II have a management network 192.168.5.x and VPN network 192.168.25.x. I can ping a all my network elements except to firewall (ASA5510). The ASA has the IP 192.168.5.1. I think that the firewall has some restriction but I don't know. I have 8.2 software and any connect 3.0 and work fine. If I am in the management network (192.168.5.7), I can ping to firewall. The restrict is with the VPN network.
View 4 RepliesI am simulating Anyconnect VPN connection in the lab.I have an issue while configuring Anyconnect VPN on ASA5510.
I can have a successfull anyconnect connection but i can't ping my firewall Interface IPs while i am in the connection.
ASA 5510
Outside IP: 192.168.1.1/24
PC connected to Outside Interface: 192.168.1.10/24
Inside IP:10.10.10.1/24
PC connected to Inside Interface: 10.10.10.100/24
Pool : 10.20.20.11 - 10.20.20.50 /24
I have a successful VPN connection & the PC connected to the outside Interface gets an IP address from the assigned pool (10.20.20.11 with default gateway of 10.20.20.1).But i can't reach (ping/telent) to the ASA while I am on the anyconnect VPN connection.
I beleive it is mostly due to NAT/Routing issue..
I have a vpn ssl remote access with a fw asa 5510 version 8.02. When users use any connect vpn ssl they in the Lan can access to the servers,but they can not access using ssh or telnet to inside fw asa.
aaa authentication ssh console LOCAL
ssh 0.0.0.0 0.0.0.0 outside
ssh 0.0.0.0 0.0.0.0 inside
ssh timeout 30
Our Cisco ASA 5510 running 8.4(4)1 just started dropping packets and our AnyConnect clients are seeing horrible performance. The system is extremely slow compared to just a couple days ago.Nothing has changed on the system. I can post the configs if needed.
firewall# sho int
Interface Ethernet0/0 "outside", is up, line protocol is up
Hardware is i82546GB rev03, BW 1000 Mbps, DLY 10 usec
Full-Duplex(Full-duplex), 1000 Mbps(1000 Mbps)
Input flow control is unsupported, output flow control is off
Description: == WAN Interface ==
[code]....
I have done a "sho vpn-sessiondb detail svc" and I can see the dropped packets of the individual users, but cannot see why the packets are still dropping.how I can correct this and restore speeds?
We have 2 ASA 5510's running in a Active/Standby configuration. It appears that most of the changes we make on the active unit are replicated to the standby unit. However, there are 3 AnyConnect Client Profiles on the active unit and none of them show up on the standby, the standby has no AnyConnect Profiles. We also have 1 OnConnect script on the active unit and it does not appear on the standby unit either.
I was under the assumption that all config items on the active unit would replicate to the standby. Is this not correct? Do I need to do something extra to get everything replicated? Are there other items that do not replicate?
So, I've set up Anyconnect client access to an ASA-5510.
I've got a handful of interfaces, which contain hosts that should be accesible to anyconnect clients. I'm unable to reach addresses on a specific network, due to what packet-tracer claims is an implicit deny, though I'm unsure where to apply an access-list in this case.
fw1# show nameif
Interface Name Security
Ethernet0/0.205 SECURE 90
[Code].....
I currently have an ASA 5510 unit. I have a dmz setup which house some web servers and an inside interface. The web servers contain multiple public ip addresses which I have natted and access is fine.What is the most simple way to enable ping for my dmz from the outside. Meaning if someone outside the network pings one of the servers by its public ip address I would like it to respond to ping.
View 1 Replies View RelatedBackground: I have a couple of ASA 5510's I'm going to put in our lab environment. I have restored them to default config and set up the m0/0 interface with an ip/mask and started the http server. My lab environment is on the 10.45 subnet and my .com corporate environment is on the 10.40 subnet. I've also setup DNS and, from the ASA, can ping anything in the 10.45 subnet.
The problem, is that from the ASA, I can not ping the internet or my 10.40 subnet. And vice versa, I cannot ping the ASA from my 10.40 subnet. When I bring up a regular server, there is no special configuration I need to do as those subnets talk to each other and nothing is restricted.
Is there something special I need to do go get it to work? I tried adding a access list to allow icmp, but that didn't seem to work.Oh, and I'm getting to the ASA by RDPing into a lab server (on 10.45) then putty to the ASA.
