Cisco VPN :: 5512x Anyconnect Ssl Licensing For ASA Active / Passive Pair
Aug 7, 2012I am purchasing 2 5512x ASAs to be configured as an Active/Passive pair as a VPN device. Do I need to purchase anyconnect licenses for both devices?
View 2 Replies
ADVERTISEMENT
Cisco Firewall :: ASA5520 - AnyConnect License On Active / Standby Failover Pair?
Mar 6, 2013Our customer has purchased 2 x L-ASA-AC-E-5520= Anyconnect Essentials VPN Licenses (750 Users)Ive installed both activated licenses as per the cisco guides, I didnt get any errors on the install. I did a reload on both, they are both back up and running as active/standby but when I do a sh ver the license still shows "ASA 5520 VPN Plus License"Am I being dumb and has this worked successfully or should it not now display Anyconnect when I do a sh ver?
View 8 Replies View RelatedCisco VPN :: 5512x / RA VPN Using AnyConnect In 2nd Site?
May 14, 2013I am looking into a DR plan where should a primary site go down users with the Cisco anyconnect client will be able to VPN to a second site. The ASA I am configuring is a 5512x for the 2nd site. The main site has a pair of 5510's in a HA pair. Is it possible to setup a secondary Remote Access VPN connection for users to connect to? If I was to configure Anyconnect RA VPN on the ASA on the 2nd I would need to purchase an SSL cert in order to configure this?
View 9 Replies View RelatedCisco :: What Is Active / Passive Port-channel
Feb 7, 2013what is active/passive port-channel..? and how it will do load balancing when my network traffic is flowing on both the ports.
View 5 Replies View RelatedCisco Firewall :: Cannot Use FTP Passive / Active Of ASA5505
Sep 12, 2011Users cannot download some files from a FTP in a software over VPN Explanation users work with a program and inside the program they download claim (the software goes to the FTP and download the file)
But the program returns an error 3018 in FTPGET. If the user goes to the old PPTP VPN it works like a charm so the problem is the Cisco VPN.
I cannot post my complete config but we use the filter vpn value to associate a special access-list to a user.
The user that has this problem has this as an access-list.
access-list 201 extended ip permit 10.250.128.0 255.255.255.0 192.168.202.0 255.255.255.0
I've made some research and i've added this info
policy-map global_policy
class inspection_default
Inspection ftp
Still doesn't work.
I have to add that normally the internal network is 2.0 and not 202.0 but since we have user with 2.0 at home we had to do this.
So when a user sends a request to 202. the cisco fowards it to the Juniper inside the network and it translate it back to 2.0 Also that is the ONLY thing that doesn't work. The client can work all day on that program and it will work #1 exept when she does the claims
I am also been working on this VPN for 2-3 months without any problems.
Cisco WAN :: 5520 - Active / Passive ASA With Redundant ISP Connections
Apr 25, 2012Currently we are using a single connection to our ISP and in the coming months will be moving to a two seperate connections (to same ISP). In our current setup we utilize active/passive ASA's (5520, single context) and would like to utilize that going forward as well, the reason being is our DMZ's all hang off of these ASA's and we have fiber connectivity between our datacenters.Our main datacenter and DR Datacenter are basically one big LAN with fiber between them, so we have our DMZ networks at both locations currently with both terminating in our ASA's. That way if the ASA at our current site fails the DMZ's are still accessible via the secondary firewall at our DR facility.
View 1 Replies View RelatedCisco Application :: ACE 4710 - Active / Passive Failover?
Nov 14, 2012We have an ACE 4710 that has two web servers in an active/passive scenario. The issue is that if node 1 fails and node 2 takes over connections to node 2 stay active even if node 1 becomes available again. Is there are way to ensure that node one is not placed back into service if it becomes available again.
how active/passive failover shoudl be configured, so I can make sure I have it set up correctly;
Cisco Firewall :: ASA 5510 Active / Passive Failed
Jan 12, 2012i have a problem with a Failover Pair of 5510. The Boxes run with the software version 8.2.5.
