Cisco Switching/Routing :: Nexus 3048 QoS Policing
May 29, 2012Any way of policing traffic on the Nexus 3k platform? I can't find a reference to say policing/shaping is supported.
View 5 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Configuring VPC On The Nexus 3048
May 22, 2013I'm looking for some input on configuring vPC on the Nexus 3048.I know that it's supported to use 1G interfaces for the vPC Peer-Link, but using 2x1G for the Peer-Link would make the Peer-Link a bottle-neck if the 10G ports are used in a vPC. What about using 2x10G ports for the Peer-Link and using the remaining 10G ports in one, or potentially two vPCs. Should that work or is it in any way not recommended? The reason I'm asking is that the 10G ports are called "Uplink" ports in the data sheets for the 3048.
We are planning to connect some servers to the 3048s using vPC with each server connected by 4x1G interface (2x1G for each switch), and then we want to connect a Netapp storage system with two controllers using 2x10G each (the controllers are active/passive, so you can think of it as two separate systems). We would connect controller A with vPC 1x10G to each switch, and controller B in the same way with vPC 1x10G to each switch.
Cisco Switching/Routing :: Nexus 3048 VPC Doesn't Form
Jun 11, 2012I am building up vPC on 2 x Nexus 3048 and found that it did not work properly.The current config as follows,
1. OS: n3000-uk9.5.0.3.U2.2.bin
2. Peer link: 10 x 1G (E1/1 - E1/10) on both devices (I am wondering that 1G interface supports vPC Peer-Link. I heard that upgrading to U3.2 image will work for 1G rather than 10G... )
3. They can ping each other via management IPs
4. Edge switches vPC have not been built yet (I am focusing on Peer-Link and vPC role selection)
[code]....
Cisco Switching/Routing :: Trunking Nexus 3048 With Force10 S4810
Apr 11, 2012I have been assigned the task of trunking VLAN between a Nexus 3048 and a Force10 S4810. This would seem easy enough but I am really having a bear of a time getting it to work. I have devices configured on VLAN 602 on both sides but they just are not talking.
NX0S 3048
interface configuration
----------------------------------
interface Ethernet1/49
switchport mode trunk
[Code].....
Cisco WAN :: Breaking Password On Nexus 3048
Mar 22, 2012I have a brand new Nexus switch that I cannot log into. I do not know the user/pw and think I may have to do a pw reset. Any proc for doing pw recovery on these new devices?
View 1 Replies View RelatedCisco WAN :: Inter Vlan Communication On Nexus 3048
Jan 15, 2013Recently configured one nexus 3048 switch. Create two vlans (Vlan 10 and Vlan 19). Vlan 10 is 10.1.X.X/24 and Vlan 19 is 192.168.X.X/24, connected two pcs one is Vl 10 and second pc 19. But not able to communicate both Vlans.Nexus 3048 are not Support VTP Mode Server, running version 5.0. [code]
View 2 Replies View RelatedCisco Infrastructure :: Nexus 3048 - Compatibility With Ethertype 0x05ff?
Feb 26, 2013How will I know if my catalyst and Nexus switch supports Ethertype 0x05ff. This is for the beacon probes sent out by our ESX Servers.
We will be using Nexus 3048 and we have 3750 catalyst switches as our distro switches.
Cisco Switching/Routing :: 3048 Rack Switch For Data Center
Jan 11, 2012Any recommendations for top of rack switch for within our data centre.Dual power is a requirement, but bandwidth and through put will not be huge as such I have been looking atthe WS-C3560X-48T-L and the Nexus 3048.
View 1 Replies View RelatedCisco Switching/Routing :: Policing Traffic On 4510?
Nov 21, 2012I have two servers on one subnet that each need to replicate to a single server on another subnet. They also need to replicate to each other. This replication is unidirectional so I will refer to the 2 server subnet as the source subnet and the single server subnet as the destination subnet. In order to keep this replication running without killing the MPLS links on either end, we are trying to use a policy-map that limits bandwidth from the source subnet.The Problem:We have created a policy that polices traffic during specific times of day and limits the bandwidth as prescribed, however, bandwidth is also being limited between the 2 servers on the source subnet which is not needed or desired.Class 512K set dscp ef police 1024000 bps 1024000 byte conform-action transmit exceed-action dropClass Map match-any 512K (id 4) Match access-group name DAGExtended IP access list DAG 10 permit ip host 10.20.0.3 host 10.20.0.10 time-range DAG-REP (active) (22793 matches) 20 permit ip host 10.20.0.4 host 10.20.0.10 time-range DAG-REP (active) (14156 matches)The service policy is applied on the input side of the 2 interfaces on which our devices are connected.As you can see, the access list identifies the interesting traffic as traffic from two specific hosts to one specific host. The problem we are having is that bandwidth is also being throttled between the two source hosts even though it is not defined to do so.What can I do to limit traffic from the two source devices to the single destination device without limiting bandwidth between the two source devices?
