Cisco WAN :: Breaking Password On Nexus 3048
Mar 22, 2012I have a brand new Nexus switch that I cannot log into. I do not know the user/pw and think I may have to do a pw reset. Any proc for doing pw recovery on these new devices?
View 1 Replies
ADVERTISEMENT
Cisco WAN :: Inter Vlan Communication On Nexus 3048
Jan 15, 2013Recently configured one nexus 3048 switch. Create two vlans (Vlan 10 and Vlan 19). Vlan 10 is 10.1.X.X/24 and Vlan 19 is 192.168.X.X/24, connected two pcs one is Vl 10 and second pc 19. But not able to communicate both Vlans.Nexus 3048 are not Support VTP Mode Server, running version 5.0. [code]
View 2 Replies View RelatedCisco Switching/Routing :: Configuring VPC On The Nexus 3048
May 22, 2013I'm looking for some input on configuring vPC on the Nexus 3048.I know that it's supported to use 1G interfaces for the vPC Peer-Link, but using 2x1G for the Peer-Link would make the Peer-Link a bottle-neck if the 10G ports are used in a vPC. What about using 2x10G ports for the Peer-Link and using the remaining 10G ports in one, or potentially two vPCs. Should that work or is it in any way not recommended? The reason I'm asking is that the 10G ports are called "Uplink" ports in the data sheets for the 3048.
We are planning to connect some servers to the 3048s using vPC with each server connected by 4x1G interface (2x1G for each switch), and then we want to connect a Netapp storage system with two controllers using 2x10G each (the controllers are active/passive, so you can think of it as two separate systems). We would connect controller A with vPC 1x10G to each switch, and controller B in the same way with vPC 1x10G to each switch.
Cisco Switching/Routing :: Nexus 3048 QoS Policing
May 29, 2012Any way of policing traffic on the Nexus 3k platform? I can't find a reference to say policing/shaping is supported.
View 5 Replies View RelatedCisco Switching/Routing :: Nexus 3048 VPC Doesn't Form
Jun 11, 2012I am building up vPC on 2 x Nexus 3048 and found that it did not work properly.The current config as follows,
1. OS: n3000-uk9.5.0.3.U2.2.bin
2. Peer link: 10 x 1G (E1/1 - E1/10) on both devices (I am wondering that 1G interface supports vPC Peer-Link. I heard that upgrading to U3.2 image will work for 1G rather than 10G... )
3. They can ping each other via management IPs
4. Edge switches vPC have not been built yet (I am focusing on Peer-Link and vPC role selection)
[code]....
Cisco Infrastructure :: Nexus 3048 - Compatibility With Ethertype 0x05ff?
Feb 26, 2013How will I know if my catalyst and Nexus switch supports Ethertype 0x05ff. This is for the beacon probes sent out by our ESX Servers.
We will be using Nexus 3048 and we have 3750 catalyst switches as our distro switches.
Cisco Switching/Routing :: Trunking Nexus 3048 With Force10 S4810
Apr 11, 2012I have been assigned the task of trunking VLAN between a Nexus 3048 and a Force10 S4810. This would seem easy enough but I am really having a bear of a time getting it to work. I have devices configured on VLAN 602 on both sides but they just are not talking.
NX0S 3048
interface configuration
----------------------------------
interface Ethernet1/49
switchport mode trunk
[Code].....
How To Set Up A LAN Without Breaking Home Networks
Oct 6, 2011I'm going to a LAN party with some friends soon. We've tried to have one many times before but it always fails because we cannot get the computers to link up. The reason for that, I think, is because the host (of the party) has his computer on a home network. I need to know how to get all of our computers talking to each other without making it hard for him to get back on his home network.I have a Linksys WRT54g broadband router that I used to use for internet and LAN on my home network. I currently use a Linksys WRT160N V3, but I was hoping to not have to remove that one... 4 computers at the party will be using Win 7 and the 5th is running XP
View 1 Replies View RelatedTP-Link 300Mbps Wireless :: TL-WR941ND Breaking Internet Connection
Feb 9, 2013Region : Poland
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel. 54965n
ISP : Toya Lodz
This is already my second model of the router, which got under warranty. The first model had a problem because it brokes off Internet connections. This second model also breaks the connection. I'm going to give it to complain. Before I do it I would like to ask if there are any ways to improve the router without the need to dispose of the device.
