I have an old VPN 3000 Concentrator that I do not have any idea what is running on it. The previous network admin didn't leave a password for it, so I tried to reset the password. I was successful in doing so, but when I try to access it with the default of admin/admin via web browser, I still cannot access it. I am loathe to remove or power off this device without knowing what is on it.
View 6 RepliesI have been trying to setup a LAN-to-LAN VPN between two sites that are using a 3000 series CISCO Concentrator. After following the basic setups from the CISCO site, I am still unable to create a tunnel. At the moment I'm starting to believe it is how I have physically setup the network. Site 1 is using a Billion BiPAC 7404VNPX ADSL2+ Modem, Site 2 is using a Netgear DGN2000 ADSL2+ Modem, The VPN Concentrators are setup behind these devices with each firewall setup to allow the needed ports forwarded.
View 5 Replies View RelatedOur VPN 3000 concentrator's admin password was changed by somebody so i reset the password by using straight through serial cable, now the problem is it allows me to login with admin through console but not through admin web interface or telnet. I have enabled telnet and http access but still no success. Concentrator is using internal database so no AAA server is configured.
View 1 Replies View RelatedI have a client who saw there was a android version of the AnyConnect client and want me to go through and get their VPN 3000 Concentrator confingured to be able to connect in with it.
The Conncentrator is currently setup several groups of users and the base group is set up to all other products to connec tin via a pre shared key. It took alot research to get it configured to this point and all the searches i pull up are for a ASA.
I have a VPN Concentrator 3000 with LAN-to-LAN DES-56 connections connected to it (Cisco PIX 506). Everything was working fine and then over the night something messed up on it. No settings were changed or anything.
First issue was anything using DHCP (getting IPs from the sites local PIX) couldn't be pinged or reach out through the Concentrator. It was only Thin Clients that didn't work. I could still ping the PIX, printers and desktop computers that were static set IPs. But this was happening at every site going through this Concentrator. The sites going through out MPLS network are fine.
I tried setting the Thin Clients to a static IP but still couldn't ping them.
I then decided to reboot the Concentrator, when it came back up all sites reconnected back to the Concentrator but now couldn't ping anything at the sites, not even the LAN IP of the PIX (or printers and desktops now). I power cycled a few of the sites PIXs but they still were not pingable even though the Concentrator showed they were connected.
I then decided to physical power cycle the Concentrator, it's back up and all sites are connected but none of the devices on the LAN side are reachable.
The Concentrator can ping the sites WAN IP but nothing on the LAN side going through and out the Concentrator. It can ping the LAN through the private interface (going back towards my LAN) just not going through the public interface (over the WAN).
The sessions show that Bytes are Rxing but no Bytes are Txing.
I have 3000 concentrator in 192.168.1.x/24 network (concentrator has static IP of 192.168.1.4/24 assigned to its private int). I can manage it thru HTTP from any PC in the same subnet, but connection failes while trying to connect from PC on different subnet (i.e. 10.1.1.x/24). Is there ACL in concentrator config which needs to be modified to allow management from different subnet?
View 2 Replies View RelatedOur enterprise uses a VPN Concentrator 3000 for our VPN access. Is there a way to view a log history of what user connected to VPN and what IP address they were assigned? It would be for 2 days ago which was over the weekend.
View 3 Replies View RelatedI've the following scenario VPN Concentrator is connected to a router which is connected to a router and at the edge Cisco 515E PIX is connected to the internet. The problem is that the normal VPN Dial-up connection (a utility of windows) are getting connected but Cisco VPN Client throws error 412. Here's what I've tried (Initially groups and user were created):
(1) Allowed port 10000 on PIX ( access-list from-outside-coming-in permit tcp any host <public ip> eq 10000) and checked IPSec over UDP on VPN Conc. under Mode Config tab. Also checked IPSec over TCP tab under tunneling panel at port 10000. Tried connecting through VPN Client but it threw error 412
(2) In the reference guide, I read that IPSec over NAT is allowed on ports ranging from 4000 something to 40000 something.
I tried 33333, both on PIX and VPN Conc. under Mode Config tab but still no use. Same error 412.
is it generally possible to configure a site to site VPN connection between Cisco VPN Concentrator 3000 and Cisco RV220W / RV120W?
View 2 Replies View RelatedWe have two 3000 vpn concentrators. Under both of their load balancing fields, Configuration - Load balancing , the checkbox for loadbalancing is enabled.However both have different priorities, one with 10 and other with 1. Does this mean both are actually loadbalancing. What does the priorities indicate here?If we replace the concentrators with ASA , how will this load balancing need to be configured on ASA & how will it work.
View 5 Replies View RelatedI manage a VPN 300 concentrator which has been happily working for several years without any problems. All users are part of the same group and authenticate to an RSA server. We recently moved from RSA authentication manager 6.1 to RSA authentication manager 7.1. Everthing continued working fine for several weeks, then at the beginning of this week we started getting users intermittently failing to connect to the VPN. I'm not sure if this problem relates to our new RSA server, but we have other network devices which authenticate to it with no problem so I guess the problem is with the VPN concentrator itself.
When users fail they just get a generic "Reason 427 connection terminated by peer" error message. The live event log shows "group = vpn, status = Not-in-service" when their connection fails. Other times they connect normally and no error messages are displayed. There seems to be no real pattern, sometimes your connection fails but if you keep trying you will eventually get in [however it can take many attempts over an hour or two before you succeed, or you may get in straight away with no problem].