View 1 Replies View RelatedCisco Switching/Routing :: C3750 - ACL Building For QOS Or Policing
Jun 6, 2012I would like to apply policing on a C3750 interface, for all traffic matching 10.0.0.0 / 8, except for sub net 10.0.0.0 / 24. I plan to apply the following configuration, with an ACL that denies 10.0.0.0 / 24 then accept 10.0.0.0 / 8. I am quite sure of the answer but need a confirmation about the following configuration correct ? (10.0.0.0 / 24 will be not blocked, and no policing will be apply on it?)
ip access-list extended TEST
deny tcp 10.0.0.0 0.0.0.255 any eq 5000
permit tcp any 10.0.0.0 0.255.255.255 any eq 5000
[code]....
Cisco Switching/Routing :: 3560 Egress Policing And Classification
Jan 17, 2012I have a customer who requires to identify and police traffic on egress on a 3560 trunk link. I cannot use ingress classifications because we do not know what route the traffic will take yet. The egress interface connects to multipoint wireless equipment with 4 different bandwidth point to point links. So the ingress traffic may be routed via any one of 4 point to point wireless links connected to the single egress interface. Am I correct in assuming we cannot mark on the egress direction then put the traffic in a SRR shaped egress queue based on the marking ? So we would only have the option to egress queue based on markings applied or trusted on the inbound direction ? I had thought of some kind of policy map/aggregate policer configuration based on the exit VLAN but it seems we can only apply this type of config inbound. From reading the 3560 configuration guides it seems the 3560 cannot deploy the kind of requirements this customer needs. Perhaps they should have deployed some kind of Metro switch ?
View 1 Replies View RelatedCisco Switching/Routing :: 3750x Inbound Port Policing?
Dec 11, 2012dont seem to be able to get policing working inbound on a port 3750X v 15.0(2)
Config is below:
ip access-list extended SMB
permit tcp host 192.168.1.14 host 172.16.1.30
permit tcp host 192.168.1.14 host 172.16.1.31
[Code]....
Cisco Switching/Routing :: IPv6 Filtering / Policing On 2960 Switch?
Jan 3, 2012Trying to control capacity utilization for guest users connecting to a 2960 switch. No problem for IPv4 users, but IPv6 is giving me fits. What I've found out by trial and error so far implies that there is just enough IPv6 smarts in a WS-C2960-24TT-L running c2960-lanbasek9-mz.150-1.SE to make it impossible to control IPv6 traffic. Blocking IPv6 would be sufficient short term, but MAC filtering on type 0x86DD does not appear to work either. Here are the results I've gotten so far:
What "works":
* Protocol ipv6 or an IPv6 ACL in a class map.
* Using a class map referencing ipv6 protocol or an ipv6 ACL in a policy map.
* IPv4 inbound filters and policing.
* Blocking of IPv4 traffic by a MAC ACL blocking type 0x0800 (IPv4) - note that the docs explicitly state that MAC filters do NOT filter IP traffic, except for on this box on this release they do.
What does not work:
* Applying a policy map referencing a class map referencing protocol ipv6 or an IPv6 ACL to an interface. The service policy is accepted by the parser, but is not inserted into the running configuration.
* "class-default" in a policy map only matches IPv4 traffic, not all other traffic.
* Blocking of IPv6 traffic by a MAC ACL blocking type 0X86DD. No problem applying the access-group to the interface, it just doesn't do anything.
I am aware that this box is not supposed to support IPv6 other than for multicast, but as implemented, this is a hole an abuser could drive a MAC truck through.
My questions:
Is this situation unique to this particular 2960 switch or SW release (I also tried 12.2(58)SE2) or does it afflict all 2960's running LANbase?
Assuming the answers to the first two question are negative, what is the minimum requirement to get working IPv6 policing in an edge switch?
Cisco Switching/Routing :: 3560 Rate-limit Vs Policing And Shaping
Nov 27, 2011I am configuring a 3560 to provide internet access for our customers and I need to make sure they don't use more bandwidth than they have contracted for.I see that the 3560 supports the rate-limit command, but was told that I should use traffic shaping and policing along with access lists to manage the bandwidth.Is there a reason that I should avoid using the rate-limit command - it looks much simpler.
View 10 Replies View RelatedCisco Switching/Routing :: Packet Discard On Nexus 5020 Link To Nexus 5K
Feb 23, 2011We are facing issue of continous packet discards On nexus4001L link (int po2) to Nexus5020 switch. Nexus4001L is installed in IBM blade center server and we have FCOE enabled in this setup. [code]
View 2 Replies View RelatedCisco Switching/Routing :: Nexus 7000 With Fabric Extenders Nexus 2000?