I have recently made some chages to my ASA 5510 (not sure what) I was previously able to ping url... and I am now not able to ping anything on the Internet, but The Internet connectivity work perfectly.
View 7 Replies View RelatedI ran into a very strange icmp ping issue. The network has been working fine other than the issue listed below, L2L VPN works fine and all three data centers can access each other via L2L VPN.I have three ASA5510. [code]
View 5 Replies View RelatedThe VPN will connect.I can ping and connect to the ASA 5510 on it's LAN interface.My problem is that I cannot ping or access anything on the LAN past the firewall. What am I doing wrong?
Here is my config.Result of the command: "show config"
Saved
: Written by enable_15 at 22:55:02.299 UTC Tue Jan 10 2012
!
ASA Version 8.2(5)
!
hostname ********
[code]....
The ASA is configured in very simple transparent mode. As desired, traffic can flow in each direction between inside and outside. I can manage the ASA via console and direct connection to the management interface. The problem is that I cannot ping or ssh to the ASA via the inside interface. I need to be able to manage the ASA from any PC on the inside LAN. I suspect I am missing some easy aspect of the configuration but after a lot of hours I'm about at the end of my patience with it. Here is what I believe to be the relevant parts of the config.
ASA Version 8.2(1)
!
firewall transparent
hostname issr1
enable password 2alej83t5cqT0FWd encrypted
passwd 4kleUY438I93.4ljdh encrypted
names
[code]....
We have two ASA5510s, each with outside interfaces to the same two ISPs (different IP addresses within the same subnet, of course). Both ASAs allow ICMP on all (inside and outside) interfaces. One ASA's default route is to ISP-1 and the other is to ISP-2. We can ping the default gateways for both ISPs from only one ASA. From the other ASA, we can only ping the default gateway for the default route but not the other. The pings originate from an inside client, first configured with the default gateway for ASA-1, then for ASA-2. Why does this happen, how do I troubleshoot something like this and how do I fix it?
View 1 Replies View RelatedI was trying to add an Access Rule then Nat rule, they applied ok then i lost connection to my ASA 5510.I cant ping device ip, i cant connect via console , only can acess via Management port, i have pasted Running config. [code]
View 4 Replies View RelatedSwitching out a 5510 as our primary firewall with a 5520. I've essentially copied the working config from the 5510, and put it on to the 5520, making small changes where necessary. Plug everything. I cannot get out to the internet.
Facts:
-All interfaces have no shut on them
-No machine can ping out to the internet gateway
-All machines can ping out to the inside interface of the firewall
-It's not a problem with the internet because I can take a laptop, enter in our outside interface information, plug it into the internet gateway, and I can get out to the internet just fine.
One of my client has BSNL leased line with LAN IP POOL we configured those on ASA 5510 nad Internet working fine but from cloud we are not getting any response for ping requiest please find running configuration below:
ciscoasa(config)# sh run
: Saved
:
ASA Version 8.2(1)
[Code]....
I recently added a business cable modem to relieve some of the congestion I was getting on my T1 for our MPLS network. There was an ASA 5510 collecting dust in a closet here and I thought it would be the perfect device for firewalling the traffic coming in from the Cable modem, and handling the routing of our internal MPLS traffic as well. Internet setup was cake. The test laptop I have using the ASA as it's gateway has great internet service but it cannot ping across either of our MPLS networks. I have one MPLS with AT&T and one MPLS with EarthLink. My hope was to use the cable modem as the Default route for all unspecified internet traffic and route our internal MPLS traffic to the cisco 2800 routers that are currently in place for the MPLS. I can ping across the MPLS when I telnet to the ASA, but I cannot ping across the MPLS from the client that is connected to the ASA.
Here's the topology I'm working with
Internet
|
Cable Modem
|
ASA 5510 10.52.120.23
[Code].....
We are using an ASA 5510 and remote access (SSL VPN) using the AnyConnect client.
Is it possible to display a user message when a user connects using the AnyConnect client, matching a specific dynamic access policy? Can the message be displayed when the action is "Continue" rather than "Terminate"? I can't seem to get this to work and wondered if there was a LUA function to do this.
