I have a new ASA 5505 that I am trying to configure. I've set up the basic stuff, and the router is getting an external ip address via dhcp. The router also has a site to site vpn link to another cisco ASA 5505 router. The site to siste vpn isn't working, but I can probably figure that out once the internet starts working. The router is getting an ip address from my isp, but I can't ping/browse to any web pages. [code]
View 1 Replies
I have a 5505 that i setup with a comcast cable modem (1 static address) and i cant seem to get to the internet. Im thinking it is a NAT rule but i don't have enough experience to figure it out.The current setup is E0/0 plugged into the cable modem, and a laptop plugged into E0/7. I have assigned my laptop an address within Vlan 1.[CODE]
View 19 Replies View RelatedI've having a problem with our company ASA5505 router.
We recently moved to a new adress, so everything had to be set up again. I have a static IP, submask and gateway from our new ISP. The router have been factory reset before moving. We have betweeen 10-20 employees on our LAN in the office. In an attempt to make things easier I have changed the internal IP (and IP range) to 10.0.200.1 with a range from 10.0.200.5 - 10.0.200.100 as our NAS/printer/plotter have IPs within this range.
I can ping machines on the internal IPs and in ASDM the Outside interface is show as "up" with a green arrow. But there still isn't any internet connection. The only thing I haven't tried (because people need the current network to be online) is changing "route inside 0.0.0.0 0.0.0.0 62.242.X.X 1" to "route outside 0.0.0.0 0.0.0.0 62.242.X.X 1"
I have recieved a primary and secondary DNS adress as well, but I'm in doubt as to were I'm supposed to enter these (Using ASDM Version 6.3). I would like everything "Behind" the router to be run by DHCP.
Here is the running config:
ASA Version 8.2(2)
!
hostname ciscoasa
[Code].....
I am trying to configure DMZ on ASA 5505, basic license. After changes I have made I cannot access Internet from DMZ. I think I am missing an access list for DMZ, but I am not sure.
interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1 !interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5switchport access vlan 3!interface Ethernet0/6!interface
[Code].....
I am a network Engineer but had no experinece in Firewall, right now i am under a pressure to take care of a ASA 5505 were all the VPN and Inbound and out bound were configured, recently i had some changes done and re done the change, but unfortunately it removed some configuration which are ment for VPN, now i am facing a problem,
VPN connection establishes but unable to browse internet is my problem, i tried inheriting the Split tunneli, but i coudnt get through it it seems, i doing some thing in a wrong way, i here use mostly ASDM,
i ll paste the Configuration for investigation,
ASA Version 8.0(4)16
!
hostname yantraind
domain-name yantra.intra
[Code]......
I have basically started fresh, from a clean image. We bought these with the expectation that we would be able to configure them using the GUI for what we need, which up till this point doesn’t seem to be the case.I will tell you how I have this setup, I have our ADSL going to a modem acting as a bridge with a static IP supplied by the ISP. If i connect a laptop to that modem and set the static ip on the laptop, I get internet access fine.So I then connect the modem to ethernet0/0 and the laptop to ethernet 0/1 I connect to the ASDM and run the startup wizard with the following:
· Outside ip : 87.87.87.87 255.255.252.0 (this works on the lappy straight to the modem)
· Inside ip : 192.168.10.1 255.255.255.0
· No dmz
[code]......
First time attempting to set up a 5505. Trying to replace a snapgear firewall and replicate the settings to the 5505.
View 12 Replies View RelatedI have a 5505 ver 8.2 connected to a router with a T1 internet connection. There was a problem with the internet service and when it was resolved the ASA did not pass traffic to the internet until it was power-cycled. Unfortunately that's all the info I have, as I was not onsite and couldn't access the ASA.
View 3 Replies View RelatedI am using ASA 5505.Below are my sh run.I am not able to ping my gatway i.e 182.73.131.89
interface Ethernet0/0
description Internet Interface
switchport access vlan 61
!
interface Ethernet0/1
description office Internet
switchport access vlan 50
[code]....
I have not been having much success configuring my 5505 for Internet access, and I'm sure there are a few small things I'm missing. At times I believe I got it to the point where I could ping, but still not pass through the Internet traffic. At this point, I reset the 5505 and only changed a couple of settings. I have an external range with these characteristics: Network Address 67.139.113.16 (.17 is Gateway), SM: 255.255.255.248, available IP: 67.139.113.218 The external connection is through a T1 modem, and when I put those settings in my laptop, I can access just fine. When I went through the startup wizard in the ADSM, I maded the internal interface 10.209.0.3, subnet mask: 255.255.255.0 I selected PAT in the Wizard, but don't know if I should have, or if the NAT rules I tried to put in are fine. Eventually I want to add a Site to Site VPN to the rest of the 10.0.0.0 network, but I can't even pass the Internet through to the inside. Also, this will eventually be behind another hosted firewall, so I'm not worried about restricting access, even currently. However, I suspect the problem is that traffic is being blocked with the NAT rules or Access rules.I wish I could just disable those inherent deny rules Outside of pings to 10.209.0.3, all pings come back as request timed out.
Config:
: Saved
:
ASA Version 8.2(5)
!
[Code].....
is it possible to configure an ASA 5505 with two internet connections? One dedicated for VPN and the other one for Internet access only.
View 9 Replies View RelatedI have configured Site-to-Site IPSec VPN and it works. Our clients have access to inside network and Internet ("hairpinning").How can I configure access to Internet on remote networks clients if VPN tunnel fail?Remote devices is ASA5505 and Cisco 861.When VPN works i have access to Internet over central office gateway.In case when VPN fail i need still have access to Internet over local (remote device) gateway.
View 2 Replies View RelatedI am trying to configure Nat on a clean ASA 5505, but can't get it to work. I ran the commands below. On the ASA I can ping the internet and inside vlan ip. On my laptop I can ping the ASA inside vlan ip, but I can't ping the outside vlan ip. From another network I can ping the ASA outside public ip. Is there an access-list that denies inside from accessing outside?
I am running version 8.4(3) and I erased the existing configuration.
ASA(config)# interface vlan 1
ASA(config-if)# ip address 10.0.0.1 255.255.255.0
ASA(config-if)# nameif inside
[Code].....
I want to access my ASA 5505 from internet.how I can achieve it.
View 1 Replies View RelatedI have an ASA 5505 behind my internet router. i have got only one public ip configured on the router outside interface.192.168.20.0/24 subnet is configured between ASA and router and inside network is 192.168.10.0/24 (Refer the attached diagram).
I have exposed my mail server and ftp server to public through static PAT in router and ASA with the same public on router outside interface. Iam facing issue some of the machines inside my network internet is not working(actually DNS is not resolving) some of the PC's internet is working fine some of the PC's randomly working. i have attached the diagram and ASA config , after this issue is sorted out i need to configure a L2L VPN to my head office.
I have an ASA 5505 which is unable to acces the internet, even when reloading just the basic config.If i setup my laptop with the outside ip or another ip in the subnet, it does work.
[code]....
I have a Cisco ASA 5505 that has been configured to act as a router as well. I have configured 3 VLANS that have access to the internet. For some reason the "InsideWifi" and the "Guest" VLANS have very slow internet speeds and sometime web pages wont finish loading properly. The "Inside" VLAN gets the speeds that are expected. The DNS server does reside on the "Inside" VLAN. Is there anything wrong with my configuration that would cause the internet speeds on the other VLANS to be slow? My config is attached.
View 6 Replies View RelatedWe currently use a linux software based firewall called IPCop that sits between our network and router (This is in bridged mode) IPCop conects over PPPoE and everything works fine.
However the system is not reliable and I fear not that secure so have purchased an ASA5505 now I have added the PPPoE info to the device using the ADSM software however although it picks up my external static IP I'm unable to access the internet. On IPCop I only had to enter the broadband credentials and it worked however I feel like I may have to add more to the Cisco, for example do I have to specify DNS servers and do I have to set a static route?
Here is my config file so far (Note I think I have turned on the ability to ping from internal to external). My config I have done through the ADSM as opposed to the CLI
: Saved:ASA Version 8.4(3) !hostname ciscoasaenable password 8Ry2YjIyt7RRXU24 encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface
[Code].....
I'm trying to allow SSH traffic from the Internet to my DMZ. I gave my remote guy my ip and he can see the ASA 5505 but not get into the DMZ. The outside is 70.165.19.137. The DMZ server is 192.168.60.2. I have the inside talking to the DMZ fine. [code]
View 9 Replies View RelatedI recently bought an ASA on eBay the plan was to try and learn how to configure them and get more familar with Cisco's ASA hardware etc.
I want it to do the routing for my home network. The way things are setup at the moment is pretty standard. I have an ADSL modem which is also a router which was provided by my ISP (Orange).
The first thing I did was change the router to be in "modem only" mode which seems to have worked. I then got the ASA to use PPPOE by following this guide [URL] I assume that worked as it is authenticating with the ISP and I'm getting a puplic IP address assigned to the outside interface. The default gateway is being set by the "ip address pppoe set route" command which I have verified with the "show route" command. The problem I'm having is that even though I'm getting a public IP I can't ping any thing from the ASA I've pinged 8.8.8.8 and 4.4.4.2 using the outside interface as the source but I'm not getting any responce. I have tried changing the MTU a few times to different amounts on the outside interface with no luck.
I set up an ASA 5505 at home through PPPOE connection. The ASA seems to obtain an IP address correctly.and I can ping a public ip address using the outside nic, but not the inside nic. I saw the error message when I ping: No route to ff0213 from fe801bc2b1288cd5bc1. As a result, I cannot connect to the Internet.
View 11 Replies View RelatedHow do I configure Cisco ASA 5505 (using ASDM 5.2) to block a workstation (IP address) from accessing internet completely? I was trying to set up a new incoming access rule for outside interface to deny any IP traffic to that workstation but it doesn't work from some reason - the workstation can still access the internet. The ASA has no special settings, only a few ports opened for servers?
View 1 Replies View RelatedThere are three different sites, two are composed of Multilayer switches cisco 3560 and 3570 as core switches (a 3560 in one site and a 3570 in another site), the last site doesn't have any routers just a 2950 switch. Each site has two asa 5505 as firewalls. Two Internet connexions are connected to every site, one on every firewall. One Internet line is used to connect the different sites together using VPN crypted with IPsec and the other line is just for Internet access. The line that is used to interconnect sites contains voice and data traffic.At the moment all the routes are static routes, the network isn't too big for now and counts not more than 20 subnets.But it is evolving, and I want to use dynamic routing, EIGRP to be more accurate. I've looked into it and I'm not sure how to make it work. The VPNs active on the ASAs don't support dynamic routing, so I thought about GRE tunnels but the ASAs don't seem to allow it either.
View 11 Replies View RelatedI'm trying to configure a second server on my network but whenever I add the static NAT rule, the internet stops working on that computer.
Here's my Cisco ASA configuration:
ASA Version 7.2(3)
!
hostname domain
[Code].....
I have config ASA 5505 and it is conencted to layer 3 switch that connects to cable Modem.
ASA is config with DHCP option and PC is able to get the IP from ASA. But from PC i am unable to access the internet. From ASA itself i am able to ping the Websites fine.
ASA has config with DHCP for inside and also it is doing NAT.
When i connect the ASA directly to Cable modem then pc is able to access the internet.
I have setup 5505 ASA for Testing purposes. It has static route to layer 3 switch on outside interface that goes to the internet.
ciscoasa# sh route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
[Code].....
I am trying to “build up” a small home-network and using some of following Cisco equipment’s
ASA 5505 v8.4.3 witch base licenseCisco Catalyst 3750G with ipservices version 15.0.xand 1 qty of AP1142N I am not able to get internet access from any VRF’s.
From "MILAN (LAN) VRF, I am able to ping my gw: 10.45.45.1 but I am not able to ping for example: “linknett VRF”.
It seems that i am missing some NAT rules on ASA or ?
If i connect my laptop directly to the ASA, i am able to get internet access!
I am not feeling comfortable with a new ASA 8.4 code yet, so im not so sure which exact code's i am missing on ASA ...
attached digram including configuration files from ASA and 3750 sw.
I would like to restrict Internet traffic (HTTP & HTTPS) for Inside Users with an ASA 5505. I would like to setup a proxy-like system where a User/Password must be entered before the User can actually browse the web.
I know that this can be done with an additional RADIUS/TACACS+ Server. Is this also possible without any external AAA Server, so with User/PW stored on the ASA locally only?
I have configured the ASA 5505 for internet access and outside users to use two servers in the DMZ. Every thing is working fine. When I was configure VPN, I did some mistake I guess, now inside users are not able to access internet. They get an error 405. Thats an error. The request method XXX is inappropriate for the URL /. Thats all we know. Even I am not able to access the server in the DMZ from outside and I get an error : Bad Request - Invalid HeaderThese things just happend after I did some thing on the ASA. I copy and pasted the my old configuration but still insider users are not able to connect to internet and from outside I am not ableto connect to server. The weired thing is that I can user VPN with out any issues. I can connect to vpn but I cant access any internal resources. Even inside users are able to ping internet addresses with out any issue.
View 2 Replies View Relatedi have asa 5505 , so i wanna my inside network to access to the internet. my internet gateway is 155.155.155.1
: Saved
:
ASA Version 8.2(1)
!
interface Vlan1
[Code]....
I changed a configuration and suddenly I lost the internet connectivity... Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasaenable password qVQaNBP31RadYDLM encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 !interface Vlan2 nameif ATT security-level 0 pppoe client vpdn group ATT ip address pppoe setroute !interface Ethernet0/0 switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!ftp mode passiveclock timezone EST -5clock summer-time EDT recurringsame-security-traffic permit inter-interfaceobject-group service DM_INLINE_TCP_1 tcp port-object eq ftp port-object eq ftp-data port-object eq wwwaccess-list ATT_access_in remark Linkstation Accessaccess-list ATT_access_in extended permit tcp any host 99.23.119.78 object-group DM_INLINE_TCP_1 access-list ATT_access_in remark Linkstation
[code]....
I found a tricky task for our ASA 5505 firewall. I am not able to go internet when using DHCP but I can access by using fixed IP address in client PC.Same IP, Same Mask, Same DNS, Same Gateway. All the same but no hope. Any configuration i missed in firewall?
View 5 Replies View RelatedI'm unable to have any internet connection for my new setup.
here's the overview.
Current setup is
Internet -> Router -> PIX 501 -> Switch -> clients
Internet -> static ip given is 210.193.34.1 - 210.193.34.6
Router -> Static ip assigned for NAT/External is 210.193.34.1, Local ip is 192.168.1.246
PIX 501 setting ->
IP to Router, According to router screen is 210.193.34.2, but not sure what settings are done in the PIX itself as I'm unable to access it.
local ip is 192.168.1.1
Clients - > 192.168.1.0
Old setup is working fine and connected to internet. for the new setup, as i do not want any downtime for the old setup.
As you can see, there are two firewalls connected concurrently to the router. I've configured it this way.
Internet -> Router -> ASA 5505 -> Switch -> clients
ASA 5505 setting ->
IP to Router NAT/External/ Outside Interface, 210.193.34.6 (Or do i set as 192.168.1.0?),
local ip/ Inside Interface is 192.168.2.1
Clients - > 192.168.2.0
some setup details.
security policy, NAT, set to default. routing is route outside 0.0.0.0 0.0.0.0 210193.34.6
I'm unable to access after a week of troubleshooting.
