. I only have 3 vlans on the 3750 that have hosts directly connected (vlans 2, 10 and 40) the other vlans ( 20 and 70) don't have any clients plugged into them on the 3750 but the hosts reside on 2 different 2960s that connect via trunk ports. How do I keep the vlan interface on the 3750 switch pingable when I don't have hosts directly connected in that vlan on the 3750? (yes, I have enabled ip routing on the 3750)
View 5 Replies
View Related