D-Link DIR-601 :: Firmware Up Gradation Result In Breaking Of VoIP Service
May 8, 2011Last week I upgraded the firmware in my D LINK DIR-601 from 1.01NA to 1.02NA. This resulted in breaking my VoIP service (causing one-way audio on incoming calls - callers could hear me but I could not hear them). I am using a SIP-based service from Speakeasy (Broad soft) with a Cisco 504G phone. Once I downgraded the router back to 1.01NA, the service started working again.
I don't know if anybody else has reported an SIP-related issues with this firmware.
Cisco Switching/Routing :: 3048 Rack Switch For Data Center
Jan 11, 2012Any recommendations for top of rack switch for within our data centre.Dual power is a requirement, but bandwidth and through put will not be huge as such I have been looking atthe WS-C3560X-48T-L and the Nexus 3048.
View 1 Replies View RelatedCisco Switching/Routing :: Packet Discard On Nexus 5020 Link To Nexus 5K
Feb 23, 2011We are facing issue of continous packet discards On nexus4001L link (int po2) to Nexus5020 switch. Nexus4001L is installed in IBM blade center server and we have FCOE enabled in this setup. [code]
View 2 Replies View RelatedCisco Switching/Routing :: Nexus 7000 With Fabric Extenders Nexus 2000?
Mar 15, 2013I have been tasked to replace the existing Cat 6500 and 3750 switches by Nexus 7000 and Nexus 2000.I was told initially my boss plans to get 2 x Nexus 7000 and then eventually blow up to 4 x Nexus 7000s.For Nexus, is there a list of tasks / points that i need to consider for building the initial design?
Can i just link the Nexus 7000 like the following?
N7k-A ========= N7k-B
| |
lots of N2ks lots of N2ks
Cisco Switching/Routing :: Nexus FEX Transceivers SNMP MIB Nexus 5000
Dec 22, 2011Struggle to find the SNMP MIBS of the Nexus 5000 FEX tranceivers.
View 3 Replies View RelatedCisco Switching/Routing :: Datacenter Design With 2 Nexus 5K And 4 Nexus 2K?
Nov 13, 2012we are planning a Nexus datacenter project with this layout:Our experiences with Nexus switches are not so large until now and the manuals are very extensive.Both N5K´s should be connected directly with all 4 N2K switches. I did not find a layout like this in the manuals. Only a design,where only 2 N2K are connected to one N5K, with this fex config:Now I´m not sure if it is right to make a config like this with the same slots and fex´s or with different slots and fex´s.
View 1 Replies View RelatedCisco Switching/Routing :: Catalyst 3750X Is Caching Tacacs Password Or Not Asking For Password
Aug 8, 2012the following information before:
Switch: WS-C3750X-48P (Stack with 2 Members)
IOS: 12.2(58)SE2
Lic: IPBASEK9
[Code]....
Since i added another Member to the Stack, i'm facing the following problem: When i login with my tacacs user account, i will not be asked for the password. The same thing is for the tacacs account of my colleague, after entering the username he is logged in. It seems for me, that the passwords are cached only for this Switch.
Cisco WAN :: VPC Between UCS C210M2 And Nexus 7K
Oct 8, 2011I have One UCS 210M2 server and two Nexus 7K.We want to configure portchannel(etherchannel) UCS two NIC card and connect to each nexus 7K.Is this design supported, connecting UCS port-channel on two nexus 7K? we dont have 5K or 2K switches.What configuration required from Nexus 7K to achieve this vPC directly with UCS 210M2 servers?
View 6 Replies View RelatedCisco :: Nexus 5K Mac Address-table?