If the Active ASA goes down, the Standby ASA switch to Active.
If i switch on the old Active ASA, both ASA are Active. This problem don't solved with the command 'no failover active' on the Standby box. This problem only solved with the command 'no failover' and then 'failover' on the Standby box.
Cisco WAN :: 2921 - Network Design With BGP And Active / Passive ASA's
Mar 1, 2012The following diagram is showing what I "Plan" on doing or "Hope" I can do. This is the most complicated deployment I have taken on in my profession, and Honestly it is very exciting, but had some questions.
1. The network between the ASA's and Routers, is that suppose to be a Private network or Public Network? I have to assume Public because I want my ASA's to take care of the NAT.
2. ASA's are runing single context Active/Standby so what way will the ASA push out going traffic?
3. The routers need to know about each other in a BGP configuration, correct? We accomplish this using iBGP so will that traffic need to be allowed through my firewall to allow the routers to share that information, or should these routers be talking to each other outside the firewalls?
Is this design possible? I am sure there are limitations as always, just trying to wrap my head around the flow of traffic and where to start.
Additional Details/Requirements -
BGP routers are 2921's that I have control of. Both routers have 4 port GigEtherswitches in them.
ASA's are Active/Passive and cannot be Active/Active due the limitations of the Active/Active Design (VPN limitations)
Both ISP's must be used for outbound traffic, I would like to be able to load balance, but can send some traffic one way and the rest of the traffic the other way based on Routes.
ISP's are not Symentrical, one is 50mbps and the other is 250mbps.
All NAT should take place at the ASA's
Additional Questions:
The routers that have gig etherswitches, can they run HSRP?
Should I be putting Layer 3 switches between the routers and the ASA's instead?
Where should I run my iBGP communication for the routers?
Cisco Firewall :: ASA 5520 Needed To Be Configured In HA Active / Passive
May 24, 2011I have the following Setup, Two Cisco ASA 5520 needed to be configured in HA Active/Passive. The Firewalls includes also AIP module. Does the ASA 5520 will internally make the AIP modules also HA Active/Passive? Is there a document regarding the issue? Is there a seperate license for the AIP modules for HA scenario?
View 1 Replies View RelatedCisco Security :: Adding 3 Node ASA5510 / Active / Passive Cluster
Jul 25, 2012we operate an active/passive cluster with 2 ASA5510 in Routed Mode. Is it possible to add another node, so that we have one active and two standby nodes in the cluster? Unfortunately, I have found no documentation on this .... The data sheet say only up to 10 nodes can be mentioned as a VPN load balancing cluster.
View 1 Replies View RelatedCisco Firewall :: ASA 5520 - Interface Reconfiguration In Active / Passive Failover
Dec 20, 2011Currently l have two ASA 5520's in a active/passive failover scenario. Currently the interfaces for the inside and outside are fixed at 100/FULL.I want to repatch them into GigE ports setup as Auto Negotiate.Is there anyway of keeping the connections through the firewall active in this type of scenrio or will l have downtime disconnecting and repatching? or could l possibly disable failover and reconfigure each ?
View 6 Replies View RelatedCisco VPN :: ASA 5510 - AnyConnect Licensing With IP Phone
Feb 21, 2013 I am just getting more confused the more I try to work it out. Not sure if this goes in the IP Telephony section or here. We have an ASA 5510 with the base license. We are needing to install IP Phones at remote workers homes, and I understand there are Cisco IP phones which have VPN clients built in to allow a tunnel to the central private network. IT appears that you can only use Any connect VPN for this, ans I am trying to work out what licensing upgrade we need to apply to the ASA, as the two Any connect licenses you get free on the ASA is not enough.
This is the phone we are looking to get; {URL} . What I want to know is will the Any connect Essentials license work with these IP phones? When I do a show version,
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 50
Inside Hosts : Unlimited
Failover : Disabled
[code].....
This platform has a Base license. It shows "Any Connect for Linksys phone : Disabled", is this the same for Cisco IP Phones? Is this the specific licensing type I should be looking to get for Any connect on IP phones or will Essentials do?
