Cisco Switching/Routing :: Change Airflow Of The Nexus 5548UP?

Aug 6, 2012

is it possible to change the airflow of the Nexus 5548UP in the field by replacing fan and power supply or must the correct airflow been ordered.

View 9 Replies


ADVERTISEMENT

Cisco Switching/Routing :: Nexus 5548UP Change Peer Keep Alive Link

Apr 19, 2013

I have a pair of Nexus 5548UPs that have some high priority servers running on them.  Servers are ESX hosts running Nexus 1000v's.  Each host has multple connections in a VPC to both 5548s.  We have been having intermittant ping loss and slowness of traffic to the VM's on these hosts.  I was poking around trying to figure out what the issue could be and found that the peer-keepalive command was not set to send the heart beat across the mgmt0 interface.  I would like to change this to point it accross the mgmt0 interface. Any tips or advice for me on making this change with production servers running on the switches?  I do not want to cause any loss to any systems when I make this change. [Code] ..........

View 3 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP VPC Configuration

Jan 26, 2012

I have followed every piece of cisco documentation I could find on this and I still can't get vPC configured to actually work.  The VLANs stay in a suspended state so no traffic flows across.  Below is my configuration:vrf context management  ip route 0.0.0.0/0 10.86.0.1vlan 1,vlan 86  name I.S_Infrastructure,vpc domain 1  role priority 1000  peer-keepalive destination 10.86.0.4,interface Vlan1,interface Vlan86  no shutdown  description I.S._Infrastructure  ip address 10.86.0.1/24,interface port-channel1  switchport mode trunk  vpc peer-link  spanning-tree port type normal,interface Ethernet1/1  switchport mode trunk  channel-group 1 mode active,interface Ethernet1/2  switchport mode trunk  channel-group 1 mode active ,interface Ethernet1/3,escription Connection to Mgmt0  switchport access vlan 86  speed 1000.

View 8 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP / Two Management Interfaces For N5k

Jan 10, 2013

I have a Nexus 5548UP that would be managed by two organizations. Is it possible to set IP addresses for mgmt0 and an SVI (or an L3 interface) without using the L3 daughter card? I don't want to route between VLANs, just to separate management traffic.

View 4 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP / L3 Cannot Do Inter-VRF Communications?

Aug 28, 2012

I'm trying to get a node in SVI1 on VRF1 to speak to another node in SVI2 on VRF2 to reach each other.  After hours of failure, I went to outside resources.  Everything I read on the internet says it's not possible on this platform and at least one TAC engineer seems to agree.
 
I just can't believe such a high-end data center switch is not capable of handling such a basic feature.

View 1 Replies View Related

Cisco Switching/Routing :: Replacing C4507R-E With Nexus 5548UP?

Jul 25, 2012

We currently have an environment with a 4507 as the core switch connected to four stacks of 3750e's in the wiring closets. A pair of Nexus 5548UP's also hangs off the 4507, but at the moment more or less dedicated to a certain purpose..The 5548UP's have the L3 daughter card installed.
 
My question is: Can a pair of Nexus 5548UP's do a C4507's job? Would we be able to decomission the 4507 and replace with the existing 5548UP's + FEXes?

View 1 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP VPC Domain With 1x L3 Card

Apr 9, 2013

I can't find anywhere whether it is possible to create a vPC domain with 2 Nexus 5548UP switches, where only 1 Nexus 5548UP has a L3 daughter card.

View 3 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP To 2248 Design

Aug 10, 2012

This past networkers I was at the Cisco booth discussing how the 2248 can connect to the 5548 and have server connectivity.  It was told to me that now, as of a fairly recent NX-OS release, you can have the 2248 going dual-homed to both 5548 via VPC and then have a server connected to both 2248 and be in active-active mode.  Is this correct?
 
When we first deployed our 5548 and 2248 we had to put the 2248 in a straight pin mode, where it only had connections to one 5548 and then the server would dual connect to the 2248's and be in active-active mode.  I was told that this changed with an NX-OS release however documentation still seems to be fragmented on what exactly is the case. 

View 3 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP - Management Interface

Apr 21, 2013

How separate is the management interface on a Nexus 5548?
 
In context - what's the risk of having a layer 2 only Nx5K in a DMZ and running the managment ports down into an internal managment VLAN, to form peer-keepalive links and software upgrades.

View 4 Replies View Related

Cisco Switching/Routing :: How To Let Nexus 5548UP Act As DHCP Server

Nov 14, 2011

it's possible to let the Nexus 5548UP act as a DHCP server? (or if it will be possible in future releases)

View 3 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP - FCoE QoS Configuration

Dec 6, 2012

I am looking to implement a QoS policy on a pair of Nexus 5548 UPs. FCoE is a factor here. I have created the following configuration and would like to get a few pairs of eyes to take a look at this for a quick sanity check.
 