Aug 20, 2012Can someone throw me a bone on what might be occurring here?
View 7 Replies View RelatedCisco WAN :: Nexus 7010 PBR Without Track
Sep 15, 2011Trying to implement PBR in N7K? I found that there is not track mechanism can use in "set next-hop ip", so if the next-hop is unreachable that the route might be died.
View 0 Replies View RelatedCisco WAN :: Radius Configuration On Nexus 7k
Jun 5, 2012Configuring radius authentication on Nexus 7k?I have heard once you have configured the radius you are only able to run show commands on it.
View 1 Replies View RelatedCisco WAN :: How To Setup Nexus 5548
May 5, 2013I have a cisco box Nexus 5548 box i need to setup.
what is the basic configuration i need to do so as to setup the following:
1. Management interface
2.Reduce the switch priority to join other switches in the network
3.setup etherchannel etc
Cisco WAN :: Multicast Routing Between Two Nexus 7Ks?
Dec 9, 2012I have multicast routing setup between two Nexus 7K's.These Nexus 7K's act as the distribution layer and they connect to 48 different 4507 access layer switches (VPC) and 3 6509 core layer switches.The 4507 swiches have two supervisor modules. One acting as active and the other as hot standby. Let's assume that multicast is working on the active module. If I pull out the active module the hot standby takes it's place. This is where multicast stops working on the switch.How can I get both Nexus 7K's to work with multicast at the same time. Here is an example of show ip mroute from both Nexus 7K's:note that DR02 has a lot more entries in the routing table. Is this working as designed?
DR01-C7018# sh ip mroute
IP Multicast Routing Table for VRF "default"
(*, 224.0.0.0/4), bidir, uptime: 1y11w, pim ip
Incoming interface: Ethernet3/1, RPF nbr: 172.18.254.109
Outgoing interface list: (count: 1)
Ethernet3/1, uptime: 29w3d, pim, (RPF)
[code].....
Cisco :: LMS 4.1 And Nexus 7k User Tracking?
Sep 1, 2011I am trying to determine why hosts off our Nexus 7010s are being picked up in UT. Since LMS 4.0.1, UT should be supported on these devices.When adding the Nexus devices to DCR, provide the netadmin SNMP RO credential.When other SNMP RO credential is provided, user tracking will not collect end host data.I think I have this setup correctly as the device center test passes when cehcking snmp ro credentials.Our 7010s are running NX-OS 5.0(3) - earlier than the recommended version - might that cause issues? We are not using VRFs other than the default and management.
Here is my snmp section:
sh run | sec snmp
ip access-list copp-system-acl-snmp
10 permit udp any any eq snmp
10 permit udp any any eq snmp
20 permit udp any any eq snmptrap
[code]....
Cisco :: Setting Up Netflow On Nexus 7K
May 22, 2013I was trying to get Netflow setup on one of my 7K VDCs and ran into a problem. While netflow data was reaching the collector, IP src/dst information was not appearing in the analyzer tool. I could not see any information about conversations. So I contacted the company that makes the collector/analyzer and the directed me to a blog on their site and told me to setup the 7K exactly as it is described in the blog post. I did and a bit later the ip src/dst address information appeared. So the only difference between the two configurations was that in the first case I tried to define a record and in the second case, no record was defined and instead the orginial-netflow parameter was used in the "flow monitor" section. [code]
I referenced the document "Cisco Nexus 7000 Series NX-OS System Management Configuration Guide,Release 6.x", Chapter 19 - Configuring NetFlow.It's clear to me that I didn't do something right in defining my own record since that's really the only difference between the config that worked vs the config that didn't. However, the documentation I referenced doesn't really provide useful information about how to create a record (above and beyond what I can already see by typing '?' at the CLI).