Mar 15, 2013I have been tasked to replace the existing Cat 6500 and 3750 switches by Nexus 7000 and Nexus 2000.I was told initially my boss plans to get 2 x Nexus 7000 and then eventually blow up to 4 x Nexus 7000s.For Nexus, is there a list of tasks / points that i need to consider for building the initial design?
Can i just link the Nexus 7000 like the following?
N7k-A ========= N7k-B
| |
lots of N2ks lots of N2ks
Cisco Switching/Routing :: Nexus FEX Transceivers SNMP MIB Nexus 5000
Dec 22, 2011Struggle to find the SNMP MIBS of the Nexus 5000 FEX tranceivers.
View 3 Replies View RelatedCisco Switching/Routing :: Datacenter Design With 2 Nexus 5K And 4 Nexus 2K?
Nov 13, 2012we are planning a Nexus datacenter project with this layout:Our experiences with Nexus switches are not so large until now and the manuals are very extensive.Both N5K´s should be connected directly with all 4 N2K switches. I did not find a layout like this in the manuals. Only a design,where only 2 N2K are connected to one N5K, with this fex config:Now I´m not sure if it is right to make a config like this with the same slots and fex´s or with different slots and fex´s.
View 1 Replies View RelatedCisco Switching/Routing :: Nexus 7010 / VSS - Does It Support Virtual Switching?
Apr 9, 2010Does the nexus 7010 support virtual switching yet? All of the posts I have found from about a year ago say that it is going to be supported, but there were no dates listed. I heard the same thing from Cisco a while back, but haven't followed up with it.If it is supported finally are there any configuration guides available for it?
View 7 Replies View RelatedCisco Switching/Routing :: Facebook Forum Data Center Switching With Nexus 5000
Oct 8, 2012Lucien is a customer support engineer at the Cisco Technical Assistance Center. He currently works in the data center switching team supporting customers on the Cisco Nexus 5000 and 2000. He was previously a technical leader within the network management team. Lucien holds a bachelor's degree in general engineering and a master's degree in computer science from Ecole des Mines d'Ales. He also holds the following certifications: CCIE #19945 in Routing and Switching, CCDP, DCNIS, and VCP #66183
View 1 Replies View RelatedCisco Switching/Routing :: Nexus 5010 Support For Inter VLan Routing
Jan 10, 2012Can nexus 5010 supports inter v lan routing , as there is no core switch and router available in current network.
View 2 Replies View RelatedCisco Switching/Routing :: Nexus 5000 LAN Routing Connection Deployment
May 16, 2013We have our Nexus as our default gateway (101.1) and the default VLAN1 is setup with two subnets 101.X and 102.X. The DHCP server is using a superscope setup to accomodate the overflow of devices requesting IPs on 101, so when 101 is consumed persons are able to obtain a 102.X IP address. The setup is basic on superscope. The issue is some times the routing to the firewall with a 102.X is not always 100%. Somedays all goes well and the 102 subnet is routed out to the firewall and its a good day. However, such as today a 102.X address is not routing as it did 24 hours ago. I am perplexed as to why this is behaving unpredicatable. Here is running-config for VLAN1 to show the 102 as secondary address to VLAN1.
View 2 Replies View RelatedCisco Switching/Routing :: Nexus 7010 - Inter-VLAN Routing On Multilayer VPC Environment
Feb 16, 2011you find attached my network architecture with 2 Nexus 7010 on core layer and 2 Nexus 5020 on distribution layer, each one with 1 N2148T fabric extender switch. PC-A1 and PC-A2 are connected to one N2148T, PC-B1 is connected to the other N2148T. Nexus-7000-1 is HSRP Active for all VLANs, Nexus-7000-2 is HSRP standby. PC-A1 and PC-A2 are connected to VLAN A, PC-B1 is connected to VLAN B. PC-A1 and PC-A2 have the same default gateway correspondent to IP HSRP on VLAN A. It happens that PC-A1 is able to ping PC-B1 while PC-A2 is unable to ping PC-B1. If I issue a traceroute from PC-A2 I see Nexus-7000-2’s physical IP address as the first hop even if Nexus-7000-2 is HSRP standby. After the first hop the traceroute is lost. If I shutdown Port-channel 20 on Nexus-5000-2, PC-A2 starts to ping PC-B1.I can’t understand what’s wrong in this architecture.
View 6 Replies View RelatedCisco Switching/Routing :: Nexus 7010 / 5510 - Run OSPF As Layer 3 Routing Protocol Between VPC Peer Links
Mar 25, 2012I have an environment where i have two nexus 7010 switches, along with 2 nexus 5510's. I need to run OSPF as a layer 3 routing protocol between the vpc peer links. I have 1 link being used as a keep alive link, and 3 other links being used as a VpC link.
1) Is it best to configure a separate Vpc VLAN i.e 1010
2) Is it best to configure a vrf context keep-alive
3) just have the management address as the peer ip's.