How to make sure this config is valid. Also, I realize I'm applying an MTU of 9216 to all classes right now, this will be phased out incrementally.
 
class-map type qos match-all class-platinum
  match cos 5
class-map type qos match-all class-gold
  match cos 4
class-map type qos class-fcoe
  match cos 3
[code]....

View 1 Replies View Related

Cisco Switching/Routing :: Add 2 X Nexus 5548UP Switches At Site 1

Mar 5, 2013

I have 2 sites located approximately 30 kilometers apart.  I will call them site 1 and site 2.The sites are connected by a Layer 2 1GB fibre connection.I would like to add 2 X Cisco nexus 5548UP switches at site 1 and connect these 2 X Cisco nexus 5548UP switches via GLBP
 
I would then like to add 2 X Cisco nexus 5548UP switches at site 2 and connect these 2 X Cisco nexus 5548UP switches via GLBP.I would then like to connect the 2 X Cisco nexus 5548UP switches at site 1 and the 2 X Cisco nexus 5548UP switches at site 2 via GLBP.

View 3 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP With L3 Card / Inter-VRF Not Possible?

Aug 28, 2012

I just received a Nexus 5548 to configure as the core of the Datacenter LAN.  Is it true that the VRFs created cannot talk to each other???  I can't seem to find any documentation on how to do this and at least one TAC engineer half-heartedly believes it's not possible, either.
 
Basically, I'm trying to get an SVI in VRF1 to be able to talk to an device on another SVI in VRF2.
 
I can't believe this high-end switch, that is so capable in every regard, cannot handle this feature.

View 1 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP Switches - Load Balancing?

Mar 10, 2013

The best option for load balancing between 2 X Cisco nexus 5548UP switches located at one site and connecting to 2 X Cisco nexus 5548UP switches located at another site.
 
The sites are connected via a 1GB fibre connection. I am unable to use GLBP until GLBP is supported in further software releases.

View 1 Replies View Related

Cisco Switching/Routing :: LLDP Chassis Discovery On Nexus 5548UP?

May 1, 2012

I'm seeing several error messages like these in the logs of my Nexus 5548UP switches.

2012 Apr 24 16:39:41.470 SSV_5K_SW2 %LLDP-5-SERVER_ADDED: Server with Chassis ID aaaa.bbbb.cccc Port ID mgmt0 management address X.X.X.X discovered on local port mgmt0 in vlan 0 with enabled capability Bridge
 
2012 May  2 05:05:00.627 COR_CCO-NX-5548-UP_01 %LLDP-5-SERVER_REMOVED: Server with Chassis ID aaaa.bbbb.cccd Port ID aaaa.bbbb.cccc on local port Eth1/1 has been removed
 
2012 May  2 05:06:40.328 COR_CCO-NX-5548-UP_01 %LLDP-5-SERVER_ADDED: Server with Chassis ID aaaa.bbbb.cccd Port ID aaaa/bbbb.cccc management address NIL discovered on local port Eth1/1 in vlan 0 with enabled capability None
 
I will say that these 5548s are serving as the distribution layer for a UCS chassis (2x 6120 FIs) but didn't know what kind of visibility the Nexus would have into that - the chassis keyword is what's alluding to this in my mind, and I'm seeing these messages whenever interfaces that connect downstream to the fabric interconnects are brought up or down.

View 2 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP Connectivity With Router 2811

Aug 15, 2012

In the existing network we have Cisco 2811 router connected to Corporate MPLS cloud. Cisco 2811 is connected to Catalyst 6509 switch(set based IOS with MSFC card). Along with that we have two Catalyst 5509. We are upgrading the access layer by replacing catalyst switches with Nexus 5548 & 2248.
 
For a purpose of testing I have connected 5548 & 2248. Created cPC and ether channels between two. SVI and HSRP configuredon 5548. I am terminating 2651 (test router) on 2248 port 101/1/1. On 5548 I have enabled EIGRP on vlans. I am unable to ping to 2651 from nexus switch 5548 and vice-versa. I can see both devices on CDP but I do not see eigrp neighborship formed.
 
What configuration should go in 2248 and 2651 in order to establish a connection between two? If test is successful then I will connect 2811 to 2248 during actual migration. I assume that in testing if it works for 2651 then it must work on 2811 router.