Cisco VPN :: ASA 8.4(1) AnyConnect Premium User Upgrade Licensing?
Feb 22, 2012Prior to version 8.4(1) Cisco called their licensing name for SSL/VPN users AnyConnect Premium SSL VPN and currently the new name of the licensing is simply AnyConnect Premium. Also, the IOS display name for the amount of SSL/VPN users enabled via your licensing (ex. 2, 10, 25, 50, ...) by running a 'show activation-key' was changed from SSL VPN Peers to AnyConnect Premium Peers.With that said, my question is if the license for upgrading 10 users to 25 users (L-ASA-SSL-10-25= - ASA 5500 SSL VPN 10 to 25 Premium User Upgrade License) on an ASA prior to 8.4(1) and an ASA with 8.4(1) is still valid and the correct part number to peform these upgrades for both ASAs. The description of this part number is throwing me off because it says SSL VPN to Premium User, which was the name prior to 8.4(1). I could not locate any documentation regarding this part number or upgrading 10 users to 25 users for both ASAs.
View 4 Replies View RelatedCisco VPN :: ASA5505 IPad AnyConnect Mobile Licensing
Sep 13, 2011I am setting up an ASA5505 to allow a VPN with certificate from AnyConnect Secure Mobility Client (iPad)However I get a "No License" message back from the ASA, on the iPad - Anyconnect.I remember reading the ASA5505 came with two licenses.
View 8 Replies View RelatedCisco Firewall :: ASA5500 - AnyConnect Vs IPsec VPN Client Licensing
Sep 19, 2011I was wondering if it is needed to license the IPsec VPN clients in the ASA5500 firewalls...I know that you have license the SSL VPN peers (AnyConnect). I am almost sure that for the IPsec you don't have to.
View 1 Replies View RelatedCisco Firewall :: IPS Modules In ASA5510 Active / Standby Pair
Feb 6, 2012I am looking to add the IPS module to my ASA 5510's. I am contemplating only purchasing one module and placing it in the active ASA. I am willing to accept that in a failure scenario I will loose the IPS functionality until the primary ASA is recovered. I have not had a chance to talk to my SE to see if this is even possible. Has anyone attempted a deployment such as this? Will it work and is it supported?
View 3 Replies View RelatedCisco Firewall :: Can Upgrade Active / Standby Pair From 7.2(4) To 8.0(5)25 Directly
Jan 17, 2012Can I upgrade Active/standby pair from 7.2(4) to 8.0(5)25 directly or need to upgrade to 8.0.2/4 first? Upgrade an Active/Standby Failover ConfigurationComplete these steps in order to upgrade two units in an Active/Standby failover configuration:Download the new software to both units, and specify the new image to load with the boot system command.Refer to Upgrade a Software Image and ASDM Image using CLI for more information.Reload the standby unit to boot the new image by entering the failover reload-standby command on the active unit as shown below:active#failover reload-standbyWhen the standby unit has finished reloading and is in the Standby Ready state, force the active unit to fail over to the standby unit by entering the no failover active command on the active unit.active#no failover activeNote: Use the show failover command in order to verify that the standby unit is in the Standby Ready state.Reload the former active unit (now the new standby unit) by entering the reload command:newstandby#reloadWhen the new standby unit has finished reloading and is in the Standby Ready state, return the original active unit to active status by entering the failover active command:newstandby#failover activeThis completes the process of upgrading an Active/Standby Failover pair.
View 10 Replies View RelatedCisco Firewall :: ASA 5540 - Active / Standby Failover Pair
Apr 13, 2011I currently have two 5540's in an Active/Standby pair. The primary unit failed on February 12th, so the secondary ASA is now the active one. My question is this - we have made a lot of changes since February 12th and I am planning on fixing this failover issue over the weekend. Will the secondary (now active) FW sync it's config to the non-active FW, or will the failed FW sync it's out-of-date config - removing any changes that we've made in the last month or so.