Cisco Switching/Routing :: Nexus 5548P Routing
Feb 6, 2012I have a pair of 5548P switches with the L3 daughter cards installed. Using the base license as I just need RIP routing. I have the two switches setup and have the RIP routing feature enabled. When I "turn on" routing using RIP I do not get any routes from my existing L3 switch (3750). I probably don't have routing setup correctly. With the 3750 IOS, I just turned on RIP with the router rip command and added a couple of network statements. On the nexus I have run router rip {instance} and left it at that. I am not getting any routes from my 3750. The 5548s are using the management ports and are connected to my existing network with L2 trunks. Does any know of a setup guide for RIP? I have used the Nexus 7000 RIP guide but still can't get it to work.
View 2 Replies View RelatedCisco Switching/Routing :: 10G Ports On Nexus 7K?
Jul 2, 2012I''ve trying to bring up ports on a N7K-M108X2-12L card using X2-10GB-SR modules.
All ports are in a VDC and configured to accept the M1 card:
vdc_id vdc_name state mac type lc
------ -------- ----- ---------- --------- ------
2 cam-cor-csw-sfy-01 active 64:a0:e7:43:f0:c2 Ethernet m1 f1 m1xl
[Code]....
Cisco Switching/Routing :: 7010 - How To Add Two Nexus 5K In DC
Feb 18, 2013This is regarding Nexus core switch 7010. We are already running two nexus 7K with ten Nexus 5k. Currently we are going to add two new Nexus 5k in our DC. In the 7K we already running two VDC's.
View 8 Replies View RelatedCisco Switching/Routing :: Nexus 5k High Fan RPM
Jun 8, 2013The fans 1 & 2 in Module 1 on the Nexus5K are still experiencing the very high RPM and speed issue.
I have replaced the fan from another operational Nexus5K, and the fans are fine in the other Nexus. The replacement fans also have the same issues, so it is not a fan hardware issue.
There are no threshold alarms. the only log entry that is related to this is as follows:
%NOHMS-2-NOHMS_ENV_ERR_FAN_SPEED: System minor alarm in fan tray 1: fan speed is out of range on fan 1. 7950 to 12500 rpm expected. I have provided the output for both the fan detail and the temperature.
N5K-01# sh environment fan detail
Fan: --------------------------------------------------- Module Fan Airflow Speed(%) Speed(RPM) Direction --------------------------------------------------- 1 1
[Code].....
Cisco Switching/Routing :: Per-VLAN QoS On Nexus 5K?
Feb 22, 2012I was reading a QoS walkthrough earlier to try to solve my problem and I noticed that in IOS, you can specify "match vlan" in a class map. This is not available in NX-OS. I'm not doing any routing on the 5K so I cannot match on ACL, and port where traffic is received is a trunk sharing other types of traffic I'd like to classify elsewise.
How can I match traffic on a per-VLAN basis?
Cisco Switching/Routing :: How To Configure Nexus 5K
Oct 26, 2011How to configure a nexus 5K?
View 3 Replies View RelatedCisco Switching/Routing :: Nexus 7k - Fex Not Loading
Mar 14, 2013Just upgraded Nexus 7k from 5.2.1 to 5.2.7 (just system and kickstart image and NOT epld image). but after upgrading the one of the fex(n2k) dont seem to come online (this nexus 7k has two n2k and one of them came online and working fine)
[code]....
Cisco Switching/Routing :: QOS By VLAN On Nexus 5k?
Aug 14, 2012I have a couple of Nexus 5ks that I want to put QOS on for the servers running behind it but also have voice running across it. Voice doesn't play well with jumbo frames so I'd like to put QOS only on the voice vlan.
View 1 Replies View RelatedCisco Switching/Routing :: Vlan On Nexus 7K Is Down
Apr 17, 2013I am working in my lab and I was adding a new L2/3 vlan
vlan 555
name test
int vlan 555
ip address 1.1.1.1/24
no shut
I have also ensured that this vlan is added to the port channel going to my Nexus5K's. I added the vlan to the 5K's and also ensured that vlan 555 is traversing the peer link. all is good there. I have also placed a device on a interface on the 2k as a access switchport on vlan 555
Here is my problem, the L3 interface will NOT come up on the 7K
LAB-DSW01# sh ip int brie
IP Interface Status for VRF "default"(1)
Interface IP Address Interface Status
Vlan555 1.1.1.1 protocol-down/link-down/admin-up
I have gone throug just about everything I can think of and I am still unable to get this L3 interface to come up. I have other L3 interfaces on this device that are configured exactly the sameway without any issue at all. All the existing interfaces are working properly, it's jut this new interface that I am trying to add.
I am running version 6.0.1 on the 7K and 5.2.1.N1.4 on the 5K.
