I am going to configure ospf on cisco 1721 router but when I give command
conf t
router ospf 116
it does not show (config-router)
I am attaching sh run and sh version herewith attachment
I have 2 ASBR routers, AGFR01RTR03 and AGFR02RTR03, performing OSPF to OSPF redistribution in both ways for the same ***. They also do summarization for our private addressing scheme. It is all working just fine for that part (neighbors, summarization, redistribution).
AGDC01RTR01 --- AGDC02RTR01 (OSPF 1000 ABRs)
| |
| |
AGFR01RTR03 --- AGFR02RTR03 (OSPF 1000 / 53 ASBRs)
Let's focus on AGDC01RTR01 with a specific entry here (IP subnet is fake) :
Routing entry for 1.1.1.0/25
Known via "ospf 1000", distance 110, metric 300, type inter area
Last update from 10.2.244.76 on GigabitEthernet5/1, 1d03h ago
Routing Descriptor Blocks:
* 10.2.244.76, from 10.2.1.249, 1d03h ago, via GigabitEthernet5/1
Route metric is 300, traffic share count is 1
[code]...
Currently the OSPF network consist of 2 segment route via static route.One is AREA 0 and another AREA 10.Both network are seperate entity, only static route to route between 2 networks.But the static route do not provide the dynamically and flexibility, I plan to run routing between 2 networks via VLAN160 and VLAN162.
I still want to manitnace it was 2 different OSPFrouting domain.Can I run OSPF with differrent OSPF porcess ID?
configuring VPN in my cisco 1721 router to connect in vpn client
I have the public IPs.
I have a 1721 router with 3 equal routes to 0.0.0.0, using CEF for load balancing with universal load balancing algorithm. It doesn`t NAT, just routing. I wonder which is the maximum capacity of the router, since it should support up to 40000 connections to different destination IP. Is the limit set by the router resources (CPU, memory, ...) or a maximum limit of entries in the table FIB / RIB?
View 7 Replies View RelatedTrying to work out if I can setup a VLAN interface on a 1721 router.The only interfaces that are listed are the Ethernet (W1-ENET) and the Fast Ethernet interface.I'm still super new to all of this and learn how to change IOS via rommon and TFTP after realizing I had an IOS too large for the memory?
View 3 Replies View RelatedMonday, I had a cisco 1750 router in place suddenly stop communicating to a Larscom ISP owned unit. Since then I have sent two replacement 1721 routers with WIC-1ENET cards. I have used the original straight thru cable to connect the 10baset port on the Larscom to my E0 on the WIC-1ENET. No link lights on either. I have also tried a known working straight thru cable and a crossover cable. No link lights.
I can take a crossover cable from a pc and ping the E0 port without issue. The ISP is telling me it is an issue with my equipment.
I am in the process of configuring two vpn tunnels on one interface of cisco router series 1721. Any link or document with more information?
View 5 Replies View RelatedI have the Cisco series “Cisco 1700” routers operational at my client site, These router suddenly get reboot with 1 or 2 hrs gap. See the below errors which has been captured in router logs:
============================================================
00:00:09: %SYS-5-CONFIG_I: Configured from memory by console
00:00:11: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-Y-M), Version 12.2(16.1)T, MAINTENANCE INTERIM S
OFTWARE
TAC Support: [URL]
[code]....
I managed to setup a 1721 router as a vpn server connecting to it using a cisco vpn client however altough I am obtaining an ip address as defined in the dhcp pool I am unable to communicate with both the remote network and also I have no internet as soon as I connect.
View 5 Replies View RelatedIs it possible to set up a vpn tunnel on a 1721 router that uses the following ios:
c1700-y7-mz.124-13b.bin
I thought I had read somewhere that tunnels were not supported on the 1700s but wanted to make sure. If they are I would like to know if they are supported in the above ios.
I have cisco 1721 router so I installed an ethernet interface card so when I make show run I found that there is a fast ethernet 0 and ethernet 0 (which I installed) so i wand to make subinfaces of the etheernet 0 but I can't. I tried to make encapsulation dot.1q but it doesn't accept it.
Is Ethernet0 supported to generate subinterfaces?
Long time since I have had to configure a router and have a small project
Here is what I have in a simple diagram:
PC(static IP)--to--Switch--to--(Ethernet0 int, WIC0)1721 router(FastEthernet0 int, built-in)--to--Switch--to--PC(DHCP)
I need static IP PC to be able to ping the DHCP client. Static IP units 10.1.1.x/16, DHCP clients 10.1.3.x/16.
I have found these overlap and thus give errors and will even shutdown the interface if I enable certain things like routing or bridging.
So I gather I need to change one interface IP range, which would be the DHCP side, I need to stay 10.1.1.x/16 for static side.
enable dot1q encapsulation on two ethernet ports on a 1721 router. I am able to configure it on the built in fastethernet port, but not on any interface provided by a WIC-1ENET or a WIC-4ESW. I have an application that requires two physical ethernet ports that support dot1q encapsulation.
View 4 Replies View Relatedi got a big problem, during a configuration reset i got an electrical blackout. I have set the configuration back after a password reset and send the reset prompt. At the restart of the router the blackout take all for 10 seconds out. When i restart the system an connect the router with the hyper terminal i get the following output:
[Code].....
I think the config was lost but how can i restart the router and enter a new one?
I am working on a backup system for my WAN. Verizon quoted the HWIC-3G-CDMA-V to work with my Cisco 1721 router. I have a bunch on these routers on a shelf and thought I would use them for the 3G network. Looking at the Cisco web site it does not list the 1721 as being able to work with this HWIC. I thought it might not be listed as the 1700 series are End of life. Whether it will work?
View 3 Replies View RelatedI would like to know can we configure vlans with cisco 1721 Modular Router? Is it Possible to configure lan environment with the vlans configured in 1721 router without a managed switch?
View 9 Replies View RelatedMy internet is T1 by Verizon. My mom's company Siemens pays for our internet because she works from home as medical tech support on the phone. Okay so the T1 had to be laid out to our house underground I think because where we live, other brands of internet aren't available. The T1 goes from the box outside into our basement and hooks up to a Cisco 1721 modem. From the 1721 the internet goes out to a wireless router that is sitting right next to it. This wireless router is a Linksys WRT160N V2. We have several cables coming out of the WRT160N V2 to go to the first floor for hardwired connections, but one cable goes to the attic and connects to a second wireless router. The second wireless router is a Linksys E2000. We have several cables coming out of the E2000 that go to the 2nd floor to serve as hardwired connections.Okay so let me explain where things went wrong.
After a storm our power went out. Eventually the power came back on, but every now and then our internet would shut off for like half a day then turn right back on, so our internet was getting really really spotty. The [b]AL[/b] light on the Cisco 1721 would come on every time the internet went out. It was so bad that my mom had to get an aircard from verizon to get internet. So after two weeks of spotty service and arguing with verizon trying to get them to come fix the problem, they said try resetting your wireless routers because they might have "bad data" in the lines causing spotty connection. So we reset the wireless routers by holding down the reset buttons on the back. Well.. this reset all of the settings for the routers which Cisco facilitated set up, and now our wireless routers are out of warranty date so they can't set the wireless routers back up. However, we have copies of the online wireless router set up page, so we thought maybe we could just set them up ourselves.Well the problem is... We don't know how to connect to the wireless setup pages.. I read something on the internet about setting up wireless networks and to type 192.168.1.1 into our browser(Mozilla Firefox) and that would bring us to the wireless setup page. But the page does NOT ever come up.
Another way to find the IP address of our wireless routers would be to try going to the cmd and typing in ipconfig and using the Default Gateway IP address for the browser to connect to the setup page but that doesn't work out either.... Right now I unhooked the Linksys WRT160N V2 and hardlined the Cisco 1721 to the Linksys E2000 to a PC on the second floor because I figured it wouldn't work out if we had two wireless routers running at the same time. Currently the browser is taking me no where at all. It just says "Connecting..." but nothing is loading up at all.I tried hardlining from the Cisco 1721 to my mom's laptop, which is her work computer, and I got no response at all. I figured it might just be her work computer that was messing up and not allowing her to hardline into the 1721 so I tried hardlining the Cisco 1721 straight to the PC desktop on the second floor(we have no other laptops other than my mom's work laptop) and nothing went through. Then my dad says the Cisco 1721 has been configured so it doesn't direct connect, meaning that it has to go through a wireless router.
I am using a bunch of Cisco 1721 routers for my T1 lines. We recently purchased Digi cell modems as a backup for the T1. On configuring vrrp to work on both devices I discovered that IOS 12.3(6c) does not support the "vrrp track" feature. After reviewing the Cisco Feature Navigator I could not see an IOS that will support the vrrp object tracking. Is that correct? The routers have T1 WIC's installed. If it does work what is the latest IOS that will work on this end of life product?
View 1 Replies View RelatedI am running IPv4 with OSPFv2 currently. However, I planed to deploy IPv6 in my network. Is it possible to deploy V6 with OSPFv3 without affecting current network traffic in V4?
View 7 Replies View RelatedI have a scenario with a Cisco 6506 and a 7206. The 6506 is running BGP and peers with our data center router. The 7206 is a stub router off the 6506 and is used as an edge router for customer T1 circuits. I want to use OSPF between the routers to exchange connected and static routes. The problem I have is that static BGP null routes on the 6506 are overriding the OSPF routes being received from the 7206. Example: The 6506 is advertising a class C network 192.168.1.0/24 to our data center. The 6506 does not utilize the 192.168.1.0/24 network. It is only used on the 7206 for customer T1 circuits and is carved up into /29 subnets. So the 6506 has a static route: ip route 192.168.1.0 255.255.255.0 null 0. Today the routing is accomplished with static routes on the 6506 for the 192.168.1.0 networks on the 7206. Using OSPF the 7206 advertises /29 links back to the 6506, but when I withdraw one of the /29 static routes from the 6506, the /24 null route takes precedence over the more specific /29 routes and the traffic is black-holed on the 6506. how can I get the OSPF routes to look preferable to the /24 null route on the 6506?
View 7 Replies View RelatedI have a Nexus 7K router, has 2 ospf process, ospf 1 and ospf2. OSPF1 has several subnets in 10.1.0.0/16 subnet range , OSPF2 has several subnets in 10.2.0.0/16 subnet range. I want to summary OSPF 1 subnets to 10.1.0.0/16 then redistribute to OSPF2. but it doesn't work. [code]
View 2 Replies View Relatedi'd like to monitor the OSPF process of my MPLS routers by SNMP. I created templates for
ospfIfEvents
ospfNbrEvents
ospfSpfRuns
ospfNbrState
ospfAreaLsaCount
but when i configure the poller i believe the data i mixed up somehow. I for example i don't get all neighbor in the ospfNbrState. i tried with snmp context configuration but i am not sure if this right what i did.
On a 4507 v12.2(20)EW, the connected subnets which are declared in the ospf instance are not propagated to the MPLS carrier router.Only the static routes which are redistributed in the ospf instance are propagated to the MPLS carrier router.
View 1 Replies View RelatedI have a 1721 router in my home & I want to setup it for firewall/ vpn. Is it recommended to purchase a WIC-1ADSL? What module is recommended for VPN? Is it possible to setup VPN using DSL / Dynamic Ip connection ?I want to explore on Cisco security & I get this advice from a supplier.
View 1 Replies View RelatedI can access the LAN environment 10.1.1.X from 20.1.1.X but cannot get out the gateway to the internet? The linksys gatway model is a WRV54G.
View 4 Replies View RelatedI've got three Cisco 1721's and a 2610, two of the 1721's are 32f's, the other one is a bit older but is still the same model. The two Cisco 1721 32f's have 1-dsu-t1-v2 wics in them, and the older 1721 has a 1-dsu-t1 wic in it. Now no matter how i have configured it the old t1 wic will not talk to the v2 wic. I've tried putting the old wic into a 1721 32f and it doesn't work at all!
What i have working:
router DCE (1721 32f with v2 wic) can talk to router DTE (1721 32f with v2 wic) no problem with this configuration.
Router DCE:
-service-module t1 clock source internal
-service-module t1 data-coding normal
[ code].....
Router DTE:
-service-module t1 clock source line
-service-module t1 data-coding normal
[ code]....
Router OLD (1721 with v2 wic) can talk to router DTE (1721 32f with v2 wic) no problem with same config. What doesn't work: Any router with 1-dsu-t1 (old) wic to router DTE (1721 32f with v2 wic). again same configuration as before, so whats going on that i cant get this to work? Is the old t1 wic not compatible with the new t1 wic?
I am having a problem configuring a VPN connection from a 1721 router to an ASA5520. The router has already been configured, but I have been asked to setup the VPN.I think the issue is because they are using a Loop back interface (which I have never configured for before).
The "sh crypto isakmp sa" command shows:
dst src state conn-id status
5.6.7.8 1.2.3.4 QM_IDLE 4 ACTIVE
where 5.6.7.8 is the ip on Loopback0, 1.2.3.4 is remote peer ip. Pings to the remote network don't work.
Here is the (slightly edited) config of the 1721 :
Current configuration : 3838 bytes!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[code]......
Can Cisco 1721 act as DNS proxy? If yes, how can I configure it?
View 5 Replies View RelatedI can not apply the LLQ to ADSL ATM interface. the system take the command with out any error message, but no in the show running config. Any Cisco link can explain this? [code]
View 2 Replies View RelatedI just purchased one of each of the above, both with 1ea WIC 1DSU-T1, and would like to connect them directly to each other in a lab scenario. Do I need to have an RJ48 cable or will an RJ45 work? I have them connected now, but they are not seeing each other. They are connected via S0 on the 1721 and S1/0 on the 1760.
View 5 Replies View Relatedrouter 1721 with one wic-1adsl ,i have adsl conection with irb static ip. the router connect with mannaged switch through a trunk port. the switch has 2 vlans one for the static IPs and the other for private lan. i need the private lan to be able to go to internet. vlan2 can go to internet because it has the same subnet with provider but vlan 1 canot go internet, so how i can make all vlans go internet(the router has only 1 fastethernet port)
View 4 Replies View RelatedI tried to configure a 1721 router, but he can't connect in my server. I follow various how-to in the Internet.
View 2 Replies View Related