View 1 Replies View RelatedCisco :: Citrix NetScalar Vs Anyconnect On A Pair Of 5540s
Oct 30, 2011My colleague wants to use our load balancers for VPN. We are coming off 3030s which are serving remote access IPSec as well as terminating LAN to LAN tunnels for like 7 sites.I want to secure the 5540s behind our front end 5585Xs when we move prod to the new dc.We have no immediate need for clientless but need to support osx lion and IPSec client does not. Thats all that's driving this effort currently. I already reminded mgmt that the 3030 and the IPSec client are end of life.I just think anyconnect is the better solution based on current skillset and the popularity of the solution.
View 2 Replies View RelatedCisco Security :: Pair Of 5520s Running 8.2(3) In Fail Over Active / Standby
Jun 29, 2011I have a pair of 5520s running 8.2(3) in failover active/standby, routed mode. I have an issue with SSH as it's stopped worked after a short time, less than 8hrs during the network being installed, telnet is working fine as is https/asdm. I have re-created the crypto key and the ssh access is allowed. When I try to connect I just get a flashing cursor, telnet to the ip and port 22 also works.
View 1 Replies View RelatedCisco Firewall :: ASA 5505 Security Plus Licenses - HA Pair Using Active / Standby
Apr 24, 2012I have two ASA 5505's with Security Plus licenses on both.I am trying to force them to becoming an HA pair using active/standby.When I enable failover I get this message:
Mate's license (Licensed Cores ) is not compatible with my license (Licensed Cores ). Failover will be disabled.Do I need to apply new licenses to the ASA's?
Device licence details (same on both):Cisco Adaptive Security Appliance Software Version 8.2(1) [code] This platform has an ASA 5505 Security Plus license.
Cisco Switching/Routing :: 6504 VSS Pair Shows Active / Standby On Led But Not In Config
Oct 30, 2012After rebooting a pair of 6504's configured for vss, both switches show active on the sup modules. A show switch virtual redundancy however shows the pair working in an active/standby mode. We have 6509's in vss pairs and they show active on switch1 and standby on switch2 led's. For the 6504's switch 1 was booted first and then the second switch about 30 seconds later. Is there something different with the 6504's? [code]
View 4 Replies View RelatedCisco Security :: Implement Active / Standby Cluster With A Pair Of 5550 ASAs?
Aug 19, 2012I want to implement Active/Standby cluster with a pair of 5550 ASAs and I have a licensing question. Here is the "sh activation-key detail" output from both devices...
ASA1:
sh activation-key detail:
Serial Number: XXXXX
No active temporary key.
Running Activation Key: XXXXX XXXXX XXXXX XXXXX XXXXX
[code]....
This platform has an ASA 5550 VPN Premium license.The flash activation key is the SAME as the running key.So it looks obvious that I'll have to upgrade the first ASA to support 25 SSL VPN Peers in order to build HA cluster, right?Now I want to know do I need the "ASA5505-SSL25-K9" license or something else.
Cisco Firewall :: Monitoring ASA 5505 Firewall Active / Standby Pair Using SNMP?
Sep 7, 2011How I can actively monitor the interfaces and overall status of 2 x ASA 5500s in an Active/Standby configuration?
I can setup monitoring of the interfaces on the Active member but I'm not sure how to manage the Standby member?
Cisco AAA/Identity/Nac :: Setup AAA For Anyconnect With Active Directory On Asdm 6.4
Aug 20, 2012Im sure this has been asked before but a quick search has not yielded any exact results so here goes
I have anyconnect up and working great on for vpn users using local authentication. Im going over the white papers and seeing a lot of options for NT domain, LDAP, tacacs+ etc
we would like remote vpn users to autherticate using their windows domain password, but Im not sure which would be the easiest and quickest option to configure, and I cant find a guide for asdm setup for this topic that doesnt cause more questions than answers . The white papers Im finding are confusing since I am a rookie at this topic.
what is the easiest/quickest way to setup windows domain authentication via asdm?
Cisco VPN :: ASA5510 / AnyConnect Active Directory User Password Expiration?