View 67 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP - (Physical Address Changes) Messages In SolarWinds

Dec 9, 2012

We have recently upgraded oor LAN and we are using couple of Nexus5548UP switches in the core with 2960 stacks as access switches. Each access switches stack is connnected to both core switches with link being port-chanels and VPCs. All is working fine, but our SolarWinds management platform (NPM) is being flooded with "Physical Address changed" events. Here is an example of messages:
 
NSW_Core_2 - Ethernet1/7 Physical Address changed from 000000003811 to 73616D653811
NSW_Core_2 - Ethernet1/7 Physical Address changed from 200B82B43811 to 000000003811
 
For each interface I have messages like these repeating.I am not sure what those messages means or if there is actually anything wrong. Performance of the network is good, there are no errors on any interfaces and I do not see anything related in the switch loggs.

View 4 Replies View Related

Cisco Switching/Routing :: Nexus 5548UP With 2232TM Fabric Extender And Server Teaming

Oct 11, 2012

Need clarification on the VPC with 5k and 2248 Fabric Extenders. My question  is can each fabric extender uplink to two different 5ks, and  at the same time, have servers connected to two both fabric extenders with a VPC.So basically, the server NIC will team with two different fabric extenders, and each fabric extender will connect to two different 5k's.

View 3 Replies View Related

Cisco Switching/Routing :: Enable Jumbo Frames On Single VLAN (Nexus 5548UP)

Sep 17, 2012

We are currently using two Nexus 5548UP's as our Datacenter Network Core.  I have a pretty simple objective:  I would like to enable Jumbo Frames on a single VLAN only(VLAN 65).  This VLAN is used strictly for backups.  I do not want to enable Jumbo Frames on the other VLANs(VLANs 1-10).  Im not sure what the best way to do this is.....or if it is even possible but I am hoping to get some configuration examples.

View 7 Replies View Related

Cisco Switching/Routing :: Nexus 7000 STP Topology Change In All Connected Vlans

Jun 2, 2013

our pair of Nexus 7000 are configured with RSTP.On the Edge-Switches we have seen an STP topology change in all connected vlans.On N7k the topology has also changed what we`ve only seen in the output of the stp details [code]

I like to configure a logging for topology changes, but i havn't found a command.
 
Is there an opportunity to get this logging-messages on n7k?

View 1 Replies View Related

Cisco Switching/Routing :: Nexus 5000 To Change VLan Port Channel

Jan 29, 2013

I'm trying to change a vlan on a port-channel but I am getting this error when I apply the change:" error: command is not mutually exclusive",I have done this in the past but I cannot remember exactly what I should type to apply the change.

View 2 Replies View Related

Cisco Switching/Routing :: Change Number Of Internal Port-channel On Nexus 5000

Jan 3, 2012

I'm in the middle of a Nexus 5000 project and recognized today while configuring port-channels, that some of the interface numbers are reserved for internal use.
 
Is it possible to change or configure which port-channel interface numbers are allocated for internal use by NX-OS?
 
Unfortunatly I wasn't able to find a solution for this issue in the offical Nexus documentation, the search function of this forum or Google. If I did miss something or didn't look careful enough at the Nexus docs, I'm also happy with RTFM (... fine manual) responses and links to the info :-)
 
Additional info:
 
Nexus5k(config)# interface port-channel 128 ignored port-channel128: internally used, configuration not allowed
 
Port-Channels 111, 113, 115, 119, 121, 200, 211, 222 were created manually, but 127 - 129 were not.
 
Nexus5k# show port-channel usage
Total 11 port-channel numbers used
============================================
Used  :   111 , 113 , 115 , 119 , 121 , 127 - 129 , 200 , 211 , 222
Unused:   1 - 110 , 112 , 114 , 116 - 118 , 120 , 122 - 126 , 130 - 199
201 - 210 , 212 - 221 , 223 - 4096

[Code]......

View 3 Replies View Related

Cisco :: Nexus 5548UP 2248TP To 3650G Vlan1 Trunking

Jun 4, 2012

Got an odd problem with trunking, all vlans except vlan1 trunk perfectly. Link is from a pair of dualhomed FEX 2248TP's to some 3650G Switches. Nexus running - version 5.1(3)N2(1) 3560's running - 12.2(53)SE2 & 15.0(1)SE2

View 3 Replies View Related

Cisco Switching/Routing :: Nx 5548UP After Reboot Log Shows Vpc Down

May 23, 2013

We have a Nx5548up pair connected to FI6248 via a vPC. We had to reboot a FI (in order to configure more FC ports) ; following that reboot, we meet many issues.The first log shows the vPC down showing the FI rebbot.2013 May 23 12:31:45 sw-n5kup-fr-eqx-01 %ETH_PORT_CHANNEL-5 PORT_INDIVIDUAL_DOWN: individual port Ethernet1/2 is down

View 1 Replies View Related

Cisco Switching/Routing :: Packet Discard On Nexus 5020 Link To Nexus 5K

Feb 23, 2011

We are facing issue of continous packet discards On nexus4001L link (int po2) to Nexus5020 switch. Nexus4001L is installed in IBM blade center server and we have FCOE enabled in this setup. [code]

View 2 Replies View Related

Cisco Switching/Routing :: Nexus 7000 With Fabric Extenders Nexus 2000?