For example, the "match" command makes no sense to me. Usually when you have a match command it is accompanied by some sort of ACL. In the "flow record" section a match command would be something like "match ipv4 source address" but that's it. What does that mean? Match anything that has a IPv4 source address?? That doesn't make much sense. The collect commands are equally as bewildering. If I want to define my own record (and not use the original-netflow parameter) what do I need to do in the "flow record" sub-configuration to get Nexus to send ip src/dst information to the collector (which, I would think, is basic information to send - what good is netflow data without it)?
Cisco WAN :: IOS Upgrade On Nexus 7018?
May 5, 2011I am trying to upgrade IOS on my Nexus7018 from version 5.12 to 5.13. I have managed on all my three out of four Nexus succesfully but one of them is keep coming with this error,
""""N1K-7018-1# install all kickstart bootflash:n7000-s1-kickstart.5.1.3.bin system bootflash:n7000-s1-kickstart.5.1.3.bin
Another install procedure may be in progress. Please try later.
how to find out which other install is running or stop any install procedure.?
Cisco WAN :: Multicast Mac On Nexus 7010
May 18, 2012i have a couple of nexus 7010 (5(2)3a) connected to a checkpoint in HA(active/active)I have now to configure multicast mac..i found this commmand: [code]
View 1 Replies View RelatedCisco Switches :: Nexus 5K Multicasting
Mar 24, 2013We have configured multicasting for our Nexus 5K switches. and for the most part everything seems to be working until recently.
Setup is we have 2 Nexus 5k switches connected via Dark FIber from Site A to Site B. Site A is sending the multicast traffc and Site B is receiving it.
Cisco WAN :: Nexus 7k Configuration Commands For PBR?
Sep 25, 2012I am looking to configure PBR in Nexus. The current setup in IOS is :
interface Vlan10
ip address 172.27.206.1 255.255.255.0
ip address 172.27.208.1 255.255.254.0 secondary
ip policy route-map Vlan_10_to_Corp
route-map Vlan_10_to_Corp permit 10match ip address Vlan_10_to_Corp
set ip next-hop 172.27.209.250!route-map Vlan_305_to_EFH permit 30
[code]....
But, Nexus PBR will not work with deny statements init. Now, what options do I have ?
Cisco WAN :: Routing Between VRFs On Nexus 7k?
Nov 21, 2012I want to create following setup, wanted to know that how is this achievable
3 VRF on nexus 7k and all VRFs connected to each other in following manner through virtual firewall contexts
N7K-VRF1----FW-CONTEXT1----N7K-VRF2---FW-CONTEXT2-----N7KVRF3
| | |
SERVER1 SERVER2 SERVER3
Now i want that SERVER1 should be able to speak to SERVER2 and SERVER3 and i want to exchange routes betwene VRFs through OSPF.
Cisco WAN :: EtherChannel On Nexus 2000
Apr 5, 2011I am trying to connect my sever with daual homed to two Nexus 2232 fex which are part of two Nexus 5548 vPC pair( topologyu attached) but getting error on Nexus 5548 as below,
Not sure its allowed under Nexus 2000.
""Port-channel members across FEXes is not allowed, new member Ethernet101/1/12(0x1f6402c0) existing membe: : Ethernet100/1/12 command failed: port not compatible [All HIF member ports not in same pinning group]"""
Cisco WAN :: Upgrade Path For Nexus 7K From 5.0(2a) To 5.2x?
Feb 4, 2013Any good link that explains the NX-OS upgrade path? I am trying to go from 5.0(2a) to 5.2x.
View 1 Replies View RelatedCisco WAN :: Do Nexus 7k Support VPLS
Mar 11, 2012I can't find any configuration info for any MPLS layer 2 extension features for the Nexus 7k devices, is this a strategic decision by Cisco to promote OTV?
View 3 Replies View RelatedCisco :: Nexus 1000v QoS Based On IP ACL?
Mar 28, 2012I want to apply QoS policy on a particular VM for specified port range only. I have created following script file but that doesnt work. I mean it doesnt apply any policy on vm residing on Veth1.
config t
ip access-list acl_in
101 deny tcp any any eq 443
exit
[Code].....