We have a DAP which gives a restricted ACL when the user's anti-virus is out of date, and I wanted to notify the user to update their anti-virus and reconnect.
I setup and SSL anyconnect VPN on my Cisco ASA 5505. It works well and connects with out a problem. However, I can't ping any internal clients, but I can RDP to them. Most of the time people end up posting their config so I will as well.
MafSecASA# show run
: Saved
:
ASA Version 8.2(1)
[Code].....
We have configured a Cisco ASA 5505 with AnyConnect access. This works great. However, these users cannot seem to ping devices on the private network. We have configured all devices on the network with a 10.10.10.0/24 address space. The inside interface of the ASA i 10.10.10.1/24 and the VPN return addresses are 10.10.10.50 - 10.10.10.65/24.They users can utilize SSH and Oracle or MySQL calls but cannot seem to ping. Obviously, I am over looking something.
View 2 Replies View RelatedI am facing problem connecting via vpn to my asa5510 using anyconnect.My anyconnect client shows "network access: unavailable - no networks detected" before i attempt to establish my vpn.Upon establishing vpn, i was prompted username and password which went through but i was given the error "anyconnect was not able to establish a connection to the specified secure gateway. Please try connecting again".I face this problem after replacing my pc. I was able to connect without problems on my previous pc.The vpn connection uses cert which i have already import to my new pc and authentication is fine since no authentication error. No changes made on my firewall.
View 1 Replies View RelatedI have an ASA 5510 I'm trying to use as an SSL VPN provider. I have Anyconnect windows and mobile licenses from Cisco. I'm looking for a straight forward configuration guide to use. Right now I only need to iPhone and Android clients to work with the VPN, but in the future we might add windows clients.
I was going to use this guide: [URL]. Until I talked to Cisco tech support, they recommended I use the following:[URL] Which is a lot longer and a bit unclear about the whole process, and also points me to this guide:[URL]Which is longer still, and not applicable for the most part.So, what's going to be the best guide to use? Did I have it right the first time? Do I need to go to another site to find something?
we have ASA 5510 with IPS and base license. Now we need Anyconnect support for more than 2 users.
Is for Anyconnect (tunnel-mode) only the Anyconnect Essentials license enough? Do I need a license for SSL VPN peers? What about Anyconnect clientless, I see that I need a premium license? Is this one enough ASA5510-SSL50-K9? It is really expensive in comparison with Anyconnect Essentials.
Here is my sh ver output:
Licensed features for this platform:Maximum Physical Interfaces : Unlimited Maximum VLANs : 50 Inside Hosts : Unlimited Failover : DisabledVPN-DES : Enabled
[Code]....
I have an internal application which requires operators to have a static IP address. I'm looking for a way to do this for our VPN users. At the moment they are given a random DHCP address from a pool. Is there an easy way to get a static address assigned to VPN users on a Cisco ASA5510 any connect VPN?
View 3 Replies View RelatedCan anyconnect clients and cisco vpn ikev1-2 clients use the same certificate on an ASA 5510 ?
View 4 Replies View RelatedWe have an ASA 5510 running 9.1 and the latest 3.1 AnyConnect package for Linux. The problem that i am having is that the AnyConnect VPN will drop after maybe 30 seconds or less of connection. It will connect fine. I can ping my remote servers. Then it will drop and go into a "Reconnecting State". Of which it will not reconnect. I have to close AnyConnect and then try to connect again. Then I'll get the same results. We have about 25 employees that use the AnyConnect VPN all day on Windows 7 machines without any problems. The issue appears to be isolated to my Ubuntu laptop. I have gone so far as to completely reinstall Ubuntu, both 64 and 32 bit versions but end up with the same results.
View 2 Replies View RelatedI have configured an Asa 5510 as SSL vpn gataway ver 8.2(4) Anyconnect Essential. The clients are authenticated via Radius and OTP password.All work well since yesterday. When I have did same configuration changes. My objective was has that the clients accept the self signed certificate issued by the Asa whitout give the warning about the private cert.
So I have try to generaste a new certificate with FQDN equal to myasa.mydomain.com and also a CN=myasa
Then I have change the profile XML file of my anyconnect in this way: [code]
I have a PC at home which is dedicated to one specific task, and need it to be connected to our company VPN at all times. This PC gets accessed by another remote worker (RDP), through the VPN.
This works fine with the PC at my home office connecting via the Anyconnect client... for a few days, then mysteriously disconnects and doesnt automatically reconnect, with the following Anyconnect error;
"The vpn connection to the secure gateway was disrupted and could not be automatically re-established. A new connection is necessary, which requires re-authentication".I have to manually reconnect and re-enter the password, after which it connects fine.
I have looked on the central ASA5510 (which all clients connect to) and set the idle timeout to unlimited for the appropriate AnyConnect profile and group policy, I cant seem to find any other settings to allow it to stay 'always on' from the client.
I am wondering (but am not sure if this is the problem) if it is perhaps because I am on a normal home broadband connection, which uses a dynamic IP, not static. My ISP (Sky) cannot provide a static IP for my public interface..
We have a SSL Gateway setup with the anyconnect client.We have picked up on some of the Windows 7 Tablets that you can install via the web page.Once installed you are connected to the network.However once you disconnect, and try with the anyconnect client u get the following error;
" Anyconnect was not able to establish a connection to the specified secure gateway. Please try connecting again"
We have not seen this on any of the Windows 7 laptops nor Windows XP.
The URL have been added to the trusted zones.We have gone as far to disable anti-virus / windows firewallDisabled the "Protected mode" with in internet explorer.
Anyconnect client version 2.5.3055..ASA 5510 Serial number JMX1504L05Y - ver asa841-k8
I have a problem with my AnyConnect clients connecting to an AD network via a 5510. Anyconnect VPN clients provide AD plus a one time passcode to authenticate to the 5510. This works fine apart from 3 things:
1. Once the VPN session has been established the user is further prompted for AD credentials when accessing an AD share for the first time. Once they provide the credentials the share can be accessed. Should the AD credentials not be passed through when the VPN connection is established? Or is this by design? What makes me think it's not be design is the fact that this could be related to problem 2.
2. Group Policy Update (windows gpupdate) fails. This again suggests to me that the full client/server relationship is not fully in tact.
3. In order to get Outlook to connect to exchange I've had to change Outlooks security settings from Negotiate (which would naturally choose Keberors), to NTLM. Not sure if this is related or not.
Note: DNS is functioning with out any problems
Maybe the first 2 issues are by design, but I thought the whole idea behind the AnyConnect VPN was that the remote machine would function as if connected to the LAN?
I am trying to load the anyconnect VPN client package v3 for windows and Mac on ASA 5510. The ASA has 256MB for RAM and Flash. After I uploaded pkg files and selected the 2 files and applied from ASDM, ASDM spots responding...
I tried to tftp the running config from ASA to my laptop to analyse but got "No memory available" message...
So it seems like the "unzip" process of the pkg files used up memory... what is really the requirement of the mini Memory/RAM on ASA for hosting anyconnect Clients for 2 OS platform? Requirement on Cisco web site is kind of vague.
I am just getting more confused the more I try to work it out. Not sure if this goes in the IP Telephony section or here. We have an ASA 5510 with the base license. We are needing to install IP Phones at remote workers homes, and I understand there are Cisco IP phones which have VPN clients built in to allow a tunnel to the central private network. IT appears that you can only use Any connect VPN for this, ans I am trying to work out what licensing upgrade we need to apply to the ASA, as the two Any connect licenses you get free on the ASA is not enough.
This is the phone we are looking to get; {URL} . What I want to know is will the Any connect Essentials license work with these IP phones? When I do a show version,
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 50
Inside Hosts : Unlimited
Failover : Disabled
[code].....
This platform has a Base license. It shows "Any Connect for Linksys phone : Disabled", is this the same for Cisco IP Phones? Is this the specific licensing type I should be looking to get for Any connect on IP phones or will Essentials do?
I have a 5510 using AnyConnect VPN clients. I have a DNS name for my router to accept connections ie cisco.mydomain.com..I can ping the address by hostname from the clients machine ok but when the AnyConnect client opens it has my hostname ie (cisco.mydomain.com) but says "invalid host entry" I have to type in my IP address for it to connect.I have the hostname in my AnyConnectProfiles.xml.
View 1 Replies View Related