I dont believe its a network problem, as I have run continuous pings to the concentrator and the RSA server whilst users are experiencing these problems and there are no drops.
The RSA servers authentication monitor always shows that the user has successfully authenticated, whether the users connection actually succeeds or not. I am tempted to just reboot the concentrator, but we have site-to-site VPN tunnels connected off it and I'm a little concerned that if it is faulty it may not come back up at all.
We have to setup an IPSEC tunnel for a client that does not what to exchange private IP address information for security and overlapping address space reasons. We will both be natting our source private ip address space as public IP address space and send those packets through the established tunnel. Im using a Cisco 3000 concentrator.
View 1 Replies View RelatedWe recently had a Port Scan done on our external IP Addresses. One of those IP Addresses scanned was our Concentrator 3000. The report came back with the following TCP ports being open on the Concentrator 3000 - 80, 443, 1723, 10000, 10001, 10002, 10003, 10004, and 10009. I am unsure if it is necessary to have any or all of these open. The Concentrator 3000 is in front of our ASA5520.
View 1 Replies View Relatedis it possible to use cisco AnyConnect client to connect users with Cisco VPN 3000 appliance?If so how to configure VPN 3000 concentrator to work with AnyConnect?
View 1 Replies View RelatedIs it possible to configure a site-to-site VPN between an ASA 5510 running 8.2(1) and an old Cisco VPN Concentrator 3000? I've only been able to find an old 3000 to PIX guide on Cisco's site, and I cannot figure out how the two device's VPN options match up.
These are the options from the 3000:
IKE Proposal
Authentication:
Encryption options:
On the 5510's Site-to-Site Connection Profile, all the options are clumped into two boxes under Encrption Algorithms:
IKE Proposal: Encryption, Hash, DH Group, Authentication
IPsec Proposal: ESP Encryption, ESP Authentication
We have a pre-shared key configured, but I cannot find a set of options on the 5510 to match the 3000; I always get this error:
3Jan 24 201310:10:09713902Group = 63.192.x.x, IP = 63.x.x.191, Removing peer from correlator table failed, no match!1Jan 24 201310:10:11713900Group = 63.x.x.191, IP = 63.x.x.191, construct_ipsec_delete(): No SPI to identify Phase 2 SA!
For access by external users on our network use all Cisco VPN Client, we have a VPN3000 Concentrator and a Cisco ACS 2.6 for authentication.We wanted to upgrade to the latest release of ACS 4, x .... you can set a password expiration for VPN Client? Or make sure that the remote user can change password?
View 2 Replies View Relatedhow do I change my router password?
View 1 Replies View RelatedI'm very new to WCS and the bloke that configured the bludger has left the company. I'm trying to get into it but I don't have the correct username/password combination.
My query is: How does one do a password reset on a WCS server? Or failing that, is there a way I can ascertain the current unknown password?
I have access to the actual server itself, but not the WCS application. Searching around Cisco.com shows that apparently there is a utility that can be used to reset usernames and passwords however I can't seem to find it. The WCS version is: 4.2.62.11
I bought a new connection with this router, and the first time i tried to access it it had the default <blank> username and password it, so i changed it. But now i really don't remember what it could be. I tried to reset the router, but it still didn't clear the password. I tried to contact my ISP, and they said they can't access my router remotely, i had to reset it myself. I've tried to reset it many times (holding down the reset button for 10-100 seconds), but by PASSWORD won't be reset.
How can i reset it? Is there perhaps any other reset trick for it?
I don't remember my network password. How do I reset or recover it?
View 5 Replies View RelatedI need to reset my wireless password because I forgot it
View 1 Replies View Relatedtrying to reset my security password- and same problem as listed- tried using admin for admin and password for password at 192.168.1.1, but seem to have locked myself out.
View 1 Replies View RelatedI need to reset my wi fi password to 192.168.1.1
View 2 Replies View RelatedHow do I reset my password on my iPad? I have phone to enter a password on it and I don't remember what it is.
View 1 Replies View RelatedWe just took on a new client and they do not have the username or password for their ASA 5505. we need to reset to factory defaults. I have read some instructions online how to do this, but they require the password. How do we do it without the password?
View 4 Replies View RelatedI have Cisco PIX 515E for my Lab and can't recover the password. It is not connected to the network. I have configured server, address, gateway from the monitor mode and tftp not seeing my laptop. best way to reset or recover password.
View 7 Replies View RelatedI have been asked to do a network survey at a client. They are using the Cisco SGE2000 switch, which is new to me (used to working with 3750 switches). They seem to have lost the username/pasword for one the switches. Is there an way to recover from this, without reseting the whol config (not sure they even have a backup) ..
View 1 Replies View RelatedI lost my 192.168.1.1 password and how to reset it?
View 1 Replies View Relatedreset my username and password as my wireless network is not secure at this moment. I'm using the DPC 3925 cable modem which I've just purchased from Starhub.
View 4 Replies View RelatedHow do I reset my User Name and Password
View 1 Replies View RelatedI have a WBR-1310 D-link and was in setup this morning trying to fix my password cause the old one stopped working. Somehow I changed the password and no longer have access to the settings to change it to one that I can use to log on with my other wireless devices!!! Is there a way I can reset the whole thing? I mean something that makes sense to someone who is new to wireless internetting?
View 1 Replies View RelatedI forgot my user name and password to lock my router. How can I reset it.
View 2 Replies View RelatedI need to change my wifi password in beetel 450tc1.
View 1 Replies View Related