May 20, 2012I have a Cisco ASA5510 firewall that has SSL Web VPN functionality and is utilizing AD Server as Authentication server for users.However, we have a policy to change password at certain point of time. Users in the office have no problem. They just login their PC and change password. Users outside of office is a pain when their password is expired. Is it posible for them to change their AD password thru VPN using Cisco Anyconnect?
View 2 Replies View RelatedCisco :: ASA5510 - AnyConnect VPN Active Directory User Password Expiration
May 19, 2012I have a Cisco ASA5510 firewall that has SSL Web VPN functionality and is utilizing AD Server as Authentication server for users. However, we have a policy to change password at certain point of time. Users in the office have no problem. They just login their PC and change password. Users outside of office is a pain when their password is expired. Is it posible for them to change their AD password thru VPN using Cisco Anyconnect? If yes, can you show me how?
View 1 Replies View RelatedCisco Switching/Routing :: Pair Of N7K Distribution Switches Connected To A Pair Of Aggregation Switches
Mar 11, 2012We have a pair of N7K distribution switches connected to a pair of N7K Aggregation switches.We run vPC on both pairs of n7k's.
-n7k-d1 has two interfaces in a Port-Channel connecting to n7k-a1 & n7k-a2. (PC1)
-n7k-d2 also has two interfaces in a Port-Channel connecting to n7k-a1 & n7k-a2. (PC2)
My problem is that Spanning-Tree is blocking PC2 and all traffic from n7k-d2 is traversing the Peer-Link before reaching the Aggregation layer. Is this the best design for connecting two pairs of n7k's with vPC or if a better design would be to connect all 4 links into the same Port-Channel and vPC?
Cisco Firewall :: ASA 5520s From Active / Standby To Active / Active
Jul 17, 2012I have a pair of ASA 5520s operating in failover pair as active/standby, having two contexts on them. I am planning to share the load and make it active/active making first context active on the primary unit and second context active on the secondary unit. My question is if this will disrupt any connectivity thru these firewalls when I do "no failover" on the active/standby and assign the contexts to different failover groups and enable the failover back.
View 6 Replies View RelatedSplit A Single 4 - Pair Ethernet Connection Into Two 2 - Pair Ethernet Connections
Dec 28, 2011I've got a router on which I run a backup/media/print server, a couple of computers and a voip box. My router has only four ethernet lan sockets which are thus all occupied by the above, but I need to attach at least one further device b
Secondly, could a splitter such as >> this one << do the job? I'm guessing this basically split a single 4-pair ethernet connection into two 2-pair ethernet connections.
Cisco Firewall :: Upgrading From PIX To ASA 5512X
Mar 12, 2013We are in the middle of upgrading from two PIX's to some new ASA5512X's. To give you some background on the situation we are upgrading these since the PIXs are fairly old. We had one extra that we had to use since one PIX has failed already. The guy that implemented the PIXs orginally was learning how to do so as he went so there is alot of needless config in the PIX, atleast from what I can tell. Another guy that works with me has done some configuration on the new ASAs and has done the majority of it so far. Today we went to install the new ASAs and switch everything over hoping it would work, but that didn't happen. It seems that there is something wrong with our NAT and ACLs somewhere along the lines. The way our network is laid out is that we have two school campus with a site-to-site VPN one is 172.17.0.0/16 and the other is 172.18.0.0/16. We also have a remote-access VPN on both ASA's. When we connected the new ASAs up and brought up the interfaces, nothing on the inside could ping the internet nor the other side. The VPN showed active on the ASA's and each ASA could ping the others outside interface, but that was it. I have posted the configs below.
ASA1:
: Saved
: Written by enable_15 at 04:26:18.240 CDT Tue Mar 12 2013
!
ASA Version 8.6(1)2
[Code].....
Cisco Firewall :: ASA 5512x No Internet Connectivity
Jul 8, 2012I am updating my 8.2(3) code for my new ASA5512 that is running 8.6(1) and am unable to get on the internet with my current configuration from the inside interface.
Information:
Outside: ***.***.33.11
Gateway: ***.***.32.9
Inside: 192.168.215.0 /24
dhcp 215.100 - 150
[Code] .....