Mar 15, 2013

I have been tasked to replace the existing Cat 6500 and 3750 switches by Nexus 7000 and Nexus 2000.I was told initially my boss plans to get 2 x Nexus 7000 and then eventually blow up to 4 x Nexus 7000s.For Nexus, is there a list of tasks / points that i need to consider for building the initial design?
 
Can i just link the Nexus 7000 like the following?
 
N7k-A    =========   N7k-B
|                                   |           
lots of N2ks               lots of N2ks

View 12 Replies View Related

Cisco Switching/Routing :: Nexus FEX Transceivers SNMP MIB Nexus 5000

Dec 22, 2011

Struggle to find the SNMP MIBS of the Nexus 5000 FEX tranceivers.

View 3 Replies View Related

Cisco Switching/Routing :: Datacenter Design With 2 Nexus 5K And 4 Nexus 2K?

Nov 13, 2012

we are planning a Nexus datacenter project with this layout:Our experiences with Nexus switches are not so large until now and the manuals are very extensive.Both N5K´s should be connected directly with all 4 N2K switches. I did not find a layout like this in the manuals. Only a design,where only 2 N2K are connected to one N5K, with this fex config:Now I´m not sure if it is right to make a config like this with the same slots and fex´s or with different slots and fex´s.

View 1 Replies View Related

Cisco Switching/Routing :: Nexus 7010 / VSS - Does It Support Virtual Switching?

Apr 9, 2010

Does the nexus 7010 support virtual switching yet?  All of the posts I have found from about a year ago say that it is going to be supported, but there were no dates listed.  I heard the same thing from Cisco a while back, but haven't followed up with it.If it is supported finally are there any configuration guides available for it?

View 7 Replies View Related

Cisco Switching/Routing :: Facebook Forum Data Center Switching With Nexus 5000

Oct 8, 2012

Lucien is a customer support engineer at the Cisco Technical Assistance Center. He currently works in the data center switching team supporting customers on the Cisco Nexus 5000 and 2000. He was previously a technical leader within the network management team. Lucien holds a bachelor's degree in general engineering and a master's degree in  computer science from Ecole des Mines d'Ales. He also holds the  following certifications: CCIE #19945 in Routing and Switching, CCDP, DCNIS, and VCP #66183

View 1 Replies View Related

Cisco Switching/Routing :: Nexus 5010 Support For Inter VLan Routing

Jan 10, 2012

Can nexus 5010 supports inter v lan routing , as there is no core switch and router available in current network.

View 2 Replies View Related

Cisco Switching/Routing :: Nexus 5000 LAN Routing Connection Deployment

May 16, 2013

We have our Nexus as our default gateway (101.1) and the default VLAN1 is setup with two subnets 101.X and 102.X. The DHCP server is using a superscope setup to accomodate the overflow of devices requesting IPs on 101, so when 101 is consumed persons are able to obtain a 102.X IP address. The setup is basic on superscope. The issue is some times the routing to the firewall with a 102.X is not always 100%. Somedays all goes well and the 102 subnet is routed out to the firewall and its a good day. However, such as today a 102.X address is not routing as it did 24 hours ago. I am perplexed as to why this is behaving unpredicatable. Here is running-config for VLAN1 to show the 102 as secondary address to VLAN1.

View 2 Replies View Related

Cisco Switching/Routing :: Nexus 7010 - Inter-VLAN Routing On Multilayer VPC Environment

Feb 16, 2011

you find attached my network architecture with 2 Nexus 7010 on core layer and 2 Nexus 5020 on distribution layer, each one with 1 N2148T fabric extender switch. PC-A1 and PC-A2 are connected to one N2148T, PC-B1 is connected to the other N2148T. Nexus-7000-1 is HSRP Active for all VLANs, Nexus-7000-2 is HSRP standby. PC-A1 and PC-A2 are connected to VLAN A, PC-B1 is connected to VLAN B. PC-A1 and PC-A2 have the same default gateway correspondent to IP HSRP on VLAN A. It happens that PC-A1 is able to ping PC-B1 while PC-A2 is unable to ping PC-B1. If I issue a traceroute from PC-A2 I see Nexus-7000-2’s physical IP address as the first hop even if Nexus-7000-2 is HSRP standby. After the first hop the traceroute is lost. If I shutdown Port-channel 20 on Nexus-5000-2, PC-A2 starts to ping PC-B1.I can’t understand what’s wrong in this architecture.

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved