Today, my customer have 1 project that have to deploy Cisco 3750 to redirect wccpv2 to Websense Security Gateway.However, i can't excute "ip wccp redirect out" on Cisco Catalyst 3750.
View 5 RepliesI have tried search but found found anything for the 3750 switch about how to redirect HTTP, HTTPS & SMTP traffic to altenative gateway, than our standard gateway on our network, so here goes:
The network that need the HTTP, HTTPS and SMTP traffic redirect is 192.168.5.0/24 and should be redirect to 192.168.5.205 where as all other traffic need to be direct to 192.168.5.199.
Can the 3750 switch do this typo of refirect and if how?? I cannot find anything on the Cisco site stating how or even if it is possible!
I am unable to redirect the HTTPS traffic on my cisco router with WCCP V2
View 2 Replies View RelatedCan i use acl object group with wccp redirect list?My platforms are 6500 and isr 2921
View 1 Replies View RelatedI'm setting up a web cache using the wccp protocol on a Catalyst 3750 stack.
Probably missing something real simple here but when I from the global configuration mode are trying to enter the ip wccp command it just says "invalid input" from wccp. There is no such command.. should be supported on my device from IOS 12.2(37)
I would like to apply a policy-based route on one of our L3 switches (Cisco 3750) to change the next-hop of a couple of servers only. The VLAN where those servers reside got WCCP enabled on it. When I want to apply the route-policy to that VLAN interface it doesn't let me. When I try to apply the same policy to a VLAN interface without WCCP it does work. Is there any Cisco IOS limitations that would prevent me from doing that?
Configuration:
route policy config:
access-list 70 permit ip host x.x.x.x (server IP)
route-map PBR1 permit 10
[Code].....
Amazed I cannot find this in any documentation but I want to know the default aging timer for ICMP redirects on a 3750 switch running at layer 2.
View 10 Replies View RelatedI would like to know if it possible to create a policy map in order to redirect the traffic ( 80 , http, 8080) to a proxy.
My current equipment its a 3750X using a IP Service License ,I was reviewing some options but i want to be sure before implement in production.
We are running in our DC one of the CISCO 2911 terminal server which is connected with HP ARC sight logger.
it is possible to capture user who execute ‘Telnet” or “show line” in the log, I mean all the command entries by user.
How to enable any config on 2911.
i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies View RelatedI have two 3750-X configured to be a stack and I am planning to re-rack these somewhere else. What I would like to know is what are the effects of having the master switch itself lose power? Does it immediately just make the member take over master (there should be no election since there are only 2 switches??) and there would be no loss of connectivity?
View 1 Replies View RelatedI have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
Below is main part of the router config:
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending
[code].....
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net. My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20,I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2),my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to,go out to the internet.
View 3 Replies View RelatedI'm running into what seems a basic ip routing config problem with a Catalyst 3750 (IP Base) switch. I have several VLANS configured on the switch with IP routing enabled, and the switch is connected to the inside interace of a new ASA 5520 as follows:
ASA5520 IP (Default gateway): 192.168.1.1Switchport Gi1/0/1 is configured as a routed port, IP address 192.168.1.3 255.255.255.0Example VLAN is VLAN 100, IP address 192.168.100.1 255.255.252.0 From the switch CLI, I can ping all VLAN addresses, as well as the ASA5520, and the client laptop I'm testing with from VLAN 100.
From the client laptop on VLAN 100, I can ping all switch interface and VLAN addresses (inter-VLAN routing is working), including 192.168.1.3, but I CANNOT ping the default gateway at 192.168.1.1.
Here is the relevant configuration information on the 3750:
!
no aaa new-model
switch 1 provision ws-c3750x-24
system mtu routing 1500
[Code]....
configure qos in Cisco 3750 switch.I have configured below template and applied on the vlan interface.But i am getting the hit on the access list but I am not able to get hit on the class map.
View 2 Replies View RelatedI had a bad expirience with Switch 3750-X. Because of an auditing security processess, my customer ran a software called "Nessus" to do a scanning of vulnerability on the network. When this software is point to switch, the process of the switch will next to 100% and reset. The software only do a listening on the ports to see what ports are opened and the switch should not reset because this. Bellow is the log os switch on the moment of test; we note that the processess 'HTTP' rise moments before the switch reset. I disable the HTTP service on switch but the problem persist. The test was made only one machine connected to switch.
View 4 Replies View RelatedWe have three Cisco 3750 - 48port POE -LAN switches and i am trying to see if there are any issues when we stack POE and Non-POE type of switches.Aslo looking for information on the advanatage and disadvantage the stacking can provide on a Cisco 3750 48port.
View 3 Replies View RelatedThe question is: Will a 3750 switch route Jumbo frame sizes (e.g. 9000 MTU)?
We know that we can change the System MTU to 9000, and someone on a previous thread said that we can change the Routing MTU to 9000 as well, although I couldn't figure out how to do that. However, regardless of how we configure the System MTU and Routing MTU, I don't think we're able to adjust the MTU on L3 VLAN interfaces, so if we want to actually "route" between VLANs on the switch, we're limited to 1500 MTU.
Our situation is that we have a customer connecting to our 3750 switch, and this customer wants to use Jumbo frames. The customer connects to our 3750 switch via their own VLAN, with their own L3 VLAN interface configured on the switch. The customer will point their traffic towards the L3 VLAN interface, then we want to route them onto another VLAN, via a different L3 VLAN interface, before forwarding their traffic. Because of the limitations noted above, specificially regarding the routing between these VLANs via L3 interfaces, I do not think we'll be able to support 9000 MTU frames on this 3750 switch. I think the L3 VLAN interfaces will limit us to 1500 MTU, regardless of what we configured via the global System MTU and Routing MTU settings.
How do you properly remove the QOS queues and configs from the switch.A was using auto qos which created a whole mess of qos configs on my running-config. I did "no mls qos" in conf term but that did not remove the queues.
View 3 Replies View Relatedi want to remove an access layer 3750 48 POE master switch and replace with a new 3750 switch in the stack. i want to copy the same configuration to new switch since the old switch is having POE issue and I got replacement of the malfunctioned switch. we have VTP domain is configured in the network...
View 3 Replies View RelatedCisco 3750, I'm trying to reset the password but cannot communicate with my switch
View 1 Replies View Relatedis it generally possible to connect another switch, such as a 3750 to a port of a fabric extenders (C2232PP-10GE)?
View 1 Replies View RelatedI have Layer_3 " 3750-x " , so I can't do any routing on the switch , so if I need to Upgrade the IOS what is the proffered image that support hte routing , and Is it free or should I pay?
View 7 Replies View RelatedIn Cisco 3750 facing high CPU utilization for specific period. During this period traffic response times across the switch degrades. Steps to identify interface potentially generating traffic. I have attached 'sh proc cpu history' , ' sh ip traffic', 'sh proc cpu sorted' during troubled period .
View 5 Replies View RelatedI have a 2 member 3750-x switch stack that was upgraded to 15.2 today via CNA. All the files were transfered and expanded correctly and it got to the step where the switches needed to be reloaded but on reload they froze.
I connected a console cable and power cycled the stack. I see the flash initialize and then the IOS image start to load. Lots of @ symbols and then nothing. It just sits there. The system light on the switches, while flashing green during the load, is now off. No light at all. But fans are running and the process will repeat itself if power cycled.
i have standalone 3750 switch. RPS light is green and system light is off.
3750TS#sh env all
FAN is OK
TEMPERATURE is OK
[Code].....
i have another switch with same model and ios its RPS light is off and system light is green
We currently have a stack of 5 x 3750 switches and i want to remove switch number 3 (it has the least number of things plugged in). What will happen to switch 4 and 5 will they be renumbered 3 and 4, and will the config automatically update this if it does?
View 2 Replies View RelatedI configured 3750 A switch with vlan 20 and its IP address 192.168.20.41Its default gateway was 192.168.20.3Then i configured 3750 B switch with same default gateway and vlan 20 IP 192.168.20.43My question is now when we stack it becomes single switch and now vlan 20 ip address is 192.168.20.43 thats only IP i can see.So how does stack switch choose vlan 20 IP?Does it choose highest IP address between two switches if they have same vlan 20 as in my case?Also when i go to switch 3750 b by session command and do sh ip route it does not show ip default gateway .Also it shows vlan 20 as admin down .
View 5 Replies View RelatedI have a doubt. In my environment I have two Switch 3750-X in stack.
My question is: How to shutdown remotely only a switch in stack?
I want to configure " Username & Password" on Cisco 3750 switch. I need to configure as "username xxxxxx privilege 15 password 5 xxxxxxx "
Is it possible to create password with level 5 ? I want to know about level 5 "password" & level 7 "password" ?
when i tried I am not able to configure with " password 5"
Our switch is very high cpu in process arp
Am debug ip arp track command the result as below
-- on this switch have interface vlan 201 ip subnet is 10.11.201.1/24
Jun 5 15:30:40.732 GMT+7: IP ARP: rcvd req src 10.11.201.217 0001.6c6b.8ab9, dst 172.27.116.73 Vlan201
Jun 5 15:30:42.150 GMT+7: IP ARP: rcvd rep src 10.11.201.217 0001.6c6b.8ab9, dst 172.27.116.4 Vlan201
Jun 5 15:30:42.150 GMT+7: IPARP_TRACK: ARP tableid(0) 10.11.201.217 Vlan201 mode(1) modified.
Jun 5 15:30:42.150 GMT+7: IP ARP: rcvd req src 10.11.201.217 0001.6c6b.8ab9, dst 172.27.116
and then am try to shutdown vlan database 201 after that the cpu process has to normal state.
How to check the root cacus?
We have two 3750-x stacked switches with IP base license. We need to upgrade them to IP services license. I read some where that it is possible to install IP serivces license to only management switch and no need to purchase/install same license to other switches on the stack. But, I could not find/recall where I read it and as far as I know it was not official cisco documentation.
View 1 Replies View Related